Cisco Switching/Routing :: 6509 Upgrade To 12.2(33)SXI10 And ROMmon?

Dec 12, 2012

I have ROM MON version 12.2(17r)S2 and I am trying to determine if I need to chnage this to 12.2(17r)SX7. It does not appear I need to  with the upgrade to 12.2(33)SXI10. Is this correct?

View 1 Replies


ADVERTISEMENT

Cisco Switching/Routing :: 6509 Goes In ROMmon On Reboot

Jul 24, 2011

I am facing a problem with a cisco 6509 that goes into rommon every time i restart. If i give the command
 
rommon 1> boot
 
it will pick up the IOS on the sup-bootdisk: or bootdisk: and boots up but i dont understand why on reboot it wont pick up this IOS and boot itself and why do i have to write boot command everytime on rommon.
 
I have also explicitly given the command "boot system bootdisk:IOSNAME.bin" in the startup config file but still no luck.

View 36 Replies View Related

Cisco Switching/Routing :: 6509 Stuck In ROMmon Mode?

Dec 16, 2012

I have 6509 E.  Actually what happen it last 3-4 times it reload its self and got stuck in rommon mode, i tried to boot it with boot by connecting a console cable on supervisor 720 2b. What and where is problem and why is stuck in rommon after reload.

View 11 Replies View Related

Cisco Switching/Routing :: 6509 / 720 Sups Random ROMmon Boots

Dec 27, 2012

Got a long lingering, year long issue that has spanned about 8 supervisor cards and a complete chassis swap. The 6509 acts as a ITN in our facility. The active sup card at random points of pipe usage boots into rommon mode, seriously inhibiting our company. I'm able to swap the 2 fiber pairs that we had going into the active supervisor card into the secondary and usually this works for another random amount of time, however, today it occured within minutes of hooking up the fiber links. Sitting there for about 5 minutes it booted into ROMMON. When this happens, I'm able to boot the sup card back to good status. Previous remedial actions, other than replacing sup cards/chassis, was checking the config register and making sure it was x2102. Previously, it was not, and we corrected and reloaded and it took, we thought this would fix the problem, until today.

[code]....

View 5 Replies View Related

Cisco Switching/Routing :: Switch 6509 In ROMmon Mode After Power Outage?

Nov 28, 2012

We have a cisco catalyst 6509 with Supervisor Engine . After power outage, the switch always start in Rommon mode. Configuration register is 0X2102,  we want to it always start in normal mode. What should i do?

View 3 Replies View Related

Cisco Switching/Routing :: 6509 Redundant Sup720 - Slave Boots Into ROMmon

Oct 24, 2012

I'm fairly new to networking and need to migrate an old core to a new core. I have a 6509-e Switch that I had an RMA on one of my 720 sup cards. After receiving the sup card I swapped my slave out with the new one, expecting it to boot into ios. It booted into Roman. I tried to boot the image manually and it did the same thing. I also tried to boot from my flash and, again, booted into ROMmon.
 
Question: If i configure and change the boot to boot from image it tells me i need to reset or power cycle first. Will this reset the entire switch? As this is production I'd rather not.
  
I am at home now, but I can supply any logs/hardware model/configs tomorrow. I thought I would see if this is an easy fix.

View 23 Replies View Related

Cisco Switching/Routing :: 871 Not Enter ROMmon After Flash Upgrade

Dec 12, 2012

I tired to upgrade the flash memory on my 871. I have tired to send single break and removing the flash card to drop the 871 to rommon.  but no luck, all i get is the below error. I have try restart button on the back and get the same results. How to get the router into rommon mode so i can place the IOS on the flash ?

View 5 Replies View Related

Cisco Switching/Routing :: 6509 To 6509-E Chassis Upgrade?

Nov 21, 2011

I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:

     x3     48 ports
     x1     NAM
     x2     Sup720
     Running 12.2(18)SXF3
 
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?

View 2 Replies View Related

Cisco Switching/Routing :: Upgrade Of 6509 To 6509-E Chassis

Nov 21, 2011

I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:

x3     48 ports
x1     NAM
x2     Sup720

Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?

View 2 Replies View Related

Cisco Switching/Routing :: C2960 / Firmware Error After Upgrade - Cannot Get To ROMmon

Aug 14, 2012

Yesterday I tried to install c2960-lanbasek9.mz.12.55.SE4.bin onto my router.  When I changed the boot commands, I did not leave the 2nd option in there and the old firmware has an .ex3 extension.  After trying to boot to this new image, we receive a looping error message that continues to reboot and go through the same process.Basically the error is  "ERROR: firmware not supported by hardware"I have power cycled it a few times but durning bootup, I never see the ################## which would allow me to BREAK sequence and get into rommon.  The device simply waits about 30-40 seconds after boot and goes right back to the looping reboot sequence and the error message.  Is there any hyper term or putty settings to change on this?

View 1 Replies View Related

Cisco Switching/Routing :: 4510R+E - Dual Sup 7e Software / ROMmon Upgrade?

Jun 1, 2011

We have some 4510R+E with dual sup 7e that have experienced problems recently.  One of the sup 7e's crashed with a "critical software exception":
 
#show verCisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.01.01.SG RELEASE SOFTWARE (fc1)
<snip>
ROM: 15.0(1r)SG1
<snip> Last reload reason: Critical software exception, check bootflash:crashinfo_iosd
  
So I thought I'd upgrade to IOS-XE 3.2.0SG to hopefully resolve the issue.  I was reading the software release notes and it says:
 
If you are upgrading to 3.2.0SG, you must upgrade your ROMMON to 15.0(1r)SG2.If they have dual supervisors, first upgrade your software to 3.2.0SG, then upgrade your ROMMON to15.0(1r)SG2 to avoid the resets uplinks issue (CSCtj54375). 

And from the ROMMON release notes it says:
 
Download the cat4500+e-promupgrade-150_1r_SG2 program from Cisco.com, and place it on a TFTPserver in a directory that is accessible from the switch that is upgraded.The cat4500+e-promupgrade-150_1r_SG2 program is available on Cisco.com at the same location from which Catalyst 4500 system images are downloaded. 
 
So I have several questions:
 
The only promupgrade file I can find is cat4500-e-ios-promupgrade-150-1r-SG2  (which doesn't appear to be the same as cat4500+e-promupgrade-150_1r_SG2 ). Where the correct file is?Since I have dual supervisors, it says I should upgrade the software, then the ROMMON.  If I can do that (run the new software with the old ROMMON) why am I bothering to upgrade the ROMMON in the first place? (update, ok, I see the new ROMMON gives me enhanced crash info and will allow future upgrades without bringing down both supervisors at the same time).When these were ordered/installed, the licenses were all mixed up (I wasn't involved with that   ).  So the MDFs have dual sup 7e with ipbase and the IDFs have single sup 7e with enterprise services. Obviously, we want the enterprise services in the MDF so we can run OSPF and the ipbase in the IDF.  But, OSPF seems to be running just fine in the MDF on ipbase.  Are the licenses not enforced on these platforms?  The release notes for 3.2.0 say ipbase doesn't support OSPF.  So if I upgrade the MDF switches, will OSPF suddenly stop working? 
 
The IP Base image does not support enhanced routing features such as Nonstop Forwarding (NSF) , BGP, Enhanced Interior Gateway Routing Protocol (EIGRP), Open Shortest Path First (OSPF), Intermediate System-to-Intermediate System (IS-IS), Virtual Routing Forwarding (VRF-lite) and policy-based routing (PBR).

View 1 Replies View Related

Cisco Switching/Routing :: Getting 6509 VSS IOS Upgrade?

May 15, 2012

Tonight we were performing an IOS upgrade on our 6509 VSS to 122-33.SXI6.  Both 6509's have dual Supervisor cards installed.  Initially we had problems with switch 2 slot 5 supervisor returning to rommon however switch 2 slot 6 supervisor loaded correctly.  After manually setting the boot var in rommon, switch 2 slot 5 supervisor reloaded correctly.
 
After all supervisor's were online we noticed when looking at " show switch virtual redundancy" that sw 1 & 2 slot 6 supervisors were running the correct IOS version but sw 1 & 2 slot 5 were running different IOS versions, however when looking at the show version we are running on the upgraded IOS???  See output below...
 
Why the active supervisor has loaded the incorrect IOS the VSS is running on the upgraded IOS?  I have verified the IOS was copied correctly to each supervisor bootdisk, I see no issues. 
 
My Switch Id = 1                Peer Switch Id = 2        Last switchover reason = none    Configured Redundancy Mode = sso     Operating Redundancy Mode = sso
Switch 1 Slot 5 Processor Information :-----------------------------------------------        Current Software state = ACTIVE       Uptime in current state = 3 hours, 38 minutes                 Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)Technical Support:

[code].....

View 3 Replies View Related

Cisco Switching/Routing :: 6509 VSS IOS Upgrade

Jan 15, 2012

Will I be OK doing a eFSU Upgrade from s72033-ipservicesk9_wan-mz.122-33.SXI2a to s72033-ipservicesk9_wan-mz.122-33.SXJ1?
 
I only have a single supervisor in each chassis.
 
Should I be ok with just following the eFSU upgrade instructions in the below?
 
[URL]

View 1 Replies View Related

Cisco Switching/Routing :: Upgrade 6509-E Ios Image?

Jan 9, 2013

I am going to upgrade the IOS image on 6509-E SUP 2T  from 15.1 to s2t54-adventerprisek9-mz.SPA.150-1.SY3.bin switch and i would like to know whether i would need to upgrade the boot loader image as well.

View 4 Replies View Related

Cisco Switching/Routing :: 6509 SSO Redundancy IOS Upgrade

Sep 9, 2012

I have a 6509 switch with SSO Redundancy (STANDBY HOT) with IOS ver 12.2(17d)SXB11, RELEASE SOFTWARE (fc1) (c6k222-jk9sv-mz.122-17d.SXB11.bin). I need to upgrade the IOS on this switch.I have 512MB Memory on the switch and 40144896 bytes free on Disk0.which IOS is the latest version to upgrade and also give me some hints for IOS upgrade on this switch?

View 7 Replies View Related

Cisco Switching/Routing :: 6509 Sup Engine 32 IOS Upgrade Via USB

May 14, 2013

I would like to find out how to upgrade SUP engine 32 via USB port as I've never did IOS upgrade on a SUP engine via USB before

View 5 Replies View Related

Cisco Switching/Routing :: IOS Upgrade For VSS 6509 Switches

Nov 19, 2012

I have 2 6509 switches configured with VSS.As per advised my managment I have to enable SSH but it is not available existing IOS which is "s72033-ipbase-z.122-33.SXI3.bin". SSH available in "s72033-ipbasek9-mz.122-33.SXI10".
 
upgrade the IOS with VSS configured switches.

View 9 Replies View Related

Cisco Switching/Routing :: 6509 Supervisor IOS Upgrade

Oct 16, 2012

We are trying to upgrade the IOS on one of our 6509 switches. We have two 720 10GE supervisors running in SSO. Our procedure is reload the standby supervisor with the new IOS. We understand that you can only use one console connection when in RPR mode so we rely on the active supervisor giving us information that the standby unit is up and running.
 
The problem we have is that when we do a "show Module" on the switch the online diagnostics for the standby supervisor comes back us unknown. [code] We believe the active supervisor can see the standby supervisor because when we save the configuration we get a message saying that the config is sync'd with the standby router. We have a TAC case raised to investigate. We are upgrading from 12.2(33) SXI1 to 12.2(33) SXJ3

View 1 Replies View Related

Cisco Switching/Routing :: 6509-E VSS Will Upgrade Rewrite The Configuration

Jan 22, 2013

I am planning on upgrading my 6509s to use VSS within the next few weeks.  I have checked all of the hardware and software prerequisites, and we are good to go from that perspective.I do have more of a procedural question- my switches are already configured and in production, VLANs, HSRP (3 IP addresses per VLAN- 1 per switch plus virtual IP), etc.  Does the VSS upgrade take all of this into account and rewrite the configuration correctly, or should I plan on redoing the entire config for the switches after the upgrade?

View 6 Replies View Related

Cisco Switching/Routing :: 6509 Supervisor Upgrade With FWSM?

Oct 8, 2012

We are planning to upgrade the IOS on our two 6509E supervisors in the next few weeks. We currently run IOS 12.2(33) SXI1 and are upgrading to 12.2(33) SXJ3. At the moment the two supervisors are in SSO mode and after reading many articles it says that when the images are different on the two supervisors they are in RPR mode. When you then reload the active supervisor it will reboot all the line cards.
 
1. Is above correct? Will my line card reload?

2. We also have a FWSM installed, When/If the line cards are rebooted does the FWSM also reboot?

View 1 Replies View Related

Cisco Switching/Routing :: Upgrade SUP2 To SUP32 On 6509?

Sep 18, 2012

I am going to upgarde SUP2 to SUP32 on my 6509 by next week. right now I have 2 SUPs on the 6509 in redundant mode.

View 5 Replies View Related

Cisco Switching/Routing :: Upgrade 6509-Chassis In VSS-Environment?

May 1, 2013

we have some pairs of 6509-VSS, which partially have old (no more officially supported) 6509-Chassis.All linecards in the VSS are the same (Sup 720-10GE-3C, 67XX).
 
We now bought some new 6509-E-Chassis and want to change the old chassis by the new ones in a ISSU manner, that means:
 
1. putting the partner, which chassis changes, in redundancy mode, switch it off, exchange chassis (old "Catalyst 6509", new "Catalyst 6509-E")

2. inserting the line-cards exactly in the same slots and connecting all cables

3. switch on the new chassis, witing to come up in VSS
 
I'm not sure of having to set the switch number for VSS (is that in the Sup?; configuration? or part of the chassis-memory?)
 
I've looked up cisco for some hints, but don't found anything.

View 5 Replies View Related

Cisco Switching/Routing :: 6509 / Sup2 To Sup32 Upgrade?

Oct 7, 2012

I need to upgrade 2xsup2 module to 2xsup32 on my cisco 6509. I just found out that I can not have the CISCO WS-X6500-SFM(Cisco Switch Fabric Module switch) with Sup32 and I have to remove 2 xCISCO WS-X6500-SFM2 modules from the switch.I am using this switch as a access switch and most of the ports are 100Mbps.
 
let me know if the upgrade would be safe or not as far as the bandwidth?

View 2 Replies View Related

Cisco Switching/Routing :: 6509 - Upgrade Sup720 To Sup2T In VSS Cluster

Jun 21, 2012

I support an active VSS cluster using 2 x 6509E chassis with single Supervisor 3C modules in each chassis. I want to replace these with Supervisor 2T modules. All my service modules and line cards are supported with the Sup2Ts (I will also be implementing 6908 modules). Is there a document on the Cisco site for this? I haven't found one though I can find plenty that describe how to do a software upgrade.
 
(Note, I have a 3rd (non VSS) 6509E chassis that is also part of this core network and that will maintain VTP/V LAN's etc).

View 9 Replies View Related

Cisco Switching/Routing :: 6509 (HA) And FWSM (active / Standby) System Upgrade?

Sep 30, 2012

I have 2 6509 chasis with one SUP720-3B in each and current IOS is s72033-ipservicesk9_wan-mz.122-18.SXF4 and 2 FWSM with version is 3.3.1 I need to upgrade FWSM system software to 4.1, after checking FWSM 4.1 release notes, I thought of upgrading IOS to latest version  to 12.2(33)SXJ.I got new 2 CF of 512MB and downloaded the new IOS on them and need to upgrade 6509 IOS first to meet the requirement for FWSM upgrade.

View 1 Replies View Related

Cisco Switching/Routing :: 3750 / 6509 - Upgrade Core Switch Without Disrupting Network?

Feb 2, 2013

I am planning to upgrade the current core switch(3750) to 6509 series switch. Since we have a production network running we have to plan for an online core switch upgrade.

View 7 Replies View Related

Cisco Switching/Routing :: Sup32 Upgrade On 6509 - Priority Command Not Supported In Output Direction For This Interface

Nov 15, 2012

I have 1x Cisco 6509 with Sup2 and MSFC2 and it is running on IOS (c6k222-jk9sv-mz.122-17d.SXB11). I have following policy map :
 
Policy Map VOIP
Class IP PHONE
priority percent 75
 
and the following command on each interface: service-policy output VOIP those configuration are working fine on SUP2 with MSFC2 but last week I tried to upgrade the SUP2 to SUP32 on the switch and upgrade the IOS to the latest version (s3223-adventerprisek9-mz.122-33.SXJ4) but when I try to put service-policy output VOIP on each physical interface I am getting the following error: 
 
"Priority command is not supported in output direction for this interface" and when I try to add service-policy output VOIP on a V LAN interface I am getting following error:
 
MQC features are not supported in output direction for this interface. Will I need to change something after upgrading to SUP32..

View 3 Replies View Related

Cisco Switching/Routing :: Cat 6506 Goes Into ROMmon

Nov 29, 2012

I have a Cat6506.  There were 2 Sup 720 in it for redundancy.  They told me they had problems with this thing in the past needing to go out and reboot the machine.  I need to go out periodically because it goes into ROMMON.  I type boot and it comes back up.  One time though neither one would reboot.  I had to take a third one out there and reconfigure it.  Now it is starting to do the same thing.  One thing I did notice is they never connected it to an UPS.  It is plugged strait into the wall with power going to two outlets.  I am beginning to think there are spikes in the power occurring and this is sending it into ROMMON. 

