Cisco Switching/Routing :: Upgrading 4900m IOS From IPBase To Enterprise?
Feb 10, 2013
My current version IOS is cat4500e-ipbase-mz.122-53.SG5.bin. I just got a new version cat4500e-entservicesk9-mz.122-53.SG5.bin.I put the new version in bootflash: directory and tried various methods of starting the IOS up to run the new version but it always started in the original ipbase version. My start-config shows:
boot-start-marker
boot system flash bootflash:cat4500e-entservices9l-mz.122-53.SG5.bin
boot-end-marker
and I even deleted the ipbase version in the bootflash: directoy so then my switch would not even boot up at all and hung in rommon. In rommon I tried
boot bootflash:cat4500e-entservicesk9-mz.122-53.SG5.bin
and the result I got back was
File has bad file magic number: 0x0
So I had to point the switch to my tftp server and boot back into a back up copy of ipbase. how I can get my new IOS version to work? I understand I might have to download it again but I just got it so I am skeptical it is a bad file. [URL] as a procedure guide and I do notice some of those commands/steps do not work on my 4900m switch.
View 3 Replies
ADVERTISEMENT
Jan 14, 2013
Upgrading two 6509-E routers containing sup32's to two new 6509-E routers containing sup2T's. We run a large OSPF network but our core mainly is a switched network and only has about 5 Vlans. Now this could change in the future and there maybe more Vlans on it.
Just after realising our new sup32's shiped with ipbase instead of ipservices. Version is s2t54-IPBASEK9_NPE-M. My question is is this version ok for routing?
Our old current 6509's are version s32p3-ipbasek9-mz.122-18.ZYA3.bin and they do some routing about the same amount these new routers will do. Here is a summary of the routing table:
IP routing table name is Default-IP-Routing-Table(0)
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 3 424 640
static 0 0 0 0
ospf 1 26 348 27520 59840
Intra-area: 366 Inter-area: 0 External-1: 0 External-2: 8
NSSA External-1: 0 NSSA External-2: 0
internal 12 14160
Total 39 351 27944 74640
Removing Queue Size 0
Will I need to upgrade the new sup2T's to ipservices or will this version work ok?
View 16 Replies
View Related
Jul 23, 2012
I imagine this question has been posted a million times before but here goes. I am trying to image a number of machines via Ghost Cast server across a 3750X stack running multiple V LAN's. I am running the IP BASE image so am aware that multicast functionality is limited.
I am running 12.2(55)SE3. I have tried adding both V LAN's into an IGMP group using the "ip igmp join-group" command which shows both V LANs as part of the group but to no real effect. To be honest though I am clutching at straws! I'm just starting to read through the documentation so hopefully that will work.
View 3 Replies
View Related
May 18, 2013
After deleting configuration with „write erase“ and reloading, our Cisco Catalyst 4503 with version cat4500e-universal.SPA.03.02.00.XO.150-2.XO.bin, and licence ipbase, doesn't recognize any command regarding SSH. We tried configuring SSH key with „crypto key generate“, but that command is not recognized either.
View 1 Replies
View Related
May 28, 2012
we have just purchased a few 3750x's that we intend to add to our 3750g stacks. We've purchased the 10gb uplink modules, C3kx-nm-10gt, but when they are installed they are not appearing in the switches web gui nor can you configure them correctly. If we upgrade a 3750x to 15.0.1 they seem to work fine. All of our current 3750g's are running 12.2(58)SE2 IPBASE so we don't really want to have to upgrade them all to 15.0.1
Are we missing something or do the 10gb modules only work properly with ios 15.0.1?
View 3 Replies
View Related
Dec 26, 2011
Cisco let us try a CISCO C3750X- 24T-S Stack (2 switches) ->> IpBase Sofware licence We've 2 Hyper-v 2008 R2 and one SAN Netapp FAS2040 connected via Iscsi.All was working well with this stacks.Hyper-V see Nas Iscsi interface without problem. Even with basic stack config (no Vlan, ect...).Then, after this test period, we bought a C3750X-24T-L stack (2 switches) to replace the stack lent by Cisco.This one is LanBase Software.
With this stack, hyper-v work very bad ! We've got a lot of Iscsi error in the eventvwr.I can't access luns.So, is there a difference between LanBase and IpBase for a iscsi use ?I put the 24T-S config on the 24T-L switch without pb. So config is the same on both stacks...Also i've got a "TestPortAsicLoopback" = "Failed" on the new stack...I've tried with other stack cables. Not better.
View 4 Replies
View Related
Mar 10, 2013
I am just going to deploy some new 4900Ms for a customer. Want to know if configuring management for 4900 (everything like NTP, AAA, SNMP , DNS ) is doable through management interface in management VRF and there are no caveats to be aware of.
View 1 Replies
View Related
Mar 11, 2013
I would like if is possible to stack a Cisco 4900M with a 2960S. I know it is not the most common situation but i need it.
View 1 Replies
View Related
Apr 4, 2013
I have an issue with couple of Cisco 4900M switches. We just got them and tried to use the TwinGig Converter on the 4 ports 10G module.
The problem is that the switches sees the new module in slot 2 and when we are inserting the TwinGig Converters we are getting the error message and when we are trying to type the command this command it does not work."hw-module module <slot> port-group <group> select gigabitethernet",When we go to config T, the only thing we can type is "hw-module module <slot> and if we do a ? the only thing is available is logging and power and we can't type
Port-Group or anything else. Is this a hidden command or we have to something else?
View 1 Replies
View Related
Jul 30, 2012
on a Cisco 4900M running IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-ENTSERVICESK9-M), Version 15.0(2)SG1, RELEASE SOFTWARE (fc4) I'm getting a lot of packets on CPU Q "L3 Glean, 6".What is that queue and what could be the root cause?
Packets Received by Packet Queue
Queue Total 5 sec avg 1 min avg 5 min avg 1 hour avg
---------------------- --------------- --------- --------- --------- ----------
Host Learning 1563 0 0 0 0
L2 Control 1138188 3 0 0 0
Ttl Expired 2 0 0 0 0
L3 Glean, 6 4889394 4067 4381 3367 779
[code]....
View 1 Replies
View Related
Aug 10, 2012
Is it possible to use 1GB (SFP / Copper) on the built-in 8 x X2-10GB ports without any Network Module of 1/10GB. If so how.
View 2 Replies
View Related
Jan 4, 2012
I have a client whom has a 4900M switch as their SAN switch. They are getting ready to upgrade their SAN to use 10G.I had quoted them a price for an X2 module, but I am unclear based on pictures I have seen of the part number
X2-10GB-SR
whether or not the X2 module plugs into the X2 slot on the switch, AND then also has to have a transceiver put in it to receive the SC ends of the Fiber jumper, or whether the SC ends of the fiber jumper plug into the X2 module directly.
View 5 Replies
View Related
Mar 11, 2013
I would like to know if i can and how stack a Cisco 4900M with a 2960S. I know it's not the most common but i need it.
View 2 Replies
View Related
May 7, 2012
I have this 4900M running version 12.2(54)SG1. I the log I get this 3 lines:
May 8 08:32:15: %C4K_SWITCHINGENGINEMAN-4-TCAMINTERRUPT: (Suppressed 429 times)flCam0 aPErr interrupt. errAddr: 0xC48 dPErr: 1 mPErr: 0 valid: 1
May 8 08:32:24: %C4K_L3HWFORWARDING-4-FLTCAMPARITYERROR: (Suppressed 866 times)FL Tcam Perr with no FwdEntry Hw index: 3144 Hw entry: Sw entry:
May 8 08:32:45: %C4K_SWITCHINGENGINEMAN-4-TCAMINTERRUPT: (Suppressed 432 times)flCam0 aPErr interrupt. errAddr: 0xC48 dPErr: 1 mPErr: 0 valid: 1
They seems to be coming on regular basis, repeating every minute. I've tried Google and the most relevant info I can find is this {URL}. But it says "Upgrade software to IOS version 12.2(52)SG or later OR 12.2(50)SG4 or later. ". I'm already running 12.2(54), so why does this 3 line repeatedly show up in the log every minute.
View 2 Replies
View Related
Jan 1, 2013
First time user of cisco hardware and we just purchased the 4900m catalyst switch. My question is very general. I am simply hoping to network 3 servers together and I do not wish to do any fancy or advanced configuration. Can I simply use the web management interface for network administration and setup? I just downloaded the Catalyst 4500 Series Switch Cisco IOS software configuration guide and they talk about Cisco View network management system, is this my answer or is this what most people use for basic configuration and administration?
View 3 Replies
View Related
Feb 12, 2013
I currently have IOS image cat4500e-entservices-mz.122-53.SG5.bin. According to my research it appears SPAN is supported on this OS. However, after looking at procedure notes using websites like here:
[url]... I cannot find and obviously not figure out how to use the SPAN command. My main objective is to simply setup a port mirror on one of my TenGigabitEthnet interfaces and from what I read SPAN is the best way to setup a tap interface on a cisco switch.
View 2 Replies
View Related
Dec 8, 2011
I am just going to deploy some new 4900Ms for a customer. Want to know if configuring management for 4900 (everything like NTP, AAA, SNMP , DNS ) is doable through management interface in management VRF and there are no caveats to be aware of.
View 1 Replies
View Related
Dec 18, 2012
We have to cisco WS-C4900M with Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-IPBASE-M), Version 12.2(53)SG5, RELEASE SOFTWARE (fc1).We have four gigabit link connected between those two switches.We have create a LACP port channel with those four ports on both switches. Ether-channel is up and running and defined with a load-balancing method of src-dst-ip.But when we test the load-balancing, it's not using the src-dst-ip rule with the XOR: [code]
View 5 Replies
View Related
May 12, 2012
I have 4900M with X2-10G-LX4I need to have a link from it to 3560X GLC-SX-MM using MM Fiber Patch Cord.any configuration required in 4900M to change the speed of X2-10GB-LX4 to 1GB ?
View 2 Replies
View Related
Jan 6, 2013
I have been trying to get the http server enabled so I can access Cisco Network Assistant. I have my interfaces configured but for some reason the server in not running, port 80 is still closed. [code]
View 2 Replies
View Related
Apr 13, 2010
I' ve three 4900M switches equipped with the WS-X4920-GB-RJ45 module and the WS-X4908-10GE module. Now I'm started to setup these switches in our lab environment for the first time. They behave a little bit strange in comparison with the C3750 series which I used before and which I will replace by these powerful machines.
I tried to setup these switches to be managed through the management port. I configured IP address, default route in the management vrf, set the source-interface for tftp,ssh,ftp and tacacs to use the management port. Ping using the manangement port was successful. After finishing theses steps I configured the TACACS and AAA settings accordingly the informations I found on CCO. I tested the settings with "test aaa group authentication" command- without success. On my Cisco ACS no request was received and the switch told me he could't reach the tacacs server. Other switches in the same IP subnet are working without failure, so firewall or server should not be the problem.
View 5 Replies
View Related
May 3, 2012
I am little confused with all these SFP types.
Can I use GLC-LH-SM, GLC-LH-SMD and SFP-GE-L with Twingig converter module? When I used Cisco configuration tool, the only option is GLC-LH-SMD for 1000BASE-LX.
View 4 Replies
View Related
Jan 17, 2010
I was wondering if a interface numbering scheme is available for the 4900M. Configuration includes 1 x 8Port 10G and 1 x 20Port 1G modules. would like to understand How the slots are addressedInterface AddressingTwinGig interface addressing
View 10 Replies
View Related
Dec 10, 2012
know if Private Vlans are supported on the Cisco 4900m switch when set in VTP version 3 and VTP disabled?Most documents just specify VTY transparent mode without mentioning the version, trying not to assume since this is production.
View 1 Replies
View Related
Jan 2, 2012
What would happened if a force a cat4500-entservicesk9-mz.122-54.SG on a SUP-II-Plus+TS? Considering that:
- The same IP base file tha is used on a SUP-II-Plus+TS is used uma a SUP-V
- The file size os the ent services IOS is just a bit bigger the ip base IOS.
- Especially the EIGRP were supported on the SUP-II-Plus+TS pior the 12.2-25
We need full support to EIGRP(or OSPF) because of the H.A that are been implemented and need to test it...
View 5 Replies
View Related
May 23, 2012
Got a question for 4900m with TwinGigi Converter. I bought couple TwinGigi Convert thinking to use it on fix module ports (8 * 10G ports on 4900m ten1/1 to 1/8). I follow TwinGigi configuration guide [URL]however, I am getting Invalid commands on hw-module:
Switch(config)#hw-module module 1 ?
logging Logging
Switch(config)#hw-module module 2 ?
logging Logging
power Enable/disable power to module in specified slot
[code]...
here is show ver and show mod:
Switch#show ver
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-IPBASEK9-M), Vers
ion 15.0(2)SG2, RELEASE SOFTWARE (fc3)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 07-Dec-11 20:20 by prod_rel_team
[code]...
View 1 Replies
View Related
Feb 2, 2012
Would like to know if the Cisco Catalyst 4900M Switches are stackable?
View 2 Replies
View Related
Feb 1, 2012
I am working in an enterprise LAN environment. We have about 100 switches, mostly 3560 and 3750's. This is a typical Cisco network, yet it's flat. No routing on the access layers. The core switch does do the routing. We use an third party vendor network monitoring tool, and we use Secure CRT to remote into devices.
Here's the problem. There was a device we stumbled into that had not been put into our monitoring software. It has the same IOS as our other devices. All I can say is that it's the same version and type. Each device has a management v LAN. And each device has it's own management IP. An ACL exists to prevent unauthorized SSH access into the devices, yet allows the management v LAN scope to get in.
So, here's the problem...we can't SSH into our problem mystery device, let's call it Switch X. Switch X has an IP of 10.10.100.150. Now, I can be logged into it's up link device, let's call it switch B. Switch B has an IP of 10.10.100.130. The ACL allows all devices from 10.10.100.0/24 to SSH. Our PC's at our desk are also in the same management V LAN. SSH version 2 is on the configs, and the domain names are the same on these two devices.
So, let's be clear. From my desktop, I can connect to any device on my network EXCEPT switch X. When I try to connect using SSH, port 22...it just sits there until it times out. I can do the same thing to any other switch, and connect just fine. We are using TACACS+ and RADIUS as well, and they are up and running just fine. The configs on Switch X like I said are the same for switch B, except it's IP address of course. While logged into switch B, I can do a CDP neighbor and see switch X connected via trunk link. Both sides are running dot1q encapsulation, and both are in trunk mode. I can ping switch X from switch B. When I try to SSH from B to X..I get timeout with no connection.
So, I hiked over to the building where switch X is located. I consoled into the switch. I confirmed that the ACL is the same as the ACL for switch B. It is set up to allow the management v lan inbound on the VTY 0 - 15. Yes, it's access-class (name) in on both vty 0 4 and 5 15. It also is set up for transport ssh in and transport ssh out.
I rechecked the domain name on Switch X; it was correct. I also did a crypto key and regenerated the crypto key. SSH v2 came up. Again, while in Switch X, I can do a CDP neighbor and see switch B. But I cannot SSH from switch X to Switch B, or any other devices that I tried. Now, we did find a config error with VTP; the VTP domain name was different. But VTP has nothing to do with SSH. Just to placate my co-workers, I went ahead and renamed the VTP domain name (it's running transparent mode). After I regenerated the crypto key, I saved everything of course. I then reloaded the switch. When all came back up, I still could not SSH
This is a 3560 switch, and it is trunk to a 3750.
View 13 Replies
View Related
Jan 2, 2013
I am slowly working my way though the setup and configuration of our new 4900m switch. The switch will have a pretty basic operational configuration. We are simply going to network 3 servers together through the swtich. Anyhow, I have been fallowing the guide at this site: [URL]
Basically the switch is brand new and I just setup things such as the clock, the banner, and the hostname. Anyhow, at various points in the guide such as the configuration of the telnet password and especially the interface gigabitethernet I get the "invalid input detected at '^' marker". I also did a show interfaces and noticed there was not any gigabitethernet interfaces but there was a
"FastEthernet1 is down, line protocol is down Hardware is Fast Ethernet for out of band management, address i"
Anyhow, my thinking is continuing on with the guide and at least try to setup the interface for the management port so I can then use the cisco network assistant gui to then configure the rest of the switch.
View 1 Replies
View Related
Apr 4, 2013
Do I need to run any special license (like IP SERVICES) on the Cisco Catalyst 4900M in order to run VRF lite?
View 4 Replies
View Related
Jan 9, 2012
I'm setting up a new 4900m running cat4500e-ipbase-mz.122-53.SG5.bin. I'm attempting to create Port-Channels as a Trunk for uplink to a 4503 running cat4500-ipbase-mz.122-37.SG1.bin.When I attempt the command "switchport trunk encapsulation dot1q" it errors out.
View 3 Replies
View Related
Feb 18, 2013
We are facing issue with highly frequent interface flaps on Cisco 4900M switch only for module WS-X4920-GB-RJ45. Strange thing is no complaint from the users/server teams for any traffic interruption.
Switch: Cisco WS-C4900M
Line card: WS-X4920-GB-RJ45
IOS image is cat4500e-ipbase-mz.122-53.SG4.bin
There are several other smilar model & linecard/inventory of switches with exactly same IOS image, however there are no issues with them.
View 5 Replies
View Related
Nov 6, 2012
There are two Cisco 4900M L3 switches and two Cisco 2960 L2 switches. I need to configure the two L3 switches to operate as a redundant pair, as the servers connecting to them are connecting using bonded interfaces, which can only have one default gateway. So these two L3 switches need to have the same Vlan interface 1, 2 and 3 IP's set onto them.How are the two L3 switches made aware of each other? via a normal trunk? Is there some special configration for configuring a mated/redundant pair of switches? or are they both just configured as though they were the same switch, but linked?
View 14 Replies
View Related
