Cisco Switching/Routing :: Upgrade 6500 Sup2T From 15.0 To 15.1

Jun 4, 2013

I am trying to upgrade Sup2T from 15.0 to 15.1 (same feature sets).  I have the new  image in bootflash and have changed the boot system statement to boot from the new image and the config register is 0x2102.  However, everytime it reboots it loads the old image. [code]

View 4 Replies


ADVERTISEMENT

Cisco Switching/Routing :: 6500 - Upgrade From SUP720 To SUP2T With New Chassis?

Apr 28, 2013

We recently purchased 2 Cisco 6500 series switches (with Sup 2T). These switches will be replacing our old 2 6500 series switches (with Sup 720).
 
We have 70 vlans and 90+ closet switches (2900) connecting the core switches We have 2 WLC connected to the core switch. We also have a 1 x 1 connection to a VSS switch which in turn connects to our Server Co-Location data center utilizing IPSec & GRE tunnel to connect to our Server Co-Location data center.
 
Our routing protocol is EIGRP. Our VTP domain at Server Co-Location is separate from our location “A” campus. I was wondering what is the best way to migrate our Core switches at location “A” campus.
 
The requirement is we would like to replace these switches with minimum downtime.

View 6 Replies View Related

Cisco Switching/Routing :: MLS On 6500 With Sup2T

Aug 9, 2012

Cisco 6500 with 2T supervisor engine with following software Cisco IOS Software, s2t54 Software (s2t54-IPSERVICESK9-M), Version 15.0(1)SY1, RELEASE SOFTWARE (fc4)
 
The problem is that, I am not able to configure Multilayer Switching (MLS) (mls rp ip) in the global config command. Although the "mls" is visible on the config menu. but when I say "mls ?", the router prompt "unrecognize command"
 
Not sure if SUP 2T support MLS or it come with different name.

View 1 Replies View Related

Cisco Switching/Routing :: 6500 - Configuring VSS With Two Sup2T?

Aug 4, 2012

I'm configuring VSS with two Sup2T but the Sup2T of the standby not coming active

View 6 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 VS-SUP2T-10G QoS Configuration

Apr 22, 2013

I am migrating services from SUP720-3B to VS-SUP2T-10G= and moving to a VSS configuration  between a pair of Cat6506 distribution layer switches. I need to enable QoS on these switches, primarily to trust dscp and also to prioritise voice traffic. The autoqos feature works for some ports but does not work on port-channel interfaces and port-channel member interfaces. How can I apply the qos settings for these interfaces in line with what auto qos would normally provide. My line cards are as follows:
 
Civic_6506VSS#sho mod
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
1    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE   

[Code].....

View 1 Replies View Related

Cisco Switching/Routing :: 6509 - Upgrade Sup720 To Sup2T In VSS Cluster

Jun 21, 2012

I support an active VSS cluster using 2 x 6509E chassis with single Supervisor 3C modules in each chassis. I want to replace these with Supervisor 2T modules. All my service modules and line cards are supported with the Sup2Ts (I will also be implementing 6908 modules). Is there a document on the Cisco site for this? I haven't found one though I can find plenty that describe how to do a software upgrade.
 
(Note, I have a 3rd (non VSS) 6509E chassis that is also part of this core network and that will maintain VTP/V LAN's etc).

View 9 Replies View Related

Cisco Switching/Routing :: Upgrade 6500 Non Modular IOS To Normal 6500?

Dec 21, 2011

how can we upgrade 6500 non modular ios to normal 6500 ios?

View 5 Replies View Related

Cisco Switching/Routing :: Upgrade IOS In 6500 VSS?

Mar 25, 2012

how to upgrade IOS in switch 6500 connect in VSS from 12.2(33)SXI IOS to 12.2(33)SXJ?

View 3 Replies View Related

Cisco Switching/Routing :: Upgrade IOS In 6500 SUP 2T

May 21, 2012

I have WS-C6509-E chassis with VS-S2T-10G supervisor.

Currently I have IOS " S2TIBK9-15001SY - Cisco CAT6000-VS-S2T IOS IP BASE FULL ENCRYPT "

Can I upgrade the IOS to " S2TISK9-15001SY - Cisco CAT6000-VS-S2T IOS IP SERV FULL ENCRYPT " without purchasing this IOS?

Will I face issue in TAC cases?

View 1 Replies View Related

Cisco Switching/Routing :: Upgrade 6500 IOS 12.2(17d)SXB11a To 15.1SY?

May 1, 2013

we have a customer who needs to perform upgrade on their Core 6500 Switch IOS from version 12.2(17d)SXB11a to 15.1SY.Is this a supported upgrade path and can it be done directly?

