Cisco WAN :: Functionality Difference In Supervisor Engine 2 / 2T For Catalyst 6500?
Aug 10, 2012Is there functionality difference in Supervisor Engine 2 and Supervisor Engine 2T for Catalyst 6500 ?
View 3 Replies
ADVERTISEMENT
Cisco Infrastructure :: Supervisor Engine Catalyst 6500 Modular IOS?
Oct 11, 2011I want to know the difference between the software that is Modular and the one that is not. What are the pros and cons ?
CAT6000-SUP32 IOS ADVANCED IP SERVICES SSH or CAT6000-SUP32 IOS ADVANCED IP SERVICES SSH (MODULAR)
Cisco Switching/Routing :: 6513 / Difference Between Supervisor Engine 720 Active And Hot Status?
Apr 19, 2013In my 6513 switch chassis we have two Supervisor Engines 720 one is marked Active other as Hot. what is the diffrence in their mode as by name I suppose that Active one is currently in use and Hot one is in standby mode.They are showing in this manner.
Module Ports Card Type
7 2 Supervisor Engine 720 (Active)
8 2 Supervisor Engine 720 (Hot)
Cisco WAN :: Catalyst 4500 E-Series Supervisor Engine 7L-E?
Aug 12, 2012I have a strange issue with 4500 E chassis loaded with SUP 7L-E which always remains in ORANGE LED status, also the uplink ports interface is down and the line protocol is down but when i execute the command sh int gig1/5 it show me the media type sfp but there is no red laser light seen in the sfp transiever,The below command is configured for the uplink gig port on the SUP engine.hw-module uplink select gigabitethernet?
View 10 Replies View RelatedCisco Switching/Routing :: Catalyst 4006 Supervisor Engine Led Red
Nov 28, 2011we got a problem with our cat4006 coreswitch. The led on the supervisorengine is red, and several errors are appearing in the message log. [code]
View 1 Replies View RelatedCisco Switching/Routing :: Catalyst 6509-E / Replace Supervisor Engine 720 10GE
May 15, 2012we have Supervisor Engine 720 10GE (VS-S720-10G) in slot 5 on Catalyst 6509-E. Slot 6 is free. We need to replace VS-S720-10G. Is it possible the following scenario
1. we will insert new VS-S720-10G into the slot 6
2. then we will remove the faulty VS-S720-10G from the slot 5
Will everything work without interuptions. Is any document where I can find step-by-step procedure how to replace VS-S720-10G ?
Cisco Switching/Routing :: 6500 Redundant Supervisor Engine Will Forward Data While Is Standby
Oct 26, 2011We bought Cisco sup engine WS-SUP32-GE-3B for 6500 switches 2 nos for redundancy. I have connected 6 systems on each sup engine ports. How to clarify whether both sup engine will forward the data while one is Master and other is standby?
View 4 Replies View RelatedCisco Switching/Routing :: Catalyst 4500E Supervisor Engine 7-E / Possible To Deploy Simultaneously Both Type Of Ports
Aug 8, 2012We've got a doubt about the uplink ports of this supervisor. I've read that you have to use the four ports in 10G mode or in 1G mode, but not use for example 1 port in 10G mode and 1 port in 1G mode:
But, you can read in another sentence: " Beginning with Cisco IOS Release 12.2(25)SG, you could simultaneously deploy the dual 10-Gigabit.Ethernet ports and the four Gigabit Ethernet SFP ports on the Catalyst 4503, Catalyst 4506, and Catalyst 4507R chassis." Is it posible deploy simultaneously both type of ports?
Cisco Switching/Routing :: Catalyst 6500 / QoS For Supervisor 2T?
Apr 30, 2013I need to configure QoS (voice and video) for Catalyst 6500 series switches with Supervisor 2T modules and DFC4 linecards.
Is this radically different from what we do int he Sup32 and 720s? I was looking at some templates online, such as
[URL]
But I don't see anything for the new Supervisor 2T?
Cisco Switching/Routing :: Catalyst 6500 Dual-Supervisor 720-10G-3C?
Sep 21, 20121. We now have SupA & SupB in the chassis, due to some mistake we have same IOS version but different feature set on them, although we configured redundancy mode sso, in the "show redundancy" we see Operating Redundancy Mode = rpr due to Software mismat, we now need to fix them as same feature set image, if I use "copy sup-bootdisk0:/xxxx slavesup-bootdisk0:/xxx", then write memory, does this cause any service/network interuption?
Available system uptime = 1 year, 1 week, 4 days, 9 hours, 21 minutes
Switchovers system experienced = 2
Standby failures = 0
Last switchover reason = active unit removed
[code]....
2. We did a failover test with this status, found that if we triggered supervisor failover, all modules will reload thus the services if interupped. How about after we make the Operating Redundancy Mode as sso, will this behaviour shows again? Or a stateful failover will happens, then modules no need reload?
3. We are using OSPF as our L3 routing protocol, after reference to the configuration, nsf should be enabled, we want to ask in the OSPF-domain nsf should be configured in all OSPF-enabled router or only 6500 which have dual-sup?
4. We also found that the interfaces(3 * Gig & 2 * TenG) in Standby supervisor cannot be use even enabled & configured, is it because we are running rpr mode now or will be the same even change to sso? Before customer have some older supervisor in 6500 non-e chassis, and they can use the standby supervisor interfaces as traffic forwarding, they use rpr-plus mode before, how about in sso mode?
Cisco Switching/Routing :: Does Supervisor 720 Support All Existing Catalyst 6500 Series Interface
Feb 12, 2013Q. Does the Supervisor 720 support all existing Cisco Catalyst 6500 series interface and services module, protecting customer investments?
View 1 Replies View RelatedDistributed Forwarding Card For Supervisor Engine 2T
Dec 23, 2011I was looking to 6500 series switches. I saw DFC4 module (WS-F6K-DFC4-A, WS-F6K-DFC4-AXL) and (WS-F6K-DFC4-E, WS-F6K-DFC4-EXL). Data sheet for supervisor engine 2T wrote that for maximum performance you should DFC4. I'm a bit confused. I didn't any useful information about it:
1. DFC4 is a separate module(consumes 1 slot)? Does it have any ports on it?
2. Is it a daughter card? If yes, should it be installed on supervisor or it should be installed on line cards?
Cisco Switching/Routing :: Supervisor Engine 720 Errors
Apr 18, 2013i have a standalone SUP720, no traffic is passing through it. only one port connected for remote telnet, its kind of backup device.today i checked its log, and there are some wiered message.is it a software bug or my SUP has gone bad? [code]
View 24 Replies View RelatedCisco WAN :: 7690 - Removing And Installing A Supervisor Engine
Dec 26, 2010Removing and Installing a Supervisor Engine on a cisco router 7690 and more important IOS upgrade of this module.
I need some kind of manual, but I would prefer a short procedure to do this change. A brief of the steps to do that. Also i don't if i have to upgrade the new module after install it.
PD.
IP7VAL02#sh modMod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1034Z32J 2 48 CEF720 48 port 10/100
[Code]....
Cisco Switching/Routing :: VSS With 4 Supervisor Engine 2T-10GE
May 6, 2013We have a scenario with 2 chassis, both with 2 supervisor Engine 2T, we try to make a configuration of VSS with the chassis and would link to know if is possible have 2 supervisor on chassis one and 2 supervisors on chassis 2 with VSS?
Router#sho switch virtual redundancy
My Switch Id = 1
Peer Switch Id = 2
Last switchover reason = active unit removed
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
[code]....
would like to use the second supervisors for obteind the local redundancy en chassis 1 and 2, this is possible?
the actually version on four supervisors is: s2t54-ipservicesk9-mz.SPA.150-1.SY3.bin
Cisco Switching/Routing :: 6509 How To Configure VSS With Two Different Supervisor Engine
Oct 1, 2012I have configured the VSS in two cisco 6509-E series with only one supervisor engine, but if i configured with two supervisor engine. it is going to common mode. One supervisor engine is 3c and 3cxl.
View 2 Replies View RelatedCisco Switching/Routing :: Upgrading Supervisor Engine On 4006?
Nov 3, 2011I have an older 4006 with a Supervisor II+. We now need OSPF support, which the Sup II+ does not provide. I have access to a Supervisor III (WS-X4014), which will provide OSPF support. Question is, are there any gotchas to shutting down the switch, replacing Supervisor Engines and then powering up? What about the flash card? On my current system, it appears that I am only using bootflash: , which is where the IOS resides (see below). Since my startup config is in nvram and my IOS is in bootflash, what's the purpose of the flash card in slot0: ? and where does NVRAM and bootflash actually live on a 4006 ( on the Supervisor Engine?)
sh bootvar
BOOT variable = bootflash:cat4500-ipbase-mz.122-31.SGA11.bin,1;,1;
CONFIG_FILE variable does not exist
BOOTLDR variable does not exist
[Code].....
Cisco Switching/Routing :: Supervisor Engine For 4003 Switch
Oct 24, 2012I buy a Cisco 4003 Switch with Supervisor Engine I but it only run CatOs and i whant it to run Cisco IOS so whitch Supervisor Engine can the Cisco 4003 Switch run? i have look at the Supervisor Engine III it can run Cisco IOS and Layer 3 but can i use that in my Cisco 4003 switch?
View 14 Replies View RelatedCisco Switching/Routing :: C6500 Bootdisk And Supervisor Engine
Apr 5, 2013For C6500 chassis, sup-fould like to know the dirrerence between supervisor engiene 720 sup-bootflash and sup-bootdisk?
View 3 Replies View RelatedCisco Switching/Routing :: 4500 Supervisor Engine Error
Mar 16, 2012On an existing 4500 switch with a single sup 6-E, another sup 6-E is added. But the second sup6-E comes up as synchronised with active and in a few minutes time, reloads again. the software is 12.2(44) is the same on both sup engines. the redundancy sso output shows that slot6 is disabled.
View 1 Replies View RelatedCisco Switching/Routing :: Core 4500 Series Supervisor Engine?
Jun 19, 2012Our company will go to buy a core switch 4503. What is the difference between the Catalyst 4500 E-Series Supervisor 7L-E and the Catalyst 4500 E-Series Supervisor 7-E?
View 1 Replies View RelatedCisco Switching/Routing :: Standby Supervisor Engine Not Sync In 4507R?
Dec 26, 2012When i have configured the 4507R switch but the configure is not sync with the standby module..... I have doing some troubleshooting
1. type the command "show redundancy" no standby module is showing
2. type the command " redundancy force-switchover" showing the message " no standby module is present"
3. type the command "hw-module module 2 reset" then the standby module is reset and status light is blinking like it is booting..
Cisco Switching/Routing :: 4507R Supervisor Engine IV X4515 Not Booting
Dec 5, 2011I have a 4507R with a WS-X4515 supervisor V. It was booting into rommon mode, so I attempted to boot to an IOS image from TFTP. The boot process hangs at at the end of the below output and the then the status light blinks orange. I left it sit like this overnight, and it remained the same.
rommon 23 >boot tftp://x.x.x.x/cat4500-entservicesk9-mz.122-53.SG2.bin
Tftp Session details are ....
Filename : /cat4500-entservicesk9-mz.122-53.SG2.bin
[Code]......
Cisco Switching/Routing :: 4507R Configuring Supervisor Engine Redundancy
Feb 14, 2012How to configure Supervisor Engine Redundancy between two different cisco 4507R and 4506E.
View 5 Replies View RelatedCisco Switching/Routing :: 6513 - Redundant Supervisor Engine 720-3B Reloads
Sep 1, 2010There is a Cisco Catalyst 6513 in my office. Recently we decided to setup redundant Supervisor Engine 720-3B. When we did it, its became STANDBY COLD, and then it reloads. IOS is equal on both supervisors. It must be STANDBY HOT (SSO) redundancy. There is a configuration and show ver and show module outputs, and log of my actions.
View 3 Replies View RelatedCisco Switching/Routing :: Run VSS On 6513 / 6509 Considering Both Has Same Supervisor Engine 2T And IOS Image
Jun 25, 2012Is it possible to run VSS on 6513 and 6509 when considering both has same supervisor engine 2T and same IOS image.
View 1 Replies View RelatedCisco Switching/Routing :: 2690 - SFP Ports On Active And Standby Supervisor Engine
Oct 19, 2012We are expanding out LAN network with more 2960 access switches. All the access switches are suppose to be connected to core switch (4507R) but i have less port on the core switch.
On the core switch we have two supervisor engines (WS-X4515 ---description : "Supervisor IV with 2 1000BaseX GBIC ports"). I can see that on each supervisor engine i have two 1 GB SFP ports available and if i calculate for two supervioser engine i will have 4 1GB ports.
But at particular time only one supervisor engine is active and other is in standby mode (redundancy mode used is SSO between two SUP engines).
Can i used all 4 SFP ports for connecting 4 uplinks to the 4 access switch?Will all the 4 SFP ports active at one time or only 2 SFP ports will be active that is for only active supervisor engine.
Cisco Switching/Routing :: Catalyst 3850 - Additional License To Enable Controller Functionality?
Feb 10, 2013Based on what i am reading on the Catalyst 3850 datasheet, the controller functionality comes by default if i have a IP Base of IP Services license on the switch. Is this correct or do i need additional license to enable the controller functionality?What capabilities does below license provide ?
LIC-CT3850-UPG (Primary upgrade license SKU for Cisco 3850 wireless controller)
Cisco WAN :: Supervisor Redundancy For The 6500?
May 14, 2012We currently have the following configuration:
STB_6509#sho mod
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 10 WiSM WLAN Service Module WS-SVC-WISM-1-K9
2 24 CEF720 24 port 1000mb SFP WS-X6724-SFP
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B
[code]....
I would like to add a redundant supervisor blade to the 6509 that is in production. Can this be done plug and play and require no reload. Are all WS-SUP720-3B the same as far as memory etc... or can I buy any used WS-SUP720-3B and it will work properly.
Cisco Routing :: Catalyst 6500 / 4500 - Preventative Maintenance On Catalyst Chassis Switches?
Jun 4, 2013Are there any best practices for preventative maintenance on Catalyst Chassis switches. Looking to build a PMI schedule for a customer. Or is there evidence not to perform it at all. Things like re-seating line cards, cleaning fan exhausts, etc.
View 1 Replies View RelatedCisco WAN :: Can IOS Be Installed On Catalyst 2901 Switch With Sup Engine
Jan 22, 2011I have Cisco Catalyst 2901 switch with Sup engine which have CatOS installed. I want to know that can I install Cisco IOS in this switch.
View 1 Replies View RelatedCisco Switching/Routing :: 6500 What Happens When A Supervisor Fails
Feb 3, 2010We've been mocking up a test lab to test VSS on two 6500's. Each 6500 has one sup720 and a 6708-10ge blade and we've established the two 10ge links between the two chassis; the first from the each chassis' sup and the second from each 6708.My question is, what happens when the supervisor fails on one of the chassis?
View 10 Replies View RelatedCisco Switching/Routing :: QoS Catalyst 4500 7E Supervisor
Apr 15, 2012I am trying to understand the implicit limit to the priority queue. I know you can define an explicit policer but if you don't I can't find out what the rate limit really is.
View 5 Replies View Related