D-Link DIR-655 :: Cannot Connect Network Radios After Upgrading To Latest Firmware
Mar 21, 2011
Cannot connect network radios after upgrading to latest firmware. Could connect before upgrading firmware but throughput was slow for computers and streaming. Now I can connect computers, but not radios. They connect ok using Belkin and Linksys routers.
I just upgraded to a E3000 from a WRT54G and I am having some issues with network speed.I have no special settings and have even tried restoring factory defaults and upgrading to the latest firmware to no avail.The time I notice the biggest hit is when transferring files locally on the network (WiFi and LAN).Let me note that I do know the difference between MB/s & Mb/s and the like.I have Comcast 20Mb/s Down, 1.5Mb/s Up (just a FYI, the main issue is local transfers)
With default settings my Laptop (ASUS N82JQ, Atheros AR9285 Wireless Network Adapter), connects to the router at only 65Mb/s (with full signal).Upload seems to be more decent ~600KB/s (Transferring files from wireless n laptop to the gigabit desktop).Download seems to be limited to ~150KB/s (Copying files from the wired gigabit desktop to the wireless n laptop).These speeds are horrible! ~5hrs to transfer 3GB of data!
One of my laptops had a card that was capable of both 2.4 & 5Ghz and I was previously getting ~2000-5000KB/s (2-5MB/s) transfers with this router (But I had to do a system restore on it and reset the router). My ASUS laptop seems to only work with 2.4Ghz though. If I change the 2.4Gh Wireless settings on the router to "Auto(20MHz or 40MHz)" the laptop will connect at 150Mb/s, but the speeds are the same slow speeds as above.
I was using Remote Desktop between two home computers hard wired through the router and a switch. Now after upgrading to firmware 1.35 I can't get remote desktop to connect. I get an error that I may not have permission, etc. I have the DIR 655 ver A and am running Windows 7 professional on both computers.
I bought the DIR-615 router from Futureshop awhile ago because my Linksys WRT54G router keeps dropping connection every couple of hours. I have to unplug the router and re-plug it in order for it work again. On the DIR-615 admin page, it states Firmware Version: 5.10. Is this the latest firmware?
I'm trying to upgrade the firmware because I still experience connection drops from time to time (but not as much as I did with WRT54G)... it usually occurs when multiple devices are pulling signal from the router (for ex. PC#1 + PC#2 + laptop). I've just disabled "Short GI" as mentioned in another forum post here.
what is the latest firmware version for d-link dir-825? It tell me that i currently got the 2.60VT, is it the last one? If no, where can i download and how the latest version?
Where the list of changes for the latest firmware version can be found? My new DIR-655 has firmware from May 2010, and I see the latest and greatest on the DLINK website is from September. But it doesn't state what the changes are, so I'm not sure if I should upgrade or not.
I've been lagging really bad when my sister uses the laptop upstairs with wireless connection. Just 1 computer makes me have up to 100 ping, imagine 3. How can configure my settings so that i will stop lagging or configure so that i have priority.I have a Dlink 655 Version A4 with the latest firmware 1.35
I'm running a D-Link DIR-655 Hardware Version A3, Firmware Version 1.21. In the past, it has been flaky, and I considered updating to the latest firmware (1.3+ something), but everywhere I read (mainly this forum) said it might be WORSE for the router and couldn't even be downgraded, so I decided to ride it out.
Eventually the problem disappeared and I forgot about it, but now it's back with a vengeance. Recently I opened up a Guest Zone so my neighbors could borrow wifi, and I occasionally run torrents. Torrenting seems to definitely crash the router overnight, while it also seems to randomly bug out, possibly when the neighbors are using the Guest Zone. The Guest Zone might be responsible, but I have no idea.
For what it's worth, I don't think my neighbors are terribly tech-savvy, so I doubt they're filesharing or doing anything risky. They might have malware installed, but I don't know.
Is there a way I can diagnosis my precise issue, should I go ahead and update to the latest firmware to try?
I've been having some issues with my DIR-825, it's been intermittently dropping internet connection. This is across multiple OS (Win 7, Ps3 OS, iOS, etc.
