Cisco Switching/Routing :: Slow File Transfer Speed In Same Vlan Of 6509 Switch
Mar 16, 2013
I am getting very slow window file transfer speed (4 Mbps per second) between two connecting servers in Cisco 6509 switch. I have connect the two laptops in 6509 switch in same module using the same vlan and try to copy the files from one laptop to another and vice versa and got the same speed on 4 to 5 Mbps per second. Switch utilization is not more than 10% and both the laptops are connected in 1 Gbps full duplex.
I have checked by removing the gateway in both laptop but the output is same.
View 7 Replies
ADVERTISEMENT
May 29, 2012
I am doing image upgrade on Catalyst 6509-E. During TFTP image transfer to sup-bootflash I always see !!!!!!!!!!!!!!!!!o!!!!!!!!!! "o" out of sequence packet. Although the image size seems to be correct at the end but there is always some "o" packets.
I am assuming not, but I haven't tried loading with the image after seeing this.
View 2 Replies
View Related
Mar 3, 2011
I have two machines that both have WUSB600N wireless network adaptors with a Cisco WRT160N router. The file transfer speeds between the two devices maxes out at 1.6Mbs. If I run speed tests off the internet I hit 15 to 20 and downloads are excellent. I have played with all kinds of settings for the driver and router but nothing seems to work. Both these devices are running Windows 7. I tried a file transfer with an XP device as well and it maxes at about 1.6. how to increase the bandwidth??
View 1 Replies
View Related
Mar 24, 2012
I have recently purchased a Cisco E4200 to replace my D-LINK DIR-655, which I thought was defective because I was getting slow wirless file transfer speed, regardless of setting, location and client.Using the E4200, when I transfer a file from a PC to another, both connected at 300mb on the 2.4ghz band, the file transfer rate reported by windows 7 and networx is from 2MB/s to 3.5MB/s. I think those transfer rates are not acceptable. Is that a good assumption ? I would expect something in the range of 10MB/s (which is what I get with a cheap dlink router, wired)
I also had great difficulty finding a channel. I had to try them all one-by-one as the auto channel selection made my PCs connect at 130mb.The E4200 is setup as follows:
-WPA-Personal
-Channel 5
-802.11n only
I have tried 3 different computers with different network adapters and they all underperform (IMO..).There are no other wireless networks in my area.I also took the E4200 to my office which is very crowed. Every single channel is occupied by several wireless networks. I get a file transfer speed PC to PC of about 2MB.I basically could have kept my DIR-655 as the speeds are identical.
View 4 Replies
View Related
Oct 31, 2012
I have the attached setup. now i would like to limit my ftp transfer to 10 mb from a specific vlan to ftp server on the STM-4 (622) link. what would be the best way to limit ftp traffic to 10 mb .Video_Main#sh verCisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)Technical Support:
[URL] Copyright (c) 1986-2011 by Cisco Systems, Inc.Compiled Tue 26-Apr-11 18:09 by prod_rel_team
Image text-base: 0x100A0994, data-base: 0x13CAB728
ROM: 15.0(1r)SG1Jawa Revision 7, Snowtrooper Revision 0x0.0x116
Video_Main uptime is 15 weeks, 3 days, 23 hours, 53 minutesSystem returned to ROM by power-onSystem restarted at 16:38:21 UTC Wed Nov 23 2011Running default software
License Information for 'WS-X45-SUP7-E' License Level: entservices Type: Permanent Next reboot license Level: entservices
cisco WS-C4506-E (MPC8572) processor (revision 8) with 2097152K/20480K bytes of memory.Processor board ID FOX1502GZHFMPC8572 CPU at 1.5GHz, Supervisor 7Last reset from PowerUp9 Virtual Ethernet interfaces204 Gigabit Ethernet interfaces10 Ten Gigabit Ethernet interfaces511K bytes of non-volatile configuration memory.
Configuration register is 0x2101
Video_Main#
View 6 Replies
View Related
Sep 17, 2012
I have a Cisco 6509 with IOS "s222-ipservicesk9_wan-mz.122-18.SXF16.bin"I need to enable dot1x on user's ports on the switch. each user is connected to the switch through the IP phone.
I just found out that I can not enabled dot1x on trunk port. I have tried to use "switchport voice vlan " but I got:
Switch(config-if)#switchport voice vlan 123
Command rejected: Gi7/20 is Dot1x enabled port.
let me know what should I do to get dot1x working?
Note: I have connected a laptop directly to the port and dot1x is working fine.
View 5 Replies
View Related
Jun 2, 2012
I am transferring music files from an External HDD link by USB to my laptop to a Synology 410J NAS, I have both a wired and a wireless connection. The NAS is connected to a 2wire modem and router, and so is the laptop. I am getting speeds of between 450KB to 600KB a second i.e. 0.45 to 0.6MB per second. How can I make this faster?