View 6 Replies View Related

Cisco Switching/Routing :: 3560E - Can't Get Into ROMmon

Sep 2, 2010

I upgraded four 3560E, 12.2(44) to 12.2(55)SEThree 3560 works fine, the last one stops after 17-18 seconds with a solid green LED. I cant get into ROMmon, the switch doesn't boot up. its like "dead but still alive"
 
My TS:
1: Removed all SFPs.
2: Reset PSU and fan modules.
3: Replace PSU and fan modules.
4: Try to get into ROMmon.(pushing mode button and break seq.)
Startup LED:0-1 seconds:    SYST: Amber    RPS: Amber    STAT: Green    DUPLEX: Green    SPEED: Green
1-17 seconds    SYST: Blinking Green    RPS: OFF    STAT: OFF    DUPLEX: OFF    SPEED: OFF
18 s--> (only testet up to one hour)    SYST: Solid Green    RPS: OFF    STAT: OFF    DUPLEX: OFF    SPEED: OFF
 
A working 3560EStartup LED information. If I compare a working switch with the faulty switch I can see about 18 seconds into bootingSYST change very fast from green to amber and continues with booting,this doesnt happened on the faulty switch (solid green 18 seconds).   Pushing MODE button, doesn't get me in to ROMmon, this works for all the other switches.On a normal 3560 it takes around 40 seconds before I get in to ROMmon. With this faulty switch it stops after 18 seconds(solid green) and it doesnt respond.

View 7 Replies View Related

Cisco Switching/Routing :: 4507 Went Into ROMmon

Jun 4, 2012

Could not find a valid file in BOOT environment variable. BOOT variable can be set from IOS. To find currently setRom Monitor variables, type 'set' command.

Choosing a boot method,  type 'confreg' command.rommon 1

>setPS1=rommon ! >RommonVer=15.0(1r)SG5SupportedFeatures=1ConsecPostPassedCnt=2DiagMonitorAction=NormalCONFIG_FILE=bootflash:cat4500e-

[Code].....

View 11 Replies View Related

Cisco WAN :: ASR 1002 IOS And ROMmon Upgrade

Jan 10, 2011

I'm trying to upgrade the ASR 1002 we just purchased and am having some issues (this is a new device and is not in service).  I first tried upgrading the ROMMON using the upgrade rom-monitor filename bootflash:asr1000-rommon.150-1r.S.pkg all command, but the upgrade didn't seem to work completely.  When I do a sh platform I get the below output showing 15.0(1r)S: [code]
 
no valid BOOT image foundFinal autoboot attempt from default boot device...Rommon upgrade requestedMaximum upgrade attempts exceeded, continuing with old Rommon...
 
I've also tried upgrading the IOS, but that is not working either.  I tried "boot system flash:asr1000rp1-advipservicesk9.03.02.00.S.151-1.S.bin" command, but that did not work.  I made sure the image was good using the "verify" command and made sure to set "config-register 0x2102".  After I do a wr me and reload the router I get the below errors. [code]

View 1 Replies View Related

Cisco Switching/Routing :: Cannot Get Out Of Rommon Mode 1760

Dec 10, 2011

I'm currently pursuing to take my CCNA and am currently studying for it, but have recently encountered a problem with one of my 1760 routers that I can not solve.Yesterday I went to boot up my router like normal, however when I went into hyperterminal I noticed the router was in Rommon mode. Thinking I could change the configuration registry, I tried to bypass the NVRAM by using confreg 0x2142. However this still causes the router to go into Rommon mode. I am getting an error that states that there is insufficient memory to load the IOS image. [code]
 
I have used the dir flash: command and can see the IOS image, and try to boot from it (boot flash:iosimagename) but it will still go back into rommon mode. I also just swapped the RAM from my other 1760 into this 1760 and it booted up and went into normal configuraiton mode without any issues. However, the other router now will not load it's IOS image and I get the exact same error.I'm at a loss here, and have searched to figure out where or how I can just wipe the router clean to try and start fresh, but cannot get out or Rommon mode. The only thing I can think of is that the RAM went bad since it wont boot up either machine.

View 1 Replies View Related

Cisco Switching/Routing :: 6503 Sup-2T Unable To Get Into ROMmon

Apr 11, 2013

I have an issue with a customers 6503 with Sup-2T cards, where we are locked out of the console due to an authentication configuration error. So tried several times to get the card into rommon, with no success.
 
Checking through the various documents on CCO I dont find any reference to rommon on this card, but do find information on using the CMP to support the supervisor. I logged into the CMP but couldn't find a way from there to do a password reccovery either.So, is the `normal' IOS rommon/password recovery method supported.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved