Cisco Switching/Routing :: C3750X Stack / Difference Between LanBase And IPBase For ISCSI?
Dec 26, 2011
Cisco let us try a CISCO C3750X- 24T-S Stack (2 switches) ->> IpBase Sofware licence We've 2 Hyper-v 2008 R2 and one SAN Netapp FAS2040 connected via Iscsi.All was working well with this stacks.Hyper-V see Nas Iscsi interface without problem. Even with basic stack config (no Vlan, ect...).Then, after this test period, we bought a C3750X-24T-L stack (2 switches) to replace the stack lent by Cisco.This one is LanBase Software.
With this stack, hyper-v work very bad ! We've got a lot of Iscsi error in the eventvwr.I can't access luns.So, is there a difference between LanBase and IpBase for a iscsi use ?I put the 24T-S config on the 24T-L switch without pb. So config is the same on both stacks...Also i've got a "TestPortAsicLoopback" = "Failed" on the new stack...I've tried with other stack cables. Not better.
View 4 Replies
ADVERTISEMENT
May 16, 2013
Recently one of our stack switch got failed, Rma raised but we received some different part number.The dobut is like can we stack the below switches.
ws-c3750x-48p-l v02 (old switch)
ws-c3750x-48pf-s v04 (RMA switch)
View 2 Replies
View Related
Jan 8, 2012
Can we use WS-C3750X-12S-S and WS-C3750X-24T-S in a single stack?
View 7 Replies
View Related
Mar 27, 2013
Which is the best and advanced IOS for c3750x-48P-E stack switch among below listed IOS.
c3750e-universalk9-mz.122-58.SE2 ?
or
c3750e-universalk9-mz.122-55.SE6..??
View 4 Replies
View Related
Dec 18, 2011
Can a WS-C3750X-12S coexist in an existing stack made up of a WS-C3750G-12S and a WS-C3750G-24TS?
View 7 Replies
View Related
Feb 3, 2012
can i stack cisco (ws-c3750G-12s) with (ws-c3750X-24p-poe-s) with (ws-c3750-48p-10/100 poe) i mean even a switch is 10/100 and the other switch is 10/100/1000?
View 3 Replies
View Related
Oct 26, 2011
Any issues are reported while configuring power stack ? We did several times with 12.2.58SE1 and SE2, sometimes the power stack is created automatically, sometimes needs to be configured manually. Looks like the behavior is not the same. Maybe it depends on the number/type of switches and number/type of power supplies.
View 1 Replies
View Related
Oct 26, 2011
Does the color strips on C3750X stack power cables mean anything, I mean the green and yellow ones. On all Cisco pictures the green one seems to be plugged in the upper ports. I asked local Cisco representative, but he seems not to be sure. We tried to try different scenarios, and it looks like it does not matter what cable end we use. We do not have any external power supply, only interconnecting C3750Xs.
View 1 Replies
View Related
Dec 6, 2012
I am having an issue with adding a c3750x switch to an existing switch stack Currently there is 2 x WS-C3750X-48P and I am trying to add another WS-C3750X-48P to this switch I have cabled the switch to the stack using the stack cables and added the command to provision the switch on the exisitng stack. However when I turn the switch on it just goes on its own stack.
I noticed the new switch had a later version of IOS so have downgraded this to the same version as the other switches but still no joy Here is the sh ver from the exisitng stack
uptime is 4 weeks, 4 days, 23 hours, 30 minutes
System image file is "flash:/c3750e-universalk9-mz.122-53.SE2/c3750e-universalk9-mz.122-53.SE2.bin"
License Level: ipbaseLicense Type: PermanentNext reload license Level: ipbase
cisco WS-C3750X-48P (PowerPC405) processor (revision A0) with 262144K bytes of memory.Processor board ID FDO1448Z0FJLast reset from power-on21 Virtual Ethernet interfaces1 FastEthernet interface156 Gigabit Ethernet interfaces6 Ten Gigabit Ethernet interfacesThe password-recovery mechanism is enabled.
[code]....
View 3 Replies
View Related
Aug 9, 2012
We have WS-C3750-24FS switches stacked supporting users on our LAN. I want take advantage of the netflow capabilities of the WS-C3750X using the C3KX-SM-10G card.
Would I be to see netflow data coming from the WS-C3750's if I stacked it with the WS-C3750X?
Also I read that the C3KX-SM-10G card would support a 1G SFP is that correct?
View 1 Replies
View Related
Mar 15, 2013
I have two WS-C3750X-48T-S which is "IP BASE" licensed, which are connected as stack.I need to use Policy Based Routing (PBR) to direct Vlans to two different gateways, and command "ip policy route-map" which is supported only in C3750-IPSERVICES license.Do I need upgrade only master switch with Cisco IOS IP Services - product upgrade licenseMfg. Part#: L-C3750X-48-S-E, or both switches need to be upgraded?
