Cisco Switching/Routing :: How To Reset 2960 To Factory Default

May 31, 2012

I have a cisco 2960 that I seemed to have lost the password. Its just a test switch. I would like to know how to reset it to factory default. I have managed to get to a switch: prompt by holding in the small mode button on the front of the switch and pluging in the power but lost from here.

View 1 Replies


ADVERTISEMENT

Cisco WAN :: 1800 - Factory Default Reset?

Sep 24, 2012

My team already bought one 1800 Series router. And they setted some passwor.
 
Right now i am not able to login. I know the cisco password recovery method to reset the password.
 
Instead of password recovery method i want to try with total factory default setting.
 
is there is any method to do factory default without login

View 5 Replies View Related

Cisco WAN :: AIR-AP521G-E-K9 / Reset To Factory Default In CLI

Jan 22, 2012

I have an AIR-AP521G-E-K9 and i want to reset to factory default in CLI.I tried "write erase" but dont work.I have problems with access-list and i want to desactivate access-list that i have created by web GUI.The problems now is that i can not access to my AP, no ping, no web GUI access.Access that i have is only by CLI, but access list is always blockinh all tha traffic trought my AP.How can i desactivate mac filtering, or how can i reset to factiry default

View 1 Replies View Related

Reset DLink Modem To Factory Default?

Jan 2, 2013

I need to reset my DLink wireless modem all over again, can't get it to recognise the router, so thought that it would need to reset to factory defaut, how can I do this. Tried just hitting reset on the router,but nothing is happening.

View 4 Replies View Related

Cisco Wireless :: Factory-Default Reset For AP3600?

Dec 17, 2012

How to reset a CAPWAP AP3600 to factory default using the AP's CLI and not the controller.

View 2 Replies View Related

Cisco Routers :: WRV210-A V01 Reset To Factory Default?

Oct 30, 2011

I have a WRV210-A V01 (Software: 2.0.1.5) router that when originally purchased I upgraded the firmware to the newest 2.0.1.5. However after the firmware upgrade the router has not worked right since. [I thought maybe the upgrade did not take, and successfully pushed the firmware 3x times]
 
Everytime you login to the webpage the right-side pane you have to scroll down 3x pages until you can see the settings options. It does that for everypage you visit you have to scroll down 3x pages until you can see the settings.
 
The wireless is sporadic and dropping connections, and now certain options like changing the "Basic Rate:" from "All' to "Default" does nothing and wont let you change it.
 
The main issue I have is that certain wireless settings like changing the "AP Isolation:" cause the router to reset back to factory defaults. and even trying to configure the LAN setup also randomly makes the router reset to factory default.

View 1 Replies View Related

Cisco Switches :: ESW 540 / How To Reset Switch To Factory Default

Jun 1, 2011

Unable to log in into our new ESW 540 switch because the default User ID and PW was changed.  How do i restore the factory default on the switch.Can't get into the switch with CCA or explorer.

View 1 Replies View Related

Cisco Firewall :: PIX 515E Reset To Factory Default?

Jul 3, 2011

Im connecting to my firewall through the console port, and need to know how to reset it to factory defaults. I have looked around online and can not see any reference on how to do this.

View 11 Replies View Related

Cisco Firewall :: Cannot Reset 5505 To Factory Default

Apr 10, 2011

i have a new 5505 and i have done a few configurations on it. When i try to reset it to the factory settings via asdm i get an error saying it could not be done. I have used config-factory-default using the cli option available in the asdm. I am using asa 8.2 and asdm 6.2. Will erasing the flash reset to factory defaults.

View 4 Replies View Related

Cisco Wireless :: Reset Aironet 1231 To Factory Default?

Sep 17, 2012

I have a (old) 1231 that I would like to reuse, but no one remembers the password.  how to recover a password from this model AP or how to reset the device to factory default?

View 1 Replies View Related

Cisco :: Aironet 1300 Series Reset To Factory Default

Aug 16, 2011

I have a cisco aironet 1300 series and i need to reset it back to factory default.  the directions say push the mode button while the access point is off and then turn it on while the mode button is down.

View 1 Replies View Related

Cisco Routers :: RVS4000 Necessary To Reset To Factory Default Settings

Feb 15, 2009

Recently purchased a RVS4000 Router, which included v1.1.14 firmware. Is it necessary to reset the router to Factory Default settings, after upgrading to v1.2.11, as in most of the other previous upgrades?

View 37 Replies View Related

Cisco Firewall :: ASA 5505 Doesn't Reset To Factory Default?

Jun 20, 2011

Why when I try to reset Cisco ASA 5505 by pressing  the button behind the hardware nothing happen? Just via software I can reset it?
 
I bought the hardware an year ago and I've never used, the problem that I don't have the blue cable and via software connecting to PC doesn't work.

View 6 Replies View Related

Linksys Access Point :: Wap54g / How To Reset To Factory Default

Jan 24, 2013

I reset unplug did everything according from cisco.com it didn't work.Can not go to 192.168.1.245. What next I need to do to make it work.

View 3 Replies View Related

Linksys Wireless Router :: Wrt54gl Won't Reset To Factory Default

Jul 25, 2012

i have a wrt54gl version1.1 ok so let me start from the beginning.a few months ago i left the contry so a friend of mine asked me to lent him my router. a few day`s ago i got back and got my router back. it was working fine until i got it back. the rest button won`t work. i can`t reset the router to factory default. the user name was blank and the password was admin.now it won`t let my to do that.

View 9 Replies View Related

Linksys Wireless Router :: E4200 Reset To Factory Default

Nov 26, 2012

Due to password loss, I get to reset the E4200 to factory default in order for router re-config.After pressing the reset buttom for 10sec, the router reset.  After then, I could not access the router via browser with 192.168.1.1 at URL entry.  My PC IPv4 setup: 192.168.1.11; subnet=255.255.255.0.But, ping 192.168.1.1 from PC was OK without packet loss.  So router was restored with 192.168.1.1 and cable connection was OK.

View 2 Replies View Related

Cisco Wireless :: AIR-AP1142N-A-K9 Set To Factory Default But Enable Password Not Reset

Jan 17, 2012

I was trying to  do a password recovery on a 1142 AP  but  enable password did not reset  and I am stuck 
 
AP model is   AIR-AP1142N-A-K9
Running IOS  c1140-k9w7-mx.124-21a.JA1
 
Its autonomous so there is no controller.  I renamed the config.txt file I am unable to rename or delete the  private-config file. I get the message that file or directory cannot be found when i try to rename and permission denied when I try to  delete it.

View 12 Replies View Related

Lost Wifi When Ran Factory Default Reset On Acer Aspire One Netbook

May 21, 2012

When I ran a reset to factory settings of my acer aspire one netbooks which runs windows 7 I no longer have a wireless connection option at all. I have done this before and never lost my ability to connect wirelessly. I tried to look for driver downloads but I'm not even sure what it is I need to do to recover the missing program as it was a original factory program.

View 4 Replies View Related

Cisco Switching/Routing :: Can't Factory Reset CE500

Nov 27, 2011

I am trying to factory reset CE500 switch, as described in the factory rest section of the documentation. I do not get an IP address via DHCP from the switch.
 
On boot up I hold the setup button down, wait till the lights go solid amber release setup. wait for a port on the switch to start blinking green port 1 starts blinking green, plug my pc into port and wait for IP..and keep waiting !!!!
 
I have tried this on 3 switches now all with the same result.... NO IP offered.

View 1 Replies View Related

Cisco Switching/Routing :: 871 Factory Reset Without Password?

Jan 24, 2012

I recently decomissioned an 871 from a small business site and the owner did not want the device anymore. So now I'm trying to use it back at the office in the sandbox, however I don't know the password to the device and neither does the business owner.  There's a reset button on the back, but from what I've read (here), it only loads a different config file found on the internal flash. Tried this, no dice. Is this essentially a bricked router now or is there anything else I can do to clear the config and repurpose it for my use?

View 7 Replies View Related

Cisco Wireless :: AIR-LAP1142N-E-K9 / Reset To Factory Default Doesn't Work On 1142 AP

Jul 5, 2010

We have an AIR-LAP1142N-E-K9  deployed in a H-REAP setup.This AP already got the configuration from the WLC when it was deployed at a remote site.Now we moved it to another site, but it doesn't appear in the WCS and i don't see any CAPWAP debug messages on the WLC.The routing work fine between the AP and the WLC, the AP also gets an IP address from DHCP and also received Option 43 information.
 
Now my guess was that the AP doesn't associate with the WLC because it has the old config file and it runs in local mode(without trying to connect to the WLC).We want to reset to factory defaults because we want to delete the configuration and force the AP to get a new config from the WCS.I don't know the enable password so i had to use other methods for reseting to factory defaults.
 
I tried to use the information from here:[URL]I used the "MODE button":I get the following message from the console:

"button pressed for 5 seconds
process_config_recovery: set IP address and config to default 10.0.0.1"

View 24 Replies View Related

Cisco Switching/Routing :: 3750G Won't Factory Default?

Jun 2, 2013

I have a 3750G that used to be a Stack Master of a stack comprised of 2 identical switches. Since then, we have removed the stack from production, and I factory defaulted the stack MEMBER and that went fine. I just held the "Mode" button on the front until the lights all lit up and then issued the reload command and the switch came back with no configuration OTHER than the vlan database I issued the "del vlan.dat" command to no avail. I just manually removed all the vlans.
 
The stack MASTER on the other hand will NOT go back to factory defaults, and will also NOT erase the vlan database. Everything I try will NOT work. I've tried the following
 
1) Hold mode button & issue a reload after the lights start flashing

2) issue "Write Erase" then issue "reload"

3) issue "Write Erase", then issue "Write", then issue "reload"

4) issue "erase start" then issue "reload" (just in case the "write erase" command is being depriciated or something weird)

5) issue "erase start" then issue "copy run start" then issue "reload"
 
Is there a special way to reset a StackMaster back to factory defaults?

View 6 Replies View Related

Cisco Switching/Routing :: Catalyst Express 500 Factory Reset

Sep 30, 2009

We have inherited a Catalyst Express 500 (model WS-CE500-24PC) from a company we aquired, and are having issues configuring the switch.
 
The switch must have been configured previously, but we don't know its IP address.  It is no longer on the network, so we can restart it as much as we need to.
 
We followed the factory reset process:
 
1)  Disconnect the switch from the power supply
2)  Reconnect the switch while holding the "SETUP" button
3)  Release the "SETUP" button when the status LEDs all turn Amber
4)  Wait for POST to complete
5)  Connect one PC to the port whose LED starts flashing
 
However, the PC is never given an IP address, and when we open a web browser, anything we try to browse to gives us "Page cannot be displayed", rather than the setup page for the switch.
 
Are there any known issues or browser/OS incompatibilities with this model of switch?  We're using Vista and Windows 7 with IE7, IE8 and Firefox 3.

View 9 Replies View Related

Cisco Switching/Routing :: Reset 800 Back To Factory Defaults?

Jan 16, 2012

I have a cisco 800 that needs to be reset back to factory defaults. I tried typing in "config factory-default 10.10.10.1 255.255.255.0" at the conf t prompt, but I got an error Invaild input detected at ^ (the ^ is just under the word factory). So after a bit of reserch I came across this command "write erase" that seemed to do something but now I can't get any ip addreses. Here is the running config:
 
Using 1104 out of 131072 bytes
!
version 12.4
service config

[Code].....

View 13 Replies View Related

Cisco Switching/Routing :: 4507 R-E With Sup 10GE Factory Reset

Jul 29, 2012

I have been trying to reset my Cisco 4507 R-E with sup 10GE engines, and I am not having any luck. I have followed the following document:
 
[URL]
 
I have tried "wr erase" and "erase startup-config." I cannot delete the vlan.dat file either. I am using the command "erase cat4000_flash:vlan.dat" and its not working either. I have done these commands several times with no success. When asked if I want to save the config changes, I am answering with a "no" I have not tried to depress the small "reset" button on the front of the sup engines as I read that this just restarts the switch.

