Cisco Switching/Routing :: 4510R+E - Dual Sup 7e Software / ROMmon Upgrade?

Jun 1, 2011

We have some 4510R+E with dual sup 7e that have experienced problems recently.  One of the sup 7e's crashed with a "critical software exception":
 
#show verCisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.01.01.SG RELEASE SOFTWARE (fc1)
<snip>
ROM: 15.0(1r)SG1
<snip> Last reload reason: Critical software exception, check bootflash:crashinfo_iosd
  
So I thought I'd upgrade to IOS-XE 3.2.0SG to hopefully resolve the issue.  I was reading the software release notes and it says:
 
If you are upgrading to 3.2.0SG, you must upgrade your ROMMON to 15.0(1r)SG2.If they have dual supervisors, first upgrade your software to 3.2.0SG, then upgrade your ROMMON to15.0(1r)SG2 to avoid the resets uplinks issue (CSCtj54375). 

And from the ROMMON release notes it says:
 
Download the cat4500+e-promupgrade-150_1r_SG2 program from Cisco.com, and place it on a TFTPserver in a directory that is accessible from the switch that is upgraded.The cat4500+e-promupgrade-150_1r_SG2 program is available on Cisco.com at the same location from which Catalyst 4500 system images are downloaded. 
 
So I have several questions:
 
The only promupgrade file I can find is cat4500-e-ios-promupgrade-150-1r-SG2  (which doesn't appear to be the same as cat4500+e-promupgrade-150_1r_SG2 ). Where the correct file is?Since I have dual supervisors, it says I should upgrade the software, then the ROMMON.  If I can do that (run the new software with the old ROMMON) why am I bothering to upgrade the ROMMON in the first place? (update, ok, I see the new ROMMON gives me enhanced crash info and will allow future upgrades without bringing down both supervisors at the same time).When these were ordered/installed, the licenses were all mixed up (I wasn't involved with that   ).  So the MDFs have dual sup 7e with ipbase and the IDFs have single sup 7e with enterprise services. Obviously, we want the enterprise services in the MDF so we can run OSPF and the ipbase in the IDF.  But, OSPF seems to be running just fine in the MDF on ipbase.  Are the licenses not enforced on these platforms?  The release notes for 3.2.0 say ipbase doesn't support OSPF.  So if I upgrade the MDF switches, will OSPF suddenly stop working? 
 
The IP Base image does not support enhanced routing features such as Nonstop Forwarding (NSF) , BGP, Enhanced Interior Gateway Routing Protocol (EIGRP), Open Shortest Path First (OSPF), Intermediate System-to-Intermediate System (IS-IS), Virtual Routing Forwarding (VRF-lite) and policy-based routing (PBR).

View 1 Replies


ADVERTISEMENT

Cisco Switching/Routing :: 4510R-E With Dual SUP V / 10GE IOS Upgradation

Sep 23, 2012

We have CORE switch model : Cisco WS-C4510R-E with dual SUP 5 - 2 10GE. [code] Now We want to upgrade this IOS to the upgraded version.

View 3 Replies View Related

Cisco Switching/Routing :: High CPU Utilization On 4510R Switch With Dual SUP V -10G

Feb 14, 2012

We have a problem of igh CPU Utilization in Cisco 4510R-with dual SUP V-10G modules.
 
Cisco 4510R switch is the CORE switch and have 30 no's of VLans. It was running PVST/PVST+ previously. But Now we have migrated to MST. But after upgradation the CPU utilization reached alomst 98%.

View 2 Replies View Related

Cisco Switching/Routing :: 871 Not Enter ROMmon After Flash Upgrade

Dec 12, 2012

I tired to upgrade the flash memory on my 871. I have tired to send single break and removing the flash card to drop the 871 to rommon.  but no luck, all i get is the below error. I have try restart button on the back and get the same results. How to get the router into rommon mode so i can place the IOS on the flash ?

View 5 Replies View Related

Cisco Switching/Routing :: 6509 Upgrade To 12.2(33)SXI10 And ROMmon?

Dec 12, 2012

I have ROM MON version 12.2(17r)S2 and I am trying to determine if I need to chnage this to 12.2(17r)SX7. It does not appear I need to  with the upgrade to 12.2(33)SXI10. Is this correct?

