Cisco Switching/Routing :: 4507 R-E With Sup 10GE Factory Reset
Jul 29, 2012
I have been trying to reset my Cisco 4507 R-E with sup 10GE engines, and I am not having any luck. I have followed the following document:
[URL]
I have tried "wr erase" and "erase startup-config." I cannot delete the vlan.dat file either. I am using the command "erase cat4000_flash:vlan.dat" and its not working either. I have done these commands several times with no success. When asked if I want to save the config changes, I am answering with a "no" I have not tried to depress the small "reset" button on the front of the sup engines as I read that this just restarts the switch.
View 2 Replies
ADVERTISEMENT
Nov 27, 2011
I am trying to factory reset CE500 switch, as described in the factory rest section of the documentation. I do not get an IP address via DHCP from the switch.
On boot up I hold the setup button down, wait till the lights go solid amber release setup. wait for a port on the switch to start blinking green port 1 starts blinking green, plug my pc into port and wait for IP..and keep waiting !!!!
I have tried this on 3 switches now all with the same result.... NO IP offered.
View 1 Replies
View Related
Jan 24, 2012
I recently decomissioned an 871 from a small business site and the owner did not want the device anymore. So now I'm trying to use it back at the office in the sandbox, however I don't know the password to the device and neither does the business owner. There's a reset button on the back, but from what I've read (here), it only loads a different config file found on the internal flash. Tried this, no dice. Is this essentially a bricked router now or is there anything else I can do to clear the config and repurpose it for my use?
View 7 Replies
View Related
Sep 30, 2009
We have inherited a Catalyst Express 500 (model WS-CE500-24PC) from a company we aquired, and are having issues configuring the switch.
The switch must have been configured previously, but we don't know its IP address. It is no longer on the network, so we can restart it as much as we need to.
We followed the factory reset process:
1) Disconnect the switch from the power supply
2) Reconnect the switch while holding the "SETUP" button
3) Release the "SETUP" button when the status LEDs all turn Amber
4) Wait for POST to complete
5) Connect one PC to the port whose LED starts flashing
However, the PC is never given an IP address, and when we open a web browser, anything we try to browse to gives us "Page cannot be displayed", rather than the setup page for the switch.
Are there any known issues or browser/OS incompatibilities with this model of switch? We're using Vista and Windows 7 with IE7, IE8 and Firefox 3.
View 9 Replies
View Related
Jan 16, 2012
I have a cisco 800 that needs to be reset back to factory defaults. I tried typing in "config factory-default 10.10.10.1 255.255.255.0" at the conf t prompt, but I got an error Invaild input detected at ^ (the ^ is just under the word factory). So after a bit of reserch I came across this command "write erase" that seemed to do something but now I can't get any ip addreses. Here is the running config:
Using 1104 out of 131072 bytes
!
version 12.4
service config
[Code].....
View 13 Replies
View Related
Feb 7, 2012
I reset my Cisco 2911 ISR to the factory defaults. I then used the configuration guide to do the initial set-up through the CLI. I was able to assign IPs to the GE0/0 and GE0/1 ports. Now I cannot access the GUI device manager at all. I was able to ping the IP of GE0/0 so I know the adapter took the IP assignment, but still no GUI access.
View 7 Replies
View Related
May 31, 2012
I have a cisco 2960 that I seemed to have lost the password. Its just a test switch. I would like to know how to reset it to factory default. I have managed to get to a switch: prompt by holding in the small mode button on the front of the switch and pluging in the power but lost from here.
View 1 Replies
View Related
Feb 20, 2012
How do I do a factory reset on a Cisco Catalyst WS-C2960G-8TC-L switch?
View 2 Replies
View Related
Nov 5, 2012
Im trying to access the switch to reset the password to factory defaults (please see switch output Astrix has removed customer identifying information for security purposes.) Each time I reboot the switch and try and access the password recover mode this same output below starts and im still not able to access the recovery area of the switch
cisco WS-C3560G-48PS (PowerPC405) processor (revision F0) with 122880K/8184K bytes of memory.
Processor board ID FOC1133Y28Q
Last reset from power-on
1 Virtual Ethernet interface
52 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
[code]....
View 1 Replies
View Related
Nov 17, 2011
How to confirm if a 10Ge interface can be set down to 1Ge if required ?
View 4 Replies
View Related
Jun 5, 2013
We had to transport one of our 4948 10 GE to another Data Centre and when we got it there and tried to power up its System Status LED was red and we cannot even get console to the device.
We can try to see if the switch is completely dead and needs replacing or is there something we can do to get it back up and running again?
View 1 Replies
View Related
Nov 18, 2012
I am in front of a choice what to select to deploy 10Ge in my datacenter to get four 6504e and two 3750x units connected to each other.All devices are located in 3-7 meters away from each other.The choice is whether to go for a multimode fiber and 10GBASE-SR X2 Modules OR cat7 UTP and 10GBASE-T X2 pluggable transceiver.Money wise it doesn't matter.Fiber looks less attractive since it's fragile and a bit harder to put in underfloor area.Cat7 is more attractive but there are 2 points:
1) I couldn't find ANY single photo of a 10GBASE-T (a module with a single RJ45 port). How does it look? Does it come with a cable or...??
2) How stable is it to run 10Ge over UTP?
View 1 Replies
View Related
Jan 28, 2013
I have a two Cisco 4510R each with two sup V-10GE redundant. The code on these sup modules are 12.2(31r)SG3. I need some assistance in getting this setup worked out. I have all four of the 10GE populated with appropriate optics. I setup a link from one 4510R to the other using these interfaces. From the documentation I found I had to use Tengi1/1 and Tengi2/2 as the redundant pair. I plugged the up link into these ports. The Tengi1/1 (active supervisor) links up and works fine. But when I look at the ports port Tengi2/2 it isn't showing link or active. Now port 2/1 (nothing plugged into it) is showing as active.
Now is the redundancy supposed to be 1/1 and 2/1? If so, the switch is in production, when I move the connection over from 2/2 to 2/1 will it cause a outage? The reason for this is I now have a system with a 10G port and would like to utilize one of the other 10G ports. Is that possible? Or does it have to be a lag/redundant up link to work (say to another switch)?
View 2 Replies
View Related
May 6, 2013
We have a scenario with 2 chassis, both with 2 supervisor Engine 2T, we try to make a configuration of VSS with the chassis and would link to know if is possible have 2 supervisor on chassis one and 2 supervisors on chassis 2 with VSS?
Router#sho switch virtual redundancy
My Switch Id = 1
Peer Switch Id = 2
Last switchover reason = active unit removed
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
[code]....
would like to use the second supervisors for obteind the local redundancy en chassis 1 and 2, this is possible?
the actually version on four supervisors is: s2t54-ipservicesk9-mz.SPA.150-1.SY3.bin
View 6 Replies
View Related
Jun 17, 2012
What does RP drops entail? We are experiencing 0.23 % drops on an vlan int on one of our 6500. This interface is an L3 to a server-subnet. Doing a sh int vlan 238 switching shows 30935411 RP (Route Processing) drops.It was a bit unclear to me in the thread "Input queue drops on 6500 vlan interface" if RP drops was through the router, or to the router(mgmnt)?I can do a netdr to see what traffic goes to it. It should not generate CPU load, but I think I will wait until after hours before I try that command.
- do NETDR:
-- debug netdr cap rx vlan 238
-- show netdr cap
View 5 Replies
View Related
Jan 22, 2013
We have two 3750 stackable switches in core layer.
1. We are planning to stack two 3750 for greater bandwidth to use
2. We could configure 10GE link (by Network module) between these two switches
which solution provides increased bandwidth and redundancy?
View 5 Replies
View Related
Feb 7, 2013
I am trying to configure a 6509 as the passive receiver from a Dell Force10 10Ge switch with 2 sfp to 2 gig ports on our 6509 switch, I see LACP is up on both sides but cannot pass traffic, I have only 2 vlans that will carry across the aggregate link from our vmware boxes, this is just a temp until I get a 10ge in our 6509 chassis.
View 2 Replies
View Related
Jun 4, 2012
I am getting conflicting info about this, and need to get confirmations.Is the older 6513 (non E) model compatible with WS-X6407-10GE blade?The switch we're getting this for have WS-SUP720-3B, 6000W power supply, and WS-C6K-13SLT-FAN2.From what I read they are compatible if entered in slot 9-13, but I also heard that 10GE modules are not compatible with the non E chassis.
View 1 Replies
View Related
Feb 27, 2013
I am looking for 10 GE copper 24 ports switch. After any time I come N2K-C2232TM-10GE. However, this switch is fabric extender and it is used with Nexus 5K series switches.
My question is Can I use this Nexus 2K standalone as other L2 switches?
View 4 Replies
View Related
Sep 23, 2012
We have CORE switch model : Cisco WS-C4510R-E with dual SUP 5 - 2 10GE. [code] Now We want to upgrade this IOS to the upgraded version.
View 3 Replies
View Related
Sep 8, 2011
I will be adding two WS-X6716-10GE cards in a CAT6509 soon, and will create 4 port channels with 3 ports each in the new cards, but I do have a few questions:
1 - I will be adding cards in slots 3 and 8, can I mix and bundle ports from both modules into a single etherchannel, I mean, like two ports in slot 3 and 1 port in slot 8 to create a PortChannel ?! Or can I only bundle ports in the same card/port-group in a Etherchannel using this WS-X6716-10GE card?
2 - Do I need to issue the hw-module slot x oversubscription port-group y command in order to be able to bundle ports in the Etherchannel I need to create ?! I will be using 4 Etherchannels (LACP) with 3 ports each, running in trunk mode. So I guess, I will be using something like:
int tengig 3/1
switchport mode trunk
switchport trunk encapsulation dot1q
logging event link-status
[Code] ....
View 4 Replies
View Related
Dec 4, 2011
Is it possible that catalyst 4500 Supervisor Engine V-10GE WS-X4516-10GE works with WS-X4612-SFP-E?I know suprtvisor engine V-10GE is not support E-serious linecard, but when I use the configuration tool, I can choose these two products together. Is it a bug?I need novell IPX in this case, I find supervisor 6E & 7E are already not support, so I have no choice to choose V-10GE.
View 1 Replies
View Related
Aug 3, 2011
I am trying to setup the management vrf on the 4948 10GE so that my TACACS requests will use that vrf for out-of-band purposes. The vrf is working properly because I can ping the TACACS server using the vrf but the logins do not work. I see this error in the tacacs debug:
TPLUS(00000016)/0: Connect Error No route to host
Looking at the release notes, it states that my version (12.2.54 SG1) does support vrf aware tacacs but the documentation seems to be a bit off because i do not get a server private command option as stated in the configuration doc after configuring a tacacs server group:
[URL]
Here is my config:
ip vrf mgmtVrf
rd X:X
!
interface FastEthernet1
ip vrf forwarding mgmtVrf
ip address x.x.x.x
[code]....
View 7 Replies
View Related
Dec 10, 2012
Does any know what " Last reset from system-reset " means? Is this becouse of a power failure or someone reloading the switch?
View 3 Replies
View Related
Jan 17, 2012
When i swapped a Sup v 10 ge for a Sup6 E Tonight in order to take advantage of the netflow capabilites of the Sup V - It came up with module unsupported for the following cards - WS-X4648-RJ45V-E Will these only work with the Sup6 E or what
View 2 Replies
View Related
Oct 25, 2011
ive updated my catalyst 4948-10GE to version 15.0(2)SG1.Now it is not possible to login by ssh or telnet on this switch. the access is established over the mgmt-Interface and vrf.i get a ping reply but login is no more possible now.is there an new feature in this version for vrf or remotelogin that has to be configured? if neccessary i can paste the running-config here.
View 3 Replies
View Related
Sep 11, 2011
just want to confirm if I could use the 2x 10GE uplink ports of a cisco 2960 to connect to my Server directly?
View 17 Replies
View Related
Jun 6, 2011
I want to choose a pair of switches for our data center.What I need: 48 x 1GE access ports, 2 x 10GE uplink ports.Nice feature of 3750-X is stacking. So what features has 4948-10GE? Why I should prefer that switch?
View 11 Replies
View Related
May 2, 2012
Connected server on a tenGigabitEthernet interface simple configuration setup
switchport
switchport access vlan 201
end
for server connection. Connected with Fibre. The interface is up and up but cannot ping server?
View 10 Replies
View Related
Feb 25, 2013
I forgot the user for management a IPS SSM-10, when i follow the procedure to reset the password for cisco user, i can get into the module, i change the password and every thing is OK, but when i tried to configure y don´t have rights to do anything.
if i see the privileges for the user cisco this is the result. [code]
View 4 Replies
View Related
Aug 18, 2011
I've inherited a IAD2430 router but I don't have the ena passwords nor am I able to do a break and do a password recovery. I'm familiar with the password recovery process and config reg settings but this one has me stumped.
The config register is set to 0x2102 so I see nothing at all when it boots until it's completed and I get the prompt to "Press RETURN to get started!" I get to non priv mode but without the password obviously I'm going nowhere at that point. All the docs I've come across so far assume you can break out of the boot process or are already in rommon. When I remove the flash: I get no output at all... The IAD has no "reset" button like the CAT switches either..
I don't need the current config, just a reset/format of the NVRAM.
View 2 Replies
View Related
May 15, 2012
we have Supervisor Engine 720 10GE (VS-S720-10G) in slot 5 on Catalyst 6509-E. Slot 6 is free. We need to replace VS-S720-10G. Is it possible the following scenario
1. we will insert new VS-S720-10G into the slot 6
2. then we will remove the faulty VS-S720-10G from the slot 5
Will everything work without interuptions. Is any document where I can find step-by-step procedure how to replace VS-S720-10G ?
View 3 Replies
View Related
Jan 17, 2012
Is it possible to use a 10GE interface on a sup720 and an interface from a 671610GE line card and create a port channel. I haven't found specific documentation on CCO stating you can. I have found the QOS queuing is differnet between the sup and line card.
View 1 Replies
View Related