View 1 Replies
View Related
Sep 13, 2011
I spoke with two different support agents with a well respected routermanufacturer. I got two different answers - No surprise.So, I ask the forum, what file transfer speeds should I expect when transfering a good sized amount of data (10gig) from wired PC on a 10/100/1000 network router to another PC via wireless connection 20 (feet away + two walls) using 802.11N.Both PC's are new / newer with win 7 64 bit. - Current transfer speeds - Both wired and wireless internet download speed tests are arond 21 meg per second. Both PC's wired and wireless get around 3.7 meg per second internet download (speed tests).At this point - no real difference in internet access between PC's and wired / wireless.
However, when I copy a file from PC1 to PC 2 (both wired) I get 68 megs per second. When I transfer the same data set (10 gig) from PC1 wired to PC 2 wireless, the data transfer falls to 3.7 meg per second. One rep told me to expect about 80% of my wired rate or about 54 megs per second (when using my 802.11N 300meg) equipment. The other rep (same company) told me that the 3.7 meg per second ia about the best I can expect. A transfer rate of 3.7 megs per second simply does not appear to be a reasonable speed given that all my wireless equipment is pretty new and supports numbers that are much higher
View 1 Replies
View Related
Dec 30, 2012
Installed brand new CAT6 cable from my office PC (W7) to my HTPC (W7) to stream movies (150 feet) and I cannot get file transfer speeds higher than 1MBps. I get the sames slow speeds whether I use the router or plug the two PCs together.
View 12 Replies
View Related
Feb 13, 2011
url...I have 2 PC's connected to a DIR-615 through 802.11n and each have a DWA-130 802.11n adapter. I am running Windows 7 Ultimate 64 bit on both computers. The specs of both systems are very high.I only have these 2 computers on wireless right now. Their signal is full strength, they are less than 10 feet away from the router.I am getting 2.0 MB/s when transferring files between them and although I am not expecting to get 17MB/s, but I should be getting better speed than 2 MB/s.Hard drive specs are Crucial C300 SATA 6.0, WD Caviar Blue SATA 3.0, and WD Caviar Green SATA 3.0. My Green drive reads/writes at 100MB/s, My Blue 125MB/s, and My SSD 225MB/s. So, those are not the bottleneck.Is there any other settings I can try? I have not messed with my DWA-130 settings nor have I messed with Windows.
View 7 Replies
View Related
Apr 22, 2012
I have a wireless network with 2 desktop hooked up wired, and one laptop that's wireless. Accessing files on the desktop with xp installed is quick and transfers files at around 5-7mb/s. When I connect to my main pc with windows 7 on it, file transfer is EXTREMELY slow and almost always stutters and freezes. I've tried removing the drive from 'shared' and then adding it again, reinstalling my ethernet driver, swapping ethernet ports on the back of my router, and resetting it altogether. Still a slow transfer speed.I use workgroup all around, for xp and for 7.
View 3 Replies
View Related
Mar 12, 2011
Just relised this problem after trying to leech some stuff from a friend from his pc at a lan My connection seems to go REALLLY slow. Heres a pic nobody else is file copying and its the same from every pc.
View 7 Replies
View Related
Apr 7, 2011
i am running windows server 2008 with the hyper V role installed.i have installed windows 7 Professional as a guest OS. assigned 2 GB of Ram to the machine. the point behind the VM is to virtualize my FTP server and incase a format is required i have the VM file on my 2nd partition, host OS on another. i use Cerberus FTP Server on the Win7 OS. i configured the server to accept SFTP and TLS connections. on the host OS i installed Fire FTP and File Zilla, both Clients will at max download a 4 MB file at 64 KB/Sec .. i have seen both jump to about 80 KB but was only a split second and never held.. however if i login without SFTP and transfer over standard protocol, i download at 1 MB/sec. which is my normal speeds. would this be only to the encryption process?, in the Cerberus Server there are options to adjust download speeds, i have left it default, and altered it to allow its max configuration. My ISP is not limiting any connections that shouldnt be.
View 1 Replies
View Related
Nov 7, 2011
I am having incredibly slow connection while transferring files using file sharing.I have the below hardware:
108Mbps TPLINK Wireless Router
TL-WR642G 108Mbps TPLINK Wireless Access Point acting as repeater
Laptops accessing internet and folder sharing enabled for local file transfer
Transfering of files excessively slow (after playing around with the settings was able to get 500KBps). I have set all wireless adapters on the laptops to 802.11g only.Tried setting the router and access point to both 54Mbps and 108Mbps 802.11G only as well as b/g.
View 1 Replies
View Related
Jun 27, 2011
I recently switched from an older 10/100 linksys to this gigabit router from D-Link. However, when I try to transfer files from one computer to another on the LAN, the file transfers are ridiculously low, right around 16KB/s. I have CAT6 cable for all connections, but am baffled by what could cause such a slow speed. I'm trying to transfer files from my desktop (win7) to my server (Windows Home Server 2011).