I have a DCS-942L. Everything was working fine on my setup until I upgraded the firmware the other day. In the mydlink.com website when I logged in that day, it stated a firmware upgraded was needed. So I clicked on upgrade, let it run its thing and then tried to view the playback and now the thumbnails are just black and when I click on one, it looks like it is loading but then shows the quicktime icon with a question mark over it. I upgraded my Quicktime component and that didn't fix it either. So I went into advanced settings, downloaded the new firmware upgrade from there by saving the zip file and uploading it via the advanced settings website, and still nothing. I have another camera, same setup, that I have not upgraded firmware on yet and that playback is working fine.
With firmware version 1.31, the Wireless settings page is blank when a browser other than Internet Explorer is used to access it - for instance, Firefox or Chrome.All other pages appear and seem to work properly, only the Wireless settings page is empty. Luckily, the Wizard still works and can be used to set the Wireless settings for general purpose use. Older versions of the firmware worked fine with other browsers, including the Wireless settings page.
I just have an old Dlink DIR-615 Wireless router. I have some problems with it and need to improve it... So, what is the best option... buy a new DIR-636L or 657 router or install the latest ddwrt firmware on the existing one?
Region : NewZealand Model : TD-W8960N Hardware Version : V3 Firmware Version : 1.4.0 Build 111130 Rel.56405n ISP : Snap
I just bought a v3 TD-W8960N and I'm trying to see what is the latest firmware available?On the modem it came with 1.4.0 Build 111130 Rel.56405n.When I look on the website the listed latest version is w8960nv1_un_1_4_0_111108R40398.up (that is the file inside the zip package/link TD-W8960N_V1_V3_111108)Which is the newer version? The revision number on the firmware that came installed kind of looks like it is actually newer. But if it is newer, why is not available for download from TP-Link?
Region : UnitedKingdom Model : TD-W8961ND Hardware Version : V3 Firmware Version : 3.0.0 Build 120524 Rel.05221
I have just bought this ADSL router. Of course, the first thing I did was upgrade the firmware, or so I thought.It seems that the firmware on the TP website is older than the one which was pre-installed onto the router.Website Firmware: 3.0.0 Build 120524 Rel.05221 ------------- i.e. 24.May.2012 Release 05221.Pre-loaded Firmware on router: 3.0.0 Build 120808 Rel.28888 -------------- i.e. 8.August.2012 Release 28888.I have foolishly uploaded the older firmware to the router from the website. I wanted to see what version number showed in the Router's Firmware page so I did a ROM backup, thinking I could always reload the "current" firmware. As it turns out, the ROM file is just the user settings backup.
It is sad that TP-Link doesn't provide change logs. Where to find later firmwares, or even what the change to the firmware was?And when we can expect a new firmware to be uploaded to the website?
Region : Denmark Model : TL-WDR4300 Hardware Versin : V1 Firmware Version : 3.13.23 Build 121225 Rel.37950n ISP :
my TP-Link USB Controller after my latest firmware upgrade, and therefor my USB-printer (connected to the router) do not function any more, and i can not find a new software for the Controller
Region : Iraq Model : TL-WDR4300 Hardware Version : V1
have TL-WDR4300 router hardware v1 but when update to the latest firmware it became unstable and disconnecting so I had to return back to older firmware the new firm ware released 12/25/2012 and it is noted for TL-WDR4300(UN) V1 my model is TL-WDR4300 V1 not (UN) so what is different between the two
I currently have this router in use with verizon dsl (PPPoe) setup.I have this set to "always on". Since the verizon modem, which is also router has been set into bridge mode and the d-link came into play its been extremely slow, and dropping connection. The router is in a separate IP class, and has no conflict with the modem. My question is, if I upgrade this firmware from 1.0 to 1.02 will it default to factory settings? I know it says only some will. I do have the backup config file, but i would be doing this remotely, and would not be able to get to this router if it goes down. Has anyone gone from 1.0 to 1.2 and saw a difference and speed, and are you able to do this without losing settings.
Whatdoes it require?. What is the current version? What do we need for upgrading? Are there specific codes or new need to buy new products? In case of buying new products, which are the configurations?
What is the latest firmware version for the F9K1109? I found a link to the 1.10.16 code and downloaded it upgraded the firmware but the website seems to indicate 1.00.49 is the latest.
We have Sg-300-28 serious switches(SRW-2024 k9-EU) and i want to upgrade switch with latest firmware, any info for latest firmware is used for the same ?
I have WRT300N V1.0 with Firmware v1.03.6.what is latest Firmware for WRT300N V1.0 and where I can get it.I tried at Downloads under Support in Cisco website but it said "No firmware/driver download available".