View 11 Replies View Related

Cisco Switching/Routing :: Upgrade Supervisors In 6500 VSS

Apr 15, 2013

Today we have 2 VSS, and are about to buy another two 6500 chassies to bulid a new VSS. Our currens chassies have supervisor 720, and the new one will probably have SUP2T
 
We have a network design that allowes us to run on a single chassie per VSS if we have hardware failure. This means that in a really worst case scenario we need to move around hardware to have 3 system up and running (that would mean multiple failures on all systems... so really really worst case scenario )
 
So here is my first question. Can I run a VSS with different supervisors in the chassies? Second question: If I want to upgrade a VSS from SUP720 to SUP2T, cna I run 2 supervisors per chassie (quad supervisor VSS) where one supervisor is SUP720 and one is SUP2T?

View 7 Replies View Related

Cisco Switching/Routing :: Dual Core / SUP 720 6500 IOS Upgrade?

Apr 29, 2012

Doing a bug scrub on our dual core, dual Sup 720 6500s tonight. We are going from s72033-advipservicesk9_wan-mz.122-33.SXI4a.bin to SXI9. I want to get a second set of eyes on my script since I have not done this for about 1 1/2 years. Following this doc:[URL]  
 
Script:
 
Backup
sh ver
remote command switch show version

[Code].....

View 6 Replies View Related

Cisco Switching/Routing :: Upgrade Couple Of 6500 Series Switches

Apr 11, 2012

My task is to upgrade a couple of 6500 series switches, 6513 with SUP720/MSFC3 (WS-SUP720) and Policy Feature Card 3 (WS-F6K-PFC3B) installed. How to upgrade those switches if in SSO redundancy mode with two SUPs installed?
 
I understand that it is good to connect to the MSFC3 via console and upgrade this first, is this correct?
 
I also have to upgrade some 6509 but I only can test it on one 6509-E, how to get everything up to date. [code]

View 1 Replies View Related

Cisco WAN :: 6509 - How To Upgrade IOS On SUP2T

Jan 15, 2013

Have a new 6509-E router with 2 sup2T blades. However it came with IPbase and we need to put Ipservices on it. I have copied ipservices IOS to bootdisk and slavebootdisk.
 
However I cannot get get to the boot command to point to bootdisk. It only allows me to point to flash:
 
)#boot system flash ?
WORD  System image filename
<cr>
 
Yet I don't seem to have an option to copy this new IOS to flash. How do I get to copy it to flash:
 
Here is the original show boot command:
 
sh boot
BOOT variable = bootflash:s2t54-ipbasek9_npe-mz.SPA.150-1.SY1.bin,1;
CONFIG_FILE variable =

[Code].....

View 1 Replies View Related

Cisco Switching/Routing :: Command QoS In VS-Sup2T Of 6509

Dec 10, 2012

I have a 6509 witch a sup vs-Sup2T,  and I´m very confuse for to configure QoS. is diferent in the old supervisor..What is the command similar to map cos to DSCP..  look
 
This is a configuration in a sw 4507
 
qos map dscp 56 to tx-queue 1
qos map cos 1 to dscp 10
qos map cos 2 to dscp 18
qos map cos 3 to dscp 26
qos map cos 4 to dscp 34
qos map cos 5 to dscp 46
qos
  
In 6509 with sup2T and version 15.0.SY2  Im no sure.. I see two command
 
platform qos map cos-mutation testmap 4 5 6 7 0 1 2 3  
and 
table-map cos-discard-class-map 0 1 2 3 4 5 6 7  

View 1 Replies View Related

Cisco Switching/Routing :: Any Challenge To Upgrade Core Switch 6500 Series From Nexus 7009 Which Runs NxOS

Jan 28, 2013

Is there any challenge to upgrade core switch 6500 series from Nexus 7009 which runs NxOS, because i have 3750X series switches connected at distribution and access layer in my network topology??
 
Is there any challenge if we place NxOS in core and IOS in distribution and Access layer??? how we are able to match sh run config in existing 6500 switch to Nexus 7009 NXOS?

View 9 Replies View Related

Cisco Switching/Routing :: Replacing 7206VRX With 6509-E Sup2T?

Dec 9, 2012

We are planning to implement the 6509-E with two Sup 2Ts and a few 48 ports switches. We also want to make this the router for our network and replace the 7206VRX.

View 5 Replies View Related

Cisco Switching/Routing :: 6506E SUP2T QOS Channel Consistency

May 21, 2012

I have a catalyst 6506E (WS-C6506-E) with a SUP2T supervisor (VS-S2T-10G) card and a 10G interface card (WS-X6816-10G-2T) + DFC4.I have configured an etherchannel to another switch with the 2 10Giga ports of the SUP2T card and 2 10giga ports of the interface card.I only use the 10Giga ports of the SUP2T card so the cards have the same QOS transmit capabilities.But they do not have the same receive capabilities.
 
So when I configure QOS (with the new commands on SUP2T) on my 4 ports within the Etherchannel, 2 ports move down because of the inconsistency.
Till this point, no surprise.
 
The problem is that the command "no platform qos channel consistency" replacing the "no mls qos channel-consistency" does not exist.I run the last IOS 12.2(50)SY1 IPSERVICESK9.
 
And I cannot have QOS on my Etherchannel on the 2 cards.Or I have to use 4 ports of my interface card but in case of failure of this card, I loose the whole etherchannel.I there a way to avoid the consistency check ?

View 2 Replies View Related

Cisco Switching/Routing :: 3750X - Connect C3KX-NM-10G To X2 10G Port On Sup2t In 6500E?

Mar 17, 2013

Is it possible to connect 3750X with C3KX-NM-10G to X2 10G port on sup2t in 6500E switch.There is Cisco OneX Converter Module, but I could not find that it is supported on sup2t.

View 2 Replies View Related

Cisco WAN :: Upgrade Sup720 6509 Chassis - Configure Sup2T Management Ports?

Jul 1, 2012

We've just invested in a pair of Sup2Ts to upgrade a Sup720 6509 chassis but I'm unsure exactly how the management port(s), aka the Connectivity Management Processor (CMP), should be configured (and patched) in a dual supervisor system?Is each CMP an independent entity or is the management interface configuration (IP address, gateway, etc) replicated between supervisors?If it's the latter then do both management ports need to be physically connected at the same time?

View 1 Replies View Related

Cisco Switching/Routing :: 6500 Switching Fabric Bandwidth 720 Is Calculated?

Jan 21, 2012

As per my understanding 6509 all slots are dual channel, so 9 slot * 40 per slot (20 g in and 20 g out) = 360 GB How cisco claim the 720 ?? What about the 6513 chassic switch fabric connection?

View 5 Replies View Related

Cisco Switching/Routing :: 6500 / High Switching Processor Utilization?

Sep 20, 2012

I am seeing a strange situation on my 6500 switch?By having snmp walk on '1.3.6.1.4.1.9.9.109.1.1.1.1.3' (== cpmCPUTotal5sec), I came to know that there are two processor and the cpu util for switching processor is gone to 88 % and some time creeps to 99 %.
 
snmpwalk -v2c -c "removes"  sw6500 '1.3.6.1.4.1.9.9.109.1.1.1.1.3'
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.1 = Gauge32: 12 (--- this is for CPU of Router Processor )
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.3 = Gauge32: 99 (--- this is for CPU of Switching Processor )
 
but when I do sh process cpu on the console, all looks normal as it shows cpu utilization of RP.  why the value is so high on the switching processor ?

View 1 Replies View Related

Cisco Switching/Routing :: IP Routing On 6500 Series Versus 3750?

Jan 24, 2013

For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?

View 1 Replies View Related

Cisco Switching/Routing :: 6500 / Restricting Inter-VLAN Routing?

May 9, 2013

I'm looking to restrict Inter-VLAN routing through L3 switch (cisco 6500) and wanted to know best possible way to do it. I used VACL and achieved success to some extent, but my config is making clients take up to 5-6 mins to authenticate IP address from the DNS (bootps).My VACL config was as follows:
 
Subnet to restrict is 10.100.15.0 (VLAN 15)
 STEP 1: Created extended ACL to allow bootpc/bootps through DNS
ip access-list extended EACL_DNS
permit udp any eq bootps any
permit udp any eq bootpc any
 
STEP 2: Created standard ACLs to allow only relevant subnet, server VLANs & some IPs from other subnets for printers/scanners etc.

ip access-list standard SACL_VLAN_15
permit 10.100.15.0 0.0.0.255 (the subnet I'm restricting)
permit 10.100.50.0 0.0.0.255 (server VLANs)
permit 10.100.25.45 0.0.0.0 (printer in another VLAN which has to have access in VLAN 15)
 
STEP 3: Created VLAN access list

vlan access-map VACL_15 10
match ip address EACL_DNS
action forward
 vlan access-map VACL_15 20
match ip address SACL_15
action forward
 
STEP 4: Applying VLAN Access list on VLAN 15 vlan filter VACL_15 vlan-list 15 Though the above works, below is noted:

1. I'm still able to PING 10.100.15.2 (the switch virtual interface) from outside the subnet, which I don't intend to do so. Howeve all cients in the subnet have no connectivity from outside the VLAN 15.
 
2. As mentioned its taking quiet some time to negotiate with the DNS server at system boot time.

View 3 Replies View Related

Cisco Switching/Routing :: 6500 MSFC No IP Routing Command

Jun 2, 2012

I used to "ip routing" command in order to enable inter-vlan routing, for example with 3750 cisco. I have a 6503 cisco with SUP720 MSFC3. I was able to create some vlans but I can not configure inter-vlan routing.
 
sw#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
swsur(config)#ip routing

[Code]....

View 3 Replies View Related

Cisco Switching/Routing :: IP Routing On 6500 Series Vs 3750?

Oct 30, 2011

For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?hes, do we need to enable the "ip routing" command manually for intervlan routing?

View 2 Replies View Related

Cisco Switching/Routing :: IP Routing Command In 6500?

Mar 16, 2013

Where is the "ip routing" command in Cisco switch 6500  series?

is the ip routing enable by default accoridng to the: [URL]

View 3 Replies View Related

Cisco Switching/Routing :: Difference Between 6500 SXJ And SXI?

Nov 25, 2011

i would like to check out what's the difference between the naming convnetion for the 6500 IOS.
 
I read the data sheet to support my POC deployment to support NCS v.1 the 6500 IOS need to upgrade to 12.2 (33) SXI
 
Is it able to work if i using SXJ instead of SXI, with the same IOS version 12.2 (33)?

View 3 Replies View Related

Cisco Switching/Routing :: TFT On 6500 Using Different Vlans And VRF

Jul 24, 2012

I have tried to test copy tftp: numerous time with no success.  I believe the reason it is failing is my laptop to Ethernet port is in vlan 62 and the tftp process operates in a different IP space.I am using gig 7/1 and configuring my laptop nic for x.x.x.254 mask 255.255.255.0.  I can ping from laptop to gateway) and I can ping from the switch to my laptop using ping vrf production x.x.x.254. Can you tell me what vlan I need to set my laptop connection in or if there is something else I need to change to make tftp work on vlan62?Does TFTP only work in vlan1 or can it be changed?

View 2 Replies View Related

Cisco Switching/Routing :: 6500 ACL Using QoS Not Working

Jul 16, 2012

We are setup like a hotel style workers camp.  We have wings full of rooms and residents with 3750 stacks in them.  Those switches connect back to our core 6500's.  The network is mostly all Layer 3, interfaces are routed with IPs.
 
When it was built before my time they included an ACL for each wing so that residents couldn't access internal devices (IE SSH to 6500) but I've come to notice it's not working.
 
I see hits on the ACL for accepts but nothing is hitting the deny rule at the top.Here is the configuration below:
 
mls qos aggregate-policer INTERNET1 24000000 80000 80000 conform-action transmit exceed-action drop
mls qos aggregate-policer INTERNET2 24000000 80000 80000 conform-action transmit exceed-action drop
mls qos aggregate-policer INTERNET 24000000 80000 80000 conform-action transmit exceed-action drop
[Code] ....

View 5 Replies View Related

Cisco Switching/Routing :: Does OTV Supported On Cat 6500

May 6, 2013

On googling I came across documents that say OTV (Overlay Transport Virtualization) is supported on Cat 6500. Any authentic information whether OTV is supported on Cat 6500, especially with Sup-720B? FYI, Cisco Feature Navigator does not mention it.

View 1 Replies View Related

Cisco Switching/Routing :: High CPU On 6500

Mar 19, 2012

SUP2T-D#sh proce cpu hist
    11111111111     1111     1111          1111    1111      
    0000000000099999000099999000099999999990000999900009999999
    0000000000099999000099999000099999999990000999900009999999
100 **********************************************************
90 **********************************************************
80 **********************************************************
70 **********************************************************
60 **********************************************************
50 **********************************************************
40 **********************************************************
30 **********************************************************
20 **********************************************************
10 **********************************************************
   0....5....1....1....2....2....3....3....4....4....5....5....
   0    5    0    5    0    5    0    5    0    5   
CPU% per second (last 60 seconds)

SUP2T-D#sh proce cpu sorted
CPU utilization for five seconds: 100%/83%; one minute: 99%; five minutes: 99%
PID Runtime(ms)   Invoked      uSecs   5Sec   1Min   5Min TTY Process
416     3324188    879928       3777 13.05% 14.42% 14.45%   0 Spanning Tree   
633      104408      5091      20508  1.50%  0.53%  0.45%   0 Env Poll        
  75       22000       298      73825  1.10%  0.13%  0.07%   0 Per-minute Jobs 
168       69696    163563        426  0.39%  0.23%  0.22%   0 slcp process    
   2         532      1010        526  0.07%  0.00%  0.00%   0 Load Meter      (code )

View 5 Replies View Related

Cisco Switching/Routing :: QOS On 6500 Switch?

Feb 17, 2013

I am trying to guarantee 100mbps for a vlan across a gig link.  I have done some research and found this command for switches
 
mls qos srr-queue input priority-queue 2 bandwidth 20
 
However it doesn't seem to work for my 6500.  I know the 6500 uses PFC for QOS but I have no idea how it works.  how I can guarantee a vlan 100mbps across a 1gig link?

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved