Cisco Switching/Routing :: 4510R-E With Dual SUP V / 10GE IOS Upgradation
Sep 23, 2012We have CORE switch model : Cisco WS-C4510R-E with dual SUP 5 - 2 10GE. [code] Now We want to upgrade this IOS to the upgraded version.
View 3 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 4510R - SUP V-10GE Uplink
Jan 28, 2013I have a two Cisco 4510R each with two sup V-10GE redundant. The code on these sup modules are 12.2(31r)SG3. I need some assistance in getting this setup worked out. I have all four of the 10GE populated with appropriate optics. I setup a link from one 4510R to the other using these interfaces. From the documentation I found I had to use Tengi1/1 and Tengi2/2 as the redundant pair. I plugged the up link into these ports. The Tengi1/1 (active supervisor) links up and works fine. But when I look at the ports port Tengi2/2 it isn't showing link or active. Now port 2/1 (nothing plugged into it) is showing as active.
Now is the redundancy supposed to be 1/1 and 2/1? If so, the switch is in production, when I move the connection over from 2/2 to 2/1 will it cause a outage? The reason for this is I now have a system with a 10G port and would like to utilize one of the other 10G ports. Is that possible? Or does it have to be a lag/redundant up link to work (say to another switch)?
Cisco Switching/Routing :: High CPU Utilization On 4510R Switch With Dual SUP V -10G
Feb 14, 2012We have a problem of igh CPU Utilization in Cisco 4510R-with dual SUP V-10G modules.
Cisco 4510R switch is the CORE switch and have 30 no's of VLans. It was running PVST/PVST+ previously. But Now we have migrated to MST. But after upgradation the CPU utilization reached alomst 98%.
Cisco Switching/Routing :: 4510R+E - Dual Sup 7e Software / ROMmon Upgrade?
Jun 1, 2011We have some 4510R+E with dual sup 7e that have experienced problems recently. One of the sup 7e's crashed with a "critical software exception":
#show verCisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.01.01.SG RELEASE SOFTWARE (fc1)
<snip>
ROM: 15.0(1r)SG1
<snip> Last reload reason: Critical software exception, check bootflash:crashinfo_iosd
So I thought I'd upgrade to IOS-XE 3.2.0SG to hopefully resolve the issue. I was reading the software release notes and it says:
If you are upgrading to 3.2.0SG, you must upgrade your ROMMON to 15.0(1r)SG2.If they have dual supervisors, first upgrade your software to 3.2.0SG, then upgrade your ROMMON to15.0(1r)SG2 to avoid the resets uplinks issue (CSCtj54375).
And from the ROMMON release notes it says:
Download the cat4500+e-promupgrade-150_1r_SG2 program from Cisco.com, and place it on a TFTPserver in a directory that is accessible from the switch that is upgraded.The cat4500+e-promupgrade-150_1r_SG2 program is available on Cisco.com at the same location from which Catalyst 4500 system images are downloaded.
So I have several questions:
The only promupgrade file I can find is cat4500-e-ios-promupgrade-150-1r-SG2 (which doesn't appear to be the same as cat4500+e-promupgrade-150_1r_SG2 ). Where the correct file is?Since I have dual supervisors, it says I should upgrade the software, then the ROMMON. If I can do that (run the new software with the old ROMMON) why am I bothering to upgrade the ROMMON in the first place? (update, ok, I see the new ROMMON gives me enhanced crash info and will allow future upgrades without bringing down both supervisors at the same time).When these were ordered/installed, the licenses were all mixed up (I wasn't involved with that ). So the MDFs have dual sup 7e with ipbase and the IDFs have single sup 7e with enterprise services. Obviously, we want the enterprise services in the MDF so we can run OSPF and the ipbase in the IDF. But, OSPF seems to be running just fine in the MDF on ipbase. Are the licenses not enforced on these platforms? The release notes for 3.2.0 say ipbase doesn't support OSPF. So if I upgrade the MDF switches, will OSPF suddenly stop working?
