I was using Remote Desktop between two home computers hard wired through the router and a switch. Now after upgrading to firmware 1.35 I can't get remote desktop to connect. I get an error that I may not have permission, etc. I have the DIR 655 ver A and am running Windows 7 professional on both computers.
View 5 RepliesCannot connect network radios after upgrading to latest firmware. Could connect before upgrading firmware but throughput was slow for computers and streaming. Now I can connect computers, but not radios. They connect ok using Belkin and Linksys routers.
View 4 Replies View RelatedSo i'm trying to set up remote desktop connection for my desktop at (xp pro, sp2).
I've went through all the steps:
- allowed users to connect remotely (system properties)
- added to firewall exceptions
- opened up port 3389
I've disabled firewall and virus protection for now as well to test.
It works fine when I try connecting from my laptop at home by opening up the remote desktop program, and entering the local static ip address that i've configured on the desktop (i.e. 192.168.x.x);
however, when I try to connect outside of this network (on the road or office), I can't seem to connect (yes, I replaced the ip 192.168.x.x with the public ip of the desktop which I got from whatsmyip.org). I also can't ping the public ip of the desktop (can only ping the 192.168.x.x ip of the desktop)
Again, router port is open to port 3389, firewall is turned off on both the desktop and laptop, and virus protection is off.
i want to setup a remote desktop connection for 3 computers on the same network to connect to remotely. Originally i was going to port forward the original windows RDP port and run the windows rdp service but learnt that XP Home Edition doesn't support this feature. I want to be able to log onto these computers at any time remotely with the need of accessing the computer before i connect.
View 2 Replies View RelatedI have a CISCO Linksys WRT610N router on my home network which consists of the following 4 computers; Windows Small Business Server 2003, one Windows 7 Ultimate and two Windows XP Professional. How to configure a VPN on the WRT610N router that would allow me to access all of the computers on my home network over the Internet using the "Remote Desktop Connection" component.
View 2 Replies View RelatedThe other day I went to a friends house, came back home, booted up my PC, and my wireless network adapter wasn't working. I've tried everything to fix it.It's a D-Link DWA-525 802.11n Wireless PCI netowrk adapter. On device manager it just says 802.11 Wireless LAN Card with a yellow exclamation next to it. And when I check what the error is, it's either error 31 or 52 at different times, depending what I've tried to do to fix it.I tried downloading the driver for it off the D-Link website, nothing happens at all when I install it. I tried taking it out of my computer and plugging it in. I tried enabling it and disabling it on device manager.I noticed one thing, when it's in my computer the green light at the back that says activity next to it isn't on.
View 10 Replies View RelatedI currently have this router in use with verizon dsl (PPPoe) setup.I have this set to "always on". Since the verizon modem, which is also router has been set into bridge mode and the d-link came into play its been extremely slow, and dropping connection. The router is in a separate IP class, and has no conflict with the modem. My question is, if I upgrade this firmware from 1.0 to 1.02 will it default to factory settings? I know it says only some will. I do have the backup config file, but i would be doing this remotely, and would not be able to get to this router if it goes down. Has anyone gone from 1.0 to 1.2 and saw a difference and speed, and are you able to do this without losing settings.
View 3 Replies View RelatedRegion : Bulgaria
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :
ISP :
Region : Others
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : 3.13.6 Build 110923 Rel.53137n
ISP :
I bought the TL-R2543ND. The hardware version is V1.2. I want to ask, is there firmware upgrading for this version . Here I see only version V1.URL
My computer stopped being able to Remote Desktop to my server on my network. My backup software also doesn't recognize my server. But, I can access its folders using Windows Explorer. Any other PC on the network can remote desktop to the server and connect. What happened to my machine? This message appears when i try to connect: "Remote Desktop can't connect to the remote computer for one of the following reasons:
1) Remote access tot he server is not enabled
2) The remote computer is turned off
3)The remote computer is not available on the network
Make sure the remote computer is turned on and connected to the network, and that remote access is enabled."
My computer is:
AMD: Athlon 64 X2 5200+ 2991 MHz
Mobo: Gigabyte M57SLI-S4 v.2
RAM: 4GB Mushkin DDR2 PC2-6400
OS: Win 7 64bit
VC: Geforce GTX 470
Attempts to run remote desktop client a laptop on a tower using a CAT 5 Crossover isn't working. After starting the remote desktop on the laptop, I'm asked to identify the other computer, which I do, and a remote desktop window with a black background pops up, as expected. But I expect an opportunity to login will be displayed after a second or so. That never happens. After about a minute this pops up:Remote Desktop Disconnected?Your Remote Desktop session has ended.The connection to the remote computer was lost, possibly due to network connectivity problems. Try connecting to the remote computer again. If the problem continues, contact your network administrator or technical support.
My clients are impressed with my ability to setup their networks, Linksys routers with WIFI. But toss something unfamiliar into the mix, like this situation, and I'm pretty lost, pretty quick.
Environment:
Hospital's WIFI.
Laptop running XP Home with WIFI and Ethernet.
Tower running Win 7 Ultra with Ethernet.
Cat 5 crossover cable.
Goal:Configure laptop to access Hospital's WIFI. This is successful, I'm using it to post this. Configure laptop run a remote desktop with the tower as the server. The tower, running Win 7, has no monitor. I don't have a flat screen monitor, and didn't feel like dragging an 80 pound 24 inch Nokia into the hospital.After reading some sites while trying to figure this out, I gave the laptop the same group name, workgroup, as the tower.In my experience, starting the tower has been, turn it on, and it boots to Win 7. But I can't watch that happen without a monitor. I can't configure the the tower's network connections without a monitor either.I purchased the CAT 5 crossover cable yesterday, for this occasion. The label on the plastic bag it was packaged in had the word "Crossover" on it. I connect the CAT 5 to the laptop's single ethernet connection, and to the tower's Intel pro card. At home the laptop is on WIFI, the tower connects to the router.
I'm trying to use RDC to connect to my home PC from work. I've tested everything on my laptop from another network and the connection works fine but the same settings don't seem to work when I'm at work.
I'm pretty sure I have everything set up correctly. Using the default port forwarded to the desired computer.
I just upgraded from DIR 615 to DIR 655. I used the installation CD but I have no wifi signal detected. Wired connection with 655 works though. If I go back to 615, wifi works.
View 1 Replies View RelatedI have a new E1200 router. I VPN from home to my work computer just fine. since I can remotely access the router from work...what setup section of the router would I need to utilize to go backwards and access my home PC thru remote desktop? NAT? if so what are the instructions to do so.
View 1 Replies View RelatedI am upgrading my home network, I am running cat 5 cables all around my house. currently I have a comcast cable modem and a netgear router. I will have about 20 cables coming in to my office (all the network equipment is already there) I know I will need a switch but I am not sure what kind. I will be upgrading my wireless router to a much better one, should I have the router get its internet connection from the switch or have the switch get the connection from the router. Will I need a firewall? I also have a web and ftp server running behind the router? how should I connect my server?
View 4 Replies View RelatedI use RDP extensively on my LAN to use and manage 4 PCs running Win XP or Win7. My consumer-grade Cisco Linksys WRT610n crapped out after less than 2 years, so I thought I'd try the Cisco WRVS4400N to gain extra features like VPN. I have not enabled anything new on the router except for adding a second wireless SSID for guest use, although no bandwidth management or VLANs have been set up yet. Firmware version is 2.0.0.8.Since installing this router I have been unable to use Windows RDP on ANY of my computers on the LAN, whether I use the machine name or the IP address. I can ping every device on my network - print servers, NAS boxes, PCs, but no RDP. WHAT'S GOING ON?
View 6 Replies View RelatedI have been having a bit of trouble with networking my two machines to share files and allow printing i have a win 7 laptop and a xp home desktop. I share a net connection via 02 wireless box both systems have wireless i have tried many things
View 8 Replies View RelatedI have recently upgraded my router to a Belkin N750 DB and am having issues getting remote desktop connection working. Previously I had a Netgear router and it was working no problems at all.I have port forwarded (virtual server on Belkin) port 3389 TCP to the servers IP address.I can get Remote desktop connection to work when I am within my LAN by just typing the computers name.However when I try to connect via the IP address, as I would if I were away from home, then I get the message that says "remote desktop cannot connect for one of these reasons
1) remote access not enabled (it is because it worked before)
2) remote computer is turned off (no it isn't)
3) remote computer is no available" (yes it is cause can connect from LAN)
Turned off static IP for my server and let the router assign IP, and changed the IP address in the port forward, same, no connection.Double, triple checked my IP address, as this obviously changed when I plugged in the new router.Have updated to latest firmware for router and NIC.
I have a home network and I routinely connect from my laptops to my wired desktop via Remote Desktop. Routinely, that is, until I replaced my old wireless router with a D-Link Wireless N router. But now, after the change, I can no longer remote desktop in. I *am* able to ping and file share with that computer, just no remote desktop.
View 3 Replies View Relatedconfigure this router to allow connections from the internet for remote desktop? I can do it on my lan, but the Dir-825 blocks this feature. Yes, I set up port 3389 as a virtual server to the computer I wish to use.
View 6 Replies View RelatedI am attempting to set up a remote desktop connection to my home media server so I no longer need to keep a keyboard, mouse, and monitor plugged in to it when I need to use it. I am running Windows 7 Home Premium on both systems. I am sure the firewall is not the problem, as I have tried to connect with it disabled. I have also made sure to allow remote connections on the server. I know the DIR-825 supports UPnP, which works with Remote Desktop, so there should be no problem, but something is not working. I have tried disabling UPnP, setting up a virtual server, port forwarding, and assigning a permanant IP to the server, to no effect. Something is blocking my remote connection requests. Keep in mind, I am not even trying to do this over the internet, just over my LAN!
View 4 Replies View RelatedI remember the Virtual Server instead of Port Forwarding can be setup for multiple PCs to be Remote Desktop accessible from the Internet, but I forget how.
View 2 Replies View RelatedI opened the remote management to my Dir 655 but i can't enter it I tried to change port it didn't work, tried to factory defaults or hard reset didn't work what can i do I think it all so stuck my access to my remote desktop (not sure)
View 3 Replies View RelatedI recently purchased (2) DIR-655 routers; one for home and one for the office. Both are connected to the 'net through CenturyLink DSL via a Zyxel 660 modem.I am switching from a Cisco/Linksys WRT54G home and a Trendnet TEW432BRP at the office. I wanted to get up to N and consolidate to a single hardware type. The 655 came highly recommended, and the price was right at $75.My goal is to utilize RDP (Windows Remote Desktop) between the two points and from other points inbound to either 655. The first hurdle was that the Xyxel modem, by default, blocks just about everything inbound with no hope of opening the ports. The only viable solution was to bridge the modem and allow the 655 to act as DHCP. Done. The modem now should not even have its own IP address, and should completely bypass all of the built-in firewalls, etc. As soon as I went into bridged and forwarded the ports in the router we were in business (though I still can't seem to log in to RDP, the ports are verified open).
View 6 Replies View RelatedRegion : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : 1.0
ISP :
I recently bought this modem for use at home. When I try to log in to my computer at work I am able to log in to the server via a VPN connection but not onto individual computers via Remote Desktop Connection. Both computers run windows 7.
How I can use remote desktop connection to use the CD rom of the other computer in the network?
View 1 Replies View RelatedI have a user that is in a hotel with a Windows 7 laptop. He is connected to the hotel's public network and it is set as a public network in windows network and sharing center.Usually from home, which is a private network, he can log onto our VPN and then use Remote Desktop to control his work computer (which is Windows XP) here at the office; however, from this hotel, he can still connect to the VPN and access shared drives and all, but he cannot connect to any computer using remote desktop.I've tried everything, allowing remote connections for public in the firewall, even changed the network from public to private and he still cannot connect. Still, he can connect just fine from home.
View 1 Replies View RelatedI have a Dell Optiplex running XP wired to a Netgear router. My laptop is a Dell Inspiron 1501 running Windows 7. When I got the new router everything programed easily and I could retrieve files from my desktop and print remotely. Sometimes I would have to "refresh" before the laptop would detect the desktop but now it will not detect the desktop or the printer. I suspect that a Microsoft Update did this but just guessing. I went back and deleted the updates that downloaded around the time that this stopped working. I have tried every thing that I can think of to get it back working but can not get it fixed.
View 2 Replies View RelatedI have a desktop connected to internet broadband provider by a ADSL router with one extra connection to a landline phone.I have a samsung stv LA46D550 with lan port. i woulike to connect TV to the internet provide so that I can browse in TV.what extra hardware and cables do I require(with specifications).also a diagram how to connect these
my desktop has windows 7
TV LCD TV
of coursse I have connected TV to my desktop through an HDMI connector and can use TV screen as either a CLONE monitor to desktoop lor additional monitor to desktop.is this enoiugh or should I connect broadband ADSL router to TV through a router.I prefere wired connections rather wireless.
recently my network adapter just stopped working. The wifi signal was really bad so i unplugged it and when i plugged it back in it doesnt even turn on. I've reinstalled the drivers and still it doesn't turn on. In device manager there is a yellow exclamation mark next to it and when i click on properties it says code 10. I used it on my laptop and it turns on but when i plug it in my desktop it doesn't seem to turn on.
View 1 Replies View RelatedRegion : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 120320 Rel.51047n
ISP : BSNL
I am facing some issue in LAN network.I have connected one desktop( win 7) and another desktop (win xp) to the TP link router. Both the computers got ip address and able to share the internet. But both the computers are not in the same network. That is they cant PING each other. hence they are not visible to each other.
My desktop is not accessible from my laptop in my home network. This seemed to happen all of a sudden.Contact the administrator of this server to find out if you have access. PS: I can access the laptop from my desktop.
View 14 Replies View RelatedI recently moved into a new apartment, where our internet connection is shared with neighbors who are currently out of town on vacation. Most of my devices (Phone, Laptop, Girlfriend's laptop etc) will connect just fine to the passworded network we are meant to be on. My desktop however will not. It doesn't even see that it's an available wireless network.
This same computer was seeing/connecting to wireless networks as recently as this morning. It was also seeing another network for a little while with medium signal strength, which it now doesn't see either.
So far, I've restarted a couple of times, done the 'troubleshoot/repair' options on my wireless network icon, and verified that my wireless adapter is indeed on. I've also asked it to update drivers, but despite having no internet connection, it tells me it has the most current versions.
Normally, I would just reset the router as a first step, however because it's in my neighbors house, I don't have that option, however as I mentioned, this likely wouldn't make a difference, since several other devices, including the laptop I'm posting from now, are quite able to recognize and connect to the network in question.
I have a crappy router/modem from comcast with two windows machines and a linux web server connected. I also have another router, a Linksys WRT54G with DDWRT firmware with WAN connected to the modem/router. The linux web server has a static IP, configured with /etc/network/interfaces The network goes down randomly. Disconnecting and rebooting the linux web server usually fixes it. It's possible that the WRT54G could be at fault as well.The problem is that I just don't have any information on what is happening on the network. (Well even if I had the information, I'm not sure I would know what to do with it) I installed wireshark, I figure I should just leave it running until the network goes down, then I can go through the packets and see if I see anything weird?
View 4 Replies View Related