Cisco Wireless :: AIR-AP1142N-A-K9 Set To Factory Default But Enable Password Not Reset
Jan 17, 2012
I was trying to do a password recovery on a 1142 AP but enable password did not reset and I am stuck
AP model is AIR-AP1142N-A-K9
Running IOS c1140-k9w7-mx.124-21a.JA1
Its autonomous so there is no controller. I renamed the config.txt file I am unable to rename or delete the private-config file. I get the message that file or directory cannot be found when i try to rename and permission denied when I try to delete it.
I have a (old) 1231 that I would like to reuse, but no one remembers the password. how to recover a password from this model AP or how to reset the device to factory default?
i have a wrt54gl version1.1 ok so let me start from the beginning.a few months ago i left the contry so a friend of mine asked me to lent him my router. a few day`s ago i got back and got my router back. it was working fine until i got it back. the rest button won`t work. i can`t reset the router to factory default. the user name was blank and the password was admin.now it won`t let my to do that.
Due to password loss, I get to reset the E4200 to factory default in order for router re-config.After pressing the reset buttom for 10sec, the router reset. After then, I could not access the router via browser with 192.168.1.1 at URL entry. My PC IPv4 setup: 192.168.1.11; subnet=255.255.255.0.But, ping 192.168.1.1 from PC was OK without packet loss. So router was restored with 192.168.1.1 and cable connection was OK.
We have an AIR-LAP1142N-E-K9 deployed in a H-REAP setup.This AP already got the configuration from the WLC when it was deployed at a remote site.Now we moved it to another site, but it doesn't appear in the WCS and i don't see any CAPWAP debug messages on the WLC.The routing work fine between the AP and the WLC, the AP also gets an IP address from DHCP and also received Option 43 information.
Now my guess was that the AP doesn't associate with the WLC because it has the old config file and it runs in local mode(without trying to connect to the WLC).We want to reset to factory defaults because we want to delete the configuration and force the AP to get a new config from the WCS.I don't know the enable password so i had to use other methods for reseting to factory defaults.
I tried to use the information from here:[URL]I used the "MODE button":I get the following message from the console:
"button pressed for 5 seconds process_config_recovery: set IP address and config to default 10.0.0.1"
I flashed the firmware and the ipv6 automatic is on disabled and I cannot set it to enabled.the 6rd tunnel option I can change but that has not effect- in fact from what I looked up it seems to be something used by some cable providers.hate to have to reset the router to factory defaults and then reset the network up - just to see if i can get the option to set IPV6 auto to enabled.
I am trying to reset my 1522 series lightweight access point to factory default.On the box,there is no any mode button.Actually password is not set to Default and need pasword recovery on this device.If you have any experience on this lightweight access point that let me know.How I reset device to fectory default.
I have an AIR-AP521G-E-K9 and i want to reset to factory default in CLI.I tried "write erase" but dont work.I have problems with access-list and i want to desactivate access-list that i have created by web GUI.The problems now is that i can not access to my AP, no ping, no web GUI access.Access that i have is only by CLI, but access list is always blockinh all tha traffic trought my AP.How can i desactivate mac filtering, or how can i reset to factiry default
I need to reset my DLink wireless modem all over again, can't get it to recognise the router, so thought that it would need to reset to factory defaut, how can I do this. Tried just hitting reset on the router,but nothing is happening.
I have a WRV210-A V01 (Software: 2.0.1.5) router that when originally purchased I upgraded the firmware to the newest 2.0.1.5. However after the firmware upgrade the router has not worked right since. [I thought maybe the upgrade did not take, and successfully pushed the firmware 3x times]
Everytime you login to the webpage the right-side pane you have to scroll down 3x pages until you can see the settings options. It does that for everypage you visit you have to scroll down 3x pages until you can see the settings.
The wireless is sporadic and dropping connections, and now certain options like changing the "Basic Rate:" from "All' to "Default" does nothing and wont let you change it.
The main issue I have is that certain wireless settings like changing the "AP Isolation:" cause the router to reset back to factory defaults. and even trying to configure the LAN setup also randomly makes the router reset to factory default.
Unable to log in into our new ESW 540 switch because the default User ID and PW was changed. How do i restore the factory default on the switch.Can't get into the switch with CCA or explorer.
Im connecting to my firewall through the console port, and need to know how to reset it to factory defaults. I have looked around online and can not see any reference on how to do this.
i have a new 5505 and i have done a few configurations on it. When i try to reset it to the factory settings via asdm i get an error saying it could not be done. I have used config-factory-default using the cli option available in the asdm. I am using asa 8.2 and asdm 6.2. Will erasing the flash reset to factory defaults.
I have a cisco aironet 1300 series and i need to reset it back to factory default. the directions say push the mode button while the access point is off and then turn it on while the mode button is down.
Recently purchased a RVS4000 Router, which included v1.1.14 firmware. Is it necessary to reset the router to Factory Default settings, after upgrading to v1.2.11, as in most of the other previous upgrades?
I have a cisco 2960 that I seemed to have lost the password. Its just a test switch. I would like to know how to reset it to factory default. I have managed to get to a switch: prompt by holding in the small mode button on the front of the switch and pluging in the power but lost from here.
When I ran a reset to factory settings of my acer aspire one netbooks which runs windows 7 I no longer have a wireless connection option at all. I have done this before and never lost my ability to connect wirelessly. I tried to look for driver downloads but I'm not even sure what it is I need to do to recover the missing program as it was a original factory program.
I have a cisco PIX-515e which i have connected to a emulator through the console port, and im having trouble erasing data from it. I can get into 'pixfirewall' mode and 'monitor' mode but thats as far as i get. i have tried 'write erase' and 'configure factory-default' in both modes to no success.
I recently decomissioned an 871 from a small business site and the owner did not want the device anymore. So now I'm trying to use it back at the office in the sandbox, however I don't know the password to the device and neither does the business owner. There's a reset button on the back, but from what I've read (here), it only loads a different config file found on the internal flash. Tried this, no dice. Is this essentially a bricked router now or is there anything else I can do to clear the config and repurpose it for my use?
I need to recover the passwords for my 3750 stack (2 switches), I have the password recovery documentation but it seems to be referring to recovery for one switch. How do I go about recovery when in a stack, should I remove the links on the switches and recover each one separately?Alternatively can I do a factory reset on them
Last year our Network Security Supervisor submit his resignation and unfortunately did not endorse us the admin password we already tried the password he suggested when we contacted him but nothing of them works. Is there anyway we can reset the password without resetting to factory default?
Im trying to access the switch to reset the password to factory defaults (please see switch output Astrix has removed customer identifying information for security purposes.) Each time I reboot the switch and try and access the password recover mode this same output below starts and im still not able to access the recovery area of the switch
cisco WS-C3560G-48PS (PowerPC405) processor (revision F0) with 122880K/8184K bytes of memory.
Processor board ID FOC1133Y28Q Last reset from power-on 1 Virtual Ethernet interface 52 Gigabit Ethernet interfaces The password-recovery mechanism is enabled.
We are installaing a new RSP720 on 7606 platform and facing a peculiar problem. It is prompting for a enable password. We have not configured anything on router yet, still it is asking for enable password.
I am the owner of an Asus N53SV series laptop running windows 7 home premium. I factory reset my PC in order to have a "fresh" new year, but now I can only connect to the wireless internet in my house using the ethernet cable. When the cable is unplugged, no networks show up for my laptop. I tried going to this link: ASUSTeK Computer Inc. -Support- Drivers and Download N53SV I downloaded the first wireless driver listed...and it gave me an error that just said "error azureware wireless lan driver"....not a very informative error.
Is there any possible way to factory reset an AIR-AP1231G-A-K9 that was once attached to a WLC via SSH? I dont have physical access to it and the old WLC has long been decommissioned. I have tried the clear command but since it is in CAPWAP mode that command has been disabled. I know I can press and hold the mode button and reset it that way but I need to know if its possible through SSH to be reset. I have two that are in need of being reset in order to connect to the new WLC.
Any info on successfully resetting an light weight 1130 AP to the factory settings? I tried the method described in the doc for 1130 on how to reset 1130 AP to the default settings, but it was not successful. I tried shutdown the AP, and plug in the power while press and holding the Mode button for about 3 seconds.This AP has lost it association with the WLC, is there anyway i can reset the AP to factory default and put in the correct IP address again?