Cisco Switching/Routing :: C6500 Bootdisk And Supervisor Engine
Apr 5, 2013For C6500 chassis, sup-fould like to know the dirrerence between supervisor engiene 720 sup-bootflash and sup-bootdisk?
View 3 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Supervisor Engine 720 Errors
Apr 18, 2013i have a standalone SUP720, no traffic is passing through it. only one port connected for remote telnet, its kind of backup device.today i checked its log, and there are some wiered message.is it a software bug or my SUP has gone bad? [code]
View 24 Replies View RelatedCisco Switching/Routing :: VSS With 4 Supervisor Engine 2T-10GE
May 6, 2013We have a scenario with 2 chassis, both with 2 supervisor Engine 2T, we try to make a configuration of VSS with the chassis and would link to know if is possible have 2 supervisor on chassis one and 2 supervisors on chassis 2 with VSS?
Router#sho switch virtual redundancy
My Switch Id = 1
Peer Switch Id = 2
Last switchover reason = active unit removed
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
[code]....
would like to use the second supervisors for obteind the local redundancy en chassis 1 and 2, this is possible?
the actually version on four supervisors is: s2t54-ipservicesk9-mz.SPA.150-1.SY3.bin
Cisco Switching/Routing :: 6509 How To Configure VSS With Two Different Supervisor Engine
Oct 1, 2012I have configured the VSS in two cisco 6509-E series with only one supervisor engine, but if i configured with two supervisor engine. it is going to common mode. One supervisor engine is 3c and 3cxl.
View 2 Replies View RelatedCisco Switching/Routing :: Upgrading Supervisor Engine On 4006?
Nov 3, 2011I have an older 4006 with a Supervisor II+. We now need OSPF support, which the Sup II+ does not provide. I have access to a Supervisor III (WS-X4014), which will provide OSPF support. Question is, are there any gotchas to shutting down the switch, replacing Supervisor Engines and then powering up? What about the flash card? On my current system, it appears that I am only using bootflash: , which is where the IOS resides (see below). Since my startup config is in nvram and my IOS is in bootflash, what's the purpose of the flash card in slot0: ? and where does NVRAM and bootflash actually live on a 4006 ( on the Supervisor Engine?)
sh bootvar
BOOT variable = bootflash:cat4500-ipbase-mz.122-31.SGA11.bin,1;,1;
CONFIG_FILE variable does not exist
BOOTLDR variable does not exist
[Code].....
Cisco Switching/Routing :: Catalyst 4006 Supervisor Engine Led Red
Nov 28, 2011we got a problem with our cat4006 coreswitch. The led on the supervisorengine is red, and several errors are appearing in the message log. [code]
View 1 Replies View RelatedCisco Switching/Routing :: Supervisor Engine For 4003 Switch
Oct 24, 2012I buy a Cisco 4003 Switch with Supervisor Engine I but it only run CatOs and i whant it to run Cisco IOS so whitch Supervisor Engine can the Cisco 4003 Switch run? i have look at the Supervisor Engine III it can run Cisco IOS and Layer 3 but can i use that in my Cisco 4003 switch?
View 14 Replies View RelatedCisco Switching/Routing :: 4500 Supervisor Engine Error
Mar 16, 2012On an existing 4500 switch with a single sup 6-E, another sup 6-E is added. But the second sup6-E comes up as synchronised with active and in a few minutes time, reloads again. the software is 12.2(44) is the same on both sup engines. the redundancy sso output shows that slot6 is disabled.
View 1 Replies View RelatedCisco Switching/Routing :: Core 4500 Series Supervisor Engine?
Jun 19, 2012Our company will go to buy a core switch 4503. What is the difference between the Catalyst 4500 E-Series Supervisor 7L-E and the Catalyst 4500 E-Series Supervisor 7-E?
View 1 Replies View RelatedCisco Switching/Routing :: Standby Supervisor Engine Not Sync In 4507R?
Dec 26, 2012When i have configured the 4507R switch but the configure is not sync with the standby module..... I have doing some troubleshooting
1. type the command "show redundancy" no standby module is showing
2. type the command " redundancy force-switchover" showing the message " no standby module is present"
3. type the command "hw-module module 2 reset" then the standby module is reset and status light is blinking like it is booting..
Cisco Switching/Routing :: 4507R Supervisor Engine IV X4515 Not Booting
Dec 5, 2011I have a 4507R with a WS-X4515 supervisor V. It was booting into rommon mode, so I attempted to boot to an IOS image from TFTP. The boot process hangs at at the end of the below output and the then the status light blinks orange. I left it sit like this overnight, and it remained the same.
rommon 23 >boot tftp://x.x.x.x/cat4500-entservicesk9-mz.122-53.SG2.bin
Tftp Session details are ....
Filename : /cat4500-entservicesk9-mz.122-53.SG2.bin
[Code]......
Cisco Switching/Routing :: 4507R Configuring Supervisor Engine Redundancy
Feb 14, 2012How to configure Supervisor Engine Redundancy between two different cisco 4507R and 4506E.
View 5 Replies View RelatedCisco Switching/Routing :: 6513 - Redundant Supervisor Engine 720-3B Reloads
Sep 1, 2010There is a Cisco Catalyst 6513 in my office. Recently we decided to setup redundant Supervisor Engine 720-3B. When we did it, its became STANDBY COLD, and then it reloads. IOS is equal on both supervisors. It must be STANDBY HOT (SSO) redundancy. There is a configuration and show ver and show module outputs, and log of my actions.
View 3 Replies View RelatedCisco Switching/Routing :: Run VSS On 6513 / 6509 Considering Both Has Same Supervisor Engine 2T And IOS Image
Jun 25, 2012Is it possible to run VSS on 6513 and 6509 when considering both has same supervisor engine 2T and same IOS image.
View 1 Replies View RelatedCisco Switching/Routing :: Catalyst 6509-E / Replace Supervisor Engine 720 10GE
May 15, 2012we have Supervisor Engine 720 10GE (VS-S720-10G) in slot 5 on Catalyst 6509-E. Slot 6 is free. We need to replace VS-S720-10G. Is it possible the following scenario
1. we will insert new VS-S720-10G into the slot 6
2. then we will remove the faulty VS-S720-10G from the slot 5
Will everything work without interuptions. Is any document where I can find step-by-step procedure how to replace VS-S720-10G ?
Cisco Switching/Routing :: 6513 / Difference Between Supervisor Engine 720 Active And Hot Status?
Apr 19, 2013In my 6513 switch chassis we have two Supervisor Engines 720 one is marked Active other as Hot. what is the diffrence in their mode as by name I suppose that Active one is currently in use and Hot one is in standby mode.They are showing in this manner.
Module Ports Card Type
7 2 Supervisor Engine 720 (Active)
8 2 Supervisor Engine 720 (Hot)
Cisco Switching/Routing :: 2690 - SFP Ports On Active And Standby Supervisor Engine
Oct 19, 2012We are expanding out LAN network with more 2960 access switches. All the access switches are suppose to be connected to core switch (4507R) but i have less port on the core switch.
On the core switch we have two supervisor engines (WS-X4515 ---description : "Supervisor IV with 2 1000BaseX GBIC ports"). I can see that on each supervisor engine i have two 1 GB SFP ports available and if i calculate for two supervioser engine i will have 4 1GB ports.
But at particular time only one supervisor engine is active and other is in standby mode (redundancy mode used is SSO between two SUP engines).
Can i used all 4 SFP ports for connecting 4 uplinks to the 4 access switch?Will all the 4 SFP ports active at one time or only 2 SFP ports will be active that is for only active supervisor engine.
Cisco Switching/Routing :: 6500 Redundant Supervisor Engine Will Forward Data While Is Standby
Oct 26, 2011We bought Cisco sup engine WS-SUP32-GE-3B for 6500 switches 2 nos for redundancy. I have connected 6 systems on each sup engine ports. How to clarify whether both sup engine will forward the data while one is Master and other is standby?
View 4 Replies View RelatedCisco Switching/Routing :: Catalyst 4500E Supervisor Engine 7-E / Possible To Deploy Simultaneously Both Type Of Ports
Aug 8, 2012We've got a doubt about the uplink ports of this supervisor. I've read that you have to use the four ports in 10G mode or in 1G mode, but not use for example 1 port in 10G mode and 1 port in 1G mode:
But, you can read in another sentence: " Beginning with Cisco IOS Release 12.2(25)SG, you could simultaneously deploy the dual 10-Gigabit.Ethernet ports and the four Gigabit Ethernet SFP ports on the Catalyst 4503, Catalyst 4506, and Catalyst 4507R chassis." Is it posible deploy simultaneously both type of ports?
Distributed Forwarding Card For Supervisor Engine 2T
Dec 23, 2011I was looking to 6500 series switches. I saw DFC4 module (WS-F6K-DFC4-A, WS-F6K-DFC4-AXL) and (WS-F6K-DFC4-E, WS-F6K-DFC4-EXL). Data sheet for supervisor engine 2T wrote that for maximum performance you should DFC4. I'm a bit confused. I didn't any useful information about it:
1. DFC4 is a separate module(consumes 1 slot)? Does it have any ports on it?
2. Is it a daughter card? If yes, should it be installed on supervisor or it should be installed on line cards?
Cisco WAN :: 7690 - Removing And Installing A Supervisor Engine
Dec 26, 2010Removing and Installing a Supervisor Engine on a cisco router 7690 and more important IOS upgrade of this module.
I need some kind of manual, but I would prefer a short procedure to do this change. A brief of the steps to do that. Also i don't if i have to upgrade the new module after install it.
PD.
IP7VAL02#sh modMod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1034Z32J 2 48 CEF720 48 port 10/100
[Code]....
Cisco WAN :: Catalyst 4500 E-Series Supervisor Engine 7L-E?
Aug 12, 2012I have a strange issue with 4500 E chassis loaded with SUP 7L-E which always remains in ORANGE LED status, also the uplink ports interface is down and the line protocol is down but when i execute the command sh int gig1/5 it show me the media type sfp but there is no red laser light seen in the sfp transiever,The below command is configured for the uplink gig port on the SUP engine.hw-module uplink select gigabitethernet?
View 10 Replies View RelatedCisco Infrastructure :: Supervisor Engine Catalyst 6500 Modular IOS?
Oct 11, 2011I want to know the difference between the software that is Modular and the one that is not. What are the pros and cons ?
CAT6000-SUP32 IOS ADVANCED IP SERVICES SSH or CAT6000-SUP32 IOS ADVANCED IP SERVICES SSH (MODULAR)
Cisco WAN :: Functionality Difference In Supervisor Engine 2 / 2T For Catalyst 6500?
Aug 10, 2012Is there functionality difference in Supervisor Engine 2 and Supervisor Engine 2T for Catalyst 6500 ?
View 3 Replies View RelatedCisco Switching/Routing :: C6500 / MPLS Campus LAN Virtualization And VSS?
Apr 21, 2010I'm going to start the evaluation of implementing the virtualization of our campus LAN using MPLS.We'll get many inter-VLAN routing domains per VRF on the same LAN infrastructure.The LAN infrastructure is based on C6500 implementing VSS.Do you have experience with this kind of setup?Any known/faced issue that might prevent the setup of MPLS on VSS enabled C6500?
View 4 Replies View RelatedCisco Switching/Routing :: C6500 - Heat Dissipation With Or Without Transceivers?
Apr 13, 2013how is calculated heat dissipation of ethernet modules for c6500? For example, heat dissipation of WS-X6908-10G-2T - 2083.32 BTU/hour.. This heat dissipation of the empty module, without transceivers? Or including all installed transceivers?
View 3 Replies View RelatedCisco Switching/Routing :: C6500 Packets Don't Get Hardware Switches
Oct 23, 2011My C6500 is having relatively high CPU (no spikes, but constantly)
I'm under the impression that cef is causing this problem because alot of packets are being processed or send to/from the CPU. [code]
I did a netdr and I can see that the majority of packets going to the CPU are packets for which I have an entry in the CEF table.What can be a reason why those packets don't get hardware switches?I'm running Version 12.2(33)SXH5 - Sup720-10G.
Cisco Switching/Routing :: C6500 QoS - Link Between Internal DSCP And CoS Value
Sep 6, 2012there is something I find strange on C6500 about QoS: C6500 derive an internal DSCP value for it's internal use, but when configuring the qos mapping on output interfaces, only a cos value (I guess, an internal cos value) can be used. Is it a misunderstanding from me, or is it really illogic?
View 2 Replies View RelatedCisco Switching/Routing :: How To Configure IP Cache Flow On C6500
Nov 28, 2012I want to see net flow data.I have configured this command on the c6500.but I can to see data only below...How can I configration ip cache flow on the C6500? what is the problem?
int gi4/31
ip add x.x.x.x
ip route-cache flow
c6500# show ip cache flow
Displaying software-switched flow entries on the MSFC in Module 5:
[code].....
Cisco Switching/Routing :: C6500 / SNMP-server Traps For ISDN?
May 17, 2012Trying to migrate the config run on IOS 12.1 to 12.2 ?It seems there's no snmop traps isdn command support on 12.2.
where i can enable trap on ISDN over IOS 12.2 (33) sxj1 running on C6500 chassis?
Cisco Switching/Routing :: C6500 Filter ARP Answer On 802.1q Port For Specific VLan
Oct 10, 2012I am trying to filter ARP answer arriving on a C6500 trunk port, for a specific vlan.Filtering conditions are:
- packet arrive from vlan ID x on the trunk (on only for this vlan ID)
- source MAC address = xx:xx:xx:xx:xx:xx
Thae aim is that the C6500 with never enter into its CAM table this MAC address.I looked at several methos like service policy or vlan filter, but no solution for the moment.
Cisco Switching/Routing :: 6509 / 4900 - Network Down Cause Switching Supervisor With Redundancy
Jan 11, 2012we've had an issue with our network, we have 2 6509 connected with redundancy, which are connected with 2 x 4900 Switches, from which are connected to a ESX Chassis for visualization, the thing is that the ESX stopped working, and the 4900 switches, and the main core were suffering from overload, they hang on it very well, in order to stop the overload, one of the links to the ESX Chassis were disconnected from one of the 4900 switches. The CPU usage from the 4900 and the core(6509) went down below 40%, and then they started to migrate the virtual servers from the chassis to another 2 chassis that were added right after. They were actually working well, but suddenly the 6509 changed to the other supervisor after everything was OK. We were wondering what could have been the cause of this, maybe the virtual servers migrations, maybe the overload from the ESX ? We also had a few question, is there any need to reload the cores every few months as a planned task ? Because the cores have been up for more than 1 year. And also is there any kind of of tool to monitor the CPU status, or the status overall from the cores or the switches ?
View 3 Replies View RelatedCisco Switching/Routing :: 4506 - Upgrading Sup V To A Sup 7 Engine
Jan 4, 2013I am currently running a 4506 with a sup V engine. I have purchased a sup 7 engine. Is there a guide on how to perform this task. I am sure I need to do an IOS update as well.
View 2 Replies View Related