The IP Base image does not support enhanced routing features such as Nonstop Forwarding (NSF) , BGP, Enhanced Interior Gateway Routing Protocol (EIGRP), Open Shortest Path First (OSPF), Intermediate System-to-Intermediate System (IS-IS), Virtual Routing Forwarding (VRF-lite) and policy-based routing (PBR).
Cisco Switching/Routing :: Configure NAT On A 4510R+E?
Dec 22, 2012I notice that NAT is not possible Cisco Catalyst 4500e series. Is there any other ways to configure NAT? Currently we have 2x Catalyst 6509 and we're migrating to the 4510e and there's NAT in the 6509s. I was thinking of re-using the 6509s and connect to the 2 new 4510e in a meshed trunking layout with MST (Layer 2) and OSPF/EIGRP (Layer 3) protocols turned on.
View 1 Replies View RelatedCisco Switching/Routing :: Netflow On Cat 4510R+E With IOS-XE?
Feb 11, 2012I am trying to figure out the Flexible Net-flow on Cat 4510R+E Switch running IOS-XE code. My Neflow flow software is manageengine 7.X. I am able to see the netflow interfaces but the traffic itself is not displayed. On the Switch I can see the netflow exporter statistics counter being incremented thereby confirming as being exported.
View 2 Replies View RelatedCisco Switching/Routing :: 4510R Can Still Use OM3 Patch Cable
Jan 21, 2008We have a new building, and I told the cable company run OM3 cable from second floor to 1st FL data closet because we have 4510R SupV-10G at each floor.However, the cable company ran a regular fiber cable instead of OM3 mistakenly. My questions, can I still use OM3 patch cable?? Second questions, can I still have the 10Gig performance??
View 3 Replies View RelatedCisco Switching/Routing :: Catalyst 4510R+E Supervisor 7-E SSO Not Available
Sep 22, 2011I'm working on deploying a new 4510R+E for our organization. This is my first experience with a modular switch. I'm trying to enable SSO, however in the redundancy configuration mode, the sso command is not available. Is SSO only available with certain software images / licensing levels? [code]
View 2 Replies View RelatedCisco Switching/Routing :: 4510R E High Cpu Utilization On One Core
Dec 13, 2011We have cisco 4510R+E switch with IOS-XE Software Version 03.01.01.SG RELEASE SOFTWARE (fc1).Our this switch is having two core & one core is always going to about 90% to 98% cpu utilization while other core is showing normal (about 5% to 10%),we check with-This switch is gateway of our LAN.
View 6 Replies View RelatedCisco Switching/Routing :: Wireless APs Are Not Coming Up Of New Catalyst 4510R-E PoE
Sep 10, 2012We have recently purchased Catalyst 4510R-E with two PoE line cards. When we connected Cisco Wireless APs to Cat4510 PoE ports it did not come up. These WAPs are working fine on other Cisco switch with PoE ports so there is no issue with WAP. We have received two CAT4510 and on both two slots are populated with PoE line cards and on both switches WAPs are not coming up. PC/desktops are working fine on these ports.Is there any configuration required on Cat4510 to enable PoE feature.
View 15 Replies View RelatedCisco Switching/Routing :: Moving Line Cards On 4510R-E?
Apr 2, 2013We need to move some line cards around on our 4510. The top slots have a 24Gbps backplane while the lower slots are limited to 6Gbps. Poor planning on our part has left us with installing a 10Gb line card in one of the bottom slots. I'd like to move a couple of the cards up top, to the bottom.
My question is simply will the switch magically preserve the configuration for those cards and change the slot number for me or will I need to reconfigure the interfaces for those cards I move?
Cisco Switching/Routing :: Upgrading Line Cards - 4510R-E
Feb 4, 2013I have a requirement to upgrade some line cards in our 4510R-E chassis to ease some oversubscription due to the 6Gbps limit.
At the moment my plan is to upgrade three cards from WS-X4548-GB-RJ45 to X4648 to get the 24Gbps per card.
Supervisors are 6-E
1. Is this a viable plan?
2. If so can the cards be hot-swapped?
3. Would the new cards retain the existing interface settings of the previous cards?
4. Any gotchas to look out for?
Cisco Switching/Routing :: How Much Power Required From Utility Or UPS For 4510R Switch
Nov 13, 2011We have one switch 4510R which could have total 300 cisco GE color phone connected. That means 300x15.4=4620W. Considering the 89% effiency for the PoE line cards, that means each line card needs 5191W input power from chasis power supply. Based on the 6000W power supply specs, only up to 4800W is allocated for PoE purpose. But we need 5191W from power supply which redundant mode can't offer. We don't want to go with combined mode. So should we add external power shelf to add more power?Another question will be how much power we need from utility or UPS. For example, the efficency of cisco power supply is 75% and we use two 6000W power supplies in redudant mode. Then we need 8000W. The voltage is 220V. Then the AMP we need is 36.4A from UPS or utility power.
View 2 Replies View RelatedCisco Switching/Routing :: 4510R L3 / Make Active Sup6 In Slot 6 Which Is Currently Standby Sup In Chassis
Mar 25, 2013I have cisco 4510R L3 switch with installed 2 Sup on slot 5 and 6. the current active Sup is in Slot5 i want to make active Sup6 in slot 6 which is currently standby sup in chassis. Is there any way to make standby Sup to ACTIVE without reloading any of the Supervisor. however there is two way as per my understanding -
1. we can reload the active Sup so that standby Sup will take charge. - (redundancy reload shelf)
2. we can focefully switchover the state of Sup's by (redundancy forcefully swithover) but in above both cases reload will be performed by one of the supervisor. which i don't want.
Cisco Switching/Routing :: 10Ge Interface Can Be Set Down To 1Ge If Required
Nov 17, 2011How to confirm if a 10Ge interface can be set down to 1Ge if required ?
View 4 Replies View RelatedCisco Switching/Routing :: 4948 10GE Red Status LED?
Jun 5, 2013We had to transport one of our 4948 10 GE to another Data Centre and when we got it there and tried to power up its System Status LED was red and we cannot even get console to the device.
We can try to see if the switch is completely dead and needs replacing or is there something we can do to get it back up and running again?
Cisco Switching/Routing :: 10Ge Between Catalysts 6500
Nov 18, 2012I am in front of a choice what to select to deploy 10Ge in my datacenter to get four 6504e and two 3750x units connected to each other.All devices are located in 3-7 meters away from each other.The choice is whether to go for a multimode fiber and 10GBASE-SR X2 Modules OR cat7 UTP and 10GBASE-T X2 pluggable transceiver.Money wise it doesn't matter.Fiber looks less attractive since it's fragile and a bit harder to put in underfloor area.Cat7 is more attractive but there are 2 points:
1) I couldn't find ANY single photo of a 10GBASE-T (a module with a single RJ45 port). How does it look? Does it come with a cable or...??
2) How stable is it to run 10Ge over UTP?
Cisco Switching/Routing :: VSS With 4 Supervisor Engine 2T-10GE
May 6, 2013We have a scenario with 2 chassis, both with 2 supervisor Engine 2T, we try to make a configuration of VSS with the chassis and would link to know if is possible have 2 supervisor on chassis one and 2 supervisors on chassis 2 with VSS?
Router#sho switch virtual redundancy
My Switch Id = 1
Peer Switch Id = 2
Last switchover reason = active unit removed
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
[code]....
would like to use the second supervisors for obteind the local redundancy en chassis 1 and 2, this is possible?
the actually version on four supervisors is: s2t54-ipservicesk9-mz.SPA.150-1.SY3.bin
Cisco Switching/Routing :: Radius Server Command Missing From Global Configuration Mode 4510R
Feb 22, 2013I came across an interesting issue and thought I would see if anyone else has encountered it before contacting TAC.I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54).