I have a WRT54GS v1 router which is currently loaded with firmware version 2.07.1. I want to upgrade it with the latest firmware. Where I can find the latest firmware download for this model router? Linksys does not have it available on their site.
Can't download newest firmware for F9K1102/N600 DB Router. I am on 1.00.19 and there are two newer firmwares, the latest being 3.03.12. This firmware is suppose to allow support for Windows 8. All my computers now have Windows 8 so I want this firmware, but I can't download it because the link provided by belkin no longer exists
Just purchased a Belkin AC1200 Router Modem and unable to locate the model number what is the current firmware version It is the UK model and I guess it must be very new?
I have a SF300-24P switch running version 1.1.2.0 firmware. I want to get to the latest release (1.2.9.44) - can I upgrade directly to the latest code or do I need to step through all the versions in between?
I need to get the latest firmware for a 2811 router but I am unable to download it. What is the best way to get hold of this can I just contact a local Cisco reseller n Monday or is it more complicated than that?
I have a linksys router(befsr41 v3) with the latest firmware(1.05.00) - i have been using it for at least 7 or 8 years now - at one time i had 3 computers hooked up and they all three worked fine. Now i have 2 plugged into the router - both are xppro machines - the one i am on now works with no problems. The other computer however has the limited or no connectivity problem.I used this router for years without any problems then one day this ip conflict message started to appear.
I started getting this ip conflict message on both computers but only occasionaly - it never caused any problems - if you ignored it - it would simply go away.Then one day computer #2 got the limited or no connectivity message - i simple reboot fixed it. This solution worked several times. Computer #1 has never had any problems with the internet connection.Sometime later the limited or no connectivity problem reappeared and this time a reboot did not work - i searched for a fix and decided to try changing the link speed from auto sense to 10mb half duplex - this solved the problem. This solution worked several times.
Sometime after that the limited or no connectivity reappeared and after some searching i upgraded the routers firmware - this solved the problem.Sometime later the limited or no connectivity reappeared and this time i had to actually uninstall the NIC, reboot and then let it redetect the NIC and then the problem was fixed. This solution worked several times.Sometime later (wich brings us to 3 or 4 months ago) the limited or no connectivity reappeared and this time after searching for a fix i was able to fix it by updating the NIC drivers. Problem solved.
This brings us to now - the limited or no connectivity has reappeared and none of the previous fixes correct the problem.When i originally set everything up it worked immediately out of the box.DHCP is enabled - everything is set to obtain an ip address automatically.At first the event viewer on computer #2 reported The IP address lease 192.168.1.100 for the Network Card with network address 0xxxxxxxxx has been denied by the DHCP server 192.168.1.1. {The DHCP Server sent a DHCPNACK message}.
Now the even viewer just tells me it is using ip address 169.254.xxxxxx
I have tried all of the previous fixes to no avail. I've tried shutting everything off and turning everything back on - i've tried resetting both the modem and the router - i've tried upgrading the firmware again. I even downloaded LELA and installed it on both computers thinking maybe it would detect and fix the problem buy no such luck. LELA simply tells me that computer #1 is working normally. On computer #2 when i installed LELA the first thing it did was try to find the router and it tells me it cannot find it. I tried uninstalling the NIC and removing the drivers, rebooting and then reinstalling them. No luck.
I tried setting a static ip on computer #2 with no luck. When i did these two error messages appeared in the event viewer of computer #1---
The master browser has received a server announcement from the computer (computer #2) that believes that it is the master browser for the domain on transport NetBT_Tcpip_{0876E9A8-C6E. The master browser is stopping or an election is being forced.
The name "MSHOME:1d" could not be registered on the Interface with IP address 192.168.1.100. The machine with the IP address 192.168.1.20 did not allow the name to be claimed by this machine.
If I ping the router from computer #2 it comes back 100% loss.
If I ping the NIC it comes back 0% loss.
I might also add that I can see both computer #1 and #2 in my home network workgroup on both computers. I've tried ipconfig /release and ipconfig /renew - I've tried it one after the other and also a reboot in between. I've tried clicking on repair in the LAN status - I've tried resetting the ip stack with the netsh command - I've even tried different cables and switching ports on the router.
I am going to this page: [URL] but I can see nothing regarding firmware. The "Download software" link takes me to a page that has QVPN, TFTP utilities, etc, but no firmware.