Cisco Switching/Routing :: 6500 - Upgrade From SUP720 To SUP2T With New Chassis?
Apr 28, 2013
We recently purchased 2 Cisco 6500 series switches (with Sup 2T). These switches will be replacing our old 2 6500 series switches (with Sup 720).
We have 70 vlans and 90+ closet switches (2900) connecting the core switches We have 2 WLC connected to the core switch. We also have a 1 x 1 connection to a VSS switch which in turn connects to our Server Co-Location data center utilizing IPSec & GRE tunnel to connect to our Server Co-Location data center.
Our routing protocol is EIGRP. Our VTP domain at Server Co-Location is separate from our location “A” campus. I was wondering what is the best way to migrate our Core switches at location “A” campus.
The requirement is we would like to replace these switches with minimum downtime.
View 6 Replies
ADVERTISEMENT
Jul 1, 2012
We've just invested in a pair of Sup2Ts to upgrade a Sup720 6509 chassis but I'm unsure exactly how the management port(s), aka the Connectivity Management Processor (CMP), should be configured (and patched) in a dual supervisor system?Is each CMP an independent entity or is the management interface configuration (IP address, gateway, etc) replicated between supervisors?If it's the latter then do both management ports need to be physically connected at the same time?
View 1 Replies
View Related
Jun 21, 2012
I support an active VSS cluster using 2 x 6509E chassis with single Supervisor 3C modules in each chassis. I want to replace these with Supervisor 2T modules. All my service modules and line cards are supported with the Sup2Ts (I will also be implementing 6908 modules). Is there a document on the Cisco site for this? I haven't found one though I can find plenty that describe how to do a software upgrade.
(Note, I have a 3rd (non VSS) 6509E chassis that is also part of this core network and that will maintain VTP/V LAN's etc).
View 9 Replies
View Related
Jun 4, 2013
I am trying to upgrade Sup2T from 15.0 to 15.1 (same feature sets). I have the new image in bootflash and have changed the boot system statement to boot from the new image and the config register is 0x2102. However, everytime it reboots it loads the old image. [code]
View 4 Replies
View Related
Nov 29, 2010
I have a heck of a time finding this kind of information on the cisco site...Is the WS-SUP720-BASE line card a fully supported module in the 6509-E chassis?
View 4 Replies
View Related
Aug 9, 2012
Cisco 6500 with 2T supervisor engine with following software Cisco IOS Software, s2t54 Software (s2t54-IPSERVICESK9-M), Version 15.0(1)SY1, RELEASE SOFTWARE (fc4)
The problem is that, I am not able to configure Multilayer Switching (MLS) (mls rp ip) in the global config command. Although the "mls" is visible on the config menu. but when I say "mls ?", the router prompt "unrecognize command"
Not sure if SUP 2T support MLS or it come with different name.
View 1 Replies
View Related
Aug 4, 2012
I'm configuring VSS with two Sup2T but the Sup2T of the standby not coming active
View 6 Replies
View Related
Apr 22, 2013
I am migrating services from SUP720-3B to VS-SUP2T-10G= and moving to a VSS configuration between a pair of Cat6506 distribution layer switches. I need to enable QoS on these switches, primarily to trust dscp and also to prioritise voice traffic. The autoqos feature works for some ports but does not work on port-channel interfaces and port-channel member interfaces. How can I apply the qos settings for these interfaces in line with what auto qos would normally provide. My line cards are as follows:
Civic_6506VSS#sho mod
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE
[Code].....
View 1 Replies
View Related
Sep 11, 2012
when using "show mls statistics" I see a lot packets are getting L3 Processed. Does that mean they are getting software-forwarded?
IOS is 12.2(33)SXI5.
Cat6k#show mls statistics
Statistics for Earl in Module 5
L2 Forwarding Engine
[Code]....
View 1 Replies
View Related
Nov 16, 2011
I have problem with the standby supervisor in 6500 vss and need to replace the supervisor. I have follow how-to on the cisco web site url...
But when i boot the new standby sup720 it comes active and both supervisors is rebooting. I wonder if i can do the replacement without rebooting both active and standy supervisor.
View 1 Replies
View Related
Aug 22, 2012
We are preparing to install a new switching Infrastructure at one of our sites. We have decided that we want to have two separate chassis as a core. My original idea was to purchase 2 - 4500 chassis and install 10Gb and 1GB line cards in each and use STP and HSRP to load balance between the two cores.
We had also contacted a vendor for thier recommendations and they came back with 2 6500 Chassis running VSS. I reviewed what VSS was as I had never heard of it and it looks to me basically to be real close to the same thing as Stacking. I didn't really want to have stacked Cores because I would like to have the flexibility to be able to take one core out and update the software or image, reboot, and such without effecting anything on the network. I can do that with the non-VSS approach but it looks like that would be more of a problem with VSS.
My question is, how to use VSS with the 6500's? How to take one of the VSS pairs off line and not effect normal network operations?
View 7 Replies
View Related
Jan 24, 2007
if it is possible to recover a Cat 6500 that has no code on bootflash from ROMMON, and is it mandatory to have a compact flash card to do the recovery ? or can one use xmodem or TFTP ?
View 6 Replies
View Related
Nov 21, 2011
I will be installing a secondary SUP720 in a 6509-E and will be upgrading the IOS on the existing SUP which is on 122-18.SXF6. I've read that this release has passed End of Critical Maintenance earlier this you. I thinking of upgrading the IOS to 12.2.33-SXJ1(ED) or 12.2.33-SXI8(ED) (possible more stable), but i'm not sure if i need any step upgrades from the current version. The SUP meets the required hardware specs and I will also be upgrading the ROMMON to 12.2(17r)SX7 first.
I have alot of experience upgrading IOS on routers and switches, but i just need to now if there are any gotchas that i need to know for the upgrade on the SUP.
The other issue is i don't believe the current IOS has been installed, are there any issue running on an IOS not installed. Patching is not available since the system is not running from an installed image. To install please use the "install file" command.
View 3 Replies
View Related
Dec 8, 2011
I have 2x v10000 Websense Security Gateways that are connected to 2x 6500 SUP720. When I turn on cluster management function between Websense appliance, they speak to each other only if they are connected in the same 6500. When they are connected one in every 6500 cluster management does not work. They are connected on the same physical vlan. Do I need multicast to be configured in the 6500 switches?
View 5 Replies
View Related
Jul 4, 2012
migration of an existing Sup720 configuration to a new Sup2T. At present we have a Sup2T chassis in the lab running 15.0(1)SY1 and a production Sup720 chassis running 12.2(33)SXI5.I've taken a copy of the production startup-config, renamed it to 'startup-config-BGFL_6509_MBAS-020712' and copied it to the bootdisk (and slave bootdisk) of the new Sup2Ts.I've then added the command 'boot config bootdisk:startup-config-BGFL_6509_MBAS-020712' in an attempt to boot from that config and have the Sup2T migrate it to the new config standards (particularly from a QoS perspective as mentioned here :[URL]
!
boot-start-marker
boot system flash bootflash:s2t54-advipservicesk9-mz.SPA.150-1.SY1.bin
boot config bootdisk:startup-config-BGFL_6509_MBAS-020712
...
Router#sh bootvar
BOOT variable = bootflash:s2t54-advipservicesk9-mz.SPA.150-1.SY1.bin,1;
[code]....
View 5 Replies
View Related
Sep 26, 2012
I came across this Multichassis EtherChannel Features when read about information from Cisco Smart Business Architecture.After checking further, knowing that Cataly stwitch 6500 supports this feature.provide information that beside Catalyst 6500, is there any other model of Catalyst switch can support this feature?
View 4 Replies
View Related
May 1, 2013
we have some pairs of 6509-VSS, which partially have old (no more officially supported) 6509-Chassis.All linecards in the VSS are the same (Sup 720-10GE-3C, 67XX).
We now bought some new 6509-E-Chassis and want to change the old chassis by the new ones in a ISSU manner, that means:
1. putting the partner, which chassis changes, in redundancy mode, switch it off, exchange chassis (old "Catalyst 6509", new "Catalyst 6509-E")
2. inserting the line-cards exactly in the same slots and connecting all cables
3. switch on the new chassis, witing to come up in VSS
I'm not sure of having to set the switch number for VSS (is that in the Sup?; configuration? or part of the chassis-memory?)
I've looked up cisco for some hints, but don't found anything.
View 5 Replies
View Related
Dec 21, 2011
how can we upgrade 6500 non modular ios to normal 6500 ios?
View 5 Replies
View Related
Mar 25, 2012
I faced with problem while i was attemping to upgrade CISCO7606 (R7000) from 12.2(33)SRE1 to 12.2(33)SRE6.
rommon 2 > boot c7600s72033-advipservices-mz.122-33.SRE6.bin
Loading image, please wait ...
Invalid device specified
Booting from default device
Initializing ATA monitor library...
string is bootdisk:c7600s72033-advipservices-mz.122-33.SRE1.bin
[code].....
View 3 Replies
View Related
May 15, 2012
we need to install a line cards (WS-X4548-GB-RJ45, chassis WS-C4510R-E), on a chassis Ws-6504-E.where I can find information about compatibility?
View 2 Replies
View Related
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
Mar 25, 2012
how to upgrade IOS in switch 6500 connect in VSS from 12.2(33)SXI IOS to 12.2(33)SXJ?
View 3 Replies
View Related
May 21, 2012
I have WS-C6509-E chassis with VS-S2T-10G supervisor.
Currently I have IOS " S2TIBK9-15001SY - Cisco CAT6000-VS-S2T IOS IP BASE FULL ENCRYPT "
Can I upgrade the IOS to " S2TISK9-15001SY - Cisco CAT6000-VS-S2T IOS IP SERV FULL ENCRYPT " without purchasing this IOS?
Will I face issue in TAC cases?
View 1 Replies
View Related
May 1, 2013
we have a customer who needs to perform upgrade on their Core 6500 Switch IOS from version 12.2(17d)SXB11a to 15.1SY.Is this a supported upgrade path and can it be done directly?
View 11 Replies
View Related
Apr 15, 2013
Today we have 2 VSS, and are about to buy another two 6500 chassies to bulid a new VSS. Our currens chassies have supervisor 720, and the new one will probably have SUP2T
We have a network design that allowes us to run on a single chassie per VSS if we have hardware failure. This means that in a really worst case scenario we need to move around hardware to have 3 system up and running (that would mean multiple failures on all systems... so really really worst case scenario )
So here is my first question. Can I run a VSS with different supervisors in the chassies? Second question: If I want to upgrade a VSS from SUP720 to SUP2T, cna I run 2 supervisors per chassie (quad supervisor VSS) where one supervisor is SUP720 and one is SUP2T?
View 7 Replies
View Related
Apr 29, 2012
Doing a bug scrub on our dual core, dual Sup 720 6500s tonight. We are going from s72033-advipservicesk9_wan-mz.122-33.SXI4a.bin to SXI9. I want to get a second set of eyes on my script since I have not done this for about 1 1/2 years. Following this doc:[URL]
Script:
Backup
sh ver
remote command switch show version
[Code].....
View 6 Replies
View Related
Apr 11, 2012
My task is to upgrade a couple of 6500 series switches, 6513 with SUP720/MSFC3 (WS-SUP720) and Policy Feature Card 3 (WS-F6K-PFC3B) installed. How to upgrade those switches if in SSO redundancy mode with two SUPs installed?
I understand that it is good to connect to the MSFC3 via console and upgrade this first, is this correct?
I also have to upgrade some 6509 but I only can test it on one 6509-E, how to get everything up to date. [code]
View 1 Replies
View Related
Jan 15, 2013
Have a new 6509-E router with 2 sup2T blades. However it came with IPbase and we need to put Ipservices on it. I have copied ipservices IOS to bootdisk and slavebootdisk.
However I cannot get get to the boot command to point to bootdisk. It only allows me to point to flash:
)#boot system flash ?
WORD System image filename
<cr>
Yet I don't seem to have an option to copy this new IOS to flash. How do I get to copy it to flash:
Here is the original show boot command:
sh boot
BOOT variable = bootflash:s2t54-ipbasek9_npe-mz.SPA.150-1.SY1.bin,1;
CONFIG_FILE variable =
[Code].....
View 1 Replies
View Related
Dec 10, 2012
I have a 6509 witch a sup vs-Sup2T, and I´m very confuse for to configure QoS. is diferent in the old supervisor..What is the command similar to map cos to DSCP.. look
This is a configuration in a sw 4507
qos map dscp 56 to tx-queue 1
qos map cos 1 to dscp 10
qos map cos 2 to dscp 18
qos map cos 3 to dscp 26
qos map cos 4 to dscp 34
qos map cos 5 to dscp 46
qos
In 6509 with sup2T and version 15.0.SY2 Im no sure.. I see two command
platform qos map cos-mutation testmap 4 5 6 7 0 1 2 3
and
table-map cos-discard-class-map 0 1 2 3 4 5 6 7
View 1 Replies
View Related
Jun 4, 2013
Are there any best practices for preventative maintenance on Catalyst Chassis switches. Looking to build a PMI schedule for a customer. Or is there evidence not to perform it at all. Things like re-seating line cards, cleaning fan exhausts, etc.
View 1 Replies
View Related
Jan 28, 2013
Is there any challenge to upgrade core switch 6500 series from Nexus 7009 which runs NxOS, because i have 3750X series switches connected at distribution and access layer in my network topology??
Is there any challenge if we place NxOS in core and IOS in distribution and Access layer??? how we are able to match sh run config in existing 6500 switch to Nexus 7009 NXOS?
View 9 Replies
View Related
Dec 9, 2012
We are planning to implement the 6509-E with two Sup 2Ts and a few 48 ports switches. We also want to make this the router for our network and replace the 7206VRX.
View 5 Replies
View Related