View 2 Replies View RelatedCisco Switching/Routing :: Radius Server Command Missing From Global Configuration Mode 4510R-E
Apr 23, 2012I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54). With the background set, one switch reports the following:SwitchA (config)#r?radius-server redundancy regexp represourc rmon route-map router.
View 4 Replies View RelatedCisco Switching/Routing :: 4510R-E / Unable To Create A Port-channel And Apply Auto-qos For VOIP
Sep 15, 2011I have a 4510R-E chassis with SUP7-E running IOS XE version 3.01.01.SG. I am unable to create a port-channel and apply auto-qos for VOIP.If I configure auto-qos on the physical interfaces, I get this message when I try adding them to the port channel:
"The attached policymap is not suitable for member either due to non-queuing actions or due to type of classmap filters."
Auto-qos is not an available command in the port-channel interface configuration, but if I try adding the service policies that were created by auto-qos to the port channel manually, it lets me apply the input policy but on the output policy I get this message:
"A service-policy with queuing actions can be attached in output direction only on physical ports."
With the input policy applied to the port-channel interface, I tried addign the output policy to the physical ports and I got this message:
"A service-policy with non-queuing actions should be attached to the port-channel associated with this physical port."
Is there a way to get the auot-qos policies applied to the port-channel properly?
Cisco Switching/Routing :: RP / Input Drops On 6500 Sup 720 10GE
Jun 17, 2012What does RP drops entail? We are experiencing 0.23 % drops on an vlan int on one of our 6500. This interface is an L3 to a server-subnet. Doing a sh int vlan 238 switching shows 30935411 RP (Route Processing) drops.It was a bit unclear to me in the thread "Input queue drops on 6500 vlan interface" if RP drops was through the router, or to the router(mgmnt)?I can do a netdr to see what traffic goes to it. It should not generate CPU load, but I think I will wait until after hours before I try that command.
- do NETDR:
-- debug netdr cap rx vlan 238
-- show netdr cap
Cisco Switching/Routing :: Stacking Or 10GE Link Between Two 3750
Jan 22, 2013We have two 3750 stackable switches in core layer.
1. We are planning to stack two 3750 for greater bandwidth to use
2. We could configure 10GE link (by Network module) between these two switches
which solution provides increased bandwidth and redundancy?
Cisco Switching/Routing :: 6509 LACP To Force10 10Ge?
Feb 7, 2013I am trying to configure a 6509 as the passive receiver from a Dell Force10 10Ge switch with 2 sfp to 2 gig ports on our 6509 switch, I see LACP is up on both sides but cannot pass traffic, I have only 2 vlans that will carry across the aggregate link from our vmware boxes, this is just a temp until I get a 10ge in our 6509 chassis.
View 2 Replies View RelatedCisco Switching/Routing :: 6513 Compatibility With 10GE Blades
Jun 4, 2012I am getting conflicting info about this, and need to get confirmations.Is the older 6513 (non E) model compatible with WS-X6407-10GE blade?The switch we're getting this for have WS-SUP720-3B, 6000W power supply, and WS-C6K-13SLT-FAN2.From what I read they are compatible if entered in slot 9-13, but I also heard that 10GE modules are not compatible with the non E chassis.
View 1 Replies View RelatedCisco Switching/Routing :: Possible To Use N2K-C2232TM-10GE Standalone As Other L2 Switches
Feb 27, 2013I am looking for 10 GE copper 24 ports switch. After any time I come N2K-C2232TM-10GE. However, this switch is fabric extender and it is used with Nexus 5K series switches.
My question is Can I use this Nexus 2K standalone as other L2 switches?
Cisco Switching/Routing :: Add WS-X6716-10GE Card In CAT6509
Sep 8, 2011I will be adding two WS-X6716-10GE cards in a CAT6509 soon, and will create 4 port channels with 3 ports each in the new cards, but I do have a few questions:
1 - I will be adding cards in slots 3 and 8, can I mix and bundle ports from both modules into a single etherchannel, I mean, like two ports in slot 3 and 1 port in slot 8 to create a PortChannel ?! Or can I only bundle ports in the same card/port-group in a Etherchannel using this WS-X6716-10GE card?
2 - Do I need to issue the hw-module slot x oversubscription port-group y command in order to be able to bundle ports in the Etherchannel I need to create ?! I will be using 4 Etherchannels (LACP) with 3 ports each, running in trunk mode. So I guess, I will be using something like:
int tengig 3/1
switchport mode trunk
switchport trunk encapsulation dot1q
logging event link-status
[Code] ....
Cisco Switching/Routing :: WS-X4516-10GE Works With WS-X4612-SFP-E?
Dec 4, 2011Is it possible that catalyst 4500 Supervisor Engine V-10GE WS-X4516-10GE works with WS-X4612-SFP-E?I know suprtvisor engine V-10GE is not support E-serious linecard, but when I use the configuration tool, I can choose these two products together. Is it a bug?I need novell IPX in this case, I find supervisor 6E & 7E are already not support, so I have no choice to choose V-10GE.
View 1 Replies View RelatedCisco Switching/Routing :: 4507 R-E With Sup 10GE Factory Reset
Jul 29, 2012I have been trying to reset my Cisco 4507 R-E with sup 10GE engines, and I am not having any luck. I have followed the following document:
[URL]
I have tried "wr erase" and "erase startup-config." I cannot delete the vlan.dat file either. I am using the command "erase cat4000_flash:vlan.dat" and its not working either. I have done these commands several times with no success. When asked if I want to save the config changes, I am answering with a "no" I have not tried to depress the small "reset" button on the front of the sup engines as I read that this just restarts the switch.
Cisco Switching/Routing :: Setup Management VRF On 4948-10GE
Aug 3, 2011I am trying to setup the management vrf on the 4948 10GE so that my TACACS requests will use that vrf for out-of-band purposes. The vrf is working properly because I can ping the TACACS server using the vrf but the logins do not work. I see this error in the tacacs debug:
TPLUS(00000016)/0: Connect Error No route to host
Looking at the release notes, it states that my version (12.2.54 SG1) does support vrf aware tacacs but the documentation seems to be a bit off because i do not get a server private command option as stated in the configuration doc after configuring a tacacs server group:
[URL]
Here is my config:
ip vrf mgmtVrf
rd X:X
!
interface FastEthernet1
ip vrf forwarding mgmtVrf
ip address x.x.x.x
[code]....
Cisco Switching/Routing :: Unsupported Module On 4500e SupV 10GE
Jan 17, 2012When i swapped a Sup v 10 ge for a Sup6 E Tonight in order to take advantage of the netflow capabilites of the Sup V - It came up with module unsupported for the following cards - WS-X4648-RJ45V-E Will these only work with the Sup6 E or what
View 2 Replies View RelatedCisco Switching/Routing :: 4948-10GE No Login After IOS Update To Version 15.0
Oct 25, 2011ive updated my catalyst 4948-10GE to version 15.0(2)SG1.Now it is not possible to login by ssh or telnet on this switch. the access is established over the mgmt-Interface and vrf.i get a ping reply but login is no more possible now.is there an new feature in this version for vrf or remotelogin that has to be configured? if neccessary i can paste the running-config here.
View 3 Replies View RelatedCisco Switching/Routing :: 10GE On 2960 Switch Connect To Server?
Sep 11, 2011just want to confirm if I could use the 2x 10GE uplink ports of a cisco 2960 to connect to my Server directly?
View 17 Replies View Related