View 1 Replies View Related

Cisco Switching/Routing :: C2960 / Firmware Error After Upgrade - Cannot Get To ROMmon

Aug 14, 2012

Yesterday I tried to install c2960-lanbasek9.mz.12.55.SE4.bin onto my router.  When I changed the boot commands, I did not leave the 2nd option in there and the old firmware has an .ex3 extension.  After trying to boot to this new image, we receive a looping error message that continues to reboot and go through the same process.Basically the error is  "ERROR: firmware not supported by hardware"I have power cycled it a few times but durning bootup, I never see the ################## which would allow me to BREAK sequence and get into rommon.  The device simply waits about 30-40 seconds after boot and goes right back to the looping reboot sequence and the error message.  Is there any hyper term or putty settings to change on this?

View 1 Replies View Related

Cisco Switching/Routing :: Dual Core / SUP 720 6500 IOS Upgrade?

Apr 29, 2012

Doing a bug scrub on our dual core, dual Sup 720 6500s tonight. We are going from s72033-advipservicesk9_wan-mz.122-33.SXI4a.bin to SXI9. I want to get a second set of eyes on my script since I have not done this for about 1 1/2 years. Following this doc:[URL]  
 
Script:
 
Backup
sh ver
remote command switch show version

[Code].....

View 6 Replies View Related

Cisco Switching/Routing :: Upgrade IOS Software Image On 4507R+E With Dual Sup6L-E

Jun 27, 2012

Is there any docs with step by steps on upgrading the IOS software image on 4507R+E with dual sup6L-E ?

View 3 Replies View Related

Cisco Switching/Routing :: Configure NAT On A 4510R+E?

Dec 22, 2012

I notice that NAT is not possible Cisco Catalyst 4500e series. Is there any other ways to configure NAT? Currently we have 2x Catalyst 6509 and we're migrating to the 4510e and there's NAT in the 6509s. I was thinking of re-using the 6509s and connect to the 2 new 4510e in a meshed trunking layout with MST (Layer 2) and OSPF/EIGRP (Layer 3) protocols turned on.

View 1 Replies View Related

Cisco Switching/Routing :: Netflow On Cat 4510R+E With IOS-XE?

Feb 11, 2012

I am trying to figure out the Flexible Net-flow on Cat 4510R+E Switch running IOS-XE code. My Neflow flow software is manageengine 7.X. I am able to see the netflow interfaces but the traffic itself is not displayed. On the Switch I can see the netflow exporter statistics counter being incremented thereby confirming as being exported.

View 2 Replies View Related

Cisco Switching/Routing :: 4510R Can Still Use OM3 Patch Cable

Jan 21, 2008

We have a new building, and I told the cable company run OM3 cable from second floor to 1st FL data closet because we have 4510R SupV-10G at each floor.However, the cable company ran a regular fiber cable instead of OM3 mistakenly. My questions, can I still use OM3 patch cable??  Second questions, can I still have the 10Gig performance??

View 3 Replies View Related

Cisco Switching/Routing :: 4510R - SUP V-10GE Uplink

Jan 28, 2013

I have a two Cisco 4510R each with two sup V-10GE redundant. The code on these sup modules are 12.2(31r)SG3. I need some assistance in getting this setup worked out. I have all four of the 10GE populated with appropriate optics. I setup a link from one 4510R to the other using these interfaces. From the documentation I found I had to use Tengi1/1 and Tengi2/2 as the redundant pair. I plugged the up link into these ports. The Tengi1/1 (active supervisor) links up and works fine. But when I look at the ports port Tengi2/2 it isn't showing link or active. Now port 2/1 (nothing plugged into it) is showing as active.
 
Now is the redundancy supposed to be 1/1 and 2/1? If so, the switch is in production, when I move the connection over from 2/2 to 2/1 will it cause a outage? The reason for this is I now have a system with a 10G port and would like to utilize one of the other 10G ports. Is that possible? Or does it have to be a lag/redundant up link to work (say to another switch)?

View 2 Replies View Related

Cisco Switching/Routing :: Catalyst 4510R+E Supervisor 7-E SSO Not Available

Sep 22, 2011

I'm working on deploying a new 4510R+E for our organization.  This is my first experience with a modular switch.  I'm trying to enable SSO, however in the redundancy configuration mode, the sso command is not available.  Is SSO only available with certain software images / licensing levels? [code]

View 2 Replies View Related

Cisco Switching/Routing :: 4510R E High Cpu Utilization On One Core

Dec 13, 2011

We have cisco 4510R+E switch with IOS-XE Software Version 03.01.01.SG RELEASE SOFTWARE (fc1).Our this switch is having two core & one core is always going to about 90% to 98% cpu utilization while other core is showing normal (about 5% to 10%),we check with-This switch is gateway of our LAN.

View 6 Replies View Related

Cisco Switching/Routing :: Wireless APs Are Not Coming Up Of New Catalyst 4510R-E PoE

Sep 10, 2012

We have recently purchased Catalyst 4510R-E with two PoE line cards. When we connected Cisco Wireless APs to Cat4510 PoE ports it did not come up. These WAPs are working fine on other Cisco switch with PoE ports so there is no issue with WAP. We have received two CAT4510 and on both two slots are populated with PoE line cards and on both switches WAPs are not coming up. PC/desktops are working fine on these ports.Is there any configuration required on Cat4510 to enable PoE feature.

View 15 Replies View Related

Cisco Switching/Routing :: Moving Line Cards On 4510R-E?

Apr 2, 2013

We need to move some line cards around on our 4510.  The top slots have a 24Gbps backplane while the lower slots are limited to 6Gbps.  Poor planning on our part has left us with installing a 10Gb line card in one of the bottom slots.  I'd like to move a couple of the cards up top, to the bottom.
 
My question is simply will the switch magically preserve the configuration for those cards and change the slot number for me or will I need to reconfigure the interfaces for those cards I move?

View 2 Replies View Related

Cisco Switching/Routing :: Upgrading Line Cards - 4510R-E

Feb 4, 2013

I have a requirement to upgrade some line cards in our 4510R-E chassis to ease some oversubscription due to the 6Gbps limit.
 
At the moment my plan is to upgrade three cards from WS-X4548-GB-RJ45 to X4648 to get the 24Gbps per card.
 
Supervisors are 6-E
 
1. Is this a viable plan?

2. If so can the cards be hot-swapped?

3. Would the new cards retain the existing interface settings of the previous cards?

4. Any gotchas to look out for?

View 4 Replies View Related

Cisco Switching/Routing :: How Much Power Required From Utility Or UPS For 4510R Switch

Nov 13, 2011

We have one switch 4510R which could have total 300 cisco GE color phone connected. That means 300x15.4=4620W. Considering the 89% effiency for the PoE line cards, that means each line card needs 5191W input power from chasis power supply. Based on the 6000W power supply specs, only up to 4800W is allocated for PoE purpose. But we need 5191W from power supply which redundant mode can't offer. We don't want to go with combined mode. So should we add external power shelf to add more power?Another question will be how much power we need from utility or UPS. For example, the efficency of cisco power supply is 75% and we use two 6000W power supplies in redudant mode. Then we need 8000W. The voltage is 220V. Then the AMP we need is 36.4A from UPS or utility power.

View 2 Replies View Related

Cisco Switching/Routing :: 4510R L3 / Make Active Sup6 In Slot 6 Which Is Currently Standby Sup In Chassis

Mar 25, 2013

I have cisco 4510R L3 switch with installed 2 Sup on slot 5 and 6. the current active Sup is in Slot5 i want to make active Sup6 in slot 6 which is currently standby sup in chassis. Is there any way to make standby Sup to ACTIVE without reloading any of the Supervisor. however there is two way as per my understanding -

1. we can reload the active Sup so that standby Sup will take charge. - (redundancy reload shelf)

2. we can focefully switchover the state of Sup's by (redundancy forcefully swithover) but in above both cases reload will be performed by one of the supervisor. which i don't want.

View 2 Replies View Related

Cisco Switching/Routing :: Radius Server Command Missing From Global Configuration Mode 4510R

Feb 22, 2013

I came across an interesting issue and thought I would see if anyone else has encountered it before contacting TAC.I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis.  Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story.  Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code.  The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54). 

View 2 Replies View Related

Cisco Switching/Routing :: Radius Server Command Missing From Global Configuration Mode 4510R-E

Apr 23, 2012

I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis.  Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story.  Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code.  The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54).  With the background set, one switch reports the following:SwitchA (config)#r?radius-server  redundancy regexp represourc rmon route-map router.

View 4 Replies View Related

Cisco Switching/Routing :: 4510R-E / Unable To Create A Port-channel And Apply Auto-qos For VOIP

Sep 15, 2011

I have a 4510R-E chassis with SUP7-E running IOS XE version 3.01.01.SG.  I am unable to create a port-channel and apply auto-qos for VOIP.If I configure auto-qos on the physical interfaces, I get this message when I try adding them to the port channel:
 
"The attached policymap is not suitable for member either due to non-queuing actions or due to type of classmap filters."
 
Auto-qos is not an available command in the port-channel interface configuration, but if I try adding the service policies that were created by auto-qos to the port channel manually, it lets me apply the input policy but on the output policy I get this message:
 
"A service-policy with queuing actions can be attached in output direction only on physical ports."
 
With the input policy applied to the port-channel interface, I tried addign the output policy to the  physical ports and I got this message:
 
"A service-policy with non-queuing actions should be attached to the port-channel associated with this physical port."
 
Is there a way to get the auot-qos policies applied to the port-channel properly?

View 3 Replies View Related

Cisco Switching/Routing :: Nexus 5596UP Dual-sided VPC Design With Dual Connected

Feb 19, 2012

I would like to make a design with 4 Nexus 5596UP. 2 of them equipped with Layer 3 Expansion Module  so they can serve as core layer and the other 2 Nexus used as Layer 2 for aggregation server layer.The 2 Nexus in the core layer will run HSRP and will peer with ISP via BGP for Internet connection The 2 Nexus in the aggregation layer will be configured as layer 2 device and have FEX and switches connected to them.What I am ensure of is how the vpc and port-channel configuration should look like between the 4 nexus. What I was thinking is to run vpc between the 2 Nexus in the aggregation layer and between the 2 Nexus in the core layer. Than I was thinking of connecting each Nexus in the aggragtion layer to both Nexus in the core layer using port-channel and vice-versa.

View 3 Replies View Related

Cisco Switching/Routing :: Cat 6506 Goes Into ROMmon

Nov 29, 2012

I have a Cat6506.  There were 2 Sup 720 in it for redundancy.  They told me they had problems with this thing in the past needing to go out and reboot the machine.  I need to go out periodically because it goes into ROMMON.  I type boot and it comes back up.  One time though neither one would reboot.  I had to take a third one out there and reconfigure it.  Now it is starting to do the same thing.  One thing I did notice is they never connected it to an UPS.  It is plugged strait into the wall with power going to two outlets.  I am beginning to think there are spikes in the power occurring and this is sending it into ROMMON. 

View 6 Replies View Related

Cisco Switching/Routing :: 3560E - Can't Get Into ROMmon

Sep 2, 2010

I upgraded four 3560E, 12.2(44) to 12.2(55)SEThree 3560 works fine, the last one stops after 17-18 seconds with a solid green LED. I cant get into ROMmon, the switch doesn't boot up. its like "dead but still alive"
 
My TS:
1: Removed all SFPs.
2: Reset PSU and fan modules.
3: Replace PSU and fan modules.
4: Try to get into ROMmon.(pushing mode button and break seq.)
Startup LED:0-1 seconds:    SYST: Amber    RPS: Amber    STAT: Green    DUPLEX: Green    SPEED: Green
1-17 seconds    SYST: Blinking Green    RPS: OFF    STAT: OFF    DUPLEX: OFF    SPEED: OFF
18 s--> (only testet up to one hour)    SYST: Solid Green    RPS: OFF    STAT: OFF    DUPLEX: OFF    SPEED: OFF
 
A working 3560EStartup LED information. If I compare a working switch with the faulty switch I can see about 18 seconds into bootingSYST change very fast from green to amber and continues with booting,this doesnt happened on the faulty switch (solid green 18 seconds).   Pushing MODE button, doesn't get me in to ROMmon, this works for all the other switches.On a normal 3560 it takes around 40 seconds before I get in to ROMmon. With this faulty switch it stops after 18 seconds(solid green) and it doesnt respond.

View 7 Replies View Related

Cisco Switching/Routing :: 4507 Went Into ROMmon

Jun 4, 2012

Could not find a valid file in BOOT environment variable. BOOT variable can be set from IOS. To find currently setRom Monitor variables, type 'set' command.

Choosing a boot method,  type 'confreg' command.rommon 1

>setPS1=rommon ! >RommonVer=15.0(1r)SG5SupportedFeatures=1ConsecPostPassedCnt=2DiagMonitorAction=NormalCONFIG_FILE=bootflash:cat4500e-

[Code].....

View 11 Replies View Related

Cisco WAN :: ASR 1002 IOS And ROMmon Upgrade

Jan 10, 2011

I'm trying to upgrade the ASR 1002 we just purchased and am having some issues (this is a new device and is not in service).  I first tried upgrading the ROMMON using the upgrade rom-monitor filename bootflash:asr1000-rommon.150-1r.S.pkg all command, but the upgrade didn't seem to work completely.  When I do a sh platform I get the below output showing 15.0(1r)S: [code]
 
no valid BOOT image foundFinal autoboot attempt from default boot device...Rommon upgrade requestedMaximum upgrade attempts exceeded, continuing with old Rommon...
 
I've also tried upgrading the IOS, but that is not working either.  I tried "boot system flash:asr1000rp1-advipservicesk9.03.02.00.S.151-1.S.bin" command, but that did not work.  I made sure the image was good using the "verify" command and made sure to set "config-register 0x2102".  After I do a wr me and reload the router I get the below errors. [code]

View 1 Replies View Related

Cisco Switching/Routing :: Cannot Get Out Of Rommon Mode 1760

Dec 10, 2011

I'm currently pursuing to take my CCNA and am currently studying for it, but have recently encountered a problem with one of my 1760 routers that I can not solve.Yesterday I went to boot up my router like normal, however when I went into hyperterminal I noticed the router was in Rommon mode. Thinking I could change the configuration registry, I tried to bypass the NVRAM by using confreg 0x2142. However this still causes the router to go into Rommon mode. I am getting an error that states that there is insufficient memory to load the IOS image. [code]
 
I have used the dir flash: command and can see the IOS image, and try to boot from it (boot flash:iosimagename) but it will still go back into rommon mode. I also just swapped the RAM from my other 1760 into this 1760 and it booted up and went into normal configuraiton mode without any issues. However, the other router now will not load it's IOS image and I get the exact same error.I'm at a loss here, and have searched to figure out where or how I can just wipe the router clean to try and start fresh, but cannot get out or Rommon mode. The only thing I can think of is that the RAM went bad since it wont boot up either machine.

View 1 Replies View Related

Cisco Switching/Routing :: 6503 Sup-2T Unable To Get Into ROMmon

Apr 11, 2013

I have an issue with a customers 6503 with Sup-2T cards, where we are locked out of the console due to an authentication configuration error. So tried several times to get the card into rommon, with no success.
 
Checking through the various documents on CCO I dont find any reference to rommon on this card, but do find information on using the CMP to support the supervisor. I logged into the CMP but couldn't find a way from there to do a password reccovery either.So, is the `normal' IOS rommon/password recovery method supported.

View 2 Replies View Related

Cisco Switching/Routing :: 6509 Goes In ROMmon On Reboot

Jul 24, 2011

I am facing a problem with a cisco 6509 that goes into rommon every time i restart. If i give the command
 
rommon 1> boot
 
it will pick up the IOS on the sup-bootdisk: or bootdisk: and boots up but i dont understand why on reboot it wont pick up this IOS and boot itself and why do i have to write boot command everytime on rommon.
 
I have also explicitly given the command "boot system bootdisk:IOSNAME.bin" in the startup config file but still no luck.

View 36 Replies View Related

Cisco Switching/Routing :: ASA5505 Booting Into ROMmon?

Jul 3, 2012

An ASA 5505. Device boots to rommon #0> and stays there. The complete boot record follows:
 
CISCO SYSTEMS
Embedded BIOS Version 1.0(12)13 08/28/08 15:50:37.45
Low Memory: 632 KB
High Memory: 507 MB

[Code]....

View 15 Replies View Related

Cisco WAN :: Unable To Upgrade ROMmon On 2801

Sep 7, 2011

I would like to upgrade rommon on my Cisco 2801 but this is what I get: [code]The router stops here and I am forced to power off and on again and the upgrade does not succeed.

View 10 Replies View Related

Cisco Switching/Routing :: 6509 Stuck In ROMmon Mode?

Dec 16, 2012

I have 6509 E.  Actually what happen it last 3-4 times it reload its self and got stuck in rommon mode, i tried to boot it with boot by connecting a console cable on supervisor 720 2b. What and where is problem and why is stuck in rommon after reload.

View 11 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved