Cisco WAN :: Can IOS Be Installed On Catalyst 2901 Switch With Sup Engine
Jan 22, 2011I have Cisco Catalyst 2901 switch with Sup engine which have CatOS installed. I want to know that can I install Cisco IOS in this switch.
View 1 Replies
ADVERTISEMENT
Cisco WAN :: Command To View What Type Of SFP Module Installed In Catalyst 3750 Switch?
Jan 20, 2013Is there a command that can be used to view what type of SFP module that is installed in Catalyst 3750 switch?
View 6 Replies View RelatedCisco WAN :: Catalyst 4500 E-Series Supervisor Engine 7L-E?
Aug 12, 2012I have a strange issue with 4500 E chassis loaded with SUP 7L-E which always remains in ORANGE LED status, also the uplink ports interface is down and the line protocol is down but when i execute the command sh int gig1/5 it show me the media type sfp but there is no red laser light seen in the sfp transiever,The below command is configured for the uplink gig port on the SUP engine.hw-module uplink select gigabitethernet?
View 10 Replies View RelatedCisco Switching/Routing :: Catalyst 4006 Supervisor Engine Led Red
Nov 28, 2011we got a problem with our cat4006 coreswitch. The led on the supervisorengine is red, and several errors are appearing in the message log. [code]
View 1 Replies View RelatedCisco Infrastructure :: Supervisor Engine Catalyst 6500 Modular IOS?
Oct 11, 2011I want to know the difference between the software that is Modular and the one that is not. What are the pros and cons ?
CAT6000-SUP32 IOS ADVANCED IP SERVICES SSH or CAT6000-SUP32 IOS ADVANCED IP SERVICES SSH (MODULAR)
Cisco WAN :: Functionality Difference In Supervisor Engine 2 / 2T For Catalyst 6500?
Aug 10, 2012Is there functionality difference in Supervisor Engine 2 and Supervisor Engine 2T for Catalyst 6500 ?
View 3 Replies View RelatedCisco Switching/Routing :: Catalyst 6509-E / Replace Supervisor Engine 720 10GE
May 15, 2012we have Supervisor Engine 720 10GE (VS-S720-10G) in slot 5 on Catalyst 6509-E. Slot 6 is free. We need to replace VS-S720-10G. Is it possible the following scenario
1. we will insert new VS-S720-10G into the slot 6
2. then we will remove the faulty VS-S720-10G from the slot 5
Will everything work without interuptions. Is any document where I can find step-by-step procedure how to replace VS-S720-10G ?
Cisco Switching/Routing :: Catalyst 4500E Supervisor Engine 7-E / Possible To Deploy Simultaneously Both Type Of Ports
Aug 8, 2012We've got a doubt about the uplink ports of this supervisor. I've read that you have to use the four ports in 10G mode or in 1G mode, but not use for example 1 port in 10G mode and 1 port in 1G mode:
But, you can read in another sentence: " Beginning with Cisco IOS Release 12.2(25)SG, you could simultaneously deploy the dual 10-Gigabit.Ethernet ports and the four Gigabit Ethernet SFP ports on the Catalyst 4503, Catalyst 4506, and Catalyst 4507R chassis." Is it posible deploy simultaneously both type of ports?
Cisco Switching/Routing :: Secon SUP Engine On 4507R Switch?
Mar 8, 2012I need to add another SUP engine on Cat 4507R switch, with a new one. I have old SUP engine running in this switch. Sometime this switch is reloaded without any reason. So we want to add another sup engine for redundancy. What is the procedure to do this & also how much outage time would it cause? Which sup engine will be run as primary and which one should be redundancy?
SWITCH-4507#sh ver
Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9K91S-M), Version
12.2(25)EWA8, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 24-Jan-07 15:28 by pwade
[code]....
Cisco Switching/Routing :: Supervisor Engine For 4003 Switch
Oct 24, 2012I buy a Cisco 4003 Switch with Supervisor Engine I but it only run CatOs and i whant it to run Cisco IOS so whitch Supervisor Engine can the Cisco 4003 Switch run? i have look at the Supervisor Engine III it can run Cisco IOS and Layer 3 but can i use that in my Cisco 4003 switch?
View 14 Replies View RelatedCisco WAN :: P2P Fiber Utilizing 2901 ISR And 2924XL Switch
Jun 8, 2013I am having a bit of trouble with the following scenario; I have two 2901 ISRs and a 2924XL setup in the following fashion.
2924XL--->P2P-Fiber--->2901ISR--->P2P-Fiber--->2901ISR
I need to be able to reach the LAN 192.168.1.0 from 192.168.3.0 for TS but cannot get this to work. I can ping from within the switch all around and i can ping from within the woodlawn router all around but cannot ping host to host.
Cisco Switching/Routing :: 3750 Switch - SNMP Engine Attempted To Lock Semaphore
Aug 8, 2012I am having a lab switch. Recently I am getting "%SCHED-3-SEMLOCKED: SNMP ENGINE attempted to lock a semaphore, already locked by itself" message and the switch has started to hang a little bit. I just want to know what this log means and how to trouble shoot.
I'm using C3750, version 12.2(25)SEE3
Cisco WAN :: Need Data License To Switch Back To 3g 1941 And 2901 ISR Routers
Oct 2, 2012I have 1941, 2901 ISR routers. I will use 3G backup when primary link (metro ethernet / G.SHDSL) goes down. Do I have to use Data License (SL-19-DATA-K9 / SL-29-DATA-K9) in order to switch back to 3G when primary link is not reachable) ?
View 7 Replies View RelatedCisco Switching/Routing :: Catalyst 4006 / Quickly Copy Configuration From Production Switch To Spare Switch?
Nov 20, 2009I have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies View RelatedCisco :: Can Switch Detect Mac Address If Driver Is Not Installed
Feb 27, 2013I have asked this question in server fault but not getting good answer.Can Cisco switch detect mac address if driver is not installed?
View 7 Replies View RelatedCisco :: 2800 - Upload An IOS File To A Router Or Switch To Be Installed
Nov 1, 2011I want to download the iOS update to my Cisco 2800 Series Routers and Cisco Catalyst 2960 Series Switches and leave them there till im ready to install them. Is this possible?
View 1 Replies View RelatedInternet Drops / Recent Switch Installed To Setup?
Jul 23, 2011So I have a netgear wireless router that my computer uses to access internet, then i have ethernet cable running from that netgear into my room to a linksys befsr41 router that I disabled DHCP to use as a switch. I have the ethernet cable going into the 4th slot and my xbox going into the 1st. I got it working however...and before i say this let me tell you, before introducing the linksys as the switch everything was working fine, both wireless to my computer and wired into my xbox straight from the Netgear. Ok back to my issue, while watching netflix on my xbox every 10 minutes or so i will get disconnected from the network on both my computer [wireless to netgear] and xbox wired to netgear through linksys. I was wondering if this could maybe be some kind of IP Address issue.
View 13 Replies View RelatedCisco :: 2960S Catalyst Access Switch From VPN
Dec 10, 2012I have a 2960S Catalyst switch in my LAN, with the firewall and the servers in the same VLAN (vlan 3).All the servers and the firewall are in the vlan 3 are in the "192.168.19.0/24" subnet, the firewall has the IP "192.168.19.1".I can land on the firewall with a VPN (192.168.130.0/24) which has a complete view on the subnet 19/24.I can access, manage and get SNMP information of the Catalyst from the servers but I can't do the same from the VPN.Is there some feature I need to enable on the switch in order to allow 192.168.130.0/24 to access it?
View 4 Replies View RelatedCisco WAN :: Catalyst 2950 - Switch Configuration
Dec 27, 2010I just started configuring my cisco catalyst 2950 switch. Basically im preparing for my CCENT exams my basic configuration is as follows.
-My Laptop is connected to the console port
-I'm connected to the internet via my wireless
-I'm connected to the switch port via my NIC card
Cisco :: Catalyst 2960 Series 8 Port Switch?
Oct 18, 2012I'm trying to configure Catalyst 2960 series 8 port switch in my office. I have just plugged in switch and started and then put Ethernet cable (which is coming from the wall port (LAN) into CONSOLE (switch). and connected my laptop's ethernet cable to switch's 1x por
View 16 Replies View RelatedCisco Switching/Routing :: Can't SSH Into New Catalyst 2960 Switch
Jun 13, 2012I'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
Cisco LAN :: Catalyst 500 Express Switch / Discover Tool?
Jun 18, 2012is there a discover tool for such a switch, i forgot the assigned ip .
View 2 Replies View RelatedCisco WAN :: Catalyst 3550 Switch Routed Interface
Feb 21, 2011we are using the catalyst 3550 L3 for BGP routing. For e.g. Gi 0/4 is our internal interface tha we want "switch".
We need on Gi 0/5 the same network that is on gi 0/4.
How is it possible? Make it like a 2 port mini switch. Or make a bridge of these 2 interfaces without any complicated reconfiguration needed?
Cisco WAN :: Password Recovery On A Catalyst 3850 Switch
May 23, 2013I'm trying to do password recovery on a Catalyst 3850 switch..I've read the section in this: url...where it says that I need to have physical access to the switch (I do), and that I reset the password if I issue a break command and interrupt the boot procedure. I've tried to do that... it gives me the "switch:" prompt, so I think I've interrupted the boot procedure successfully, but, what do I do next?I've successfully done recoveries on Catalyst 2950s, 3550s & 3560s, but the procedure for this one, if I'm reading the link above right, sounds like it's completely different.
View 10 Replies View RelatedCisco Switching/Routing :: Catalyst 2960 Switch Qos
Aug 20, 2012i try to implement layer 2 qos in 2960. when i complete to configure the switch, i want to test the qos.PC1 conect to switch port 1,PC2 conect to switch port 2 . PC1 is source teminal. i use skydata.exe and FTP for the test.
when use the skydata ,the PC2 speed can reach 10mbps.when use the FTP , the PC2 only can reach 1.2mbps. why?
Cisco WAN :: No IOS - Cannot Access Multilayer Switch (catalyst 3750)
Sep 10, 2011Working on my CCNA w/ live equip, I accidentley deleted the hardware IOS- yes, beginners mistake. Upon bootup, I do not get a command prompt. I tried the recovery procedure(hold mode button before power up) recommended by Cisco to no avail. My issue is I use SecureCRT & the charaters/font is ineligible. Here is an example of what I see when typing; "þæb Bûÿÿûýÿ¿¿ÿÿ". Currently, the SYST indicator is blinking & I have no access.
View 3 Replies View RelatedCisco Switching/Routing :: Can't SSH Into New Catalyst 2960-S Switch
Apr 29, 2012I can use Putty to SSH into my new switch (Directly connected to my laptop with ethernet cable), but I cant log into my switch.
Sent username "admin"
admin@192.168.251.1's password:
Access denied
It doesnt like my password, but I have only set 1 password (king) on this switch. I've configured 3 other switches with SSH and had no problem. Been trouble shooting for awhile and It'd be great if I could have a 2nd set of eyes take a peek, Also, my running config is attached.
Cisco :: Memory Utilization OID For Catalyst 6506 Switch
Dec 26, 2012We have one Catalyst 6506 ( with WS-SUP720-3B, IOS is 12.2(18)SXF14 ) and one Catalyst 6509 ( with WS-SUP720-3B, IOS is 12.2(18)SXF17a ). We used WhatsUP to collect I/O & process memory utilization for both switches. The memory utilization for Catalyst 6509 was ok, but it seems not correct for Catalyst 6506 ( show proc memory displayed the total memory is 512MB, but the WhatsUP displayed only 64MB only )
View 1 Replies View RelatedCisco WAN :: Catalyst 3750 - Adding Switch To Stack
Mar 23, 2012I have a Catalyst 3750 I want to add to an existing stack (same models) through the stackwise port We use some complex QoS and other features on our network, and I'm not sure how much configuration I need to do on the new switch before adding it to the stack. Since this is going into an existing setup?
View 9 Replies View RelatedCisco WAN :: Connect 2960-S To 3560 Catalyst Switch?
Feb 22, 2012Im trying to Connect a 2960-S Catalyst Switch to a 3560 Catalyst Switch. It worth pointing out im newish to switching although i know some commands and what they do This is my first time connecting 2 switches together.They are connected via a crossover cable and have green lights flashing on the connected ports When i run "show CDP neighbours it sees the new switch Unable to ping new switch...just timesout Here is the the interface on the 3650
GigabitEthernet0/40 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 001b.532f.8428 (bia 001b.532f.8428)
Description: Uplink to Switch 2
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
[code]....
Cisco Switching/Routing :: Catalyst 2948G Switch Got Dead
Feb 15, 2012I had an old Cisco Catalyst 2948G switch that I have not used in about 7 years down in my basement. I powered it on and went through the process of clearing out the configurations, and I got to a point where one of the commands to clear out the config asked me to install jumpers for "ROM" and "ERASE". There is a third jumper labeled "NO BOOT". They are numbered J6, J7, & J8 respectivelyI found the jumpers inside and put the jumpers on them and ran the command expecting it to remove any old configurations I had on the switch and bring it back to factory state, but I was wrong.
View 3 Replies View RelatedCisco Switching/Routing :: PA-MC-2E1 / 120 Work With Catalyst Switch 6506E?
Dec 12, 2012Does the port adaptor PA-MC-2E1/120 work with the Catalyst Switch 6506E (Sup Engine: 720-3B)? We have bought a Enhanced FlexWAN card for this port adaptor.I read through the cisco website and seem to get confusing answers whether they are compatible.
View 1 Replies View RelatedCisco WAN :: Connecting WAP4410N With 2 SSIDs To Catalyst 2960-s Switch
Apr 21, 2012I added Linksys RV-016 16-ports VPN Router into the connection. RV-016 supported multiple subnets.
As mentioned in [URL], D-Link DIR-615 needs to be a device which could support multiple Vlan subnets. But unluckily DIR-615 does not support multiple Vlan subnets.
Therefore I added Linksys RV-016 in the the combination of devices. As what i found in RV-016 GUI setting, it supports multiple subnets.
Purpose outline:
1. Have to create two different SSIDs.
- SSID 1 for Management (able to view all other LAN devices)
- SSID 2 for guest and staff (unable to view all other LAN devices)
2. Create two VLANs in catalyst 2960s.
3. Create two subnets in Linksys RV-016 to accept two Vlans from catalyst 2960s.
Any experience of configuring RV-016 for the mentioned purpose above?