Cisco Switching/Routing :: Catalyst 4900M Switch Stackable
Feb 2, 2012Would like to know if the Cisco Catalyst 4900M Switches are stackable?
View 2 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Catalyst 4900m With TwinGigi Converter?
May 23, 2012Got a question for 4900m with TwinGigi Converter. I bought couple TwinGigi Convert thinking to use it on fix module ports (8 * 10G ports on 4900m ten1/1 to 1/8). I follow TwinGigi configuration guide [URL]however, I am getting Invalid commands on hw-module:
Switch(config)#hw-module module 1 ?
logging Logging
Switch(config)#hw-module module 2 ?
logging Logging
power Enable/disable power to module in specified slot
[code]...
here is show ver and show mod:
Switch#show ver
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-IPBASEK9-M), Vers
ion 15.0(2)SG2, RELEASE SOFTWARE (fc3)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 07-Dec-11 20:20 by prod_rel_team
[code]...
Cisco Switching/Routing :: Any Special License On Catalyst 4900M In Order To Run VRF Lite?
Apr 4, 2013Do I need to run any special license (like IP SERVICES) on the Cisco Catalyst 4900M in order to run VRF lite?
View 4 Replies View RelatedCisco Switching/Routing :: How To Setup SPAN On 4900m Switch
Feb 12, 2013I currently have IOS image cat4500e-entservices-mz.122-53.SG5.bin. According to my research it appears SPAN is supported on this OS. However, after looking at procedure notes using websites like here:
[url]... I cannot find and obviously not figure out how to use the SPAN command. My main objective is to simply setup a port mirror on one of my TenGigabitEthnet interfaces and from what I read SPAN is the best way to setup a tap interface on a cisco switch.
Cisco Switching/Routing :: 4900m Switch Enable HTTP
Jan 6, 2013I have been trying to get the http server enabled so I can access Cisco Network Assistant. I have my interfaces configured but for some reason the server in not running, port 80 is still closed. [code]
View 2 Replies View RelatedCisco Switching/Routing :: Perform Initial Configuration Of 4900m Switch?
Jan 2, 2013I am slowly working my way though the setup and configuration of our new 4900m switch. The switch will have a pretty basic operational configuration. We are simply going to network 3 servers together through the swtich. Anyhow, I have been fallowing the guide at this site: [URL]
Basically the switch is brand new and I just setup things such as the clock, the banner, and the hostname. Anyhow, at various points in the guide such as the configuration of the telnet password and especially the interface gigabitethernet I get the "invalid input detected at '^' marker". I also did a show interfaces and noticed there was not any gigabitethernet interfaces but there was a
"FastEthernet1 is down, line protocol is down Hardware is Fast Ethernet for out of band management, address i"
Anyhow, my thinking is continuing on with the guide and at least try to setup the interface for the management port so I can then use the cisco network assistant gui to then configure the rest of the switch.
Cisco Switching/Routing :: 4900M - Establish Link Connection Between 10Gbase-T Server Nic And Switch
Jan 2, 2012I have an issue with a Cisco 4900M switch with a WS-X4908-10G-RJ45 half card. The link connection between a 10Gbase-T server nic and the switch does not establish, i believe it is an auto negotiation problem. The link fluctuates constantly between connected and disconnected when set to auto negotiate. When the 10G half card port groups are configured for 1G connections it does the same. If i hard code the server nic to 1G the link remains up when the port group is at 1G. If i hard code the server nic to 10G the link stay down, i don't think the port speed and duplex can be hard coded on the switch end. I have tried updating the drivers on the server as well as diagnostic tests on the nic, which passed. The 4900M IOS code is version 15.0.2-SG2. If i plug a laptop into the 1G configured port the switch and the laptop negotiate at 1G. Also, i believe, if the 10G server nic is plugged into another 1G only switch the link auto negotiates to 1G as normal. The server nic is an INTEL Server Adapter AT 10G, which became end of life in 2009. I believe the half card came out in 2010.
View 5 Replies View RelatedCisco Switching/Routing :: Catalyst 4006 / Quickly Copy Configuration From Production Switch To Spare Switch?
Nov 20, 2009I have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies View RelatedCisco Switching/Routing :: Inter-VLan Routing On Catalyst 3750 Switch
Dec 17, 2011I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
Cisco Switching/Routing :: 4948 Supported Stackable?
May 23, 2012MAC Support: 16000
Backplane: 18Gbps
Forward: 28Gbps
VLAN's: 4000 (q-in-q support)
Jumbo Frame Supported
Supported 8000 static routing
!Supporting Stack!
Cisco 4948 supporting stackable? which product do you recommend to these criteria?
Cisco Switching/Routing :: Are Non-S 2960 Switches Stackable
Jul 5, 2012Are the non-S series 2960 switches stackable or are they only able to be uplinked?
View 6 Replies View RelatedCisco Switching/Routing :: About Intervlan Routing On Catalyst 3750 Switch
Apr 16, 2012I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies View RelatedCisco Switching/Routing :: Can't SSH Into New Catalyst 2960 Switch
Jun 13, 2012I'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
Cisco Switching/Routing :: Catalyst 2960 Switch Qos
Aug 20, 2012i try to implement layer 2 qos in 2960. when i complete to configure the switch, i want to test the qos.PC1 conect to switch port 1,PC2 conect to switch port 2 . PC1 is source teminal. i use skydata.exe and FTP for the test.
when use the skydata ,the PC2 speed can reach 10mbps.when use the FTP , the PC2 only can reach 1.2mbps. why?
Cisco Switching/Routing :: Can't SSH Into New Catalyst 2960-S Switch
Apr 29, 2012I can use Putty to SSH into my new switch (Directly connected to my laptop with ethernet cable), but I cant log into my switch.
Sent username "admin"
admin@192.168.251.1's password:
Access denied
It doesnt like my password, but I have only set 1 password (king) on this switch. I've configured 3 other switches with SSH and had no problem. Been trouble shooting for awhile and It'd be great if I could have a 2nd set of eyes take a peek, Also, my running config is attached.
Cisco Switching/Routing :: 3570 Stackable Switches Models
Jun 23, 2012I want to be sure for this before ordering: is the Enterprise-class stackable switches "WS-C3750X-48T-S" model can be stackable with "WS-C3750G-48TS" model.
View 5 Replies View RelatedCisco Switching/Routing :: 3750 Stackable Switches Uplink
Nov 14, 2011If I have two stackable switches one that connects to the 6509 core switch and the other switch does not, do I have to uplink the switch to the other switch so that switch has route to the core switch or because the switches are daisy chain there is not need to cable one switch to to the other switch connected to core switch?
View 6 Replies View RelatedCisco Switching/Routing :: Connecting 3750 Stackable Switches
Nov 13, 2011If I have two switches in a stack can both stack able switches be connected to a core switch through gbics or just only one switch can be connected to the core and the other switch connects to the other stack able switch through an Ethernet port which uses as a gateway to the core switch?
View 3 Replies View RelatedCisco WAN :: Does Catalyst 4900m Support IP-SLA
Oct 30, 2011Catalyst 4900m does not support command "ip sla <entry-number>" like Catalyst 6500. If 4900 does support SLA, how to configure it then? [code]
View 4 Replies View RelatedCisco Switching/Routing :: Catalyst 2948G Switch Got Dead
Feb 15, 2012I had an old Cisco Catalyst 2948G switch that I have not used in about 7 years down in my basement. I powered it on and went through the process of clearing out the configurations, and I got to a point where one of the commands to clear out the config asked me to install jumpers for "ROM" and "ERASE". There is a third jumper labeled "NO BOOT". They are numbered J6, J7, & J8 respectivelyI found the jumpers inside and put the jumpers on them and ran the command expecting it to remove any old configurations I had on the switch and bring it back to factory state, but I was wrong.
View 3 Replies View RelatedCisco Switching/Routing :: PA-MC-2E1 / 120 Work With Catalyst Switch 6506E?
Dec 12, 2012Does the port adaptor PA-MC-2E1/120 work with the Catalyst Switch 6506E (Sup Engine: 720-3B)? We have bought a Enhanced FlexWAN card for this port adaptor.I read through the cisco website and seem to get confusing answers whether they are compatible.
View 1 Replies View RelatedCisco Switching/Routing :: Catalyst 2970 Switch For 2 Vlans
Oct 14, 2012I am using a catalyst 2970 switch for 2 vlans. Corporate data and a separate VLAN for backups. What I want to do is create an LACP etherchannel to the switch and also trunk these ports so the server is part of both VLANS.Due to fact that some of these servers are on totally separated networks, they really shouldn't be able to talk to the backup server. Creating the VLAN for backups works to achieve this. I plan to create inbound ACLs on each port to allow only the ports and IPs for the backup network and allow everything we need for corporate data.I read somewhere that you can't have ACLs on an etherchannel and I just want to get it all straightened out. I notice I can't add an access group to the port-channel itself but I can on the port- channel member ports. Is this all I need to do or does this not work?
View 1 Replies View RelatedCisco Switching/Routing :: Catalyst 2948G Switch Is Dead
Dec 10, 2012I had an old Cisco Catalyst 2948G switch that I have not used in about 7 years down in my basement. I powered it on and went through the process of clearing out the configurations, and I got to a point where one of the commands to clear out the config asked me to install jumpers for "ROM" and "ERASE". There is a third jumper labeled "NO BOOT". They are numbered J6, J7, & J8 respectivelyI found the jumpers inside and put the jumpers on them and ran the command expecting it to remove any old configurations I had on the switch and bring it back to factory state, but I was wrong. This switch runs CatOS, not IOS.When power is applied to the switch, the fans turn on as normal, but no LEDs are lit on the front. There are green LEDs lit next to the jumpers inside, but that is all. I am not able to get any response from it on the console at all anymore.The LEDs that are lit green inside are labeled "CR5" and CR6".
View 2 Replies View RelatedCisco Switching/Routing :: Unable To Mange 500 Catalyst Switch
Jun 8, 2013I have inhereted a network in a school that is using a Cisco Catalyst 500 series switch. Previously, it appears that this switch was never managed (just plugged in and using it's default configuration). I am trying to change that and be able to control the switch using the Network Assistant or just the web-based device manager. I understand that you cannot perform the initial configuration with anything past Windows XP, because the broadcast flag setting past XP causes an issue where the IP address of the management computer is assigned but not the default gateway. Despite this, I am still unable to connect to the switch for management purposes. Here is a list of the steps I have taken, all of which have been unsuccessful:
1) I tried using a computer running Windows XP. The same issue occurred. It was assigned an IP address from the switch but did not get a default gateway. It was unable to access what should have been the default IP of the switch; 169.254.0.1
2) I tried it in Windows Vista by editing the registry to turn broadcasting off. It still did not work.
3) I tried it in Windows 7. Still no luck.
4) In all 3 operating systems, I tried using the "Advanced" setting in the TCP/IP configuration to add a default gateway of 169.254.0.1 to no avail.
[URL]
Cisco Switching/Routing :: Catalyst 4500 As Layer 2 Switch But With VRF?
Oct 16, 2012is it possible to run a Catalyst 4500 as pure Layer 2 Switch, i.e. disabling "ip routing", but still managing the switch via Fa1, i.e. the defautl mgmtVrf vrf ?I tried the following:
!
no ip routing
!
interface FastEthernet1
ip vrf forwarding mgmtVrf
ip address 192.168.1.1 255.255.255.0
!
ip route vrf mgmtVrf 0.0.0.0 0.0.0.0 192.168.1.254
ip default-gateway 192.168.1.254
I was not able to reach the Switch even from the same subnet. Only after enabling ip routing I could manage the Switch. I haven't found any command to set ip default-gateway for a vrf. Any workaround to keep routing disabled, but still manageable via VRF?
Cisco Switching/Routing :: 4503 - Catalyst L3 Switch Model
Jan 9, 2012Currently we have cisco 4503 switch in one of our location without redundancy which servers below,
300 user (desktop & ip phones)
5 vlans
15 access switches are connected
one L3 connectivity.
Actually i want to understand is it really necessary to have 4503 or we can go for 4900 series as we are planning to have redundancy in distribution segment.
Which is the best L3 switch in the above scenario and how to measure the overall performance of the current 4503 switch...
Cisco Switching/Routing :: Catalyst 6500 Switch Architecture
Jul 16, 2012 one of the most widely deployed switches in the world. The "Swiss Army knife of network", can do routing, switching, security, wireless and almost everything that you would want your core switch to do. Remember to use the rating system to let Akshay know if you have received an adequate response.
Akshay might not be able to answer each question due to the volume expected during this event. Remember that you can continue the conversation on the Network Infrastructure sub-community LAN, Switching and Routing discussion forum shortly after the event. This event lasts through July 27, 2012. Visit this forum often to view responses to your questions and the questions of other community members.
Cisco Switching/Routing :: 3750X / IP Base And IP Services Stackable Switches?
Aug 16, 2012I'm building a wired closet to aggregate user's connections, Im planning to have 5x 3750X stacked switches and there is a need to run EIGRP, I'm thinking to order one switch with IP service image while the rest will run IP base image, is it workable scenario and what are the drawbacks of such combination of images ?
View 5 Replies View RelatedCisco Switching/Routing :: 2960 Stackable Switches Instead Of One 4500 Series?
Dec 11, 2011I have a design for my infrastructure and i'm thinking to choose 4 or 5, or more, 2960 series in a stack mode instead of one 4500 series?
View 6 Replies View RelatedCisco Switching/Routing :: Feature Request For 3750s And Other Stackable Switches?
May 6, 2013can you stack a 3750 switch over fiber.....the answer is no, but the virtual switching supervisor 720-10G for the 6500 can create one virtual switch using two 6500s...
how can we get cisco to come up with a way for access switches to be stacked over fiber similar to above supervisor? i know of few of my site that would benefit from this...maybe they can come up with a vss appliance, similar to a media converter, to convert stackwise over fiber...then of course, you would need the same appliance on the other end....
Cisco Switching/Routing :: Enable / Disable OID's In Catalyst 3750-X Switch
Feb 19, 2013In my ongoing project i need to monitor cisco 3750-X port status (uplink/downlink) i.e. whenever there is some problem at a specific port. I need to monitor it through an OPC server and right now what i am doing is as follows: i am using Kepserver and i have added SNMP driver in it for that purpose i am not a networking expert but what i have learnt till now is that SNMP agent (that resides in switch) delivers the status of MIBs to SNMP manager ( which in my case is kepserver (opc server)) for the above purpose i am adding IF-MIB to monitor OID 1.3.6.1.2.1.2.2.1.8 (which shows port statuses) but when i add that in OPC server then it indicated that this OID is not available in the Switch ( it might be disabled) so i need to ask if there is any way to enable OID's in a switch,
View 0 Replies View RelatedCisco Switching/Routing :: Download IOS To Flash In Switch Catalyst 2960?
Jan 23, 2013In a switch catalyst 2960 the IOS is erasing in flash, for the transfer IOs respalding to flash no function the current command. how is the method.
View 6 Replies View RelatedCisco Switching/Routing :: Catalyst 3750X-48P Switch Ports Dead
Jan 31, 2012I work at a hospital and we have 3750X-48P switches in stacks in various locations throughout the hospital. We have noticed that when an EKG machine is plugged into one of the ports on some of these switches and the EKG machines are set manually to 100/Full, the ports are no longer usable until the switch is restarted. The switch is configured for auto. If the EKG machine is set to auto, it will work and not cause problems. The link on the interface will show up/up and there will be output packets increasing. However, there will be no inputs on the link and the port is unusable. Unfortunately, even when the device is removed, the port becomes unusable for any device. Is there any way to fix this problem without rebooting the switch?
View 5 Replies View Related