View 20 Replies
View Related
Jun 11, 2013
I'm trying to stack 3750G & 3750X. As discussed in previous threads I am aware of that the version need to match.
Here the switch details:
Switch Ports Model SW Version SW Image
------ ----- -------------- ----------
* 1 24 WS-C3750G-24T 12.2(55)SE7 C3750-IPBASEK9-M
---------------------------------------------------------------------------------------------------------------
* 1 54 WS-C3750X-48 12.2(55)SE7 C3750E-IPBASEK9-M
I have changed the universal IOS on the 3750X to IP base..but they still wont come up as a stack. On the 3750X I don't see any log entry, on 3750G (major version mismatch).
View 4 Replies
View Related
Feb 12, 2012
I have a couple of WS-C3750X-48T-L and a couple of WS-C3750X-12S-S, I want to stack all four of them together into a single stack. WS- C3750X-12S-S are running c3750e-universalk9-mz.122-58.SE2 whereas WS-C3750X-48T-L are running c3750e-universalk9-mz.122-55.SE3.I have got a couple of queries as under:What are the options to achieve putting all these 4 switches into a single stack? Can the LAN Base switches upgraded to IP Base?
View 3 Replies
View Related
Jul 15, 2012
I have a cisco WS-C3750G-24TS with IOS flash :/ c3750-mz.122-ipservicesk9-25.SEB4.bin "
I purchased a new Cisco WS-C3750X-24 with the IOS flash :/ c3750e-universalk9-mz.150-1.SE/c3750e-universalk9-mz.150-1.SE.bin. ( NEW )
When i configured a stack between the two 3750, the new switch restarted due the version mismatch (different IOS´s);
We have two versions:
WS-C3750G-24TS-ipservicesk9 flash :/ c3750-mz.122-25.SEB4.bin "
VS
WS-C3750X-24 flash :/ c3750e-universalk9-mz.150-1.SE/c3750e-universalk9-mz.150-1.SE.bin.
Is that possible to configure a stack between then?
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Tenho um cisco WS-C3750G-24TS com o IOS flash:/c3750-ipservicesk9-mz.1
22-25.SEB4.bin"
Adquiri um novo cisco WS-C3750X-24 com o IOS flash:/c3750e-universalk9-mz.150-1.SE/c3750e-universalk9-mz.150-1.SE.bin.
[code]...
View 4 Replies
View Related
Nov 7, 2012
Can i put in stack the ws-c3750X-12S-E and ws-c3750X-48P-E? considering the follow features:
WS-C3750X-48P-E (Catalyst 3750X 48 Port PoE IP Services)
S375XVK9T-12253S
CAT 3750X IOS UNIVERSAL WITH WEB BASE DEV MGR
WS-C3750X-12S-E (Catalyst 3750X 12 Port GE SFP IP Services)
C3KX-NM-10G
S375XVK9T-12255SE
CAT 3750X IOS UNIVERSAL WITH WEB BASE DEV MGR
View 2 Replies
View Related
Feb 3, 2013
one of our switches (WS-C2960G-24TC-L). When I try to turn on the lanbase-routing feature using sdm prefer lanbase-routing, it gives me an error (Unknown command). I tried "sdm prefer ?", and lanbase-routing wasn't there (only qos, default and dual IPv4 & IPv6). The switch is running on image C2960-LANBASEK9-M version 12.2(50)SE5.We have another switch (WS-C2960S-24TS-L), running on image C2960S-UNIVERSALK9-M version 12.2(55)SE5, and I can enable lanbase-routing feature. If I upgrade the WS-C2960G-24TC-L to version 12.2(55)SE5, will it be able to do inter-vlan routing? Or is the switch itself totally limited to VLAN configuration only?
View 4 Replies
View Related
Jan 21, 2010
I have the following issue; I am getting a duplex mismatch between a Cisco 2960 TT-L Switch running IOS 12.2(35) LAN Base Image (Gig0/1) and a Cisco 6506 Switch running IOS 12.2(33)SXH Adv IP Services (Gig2/19).
I have tried several combinations of the duplex/speed settings on both sides but the only that works is setting duplex/speed AUTO on the Cisco 2960 which ends up autonegotiating to HALF duplex and 100Mbps.
View 9 Replies
View Related
Oct 27, 2011
what is difference btw c2960-lanbasek9-mz.122-44.SE1.bin with c2960-lanbase-mz.122-44.SE1.bin.I found that these two IOS are available in below link and both two are released in same time... [URL]
View 2 Replies
View Related
Mar 19, 2012
I haven't worked with infrastructure much lately but planning on replacing a Dell switch used for a small iSCSI SAN with a Cisco 3560x. Switch is sstorage ONLY, network handled through different switches. I believe I want to disable spanning tree and configure trunking for the 4 GB ports connected to the storage array. The switch is providing connectivity to SAN via multiple GB connections and then also multiple GB connections to 3 Vmware hosts.Can you look over the changes I made to config below and let me know if I am on the right track.
I also plan to add a second switch later with the 10GB modules to interconnect for redundancy (but not worried about that part for now). I do not plan on using jumbo frames.
Here are my questions
1) Is the best way to globally disable spanning tree for the switch?
2) Did I trunk the ports correctly below?
3) Should I apply any specific SmartRoles to the 4 SAN NICs (GE1-4) or to host NICs (GE13-20)?
4) Anything additional I should do to handle iSCSI data?
Here is a copy of the config so far with my changes marked in RED.
storage1#wr tBuilding configuration...
Current configuration : 1696 bytes!version 12.2no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-
[Code].....
View 2 Replies
View Related
Jan 14, 2013
Upgrading two 6509-E routers containing sup32's to two new 6509-E routers containing sup2T's. We run a large OSPF network but our core mainly is a switched network and only has about 5 Vlans. Now this could change in the future and there maybe more Vlans on it.
Just after realising our new sup32's shiped with ipbase instead of ipservices. Version is s2t54-IPBASEK9_NPE-M. My question is is this version ok for routing?
Our old current 6509's are version s32p3-ipbasek9-mz.122-18.ZYA3.bin and they do some routing about the same amount these new routers will do. Here is a summary of the routing table:
IP routing table name is Default-IP-Routing-Table(0)
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 3 424 640
static 0 0 0 0
ospf 1 26 348 27520 59840
Intra-area: 366 Inter-area: 0 External-1: 0 External-2: 8
NSSA External-1: 0 NSSA External-2: 0
internal 12 14160
Total 39 351 27944 74640
Removing Queue Size 0
Will I need to upgrade the new sup2T's to ipservices or will this version work ok?
View 16 Replies
View Related
Mar 11, 2012
I've been searching the forums to see if any other users have completed this type of configuration successfully with not much luck. I have a Cat 6509 currently in production. We have several Vlans and all communication and routing is funtional in our environment. We are going to be adding an iSCSI Storage environment, and within a couple of months, adding a 3 Host VMware farm. I've configured several iSCSI environments using dedicated switches for the iSCSI network but never to existing production switches.My thoughts are to add two iSCSI Vlans outside of the production IP Scheme to the 6509 with no SVI, attach storage controller's NICS ports to the management network and of course, other available NIC ports to the iSCSI network. My question is, what is the best practice in configuring the 6509 i.e. switchports, Jumbo Frames, Flow-Control to support iSCSI on a 6509 that is in production and what are possible risks if any with enabling Jumbo Frames, Flow-Control etc?
View 2 Replies
View Related
Feb 10, 2013
My current version IOS is cat4500e-ipbase-mz.122-53.SG5.bin. I just got a new version cat4500e-entservicesk9-mz.122-53.SG5.bin.I put the new version in bootflash: directory and tried various methods of starting the IOS up to run the new version but it always started in the original ipbase version. My start-config shows:
boot-start-marker
boot system flash bootflash:cat4500e-entservices9l-mz.122-53.SG5.bin
boot-end-marker
and I even deleted the ipbase version in the bootflash: directoy so then my switch would not even boot up at all and hung in rommon. In rommon I tried
boot bootflash:cat4500e-entservicesk9-mz.122-53.SG5.bin
and the result I got back was
File has bad file magic number: 0x0
So I had to point the switch to my tftp server and boot back into a back up copy of ipbase. how I can get my new IOS version to work? I understand I might have to download it again but I just got it so I am skeptical it is a bad file. [URL] as a procedure guide and I do notice some of those commands/steps do not work on my 4900m switch.
View 3 Replies
View Related
Jul 23, 2012
I imagine this question has been posted a million times before but here goes. I am trying to image a number of machines via Ghost Cast server across a 3750X stack running multiple V LAN's. I am running the IP BASE image so am aware that multicast functionality is limited.
I am running 12.2(55)SE3. I have tried adding both V LAN's into an IGMP group using the "ip igmp join-group" command which shows both V LANs as part of the group but to no real effect. To be honest though I am clutching at straws! I'm just starting to read through the documentation so hopefully that will work.
View 3 Replies
View Related
May 18, 2013
After deleting configuration with „write erase“ and reloading, our Cisco Catalyst 4503 with version cat4500e-universal.SPA.03.02.00.XO.150-2.XO.bin, and licence ipbase, doesn't recognize any command regarding SSH. We tried configuring SSH key with „crypto key generate“, but that command is not recognized either.
View 1 Replies
View Related
Aug 7, 2011
Is it possible to have a WS-C3750G-12S-S and a WS-C3750X-24T-L in the same stack, if so do they need to both be running the same software version/IOS.
View 6 Replies
View Related
May 28, 2012
we have just purchased a few 3750x's that we intend to add to our 3750g stacks. We've purchased the 10gb uplink modules, C3kx-nm-10gt, but when they are installed they are not appearing in the switches web gui nor can you configure them correctly. If we upgrade a 3750x to 15.0.1 they seem to work fine. All of our current 3750g's are running 12.2(58)SE2 IPBASE so we don't really want to have to upgrade them all to 15.0.1
Are we missing something or do the 10gb modules only work properly with ios 15.0.1?
View 3 Replies
View Related
Jan 10, 2012
Symptoms: The switch hangs - after a hard reboot and after two hours switch No. 2 flew out from the stack. After the reboot, everything returned to normal and now when a few days passed switch works without problems. Devices: WS-C3750X-24T-S
View 3 Replies
View Related
Sep 6, 2011
I have running a Stack with two C3750G-24TS-S1U with the IOS c3750-ipbasek9-mz.122-50.SE3.Now I want put a new C3750X-24T-S in the existing stack. I have read this is possible. I have running a other mixed stack with a C3750G-12S and an C3750E-48TD. Its running fine until I want to make an IOS update. The update was done with the CW LMS 3.1. After the automatic update and restart only the C3750E had an new IOS the C3750G doesn't have any IOS. Do I have the same problem with the mixed Stack C3750G and C3750X?Do I have to upgrade the IOS by copying the different IOS Versions ( c3750-ipbasek9-mz.122-50.SE3 / c3750e-ipbasek9-mz.122-50.SE3) to every switch ?
View 5 Replies
View Related
Aug 19, 2011
I downloaded all updates packages of the device for the Cisco View and I could not the show the image
View 1 Replies
View Related
Feb 27, 2013
Is there a stacking cable that is "bent"?Im using this cable:"CAB-STACK-50CM", "Cisco StackWise 50CM Stacking Cable".But it takes up to much room in the back of the switch, is there such a thing as "bent" stacking cable.
View 1 Replies
View Related
Oct 31, 2012
I have 3 switches in my 3750 X stack. I am getting the following error in the logs: %PLATFORM_STACKPOWER-4-PRIO_CONFLICT: Switch 1's power stack has conflicting power priorities. Not sure what I should do next. Below is my Stack-power configuration:
Power stack name: Powerstack-1 Stack mode: Power sharing Stack topology: Ring Switch 1: Power budget: 735 Low port priority value: 20 High port priority value: 10 Switch priority value: 2 Port 1 status: Connected Port 2 status: Connected Neighbor on port 1: c464.1308.7900 Neighbor on port 2: e8b7.4827.e680
Switch 3: Power budget: 729 Low port priority value: 22 High port priority value: 13 Switch priority value: 4 Port 1 status: Connected Port 2 status: Connected Neighbor on port 1: 2894.0fd9.9f00 Neighbor on port 2: 2894.0fd8.e200
Switch 2: Power budget: 690 Low port priority value: 21 High port priority value: 12 Switch priority value: 3 Port 1 status: Connected Port 2 status: Connected Neighbor on port 1: 2894.0fd8.e200 Neighbor on port 2: c464.1308.7900
Each switch has its own 715W power supply in it and all check out OK.
View 3 Replies
View Related
Sep 24, 2012
A site that i am responsible for has the following equipment installed:
2 x 3750G Switches configured as a stack using Stackwise - Collapsed Core/Distribution Layer
5 x 2960G Switches as Access Layer switches
WAN connections into the Core/Distribution Layer are all Gigabit Ethernet over Fibre.This is a dedicated CCTV Network with 50 Cameras all streaming video into the Core (decoders connected to access switches)Each 2960G has 2 links to the Core/Distribution 3750G Switches, 1 to each switch - Gigabit.I'm running rapid-pvst on all switches, so spanning tree is blocking one of the ports and effectively halving the 2 gig bandwidth. Next year our customer is going to add in a further 50 - 60 cameras.After monitoring the current loading on the ports in use, we have suggested to the customer that the 2 connections to each should be Ether-channeled together. [code]
First interface takes commands no problem, keep getting the message that etherchannel cannot be configured across different switches in a stack when i try to put the second interface commands on.
View 8 Replies
View Related
Aug 6, 2012
It is said that the switching fabric of WS-C3750X-24T-E is 160Gbps.Could any body tell me what is switching fabric, any relevance or difference from forwarding rate?,Is there any document to know how will the switch reach the 160Gbps full switching fabric performance?
View 5 Replies
View Related
