I need to reset my DLink wireless modem all over again, can't get it to recognise the router, so thought that it would need to reset to factory defaut, how can I do this. Tried just hitting reset on the router,but nothing is happening.
View 4 RepliesMy team already bought one 1800 Series router. And they setted some passwor.
Right now i am not able to login. I know the cisco password recovery method to reset the password.
Instead of password recovery method i want to try with total factory default setting.
is there is any method to do factory default without login
I have an AIR-AP521G-E-K9 and i want to reset to factory default in CLI.I tried "write erase" but dont work.I have problems with access-list and i want to desactivate access-list that i have created by web GUI.The problems now is that i can not access to my AP, no ping, no web GUI access.Access that i have is only by CLI, but access list is always blockinh all tha traffic trought my AP.How can i desactivate mac filtering, or how can i reset to factiry default
View 1 Replies View RelatedHow to reset a CAPWAP AP3600 to factory default using the AP's CLI and not the controller.
View 2 Replies View RelatedI have a WRV210-A V01 (Software: 2.0.1.5) router that when originally purchased I upgraded the firmware to the newest 2.0.1.5. However after the firmware upgrade the router has not worked right since. [I thought maybe the upgrade did not take, and successfully pushed the firmware 3x times]
Everytime you login to the webpage the right-side pane you have to scroll down 3x pages until you can see the settings options. It does that for everypage you visit you have to scroll down 3x pages until you can see the settings.
The wireless is sporadic and dropping connections, and now certain options like changing the "Basic Rate:" from "All' to "Default" does nothing and wont let you change it.
The main issue I have is that certain wireless settings like changing the "AP Isolation:" cause the router to reset back to factory defaults. and even trying to configure the LAN setup also randomly makes the router reset to factory default.
Unable to log in into our new ESW 540 switch because the default User ID and PW was changed. How do i restore the factory default on the switch.Can't get into the switch with CCA or explorer.
View 1 Replies View RelatedIm connecting to my firewall through the console port, and need to know how to reset it to factory defaults. I have looked around online and can not see any reference on how to do this.
View 11 Replies View Relatedi have a new 5505 and i have done a few configurations on it. When i try to reset it to the factory settings via asdm i get an error saying it could not be done. I have used config-factory-default using the cli option available in the asdm. I am using asa 8.2 and asdm 6.2. Will erasing the flash reset to factory defaults.
View 4 Replies View RelatedI reset unplug did everything according from cisco.com it didn't work.Can not go to 192.168.1.245. What next I need to do to make it work.
View 3 Replies View Relatedi have a wrt54gl version1.1 ok so let me start from the beginning.a few months ago i left the contry so a friend of mine asked me to lent him my router. a few day`s ago i got back and got my router back. it was working fine until i got it back. the rest button won`t work. i can`t reset the router to factory default. the user name was blank and the password was admin.now it won`t let my to do that.
View 9 Replies View RelatedDue to password loss, I get to reset the E4200 to factory default in order for router re-config.After pressing the reset buttom for 10sec, the router reset. After then, I could not access the router via browser with 192.168.1.1 at URL entry. My PC IPv4 setup: 192.168.1.11; subnet=255.255.255.0.But, ping 192.168.1.1 from PC was OK without packet loss. So router was restored with 192.168.1.1 and cable connection was OK.
View 2 Replies View RelatedI have a (old) 1231 that I would like to reuse, but no one remembers the password. how to recover a password from this model AP or how to reset the device to factory default?
View 1 Replies View RelatedI have a cisco aironet 1300 series and i need to reset it back to factory default. the directions say push the mode button while the access point is off and then turn it on while the mode button is down.
View 1 Replies View RelatedRecently purchased a RVS4000 Router, which included v1.1.14 firmware. Is it necessary to reset the router to Factory Default settings, after upgrading to v1.2.11, as in most of the other previous upgrades?
View 37 Replies View RelatedWhy when I try to reset Cisco ASA 5505 by pressing the button behind the hardware nothing happen? Just via software I can reset it?
I bought the hardware an year ago and I've never used, the problem that I don't have the blue cable and via software connecting to PC doesn't work.
I have a cisco 2960 that I seemed to have lost the password. Its just a test switch. I would like to know how to reset it to factory default. I have managed to get to a switch: prompt by holding in the small mode button on the front of the switch and pluging in the power but lost from here.
View 1 Replies View RelatedWhen I ran a reset to factory settings of my acer aspire one netbooks which runs windows 7 I no longer have a wireless connection option at all. I have done this before and never lost my ability to connect wirelessly. I tried to look for driver downloads but I'm not even sure what it is I need to do to recover the missing program as it was a original factory program.
View 4 Replies View RelatedI was trying to do a password recovery on a 1142 AP but enable password did not reset and I am stuck
AP model is AIR-AP1142N-A-K9
Running IOS c1140-k9w7-mx.124-21a.JA1
Its autonomous so there is no controller. I renamed the config.txt file I am unable to rename or delete the private-config file. I get the message that file or directory cannot be found when i try to rename and permission denied when I try to delete it.
We have an AIR-LAP1142N-E-K9 deployed in a H-REAP setup.This AP already got the configuration from the WLC when it was deployed at a remote site.Now we moved it to another site, but it doesn't appear in the WCS and i don't see any CAPWAP debug messages on the WLC.The routing work fine between the AP and the WLC, the AP also gets an IP address from DHCP and also received Option 43 information.
Now my guess was that the AP doesn't associate with the WLC because it has the old config file and it runs in local mode(without trying to connect to the WLC).We want to reset to factory defaults because we want to delete the configuration and force the AP to get a new config from the WCS.I don't know the enable password so i had to use other methods for reseting to factory defaults.
I tried to use the information from here:[URL]I used the "MODE button":I get the following message from the console:
"button pressed for 5 seconds
process_config_recovery: set IP address and config to default 10.0.0.1"
I am trying to reset my 1522 series lightweight access point to factory default.On the box,there is no any mode button.Actually password is not set to Default and need pasword recovery on this device.If you have any experience on this lightweight access point that let me know.How I reset device to fectory default.
View 1 Replies View RelatedI forgot the user for management a IPS SSM-10, when i follow the procedure to reset the password for cisco user, i can get into the module, i change the password and every thing is OK, but when i tried to configure y don´t have rights to do anything.
if i see the privileges for the user cisco this is the result. [code]
I've inherited a IAD2430 router but I don't have the ena passwords nor am I able to do a break and do a password recovery. I'm familiar with the password recovery process and config reg settings but this one has me stumped.
The config register is set to 0x2102 so I see nothing at all when it boots until it's completed and I get the prompt to "Press RETURN to get started!" I get to non priv mode but without the password obviously I'm going nowhere at that point. All the docs I've come across so far assume you can break out of the boot process or are already in rommon. When I remove the flash: I get no output at all... The IAD has no "reset" button like the CAT switches either..
I don't need the current config, just a reset/format of the NVRAM.
I wonder how i can restore my router to its defalt settings if my reset button is broken and the router has lock the mac of my pc. Can i connect the router to my pc and access it from it?
View 7 Replies View RelatedI am locked out of my Arris wtm652 (unable to login with default password or the password that i set). I have tried every way I know of to reset the modem outer to its factory settings but to no avail. I know that it is not being reset because I still can not login to it and it is maintaining the wireless security settings that were set for it.
View 1 Replies View RelatedI am the owner of an Asus N53SV series laptop running windows 7 home premium. I factory reset my PC in order to have a "fresh" new year, but now I can only connect to the wireless internet in my house using the ethernet cable. When the cable is unplugged, no networks show up for my laptop. I tried going to this link: ASUSTeK Computer Inc. -Support- Drivers and Download N53SV I downloaded the first wireless driver listed...and it gave me an error that just said "error azureware wireless lan driver"....not a very informative error.
View 13 Replies View RelatedI have been using Linksys WAG200g as a modem&router at my home for few years already and it did a great job. Plugged it on 24hours non-stop. Default firmware.
However, in the past months WAG200g did the factory reset by itself. It happened once a month, 3 months in a row already. No body pressed the reset button nor use the web admin to reset it. It reset itself. All the SSID, IP Address, passwords, etc are reset to default.
I have a DIR-655 (HW rev A2) that has worked mostly fine for a long time. Today I decided to do a firmware upgrade, and in preparation I backed up my custom config settings and did a hard reset via the factory reset button on the back of the unit.
Since then, the unit itself has been inaccessible from my computer. If I connect the DIR-655 and a PC with a network cable, the appropriate light goes on on the front of the router, but the client does not lease an IP address from the router and I can't access the router home page at 192.168.0.1.
I have tried the reset button again and also power-cycled multiple times, and I have tried connecting from multiple computers, all with the same unsuccessful results. how to "un-brick" the device?
If I use the reset on the back of the WCG200 and reset it to the original factory settings, does the firmware version revert to the original version?
View 2 Replies View RelatedWhat buttons, in specific order, do i press to reset my router? i used to know how but can no longer find that info
View 2 Replies View RelatedI had DAP-1522 setup for more than two years and working fine. I changed the default IP address from 192.168.0.50 to 10.0.0.50. Recently I replaced my older router with a new one, and now I want to reconfigure the DAP-1522 with the new router, but unable to login. I tried to factory reset but it doesn't seem to work. When I hold the reset button for 10-20 secs, I see the blue power light blinking, but it continues to blink forever. I left it for 4-5 hours and no difference yet. how to successfully reset to factory defaults so that I can access it using 192.168.0.50 IP address?
View 1 Replies View RelatedI got a ASA5505 back from a Office. I don`t know the IP Address to connect to the ASA. How can i reset the System to the Factory Settings.
View 1 Replies View RelatedWe've recently changed data line providers and now have some Cisco 877 routers we'd like to reconfigure and use at other sites. Although we own these, they were configured by our old data line providers, I'm having a hard time of resetting them to factory defaults. The simple, hold down the reset button until it restarts does not work.If I press the reset button within 5 seconds of power up to load the default rom image, I get the below:
System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE
Technical Support: [URL]
Copyright (c) 2006 by cisco Systems, Inc.
C870 series (Board ID: 1-148) platform with 131072 Kbytes of main memory
Booting flash:c870-advipservicesk9-mz.124-24.T.bin
Error opening: flash:c870-advipservicesk9-mz.124-24.T.bin
[code]....
I assume from this the required bin has either been removed, renamed or overwritten.As soon as the router boots it requires a password and I dont have the password to be able ftp files in and out of it.
i got the ACS 5.1 at work..after migrating the data from 4.1 a lot of data got changed into the 4.1 so I needed to reset my configuration (since i played around with the 5.1)after doing so, I can't access the web page, to start the configuration again tried the administrator-setup but it didn't work,
View 1 Replies View Related