View 3 Replies
View Related
May 7, 2012
How can i connect my PC with laptop with LAN cable for high speed file transfer?
View 2 Replies
View Related
May 6, 2012
My XBOX started complaining when I began using Windows Media Center to stream videos from my PC to my XBOX. I found out that I had a wireless G router provided by verizon which wasn't fast enough to stream videos. SO, I went out and purchased a 4500EA router expecting it to be the fastest thing I had ever seen.
Now it seems a bit slow when trying to stream video from my laptop to the XBOX and i'm a tad bit confused as to why. So I did a file transfer from a desktop wired directly to the router from a laptop in the same room wirelessly connected to the network and my speed is about 4mbps. 4MBPS!? This device is supposed to be capable of moving packets LAN side at 450MBPS.
Both of my PC's are quad core, newer model PCs. I've tried moving files now for several hours with the same results. I've toyed around with my wireless adapters, changed power settings, full duplex, half, changed mtu sizes, changed security settings. I'm out of ideas.
Is getting about 1% of the advertised bandwidth normal?
View 2 Replies
View Related
Feb 23, 2012
1 newer build computer connected to D-link 655 via Cat6.1 laptop computer connected to same D-link 655 via Wireless N minicard. (Intel) (130Mbps connected) Router on a 10 foot shelf, always have full bar in wireless strength on 2nd computer.
Both computers can upload and download as expected from the internet. Transfers between the two computers though are slow. Both computers are loaded with Windows 7. Transferring files to or from the laptop transfers at 1.5MB/sec to 2 MB/sec.
View 1 Replies
View Related
Jul 23, 2012
I have a RV220W operating in 2.4GHz N-only mode. Channel bandwidth is set to 20MHz, channel to 6 (a site survey shows that channel as completely clear), WPA2/AES. I am connected to a TrendNet wireless bridge. The admin page for that wireless bridge shows a link quality of 100% with a signal strength of 71%. If I select a higher channel (11), the signal strength drops to 51%.
I have a Windows 7 PC connected to the Trendnet bridge and a Windows 7 server connected to the RV220W, both via a 1Gbps LAN port. When I transfer a file from the server to the PC or vice versa, I get a lowsy 2MBps (~20Mbps) transfer rate. That seems awfully slow. I tried channel bonding from 20 to 40 MHz
View 2 Replies
View Related
Feb 10, 2011
just bought a WD my book world edition 2 NAS and have been trying to tranfer files wirelessly to it but a 700mb file is taking 25mins to trans. my book is connected by ethernet to netgear dgnd3300 router and my laptop has sitecom 300n usb doongle.is there some sort of setting i've missed or is this speed normal?
View 5 Replies
View Related
Dec 25, 2011
I am using a DIR 825 and I experience slow data transfer speed within my internal network under the wireless connection (2.4 Ghz), 2 Mbs. I can videostream from the internet OK, no problems there, but when I want to transfer data between two external HDD (NAS devices) it can get as slow as 2 Mbs.
View 1 Replies
View Related
Jan 22, 2012
Transfering from PC to Laptop. This just seems slow. I'm wired to the PC and wireless to the laptop. With a A3 on 1.21 FW
View 4 Replies
View Related
Jan 31, 2013
I currently had 6 WAP321 setup in our work environment on 2 floor building as Single Point Setup cluster. When I do a 470MB ISO files transfer between the server and the laptop, the speed is very slow, rate at 130KBs and sometime it go up to 30Mbps.Is there anyway to tweek teh WAP to get FULL speed of wireless all the time?
View 5 Replies
View Related
Apr 14, 2013
Setup: SA540 (fw 2.1.71) with pretty basic configuration, no VLANs or QoS. Wireless APs and 3 large Netgear gigabit switches plugged straight into the SA540 LAN ports. Wireless APs are: 1 Aiport Express, 1 Linksys WRT54GL, and 1 Asus RT-N56U.
Problem: network speeds (transferring files) to the servers from wired and wireless workstations is very slow, around 200kBps.
Resoultion: plug the wireless APs into the Netgear switches instead.
Notes: any connection through each of the wireless APs was very slow, but not a signal problem. Even when plugging straight into one of the wireless AP's inbuilt switches, the speed is slow. Only when unplugging these APs from the SA540, and plugging the APs into any of the Netgear switches, does the transfer speed go back to normal even when the traffic still goes through the SA540 to reach the destination.
I don't understand why creating this extra hop between switches would be useful, and why plugging the APs directly into the SA540 is an issue.
View 1 Replies
View Related
Dec 4, 2011
I recently bought a new TP-Link TL-WR741N, I'm transferring data from my desktop wired network, windows 7 to net book windows xp wireless. i'm getting only 2 mbps.
View 3 Replies
View Related
Nov 26, 2009
I have the above router, but I have noticed that the USB Transfer speed is very poor. I have a WD External HD plugged into the router and id i transfer filed from my server which is hardwired to the router I only get a transfer speed of about 2.5MB/s.
For a USB device I was kind of thinking I would be getting a minumm of atleast 50-60MB/s.
View 9 Replies
View Related
Apr 3, 2013
In the process of upgrading the image for all of our floor switches..In total there are 35 WS-3560G-PS switches.
So far I have been upgrading them all to image c3560-ipbasek9-mz.150-2.SE2.bin and that has gone well.
But this eve 2 of the switches are extremely slow on the TFTP transfer. Duplexing and links are good back to core.
But when I do a sh ver to compare one switch that is good and one that isnt I noticed this
TFTP Transfer is good on this one - cisco WS-C3560G-48PS (PowerPC405) processor (revision F0) with 122880K/8184K bytes of memory.
TFTP Transfer is slow on this one - cisco WS-C3560G-48PS (PowerPC405) processor (revision F0) with 131072K bytes of memory.
View 2 Replies
View Related
Jun 29, 2011
My transfer speed from HDD which connected to linksys e4200 reach max 2,3MB/s how it is possible to watch fullHD movie if its required minimum 5MB/s? Maybe I should make some adjustments? HDD-WD My Passport 750Gb Also connection speed max reach 144mb/s?? how to make 300mb/s ? wifi adapter is Intel advanced N + WiMax 6250 AGN last driver installed, also E4200 last firmware installed 1.0.0.2 all settings by default Max download speed 75Mb/s by utorrent but provider gives 100Mb/s By cable its ok, max speed 100Mb/s as giving provider
View 9 Replies
View Related
Jun 11, 2012
I have an issue that I am trying to track down. When I have 2 servers on the same VLAN on my AS pair, all is good because nothing leaves the switch. Where the issue is, is when I have 2 servers on different VLAN's and it requires a hop across the Core router pair. This hop drops the throughput rate by about 20-25% (from 44M to 35-36M)I think I know the issue, but want some input to from other to make sure I am not off-base. I have a pair of 6509E chassis' running Sup720 (VS-S720-10G) with CEF720 (X6748-GE-TX) modules. This is my Access Pair running VSS to look as 1 switch.
These tie into the Core pair of 6500E chassis' running Sup720 (Sup720-3B). This issue I see is that the core has a CEF720 card (6724-SFP), but the AS pair does not connect to the core on that card, they connect on a RJ45 Ethermodule (6148A-GE-TX) card. Would the fact that the AS pair does not connect to the core on the CEF7220 module on the core, cause the traffic to not make use of the CEF features of the Core and make each packet then have to be processed by the core instead of Express Forwarded?
View 1 Replies
View Related
Nov 20, 2011
i have a newly formatted (i.e. empty) 2TB WD my book elite which when i connect it to my computers usb port, can transfer a 6gb video file at over 100MB/s according to the win 7 detail box. However, when i connect it to the usb port on the back of the e4200 and try to transfer the same file, it only goes at 8MB/s max ... it appears to be going at usb 1 speed. i've got the latest firmware on both the e4200 and the my book 1111 and everything seems to be working fine for both, except this transfer rate when connected to the e4200.granted, cisco doesn't specifically list this drive as being tested, but the router does recognize it and shows it as usb 2.0, but yet the transfer speed is just too slow.8MB/s is just not workable...i could just connect the drive directly to the computer and share it that way, but connecting it to the e4200 was one of the reasons i bought the e4200.
View 8 Replies
View Related
Jul 3, 2012
Transfer speed for sending or receiving files from a USB external HDD connected to the router is slow? Speed ranging from 2MB - 4MB/s. The HDD is definitely capable of at least 80MB/s if plugged directly into the PC. Is it meant to be this slow or there's a fix somewhere which I'm not aware of? Thought it's suppose to be the top of the line products but seems so inferior if I were to compare with other high end routers in the market which performs better, faster and definitely much cheaper.
View 9 Replies
View Related
Feb 5, 2013
We backup the running config on the 6509 does it also backup the vlan.dat as well?I tried command dir/all and just dir but did not see the vlan.dat listed
View 6 Replies
View Related
Nov 1, 2011
I have a Cisco 6509 connected (gig3/17) to a Cisco 3560 G switch (Gig 0/28). The 3560 switch Gig 0/26)is connected to a distribution switch on another network. The ip address on my 6500 is 10.120.11.244 255.255.252.0 and the ip address on my 3560 is 10.120.11.211. The ip address given to me by the other network is 10.162.20.10 255.255.255.252. How do I configure the new vlan in this situation and the ip address given to me.
View 4 Replies
View Related
