Cisco Switching/Routing :: Upgrade 6509-Chassis In VSS-Environment?
May 1, 2013
we have some pairs of 6509-VSS, which partially have old (no more officially supported) 6509-Chassis.All linecards in the VSS are the same (Sup 720-10GE-3C, 67XX).
We now bought some new 6509-E-Chassis and want to change the old chassis by the new ones in a ISSU manner, that means:
1. putting the partner, which chassis changes, in redundancy mode, switch it off, exchange chassis (old "Catalyst 6509", new "Catalyst 6509-E")
2. inserting the line-cards exactly in the same slots and connecting all cables
3. switch on the new chassis, witing to come up in VSS
I'm not sure of having to set the switch number for VSS (is that in the Sup?; configuration? or part of the chassis-memory?)
I've looked up cisco for some hints, but don't found anything.
View 5 Replies
ADVERTISEMENT
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
Dec 19, 2012
Currently have a pair of 6509 chassis setup with VSS. Only have the Sup and two line cards in each chassis. Would like to replace with a new pair of 6504E chassis. Is it possible to fail one chassis at a time and migrate to the new 6504E?
View 3 Replies
View Related
Mar 9, 2013
We have a backup sup 720 which has a 2 gigabit ethernet though port channel, to another chassis. Suddenly UDLD detected an error and got into err disable, then this err disable didn't let the interface set to DOWN, and created a switch loop, then our Supervisor reloaded. I'd like to know what could have caused this reload. In my opinion could have a been the switch loop, but also I've been checking from the output interpreter the show tech and might have been a bug, the only one that could match in IOS version 12.2(33)SXH, is this one: url...
We're going to disable err-disable next time I guess and recover the link manually, apart from that what could have made the sup for crash and reload?
View 4 Replies
View Related
Jan 28, 2012
swapping out a failed supervisor card on a 6509 chassis?
View 6 Replies
View Related
Oct 18, 2012
Are there any physical characteristic differences between the 6509 and 6509-E chassis?
View 4 Replies
View Related
Dec 9, 2012
I have multiple 6509 vss switch. and i notice when the standby chassis reboot I didn't get any snmp trap, but I got when the active one reboot. my question is is there any mib out there for detecting and got a trap when standby reboot?
View 2 Replies
View Related
Nov 29, 2010
I have a heck of a time finding this kind of information on the cisco site...Is the WS-SUP720-BASE line card a fully supported module in the 6509-E chassis?
View 4 Replies
View Related
Sep 25, 2012
Any have experience on triggered failover on VSS deployment with 1 VS-720-10G-3C in each chassis? I tried using "redundancy force-switchover" but after that the 20G VSL is flapping up & down and cannot be up normally, we got 1 FWSM in each chassis, any configuration need to fit in this kind deployment? BTW, if I shutdown the power source of VSS active chassis, both FWSM & VSS can failover normally.
View 3 Replies
View Related
May 15, 2013
setting up VRF-lite on redundant 6509-E chassis to account for chassis failure? Let's say I have 2x 6509-Es configured with HSRP for 2 vlans, ServerA and ServerB. So
6509-A#
!
interface Vlan10
description ServerA VLAN
ip address 10.10.10.2 255.255.255.0
ip flow ingress
standby 1 ip 10.10.10.1
standby 1 priority 105
[code].....
I now need to create an environment where the Server VLANs can be provided for two customers and they need to be wholly separate. On 6509-A, I make VRF CustomerA and VRF CustomerB and I assign Vlan10 to VRF CustomerA and Vlan20 to CustomerB. Do I create the SAME VRFs on 6509-B with the same logic?
View 1 Replies
View Related
Jul 1, 2012
We've just invested in a pair of Sup2Ts to upgrade a Sup720 6509 chassis but I'm unsure exactly how the management port(s), aka the Connectivity Management Processor (CMP), should be configured (and patched) in a dual supervisor system?Is each CMP an independent entity or is the management interface configuration (IP address, gateway, etc) replicated between supervisors?If it's the latter then do both management ports need to be physically connected at the same time?
View 1 Replies
View Related
Apr 28, 2013
We recently purchased 2 Cisco 6500 series switches (with Sup 2T). These switches will be replacing our old 2 6500 series switches (with Sup 720).
We have 70 vlans and 90+ closet switches (2900) connecting the core switches We have 2 WLC connected to the core switch. We also have a 1 x 1 connection to a VSS switch which in turn connects to our Server Co-Location data center utilizing IPSec & GRE tunnel to connect to our Server Co-Location data center.
Our routing protocol is EIGRP. Our VTP domain at Server Co-Location is separate from our location “A” campus. I was wondering what is the best way to migrate our Core switches at location “A” campus.
The requirement is we would like to replace these switches with minimum downtime.
View 6 Replies
View Related
Feb 7, 2012
The 6509 Series Switches support the scenario VSS Active-Active Chassis, I would like to setup both switch's as one virtual switch but working at the same time, not with Active - Stand By Chassis.
My plans it to create PortChannel accross both Switches 6509 in order to have 2 links one connected to one slot/switch and the other connected to slot/switch in the second 6509 for servers redundancy.
View 1 Replies
View Related
May 15, 2012
we need to install a line cards (WS-X4548-GB-RJ45, chassis WS-C4510R-E), on a chassis Ws-6504-E.where I can find information about compatibility?
View 2 Replies
View Related
May 15, 2012
Tonight we were performing an IOS upgrade on our 6509 VSS to 122-33.SXI6. Both 6509's have dual Supervisor cards installed. Initially we had problems with switch 2 slot 5 supervisor returning to rommon however switch 2 slot 6 supervisor loaded correctly. After manually setting the boot var in rommon, switch 2 slot 5 supervisor reloaded correctly.
After all supervisor's were online we noticed when looking at " show switch virtual redundancy" that sw 1 & 2 slot 6 supervisors were running the correct IOS version but sw 1 & 2 slot 5 were running different IOS versions, however when looking at the show version we are running on the upgraded IOS??? See output below...
Why the active supervisor has loaded the incorrect IOS the VSS is running on the upgraded IOS? I have verified the IOS was copied correctly to each supervisor bootdisk, I see no issues.
My Switch Id = 1 Peer Switch Id = 2 Last switchover reason = none Configured Redundancy Mode = sso Operating Redundancy Mode = sso
Switch 1 Slot 5 Processor Information :----------------------------------------------- Current Software state = ACTIVE Uptime in current state = 3 hours, 38 minutes Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)Technical Support:
[code].....
View 3 Replies
View Related
Jan 15, 2012
Will I be OK doing a eFSU Upgrade from s72033-ipservicesk9_wan-mz.122-33.SXI2a to s72033-ipservicesk9_wan-mz.122-33.SXJ1?
I only have a single supervisor in each chassis.
Should I be ok with just following the eFSU upgrade instructions in the below?
[URL]
View 1 Replies
View Related
Jan 9, 2013
I am going to upgrade the IOS image on 6509-E SUP 2T from 15.1 to s2t54-adventerprisek9-mz.SPA.150-1.SY3.bin switch and i would like to know whether i would need to upgrade the boot loader image as well.
View 4 Replies
View Related
Sep 9, 2012
I have a 6509 switch with SSO Redundancy (STANDBY HOT) with IOS ver 12.2(17d)SXB11, RELEASE SOFTWARE (fc1) (c6k222-jk9sv-mz.122-17d.SXB11.bin). I need to upgrade the IOS on this switch.I have 512MB Memory on the switch and 40144896 bytes free on Disk0.which IOS is the latest version to upgrade and also give me some hints for IOS upgrade on this switch?
View 7 Replies
View Related
May 14, 2013
I would like to find out how to upgrade SUP engine 32 via USB port as I've never did IOS upgrade on a SUP engine via USB before
View 5 Replies
View Related
Nov 19, 2012
I have 2 6509 switches configured with VSS.As per advised my managment I have to enable SSH but it is not available existing IOS which is "s72033-ipbase-z.122-33.SXI3.bin". SSH available in "s72033-ipbasek9-mz.122-33.SXI10".
upgrade the IOS with VSS configured switches.
View 9 Replies
View Related
Oct 16, 2012
We are trying to upgrade the IOS on one of our 6509 switches. We have two 720 10GE supervisors running in SSO. Our procedure is reload the standby supervisor with the new IOS. We understand that you can only use one console connection when in RPR mode so we rely on the active supervisor giving us information that the standby unit is up and running.
The problem we have is that when we do a "show Module" on the switch the online diagnostics for the standby supervisor comes back us unknown. [code] We believe the active supervisor can see the standby supervisor because when we save the configuration we get a message saying that the config is sync'd with the standby router. We have a TAC case raised to investigate. We are upgrading from 12.2(33) SXI1 to 12.2(33) SXJ3
View 1 Replies
View Related
Jan 22, 2013
I am planning on upgrading my 6509s to use VSS within the next few weeks. I have checked all of the hardware and software prerequisites, and we are good to go from that perspective.I do have more of a procedural question- my switches are already configured and in production, VLANs, HSRP (3 IP addresses per VLAN- 1 per switch plus virtual IP), etc. Does the VSS upgrade take all of this into account and rewrite the configuration correctly, or should I plan on redoing the entire config for the switches after the upgrade?
View 6 Replies
View Related
Oct 8, 2012
We are planning to upgrade the IOS on our two 6509E supervisors in the next few weeks. We currently run IOS 12.2(33) SXI1 and are upgrading to 12.2(33) SXJ3. At the moment the two supervisors are in SSO mode and after reading many articles it says that when the images are different on the two supervisors they are in RPR mode. When you then reload the active supervisor it will reboot all the line cards.
1. Is above correct? Will my line card reload?
2. We also have a FWSM installed, When/If the line cards are rebooted does the FWSM also reboot?
View 1 Replies
View Related
Sep 18, 2012
I am going to upgarde SUP2 to SUP32 on my 6509 by next week. right now I have 2 SUPs on the 6509 in redundant mode.
View 5 Replies
View Related
Dec 12, 2012
I have ROM MON version 12.2(17r)S2 and I am trying to determine if I need to chnage this to 12.2(17r)SX7. It does not appear I need to with the upgrade to 12.2(33)SXI10. Is this correct?
View 1 Replies
View Related
Oct 7, 2012
I need to upgrade 2xsup2 module to 2xsup32 on my cisco 6509. I just found out that I can not have the CISCO WS-X6500-SFM(Cisco Switch Fabric Module switch) with Sup32 and I have to remove 2 xCISCO WS-X6500-SFM2 modules from the switch.I am using this switch as a access switch and most of the ports are 100Mbps.
let me know if the upgrade would be safe or not as far as the bandwidth?
View 2 Replies
View Related
Jun 21, 2012
I support an active VSS cluster using 2 x 6509E chassis with single Supervisor 3C modules in each chassis. I want to replace these with Supervisor 2T modules. All my service modules and line cards are supported with the Sup2Ts (I will also be implementing 6908 modules). Is there a document on the Cisco site for this? I haven't found one though I can find plenty that describe how to do a software upgrade.
(Note, I have a 3rd (non VSS) 6509E chassis that is also part of this core network and that will maintain VTP/V LAN's etc).
View 9 Replies
View Related
Sep 30, 2012
I have 2 6509 chasis with one SUP720-3B in each and current IOS is s72033-ipservicesk9_wan-mz.122-18.SXF4 and 2 FWSM with version is 3.3.1 I need to upgrade FWSM system software to 4.1, after checking FWSM 4.1 release notes, I thought of upgrading IOS to latest version to 12.2(33)SXJ.I got new 2 CF of 512MB and downloaded the new IOS on them and need to upgrade 6509 IOS first to meet the requirement for FWSM upgrade.
View 1 Replies
View Related
Feb 2, 2013
I am planning to upgrade the current core switch(3750) to 6509 series switch. Since we have a production network running we have to plan for an online core switch upgrade.
View 7 Replies
View Related
Nov 15, 2012
I have 1x Cisco 6509 with Sup2 and MSFC2 and it is running on IOS (c6k222-jk9sv-mz.122-17d.SXB11). I have following policy map :
Policy Map VOIP
Class IP PHONE
priority percent 75
and the following command on each interface: service-policy output VOIP those configuration are working fine on SUP2 with MSFC2 but last week I tried to upgrade the SUP2 to SUP32 on the switch and upgrade the IOS to the latest version (s3223-adventerprisek9-mz.122-33.SXJ4) but when I try to put service-policy output VOIP on each physical interface I am getting the following error:
"Priority command is not supported in output direction for this interface" and when I try to add service-policy output VOIP on a V LAN interface I am getting following error:
MQC features are not supported in output direction for this interface. Will I need to change something after upgrading to SUP32..
View 3 Replies
View Related
May 29, 2012
Does the FWSM for a 6506/6509 is supported in a VSS environment?Also, does the FWSM work with the 2T supervisor module?
View 1 Replies
View Related
Feb 29, 2012
Need to remove the IPSec VPN SPA module from the 6509 chassis. Does the module is hot swappable or does the 6509 need to be turned off prior to removal.
View 2 Replies
View Related
