i would like to check out what's the difference between the naming convnetion for the 6500 IOS.
I read the data sheet to support my POC deployment to support NCS v.1 the 6500 IOS need to upgrade to 12.2 (33) SXI
Is it able to work if i using SXJ instead of SXI, with the same IOS version 12.2 (33)?
how can we upgrade 6500 non modular ios to normal 6500 ios?
View 5 Replies View RelatedIs there functionality difference in Supervisor Engine 2 and Supervisor Engine 2T for Catalyst 6500 ?
View 3 Replies View Relatedexplain me the difference between FTE-10G and SFP-10G-SR, being focus on an architecture Nexus.
View 5 Replies View RelatedI found a 851 router and tried to build a ezvpn tunnel. The issue I am running into now is that a 851 router can only have one vlan in its database. I need two vlans to go into the EZvpn tunnel with using another device. So can you tell me if a 881 router can have more than one vlan created on the router and can those vlans be assigned to a interface and can I create a svi for each of those vlans as well.
View 2 Replies View Relatedwhat the difference betwen these two cards? SFP-10G-SR or SFP-10G-LR
View 2 Replies View Relatedwhat the difference between L2 Vs L3 VLAN? in know in which situation i use L2 Vlans but i don't know that about L3 Vlan.
View 2 Replies View RelatedI've acquired an 871W, because I'd like to use wireless, to replace my 851. I Ft Pd the 851's configuration to my FTP server and then Ft Pd this to the 871W. Save for the fact that this has a radio interface (currently shutdown), everything works save for FTP from the outside. I can not even telnet to port 21 of any of the internal FT servers. I can telnet to any other port (ssg, smtp, HTTP, https, etc.) but FTP will not pass. What's the difference?
View 12 Replies View RelatedWhat is the difference between Operating temperatue & storage temperature of switch C3560E ?
View 2 Replies View RelatedWhat is the different between WS-X6148A-GE-TX and WS-X6148-GE-TX ? Currently, I can not use MTU command on X6148 but can on X6148A.This two cards installed in cat6509E.
View 2 Replies View Relatedterms of Performance for 3925, 3925E and 3945.
didn't see much different between 3925 and 3925E except an additional port.
what is difference between Cisco catalyst 3750e 48 and SF300-48p.
View 3 Replies View RelatedI have a cisco WS-C3750G-24TS with IOS flash :/ c3750-mz.122-ipservicesk9-25.SEB4.bin "
I purchased a new Cisco WS-C3750X-24 with the IOS flash :/ c3750e-universalk9-mz.150-1.SE/c3750e-universalk9-mz.150-1.SE.bin. ( NEW )
When i configured a stack between the two 3750, the new switch restarted due the version mismatch (different IOS´s);
We have two versions:
WS-C3750G-24TS-ipservicesk9 flash :/ c3750-mz.122-25.SEB4.bin "
VS
WS-C3750X-24 flash :/ c3750e-universalk9-mz.150-1.SE/c3750e-universalk9-mz.150-1.SE.bin.
Is that possible to configure a stack between then?
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Tenho um cisco WS-C3750G-24TS com o IOS flash:/c3750-ipservicesk9-mz.1
22-25.SEB4.bin"
Adquiri um novo cisco WS-C3750X-24 com o IOS flash:/c3750e-universalk9-mz.150-1.SE/c3750e-universalk9-mz.150-1.SE.bin.
[code]...
What is the difference between IP Base and Universal for 3750X switches?
View 2 Replies View RelatedI will go to buy a core 4506 but I'm comfusing about the Sup engines and the Fiber module. What is the different between the Sup7 and Sup7L?in the fiber module that I will go to buy is it contain the SFP inside or I have to buy the SFP ( WS-X4612-SFP-E ). also what is the different between the SFP and GBIC?
View 4 Replies View RelatedSwitch A is: WS-C2960-48TC-S
Switch B is: SG 300-10MP
Neither switch supports a similiar transceiver module. We are looking at transceiver GLC-SX-MM for Switch A, and MGBSX1 for Switch B all the Layer-1 information (SX / wavelength, Multi Mode, etc.) I am able to find out about the two transceivers seems to match, so would there be any issue by having these 2 "different" transceivers at either end?
I want to choose a pair of switches for our data center.What I need: 48 x 1GE access ports, 2 x 10GE uplink ports.Nice feature of 3750-X is stacking. So what features has 4948-10GE? Why I should prefer that switch?
View 11 Replies View RelatedAre there any differences between the autoqos commands on a WS-C2960S switches (or in any other series)? Follow the commands:
- auto qos trust
- auto qos voip trust
I was checking the documentation on this link:
URL
And couldn't find any great difference between the two commands, as far as I could see they'll set the Ingress and Egress queues the same way.
Are there any differences between those two commands (auto qos trust and auto qos voip trust)? If so, when should I use one and the other?
What is the difference between sdm prefer access & sdm prefer default & sdm prefer lanbase-routing? When do we use these options?
View 2 Replies View RelatedAs per my understanding 6509 all slots are dual channel, so 9 slot * 40 per slot (20 g in and 20 g out) = 360 GB How cisco claim the 720 ?? What about the 6513 chassic switch fabric connection?
View 5 Replies View RelatedI am seeing a strange situation on my 6500 switch?By having snmp walk on '1.3.6.1.4.1.9.9.109.1.1.1.1.3' (== cpmCPUTotal5sec), I came to know that there are two processor and the cpu util for switching processor is gone to 88 % and some time creeps to 99 %.
snmpwalk -v2c -c "removes" sw6500 '1.3.6.1.4.1.9.9.109.1.1.1.1.3'
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.1 = Gauge32: 12 (--- this is for CPU of Router Processor )
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.3 = Gauge32: 99 (--- this is for CPU of Switching Processor )
but when I do sh process cpu on the console, all looks normal as it shows cpu utilization of RP. why the value is so high on the switching processor ?
In my 6513 switch chassis we have two Supervisor Engines 720 one is marked Active other as Hot. what is the diffrence in their mode as by name I suppose that Active one is currently in use and Hot one is in standby mode.They are showing in this manner.
Module Ports Card Type
7 2 Supervisor Engine 720 (Active)
8 2 Supervisor Engine 720 (Hot)
what is the difference between Cisco Nexus switches and the usual catalyst 3750 switches.I do understand the operating system in both these are different.
When will we suggest using Cisco nexus instead of usual Cisco switches? Also what interface does Cisco nexus like 5548 come with , is it both copper and fiber?
Cisco let us try a CISCO C3750X- 24T-S Stack (2 switches) ->> IpBase Sofware licence We've 2 Hyper-v 2008 R2 and one SAN Netapp FAS2040 connected via Iscsi.All was working well with this stacks.Hyper-V see Nas Iscsi interface without problem. Even with basic stack config (no Vlan, ect...).Then, after this test period, we bought a C3750X-24T-L stack (2 switches) to replace the stack lent by Cisco.This one is LanBase Software.
With this stack, hyper-v work very bad ! We've got a lot of Iscsi error in the eventvwr.I can't access luns.So, is there a difference between LanBase and IpBase for a iscsi use ?I put the 24T-S config on the 24T-L switch without pb. So config is the same on both stacks...Also i've got a "TestPortAsicLoopback" = "Failed" on the new stack...I've tried with other stack cables. Not better.
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?
View 1 Replies View RelatedI'm looking to restrict Inter-VLAN routing through L3 switch (cisco 6500) and wanted to know best possible way to do it. I used VACL and achieved success to some extent, but my config is making clients take up to 5-6 mins to authenticate IP address from the DNS (bootps).My VACL config was as follows:
Subnet to restrict is 10.100.15.0 (VLAN 15)
STEP 1: Created extended ACL to allow bootpc/bootps through DNS
ip access-list extended EACL_DNS
permit udp any eq bootps any
permit udp any eq bootpc any
STEP 2: Created standard ACLs to allow only relevant subnet, server VLANs & some IPs from other subnets for printers/scanners etc.
ip access-list standard SACL_VLAN_15
permit 10.100.15.0 0.0.0.255 (the subnet I'm restricting)
permit 10.100.50.0 0.0.0.255 (server VLANs)
permit 10.100.25.45 0.0.0.0 (printer in another VLAN which has to have access in VLAN 15)
STEP 3: Created VLAN access list
vlan access-map VACL_15 10
match ip address EACL_DNS
action forward
vlan access-map VACL_15 20
match ip address SACL_15
action forward
STEP 4: Applying VLAN Access list on VLAN 15 vlan filter VACL_15 vlan-list 15 Though the above works, below is noted:
1. I'm still able to PING 10.100.15.2 (the switch virtual interface) from outside the subnet, which I don't intend to do so. Howeve all cients in the subnet have no connectivity from outside the VLAN 15.
2. As mentioned its taking quiet some time to negotiate with the DNS server at system boot time.
I used to "ip routing" command in order to enable inter-vlan routing, for example with 3750 cisco. I have a 6503 cisco with SUP720 MSFC3. I was able to create some vlans but I can not configure inter-vlan routing.
sw#conf t
Enter configuration commands, one per line. End with CNTL/Z.
swsur(config)#ip routing
[Code]....
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?hes, do we need to enable the "ip routing" command manually for intervlan routing?
View 2 Replies View RelatedWhat the different between using hsrp on vlan interface and on physical port (routed port) on Cisco 3750 Switch? Wha the benefits?
View 3 Replies View RelatedWhere is the "ip routing" command in Cisco switch 6500 series?
is the ip routing enable by default accoridng to the: [URL]
I have tried to test copy tftp: numerous time with no success. I believe the reason it is failing is my laptop to Ethernet port is in vlan 62 and the tftp process operates in a different IP space.I am using gig 7/1 and configuring my laptop nic for x.x.x.254 mask 255.255.255.0. I can ping from laptop to gateway) and I can ping from the switch to my laptop using ping vrf production x.x.x.254. Can you tell me what vlan I need to set my laptop connection in or if there is something else I need to change to make tftp work on vlan62?Does TFTP only work in vlan1 or can it be changed?
View 2 Replies View Relatedhow to upgrade IOS in switch 6500 connect in VSS from 12.2(33)SXI IOS to 12.2(33)SXJ?
View 3 Replies View RelatedWe are setup like a hotel style workers camp. We have wings full of rooms and residents with 3750 stacks in them. Those switches connect back to our core 6500's. The network is mostly all Layer 3, interfaces are routed with IPs.
When it was built before my time they included an ACL for each wing so that residents couldn't access internal devices (IE SSH to 6500) but I've come to notice it's not working.
I see hits on the ACL for accepts but nothing is hitting the deny rule at the top.Here is the configuration below:
mls qos aggregate-policer INTERNET1 24000000 80000 80000 conform-action transmit exceed-action drop
mls qos aggregate-policer INTERNET2 24000000 80000 80000 conform-action transmit exceed-action drop
mls qos aggregate-policer INTERNET 24000000 80000 80000 conform-action transmit exceed-action drop
[Code] ....