View 2 Replies View Related

Cisco Switching/Routing :: Reset 2911 ISR To Factory Defaults

Feb 7, 2012

I reset my Cisco 2911 ISR to the factory defaults.  I then used the configuration guide to do the initial set-up through the CLI.  I was able to assign IPs to the GE0/0 and GE0/1 ports.  Now I cannot access the GUI device manager at all.  I was able to ping the IP of GE0/0 so I know the adapter took the IP assignment, but still no GUI access.

View 7 Replies View Related

Cisco Wireless :: Reset 1522 Series Lightweight Access Point To Factory Default?

Jan 13, 2013

I am trying to reset my 1522 series lightweight access point to factory default.On the box,there is no any mode button.Actually password is not set to Default and need pasword recovery on this device.If you have any experience on this lightweight access point that let me know.How I reset device to fectory default.

View 1 Replies View Related

Cisco Switching/Routing :: Factory Reset Catalyst WS-C2960G-8TC-L Switch?

Feb 20, 2012

How do I do a factory reset on a Cisco Catalyst WS-C2960G-8TC-L switch?

View 2 Replies View Related

Cisco Switching/Routing :: Catalyst 3560 - Access Switch To Reset Password To Factory Defaults

Nov 5, 2012

Im trying to access the switch to reset the password to factory defaults (please see switch output Astrix has removed customer identifying information for security purposes.) Each time I reboot the switch and try and access the password recover mode this same output below starts and im still not able to access the recovery area of the switch
 
cisco WS-C3560G-48PS (PowerPC405) processor (revision F0) with 122880K/8184K bytes of memory.

Processor board ID FOC1133Y28Q
Last reset from power-on
1 Virtual Ethernet interface
52 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.

[code]....

View 1 Replies View Related

Cisco Switching/Routing :: 2960 Default Gateway Ip Route

Jan 24, 2013

I have a Cisco 2960 ( WS-C2960-8TC-S)  running 12.2(46)SE  C2960-LANLITEK9-M  image.I would like to set an ip route 0.0.0.0 0.0.0.0 87.101.156.97  but the current image does not allow.Will ip default-gateway 87.101.156.97 work or do I need ip routing ?The ISP has provided a /30 address and we are using an additional /29 for our network devices.  I dont think this image can be upgraded.  I need to forward routes directly out to ISP. [code]

View 5 Replies View Related

Cisco Switching/Routing :: Default Password For 2960-C Layer 3 Switch

Dec 23, 2012

I just received a Catalyst 2960-C (WS-C2960C-8TC-L R) switch and I am unable to sign into its web GUI in order to configure it. I've tried both the Cisco Network Assistant and Internet Explorer and I am unable to log in either way. The documentation provided by Cisco states that the default password is simply cisco and that a username is unnecessary. Needless to say, it doesn't work. I've also Googled for other default passwords (such as cisco-cisco as the username-password), none of which worked either. I've also tried resetting the switch back to its factory default a few times.

View 8 Replies View Related

Cisco Switching/Routing :: 2960 - Difference Between SDM Prefer Access And Default

Aug 22, 2012

What is the difference between  sdm prefer access & sdm prefer default & sdm prefer lanbase-routing? When do we use these options?

View 2 Replies View Related

Cisco Switching/Routing :: 4500 / 2960 - How Layer 2 Switch Works Without Default Gateway

Aug 14, 2012

4500 switch is connected to 2960 switch.
 
4500  config
Vlan 10
name Data
 
It has ip helper configured that points to DHCP.From 4500  switch port  - port  x connects to 2960 port.Port x is configured as trunk between 4500 and 2960.

2960 config
vlan 10  
name data 

All user ports are configured under vlan 10 and as access ports.Port x is trunk port connected frpm 2960  to 4500 switch allowing vlan 1 and 10 only.This switch has no default gateway configured.
 
We connected user PC on 2960 switchports and they were able to get the IP from DHCP server and were able to access the network? My question is how users on 2960 switch are able to access the network without ip default-gateway configured  on 2960 switch?

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved