I want to download the iOS update to my Cisco 2800 Series Routers and Cisco Catalyst 2960 Series Switches and leave them there till im ready to install them. Is this possible?
View 1 RepliesI have an odd problem with the FTP server. I currently hooked up a 250GB portable HDD which is formatted in NTFS. A single folder in the root of the drive is mounted as the FTP server. Every time I upload a zip or far, the file comes out ends up being uploaded corrupt and double the original file size. I have used 2 FTP clients, using either ASCII or binary. No matter how I go about it, I can't make the files upload at the normal file size. Its not just archives, however, I tried an mp3 and it too got uploaded corrupt and double the size. I then downloaded the mp3 to try and play it but it didn't play in windows media player. However I loaded the 'corrupt mp3 into audacity and the file played like normal.
View 5 Replies View RelatedI was uploading a big 2gb file to my FTP server, it was all going good and I managed to upload the whole thing hassle free. After I finish I log out, and return about 3 hours later and try to log back in, to no avail.WinSCP gives me the following error:
[code]....
I am using WiSM in 6509, this WiSM has two controller with the same management IP subnet, I tired to upload the configuration to the TFTP server, but tried many times, one of the controller working well, but the other one always cannot reach the TFTP server, here is the debugger log for both controller
Failed one:
(KGV-WiSM-1) >debug transfer all a enable
(KGV-WiSM-1) >*TransferTask: Nov 10 16:26:08.735: RESULT_STRING: TFTP Config transfer starting.
*TransferTask: Nov 10 16:26:08.735: RESULT_CODE:1
*TransferTask: Nov 10 16:26:32.018: Locking tftp semaphore, pHost=172.16.102.107 pFilename=/KGV.aes
*TransferTask: Nov 10 16:26:32.018: Semaphore locked, now unlocking, pHost=172.16.102.107 pFilename=/KGV.aes
[code].....
why the controller can't upload the file, I can ping both controller and both controllers can ping to the TFTP server.
I can't upload on file-sharing sites , I have tried to upload on wupload.com , fileserve.com , ****file.com and other sites and I click to upload but the progress don't start only stay in 0% I have waited 3 hours to upload a music with 150 MB and still in 0% progress .
View 5 Replies View Relatedare there any free services where you can remote upload a file (zip file 25MB) and have it sent to me via email as an attachment. not a link where i have to download the file.
View 1 Replies View RelatedI have a router Cisco 2800, but always is in Rommon, the message show is:
device does not contain a valid file system
dir: cannot open device "bootflash:"
rommon 8 > dir usbflash0:
Checksum failed on c1840-usbfslib-m
Expected checksum: 91d6, calculated checksum: 4527
open: file "c1840-usbfslib-m" not found
open(): Open Error = -1
loadprog: error - on file open
cannot load the monitor library "bootflash:%c1840-usbfslib-m"
from device: usbflash0dir: cannot open device "usbflash0:"
I want upgrade my switches 2960-24PC-L RAM: 128MB and Flash: 28MB, but in the web page of cisco I see that the requirement of hardware is RAM: 128MB and Flash: 32MB.
I download the IOS file and this file is only 11.2MB so my question is if I can upgrade the IOS because my flash is enough for upload the IOS file.
I wan to migrate from a router 2800 to L3 switch 3750G , the thing is that we have several vlans and we use a router sometimes with each interface configure with correspoinding vlan subnet ip to route traffic between vlans there is no static or dynamic routing only directly connected interfaces on router routing traffic to each other ?How would i configure a L3 switch interface for simillar functionality , below is my current router configuration
!
ip domain name yourdomain.com
multilink bundle-name authenticated
!
vtp mode transparent
[code]...
is it possible to upload a htm file to the router using a command prompt? the page is located at [URL] I want to change the option of Allow All to Restrict Access at 8pm every night?
View 3 Replies View RelatedIf i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies View Relatedhow can i upload IOS in Switch when it is in ROMMAN Mode , its show IOS in flash but may pe Corrupt, show how can i put New ios in Switch 3560.
View 1 Replies View RelatedI have a router connected ea2700 on the Internet port to a switch se2800.e switch is connected and everything is gigabit nas. if I try to transfer a file from PC, gigabit ethernet, the transfer rate does not exceed 8 MB/s. if I transfer a file from the NAS to the PC speed is 15 MB/s. the support advised me to change MTU manufacturer parameters,to disable protection,and clone the mac address.the situation has not changed.if I configure the router in bridge mode, the speed is 22MB/s and 45MB/s.
View 3 Replies View RelatedI have asked this question in server fault but not getting good answer.Can Cisco switch detect mac address if driver is not installed?
View 7 Replies View RelatedI have Cisco Catalyst 2901 switch with Sup engine which have CatOS installed. I want to know that can I install Cisco IOS in this switch.
View 1 Replies View RelatedI have windows server 2008r2 running a FTP server, so I can back up my configs and upgrade IOS when needed. My problem is than I can backup to the server just fine but when i try and restore a config or pull a new IOS over it gives me this error
%Error opening ftp://13****** (Protocol error) this is happening on every switch I have and I can't figure it out.
So I have a netgear wireless router that my computer uses to access internet, then i have ethernet cable running from that netgear into my room to a linksys befsr41 router that I disabled DHCP to use as a switch. I have the ethernet cable going into the 4th slot and my xbox going into the 1st. I got it working however...and before i say this let me tell you, before introducing the linksys as the switch everything was working fine, both wireless to my computer and wired into my xbox straight from the Netgear. Ok back to my issue, while watching netflix on my xbox every 10 minutes or so i will get disconnected from the network on both my computer [wireless to netgear] and xbox wired to netgear through linksys. I was wondering if this could maybe be some kind of IP Address issue.
View 13 Replies View RelatedIs there a command that can be used to view what type of SFP module that is installed in Catalyst 3750 switch?
View 6 Replies View RelatedSo what i want to know is, is it possible to file share only using a switch? At the moment I have 5 xp 1 switch (with ethernet cables) No router and no internet (the no internet can not be changed).
Will i have to set up individual ips manually (192.168.1.1/2/3/4 etc and then create a home network using the wizard and create a network disk.
Or save our time and get a router
i can't find languages file for series 200 switch...where are?
View 1 Replies View RelatedAt home I have a perfectly working test setup for more than 1 year now , but yesterday we had a power down for about 10 minutes in the whole area , after this power down nothing was working in my network any longer.
My Network is has follow :
ISP(Cable Modem) on FA23 from the CISCO 2950 SWITCH (24 Ports)
ROUTER (ON A STICK) on FA24 from the CISCO 2950 SWITCH
And the rest of the switch is FA1=VLAN 1; FA2=VLAN 2;FA10=VLAN 10
Our home network is connected to VLAN 10 with a IP Range of 192.168.10.x /24 After this power down , I was not able to look into the SWITCH via FA1 , the FIX IP in this switch was 192.168.1.251/24, the ONLY way to get access was via the consol port !!!What a suprice when I connected my consol to the PC , I can see ROUTER_F342 , my router config is called ROUTER1841 and my switch config name is /was called SW24.So it seems that after this Power Down , the router took or received a config from my provider ?!?
I have recovered the the file in the switch + the vlan.dat and now everithing works again.
How can I avoid that this switch receive again a wrong file , I have all the needed files on the products itself and I do not use a TFTP server.
I have atached some screen shot when my switch is starting up , and it seems that the switch receive a IP address from my ISP , I do not know why, in the config file I have given it a FIX IP 192.168.1.251/24 ?!?So it seems that my ISP erase the config file and when the switch is empty ,the swich look for :
tftp://255.255.255.255/router-confg
tftp://255.255.255.255/ciscortr.cfg
Etc ....
Until it find something.
I have tried after a complete recovery to switch off the power again for 10 minutes (ISP MODEM + SWITCH + ROUTER) and I was not able to reproduce the fault.Can it be that due to this power failure in our area that some routers or switches send or broadcast this kind of things ?
what is location of flash file in 6500 Series switch and how can we take back of IOS image for 6500 series.
View 4 Replies View RelatedI have a 3560x switch with the flash formatted . I have tried to solve the problem by copying the IOS file to the flash. But the boot failed either .I have tried to copy the same IOS by the Xmodem, The boot failed again.My question is how to fixed the boot issues after the flash was formatted?
View 4 Replies View RelatedI uploaded a new config file via TFTP to a 3560 switch. What are the order of commands to get it to boot from this new config file instead of the file listed in 'sh boot': [code]
View 7 Replies View RelatedI just upgraded my cable modem from the Motorola Sufboard 5120 to the DOCSIS 3.0 capable 6120. Provisioned it with Comcast and their "Blast" service (supposedly it caps at 16 down, 2 up).
I had, in the past, used my desktop via N-format wireless (DWA-525 N-format PCI adapter and DIR-655 N-format router) to do a speedtest.net test. I was getting 16 down and 2 up (as advertised). When I switched to the 6120, I did a speedtest.net test again to see what kind of gains, if any, I was getting. Turns out, I was getting 20+ down (nice improvement) and 1/2 Mbps up (a fourth of what I used to be getting?). Called Comcast. They "sent signals" (don't they always?) and claimed that it fixed it. My download speeds increased a smidge (about 22), but my upload speeds were still .5. Called Motorola, they had me do a few things and now I get 1 Mbps up and 27 - 30 down via wireless.
My download speeds are great. I'm content with that. If I hardwire from the cable modem directly to a ****py old laptop, a speedtest.net shows 4 Mbps up. So why do I get such a high upload speed when hardwired (4 Mbps), but a fraction of it (1/4th) when wireless? I'm not using any other devices to sap bandwidth (some are connected -- i.e. another desktop, my Droid phone, etc., but aren't actively pulling packets). And why would it go from 2 up (on my desktop via wireless in the past) to only 1 up (via wireless now) when the setup is the same across the board (as best I recall) other than upgrading my cable modem.
Since I get 4 up when hardwired straight off the cable modem, I assume my DIR-655 is slowing me down somehow. How to pick up the pace a bit? I've already tried the standard "power cycling", etc.
Oh, and the reason I go wireless -- my cable modem and wireless router are in my game room in the basement for my PS3. My desktop computer (and the wife's desktop computer) are two floors directly above it in our "office". Signal strength is "excellent" ... always has been. And again, pretty much everything is the same.
[URL]
I have the attached setup. now i would like to limit my ftp transfer to 10 mb from a specific vlan to ftp server on the STM-4 (622) link. what would be the best way to limit ftp traffic to 10 mb .Video_Main#sh verCisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)Technical Support:
[URL] Copyright (c) 1986-2011 by Cisco Systems, Inc.Compiled Tue 26-Apr-11 18:09 by prod_rel_team
Image text-base: 0x100A0994, data-base: 0x13CAB728
ROM: 15.0(1r)SG1Jawa Revision 7, Snowtrooper Revision 0x0.0x116
Video_Main uptime is 15 weeks, 3 days, 23 hours, 53 minutesSystem returned to ROM by power-onSystem restarted at 16:38:21 UTC Wed Nov 23 2011Running default software
License Information for 'WS-X45-SUP7-E' License Level: entservices Type: Permanent Next reboot license Level: entservices
cisco WS-C4506-E (MPC8572) processor (revision 8) with 2097152K/20480K bytes of memory.Processor board ID FOX1502GZHFMPC8572 CPU at 1.5GHz, Supervisor 7Last reset from PowerUp9 Virtual Ethernet interfaces204 Gigabit Ethernet interfaces10 Ten Gigabit Ethernet interfaces511K bytes of non-volatile configuration memory.
Configuration register is 0x2101
Video_Main#
I am getting very slow window file transfer speed (4 Mbps per second) between two connecting servers in Cisco 6509 switch. I have connect the two laptops in 6509 switch in same module using the same vlan and try to copy the files from one laptop to another and vice versa and got the same speed on 4 to 5 Mbps per second. Switch utilization is not more than 10% and both the laptops are connected in 1 Gbps full duplex.
I have checked by removing the gateway in both laptop but the output is same.
i hace a VPN configured between two Cisco ASAs, but I have a problem to reach a network behind a router 2800.
View 7 Replies View Relatedwant to ask something about configuration ruter 2800I already have a usb to DB9 | DB9 to RJ45but i have a problem like the image below
View 19 Replies View RelatedHow to add a wic-2t card on router 2800
Had the card as follows
I want to know routr 2880, such as the following picture
I am operating a 2800 series Cisco router. The router is working fine except that I am not able to SSH into the router. I have checked the running config with cisco's documentation and every line is correct. Prior to me getting this job they did an update and think they have corrupted the a certificate key for SSH.
Any command to generate just the SSH key and not all the other keys that would cause bigger connection issues.
I have 2 2800 series routers configured the same, but with different subnets. One works fine, the other the client can't obtain an IP, and hardcoded, cant ping.
I ran DHCP debug and I can see the router assigning the IP, and I see and ARP entry that matches the MAC of the client.
*Feb 24 11:33:55.915: DHCPD: Sending notification of DISCOVER:
*Feb 24 11:33:55.915: DHCPD: htype 1 chaddr 000a.e40c.d232
*Feb 24 11:33:55.915: DHCPD: remote id 020a0000ac10760101000078
[Code].....
find the firmware file for 2800 series router? I need to upgrade the firmware to this router to get adsl annex M mode to work.
View 1 Replies View Related