Just relised this problem after trying to leech some stuff from a friend from his pc at a lan My connection seems to go REALLLY slow. Heres a pic nobody else is file copying and its the same from every pc.
View 7 RepliesI recently switched from an older 10/100 linksys to this gigabit router from D-Link. However, when I try to transfer files from one computer to another on the LAN, the file transfers are ridiculously low, right around 16KB/s. I have CAT6 cable for all connections, but am baffled by what could cause such a slow speed. I'm trying to transfer files from my desktop (win7) to my server (Windows Home Server 2011).
View 3 Replies View RelatedI have a wireless network with 2 desktop hooked up wired, and one laptop that's wireless. Accessing files on the desktop with xp installed is quick and transfers files at around 5-7mb/s. When I connect to my main pc with windows 7 on it, file transfer is EXTREMELY slow and almost always stutters and freezes. I've tried removing the drive from 'shared' and then adding it again, reinstalling my ethernet driver, swapping ethernet ports on the back of my router, and resetting it altogether. Still a slow transfer speed.I use workgroup all around, for xp and for 7.
View 3 Replies View Relatedjust bought a WD my book world edition 2 NAS and have been trying to tranfer files wirelessly to it but a 700mb file is taking 25mins to trans. my book is connected by ethernet to netgear dgnd3300 router and my laptop has sitecom 300n usb doongle.is there some sort of setting i've missed or is this speed normal?
View 5 Replies View RelatedI've recently upgraded the configuration on one of our 1130 series standalone access points. I've implemented RADIUS authentication, WPA2 encryption etc. in an effort to make our network more secure. While this part seems to be working as planned, our data transfer speeds have taken a major hit. On our test AP, with only one laptop connected, the laptop will report a connection at 54 Mbits. When using any speed test service the speed reported is approximately 15 Mbits. We have 100 Mbit internet, and desktops connected to ethernet show much higher speeds. When transferring files via our own LAN, data transfer rates average approximately 2 Mbytes/second. I've tested this on 3 separate laptops, some relatively new, and it seems they all get the same speeds.
Long story short, our wireless seems to be operating under a third of its reported speed.
I have recently purchased a Cisco E4200 to replace my D-LINK DIR-655, which I thought was defective because I was getting slow wirless file transfer speed, regardless of setting, location and client.Using the E4200, when I transfer a file from a PC to another, both connected at 300mb on the 2.4ghz band, the file transfer rate reported by windows 7 and networx is from 2MB/s to 3.5MB/s. I think those transfer rates are not acceptable. Is that a good assumption ? I would expect something in the range of 10MB/s (which is what I get with a cheap dlink router, wired)
I also had great difficulty finding a channel. I had to try them all one-by-one as the auto channel selection made my PCs connect at 130mb.The E4200 is setup as follows:
-WPA-Personal
-Channel 5
-802.11n only
I have tried 3 different computers with different network adapters and they all underperform (IMO..).There are no other wireless networks in my area.I also took the E4200 to my office which is very crowed. Every single channel is occupied by several wireless networks. I get a file transfer speed PC to PC of about 2MB.I basically could have kept my DIR-655 as the speeds are identical.
I have a Cisco ASA 5510. I am trying to copy large files between DMZ and INSIDE network and it is copying at awfully a slow speed. I thought it might have been related to duplex mismatch but it doesn't seem to be. DMZ interface is set at 100 full duplex. I programmed the port on the managed switch where the DMZ uplink is connected to be 100 full duplex. I even hard set the NIC on server to be 100 full. Nothing worked. So, I come to a conclusion it isn't the duplex mismatch but there gotta be something else on Cisco ASA. I was googling for this issue and came across it could be a QoS policy. Now, checking my ASA I see a any to any global service_policy where it is defined to inspect certain protocols where 'netbios' is one of them (among others such as 'ftp', 'tftp', etc. Could the slow copying be related to the above policy? Could there be a bandwidth limitation between DMZ and INSIDE interface? How do I check?
View 5 Replies View Relatedi am running windows server 2008 with the hyper V role installed.i have installed windows 7 Professional as a guest OS. assigned 2 GB of Ram to the machine. the point behind the VM is to virtualize my FTP server and incase a format is required i have the VM file on my 2nd partition, host OS on another. i use Cerberus FTP Server on the Win7 OS. i configured the server to accept SFTP and TLS connections. on the host OS i installed Fire FTP and File Zilla, both Clients will at max download a 4 MB file at 64 KB/Sec .. i have seen both jump to about 80 KB but was only a split second and never held.. however if i login without SFTP and transfer over standard protocol, i download at 1 MB/sec. which is my normal speeds. would this be only to the encryption process?, in the Cerberus Server there are options to adjust download speeds, i have left it default, and altered it to allow its max configuration. My ISP is not limiting any connections that shouldnt be.
View 1 Replies View RelatedI am having incredibly slow connection while transferring files using file sharing.I have the below hardware:
108Mbps TPLINK Wireless Router
TL-WR642G 108Mbps TPLINK Wireless Access Point acting as repeater
Laptops accessing internet and folder sharing enabled for local file transfer
Transfering of files excessively slow (after playing around with the settings was able to get 500KBps). I have set all wireless adapters on the laptops to 802.11g only.Tried setting the router and access point to both 54Mbps and 108Mbps 802.11G only as well as b/g.
1 newer build computer connected to D-link 655 via Cat6.1 laptop computer connected to same D-link 655 via Wireless N minicard. (Intel) (130Mbps connected) Router on a 10 foot shelf, always have full bar in wireless strength on 2nd computer.
Both computers can upload and download as expected from the internet. Transfers between the two computers though are slow. Both computers are loaded with Windows 7. Transferring files to or from the laptop transfers at 1.5MB/sec to 2 MB/sec.
I have two machines that both have WUSB600N wireless network adaptors with a Cisco WRT160N router. The file transfer speeds between the two devices maxes out at 1.6Mbs. If I run speed tests off the internet I hit 15 to 20 and downloads are excellent. I have played with all kinds of settings for the driver and router but nothing seems to work. Both these devices are running Windows 7. I tried a file transfer with an XP device as well and it maxes at about 1.6. how to increase the bandwidth??
View 1 Replies View RelatedI have a RV220W operating in 2.4GHz N-only mode. Channel bandwidth is set to 20MHz, channel to 6 (a site survey shows that channel as completely clear), WPA2/AES. I am connected to a TrendNet wireless bridge. The admin page for that wireless bridge shows a link quality of 100% with a signal strength of 71%. If I select a higher channel (11), the signal strength drops to 51%.
I have a Windows 7 PC connected to the Trendnet bridge and a Windows 7 server connected to the RV220W, both via a 1Gbps LAN port. When I transfer a file from the server to the PC or vice versa, I get a lowsy 2MBps (~20Mbps) transfer rate. That seems awfully slow. I tried channel bonding from 20 to 40 MHz
I am getting very slow window file transfer speed (4 Mbps per second) between two connecting servers in Cisco 6509 switch. I have connect the two laptops in 6509 switch in same module using the same vlan and try to copy the files from one laptop to another and vice versa and got the same speed on 4 to 5 Mbps per second. Switch utilization is not more than 10% and both the laptops are connected in 1 Gbps full duplex.
I have checked by removing the gateway in both laptop but the output is same.
I use my personal laptop at work (an Inspiron E1505). To do so, I had to put it on the network at work. However, when I am home, my laptop runs extremely slow, sometimes taking several minutes just to open a simple program like the calculator. Web surfing is useless even with Road Runner. Any way to make this faster?
I go about removing the computer from the network and would that fix the issue or would I need to wipe the whole thing and start over?
I am noticing the following issue with one of our VPN connections:
Site A is connected to the Internet with an ISA Firewall
Site B is connected to the Internet with a CISCO 5505
Both sites are connected together via a VPN ,Both sites have around a 6MB up and 6MB down connection to the Internet
If I sent a 100MB file from Site A to B it takes around 30-45 minutes to copy, which to me seems excessive.
I've run Wireshark on the server sending the file (from Site A) and the desktop receiving the file (Site B). Initially, the server sending the file was generating a large number of TCP DUP ACK, TCP FAST RETRANSMISSION, TCP PREVIOUS SEGMENT LOST AND TCP OUT-OF-ORDER messages. I narrowed it down to IPv4 Checksum Offload and IPv4 Large Send offload which I disabled on the server. This sped up the file copy and massively reduced the errors in Wireshark, but not to what I think it should be. I then performed Wireshark logging on the desktop receiving the file which was also generating a large amount of TCP DUP ACK, TCP FAST RETRANSMISSION, TCP PREVIOUS SEGMENT LOST AND TCP OUT-OF-ORDER messages. I disabled IPv4 Checksum Offload and IPv4 Large Send offload options on the network card of the desktop and tried resending the file, which made no difference in speed and still generated the above messages in Wireshark.
I have run an mturoute between site A and B and get the following:
C: emp>mturoute.exe 10.0.66.2 (to PC on site B)
* ICMP Fragmentation is not permitted. *
* Speed optimization is enabled. *
* Maximum payload is 10000 bytes. *
.[Code]....
I have been having problems with my Internet the past couple weeks. If I am watching a video, it doesn't matter which site, the video will stop and start from the beginning or the video will just stop altogether and I have to refresh the page. Another problem that happens while browsing, it will take about a minute for a page to load. The computer I am using is wired right into the router.
The rest of the family's computers the apple tv and the roku are wireless. I have been hearing complaints from them and have witnessed the laggyness. While streaming videos on the roku or apple tv, the video will stop and say video is not available or no connection. This is what I get from ipconfig/all
Microsoft Windows [Version 6.2.8400]
(c) 2012 Microsoft Corporation. All rights reserved.
C:WINDOWSsystem32>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Matt-PC[code]......
url...I have 2 PC's connected to a DIR-615 through 802.11n and each have a DWA-130 802.11n adapter. I am running Windows 7 Ultimate 64 bit on both computers. The specs of both systems are very high.I only have these 2 computers on wireless right now. Their signal is full strength, they are less than 10 feet away from the router.I am getting 2.0 MB/s when transferring files between them and although I am not expecting to get 17MB/s, but I should be getting better speed than 2 MB/s.Hard drive specs are Crucial C300 SATA 6.0, WD Caviar Blue SATA 3.0, and WD Caviar Green SATA 3.0. My Green drive reads/writes at 100MB/s, My Blue 125MB/s, and My SSD 225MB/s. So, those are not the bottleneck.Is there any other settings I can try? I have not messed with my DWA-130 settings nor have I messed with Windows.
View 7 Replies View RelatedOld XP and New W7 side by side. Wanting to transfer file, pics, docs, ect. form one to the other. I can see the old XP from the new W7. Through W7 I can get to documents and settings on the old XP, try to open that and says I dont have permission. Old XP c drive shared on network. Still missing something.
View 11 Replies View RelatedI have been trying to get this setup for 2 days now and so far NADA.....
Router: Linksys E3000 - below is a list of all devices connected (hardwired T568B) to the 4 ports with a laptop connected via wireless
1. Main PC - motherboard: ASUS Maximus IV Extreme-Z (dual GB LAN ports)
2. Media Server - motherboard: MSI Z68A-GD80 (dual GB LAN ports)
3. Test Bench AMD PC
4. WD TV Live
Currently: I have all 3 computers running Windows 7 and connected to a Homegroup. I have given the correct permissions to enable sharing of files between each of the 3 computers and can transfer files from one PC to the next w/o any issues.
Desired: I want to connect my Main PC and Media Sever with a crossover cable using the 2nd LAN port on each motherboard, so that I don't have to go through the router to transfer data to and from these 2 PCs. I will have each PC also connected to the Linksys E3000 router via the 1st LAN port on each motherboard to supply the internet connection, so I am also not trying to "share" an internet connection between these 2 PCs. Basically, I want to run my home network through the Linksys E3000 and then a 2nd network for the 2 PCs using the crossover cable.
Current Problem: I disconnected the straight-through cables from the router to each computer from the 1st LAN port. I then connected the crossover cable from the Main PC to the Media Server and setup a new Home network in the Network and Sharing Center in Windows 7. Everything worked and I could transfer data to and from each these 2 PCs, so i know I wired the crossover cable correctly. Then I reconnected the straight-through cables coming from the router to the 1st LAN ports of each mobo, thinking that each PC would auto-detect the internet connection and reacquire my existing home network, enabling an internet connection again. However, this did not happen.
[URL] I also followed this how-to guide on microsoft.com, but when I get to Step 3 where it says that an "Unidentified network icon" will aprear in the Network and Sharing Center, it does not!
From Googling, reading, and troubleshooting I believe I know 2 things:
1. All of the hardware is functioning properly - when the straight-through cables from the router are disconnected, the 2 PCs are networked through the crossover cable and files can be transferred.
2. The problem is with Windows 7 somewhere - I think?
I am having a problem with my newly purchased Linksys E1000 router, I am having terribly slow network speeds while on that network.
Here are my network speeds with The e1000: (wireless) And here are the speeds with my old wrt54g: (Wireless) Here are the results directly hooked up to the modem: (wired)
I've tried setting the MTU to 1500, did a RMA with Linksys to see if it was a hardware problem, did a firmware update to the e1000, disabled DHCP and SPI, reseted my router and my modem....none of those things have worked
My ISP is comcast and I have a Arris TM502G modem
The setup is Windows 7 64 bit transferring a 10 GB file to a Linux Ubuntu distro. Both have 1Gb NICs and the Switch is also a 1Gb switch.
View 2 Replies View RelatedI have 4 systems in my network1)Amd Phenom based HTPC- wired LAN- win764bit ultimate2)Laptop-Wired LAN/Wireless -win764bit home basic3)Work Laptop-Wired LAN/Wireless win764bit ultimate4)Atom based storage server-Wireless only win7 32bit ultimateThe issue I am facing is really really slow data transfer speeds from one system to another 100-200Kbps!!whereas my download speeds are in upwards of 500 kbps with a 4Mbps connection.All the systems run various versions of windows 7 and are part of the same homegroup.the Wireless router I use is this And also have Kaspersky internet security 2012 on all the systems, with the firewall set to recognize my home network as a trusted network
View 2 Replies View Related2-Desktop PCs
2-Qualcomm Atheros AR938x wireless cards, both connected on 5Ghz network at 450 Mbps.Router-E4200, latest firmware, the only 5Ghz network in the area
One PC has a drive bender drive pool on it that I'm trying to read/write from. Testing the pool w/ crystal disk mark on the local pc shows fast speeds (650 MB/s read, 67 MB/s write), so I drive bottlenecks aren't the issue.
Connecting at 450 Mbps i would expect to see something like at least 200 Mbps actual speeds, or is this off? Using LAN Speed test I'm getting 41 write and 52 read. Not great
My work has a main office and a backup office which is off site. What I am trying to do is copy a folder from one computer at the backup site to another computer at the backup site, all while sitting at my computer in the main office. Let's say the two computers at the backup site are called comp1 and comp2.Whether I use Windows Explorer, or .net VB script, or XCOPY from the command prompt, if I try to copy \comp1c_drivefolder to \comp2c_drivefolder from my computer then it takes an extremely long time - around 5 hours for 2Gb of data.
However, if I Remote Desktop into comp1, and from that machine copy C:folder to \comp2c_drivefolder then it only takes 5 minutesI can only assume that when I try to copy the folder from my computer remotely that it is transferring the data from comp1 -> my computer -> comp2, and with the computers being at different sites it's very slow. What I need to know is if I can do this remote copy using VB without the data going via my computer, i.e. straight from \comp1 to \comp2.
I thought this was the way Windows handled copying between networks anyway, i.e. straight from one to the other, my only explanation for the terrible speed is that it is going via my computer. I'm writing a basic folder-backup program in VB and would REALLY like to cut that 5 hour transfer time down to the 5 minutes I know the network can do
I'm having very slow file transfer speeds between the 2 computers on my network. One is a gigabit pc wired (cat6) to the e3000. The other is a wireless N laptop. Both computers running Win7. Speeds are like 1.5 - 2 MB/s. when I connect the laptop to the router with a cable (cat6) I get proper high speed. Trying to figure out if it's a problem with the router or windows or what. Speedtest.net says I'm getting 16 MB/s DL wirelessly to my laptop. Shouldn't wireless N be capable of higher speeds than 1.5 MB/s?? Tests are done approx 10 feet from the router.
View 1 Replies View RelatedHardware Software profile;
Laptop - Windows 7
Desktop - Vista Ultimate SP2
Router - Cisco Linksys E3200
Cables - CAT6
I am a sales engineer, so I use my desktop and laptop all the time. When on road, I sync my desktop with my laptop using a program called ViceVersa. This a very good, reliable syncing program that I have been using for over 10 years ( with upgrades ).
The program allows me to sync my desktop and laptop. The program also shows the data transfer rate during the syncing process. The typical data transfer speed is between 5MB/s and 10MB/s with sometimes up to 12MB/s. A typical sync between the computers will take about 3 - 5 minutes at the ~ 10 MB/s transfer rate using ethernet CAT6 cable inteface. At about 11pm last Tuesday,there was a Windows update on both my Vist and Win7 computers. On wednesday, I went to do a typical sync. The system has dramatically slowed to 59KB/s max. This is about 150 times slower than 5-10MB/s that I was used to for so many years. My typical sync was now taking about 2 hours....unacceptable ! I have tried everything to figure out what is going on and how to fix it but nothing has worked.
Then I tried to see what would happen if I disconnected my ethernet cable ( between the router and the laptop only ) and just sync using the wireless network. With that configuration, the transfer rate is ~ 2.5 MB/s which is not great but is much, much better than 59KB/s. I actually do not know what a reasonable wireless transfer rate should be since I never really did it before due to the faster speed of the wired configuration.
This is just a LAN. Only connecting my Desktop to my Laptop via the Cisco router.
How I can get my wired configuration back up to the 5-10MB/s transfer rate that it once was?
For the past week my internet has been extremely slow, I can watch a South Park episode online and it'll take me at least one hour before I can watch the entire thing because it keeps buffering every 20 seconds. I can barely browse MMO-Champion because it takes one minute to load. Every site takes forever to load. And it's just on my stationary computer. My laptop and mobile phone works just fine. It feels like I've tried everything:
* I've cleaned cache and cookies and stuff like that with CCleaner.
* I've used my console and done all that ipconfig stuff with /flushdns etc etc
* I've used my console and done all that netsh stuff as well
* I've tried to reset my router
* I've tried to use that Microsoft Fix-It program to do whatever it does.
* I've looked through my computer with my anti-virus and anti-malware
* I've installed the latest drivers for my network card/adapter
* I've fixed options on the computer that would allow my computer to perform better
* I've purchased another wireless adapter just to see if that was the problem
* And finally, yes, I've tried restarting the computer
I'm suffering with this annoying internet connection for a months. I'm using a router (tp-link) which I think the source of the problem ,yet I'm not sure. I'm a connected to the router via cable.My download speed is 10kps and below, we already contacted our ISP and change the cable yet the problem is still there.
View 5 Replies View RelatedI just had comcast internet installed, and am using a linksys wireless router (WRT160N). When I connect my netbook to the network it gets 0.7mbps on speedtest.net, when I use my girlfriends laptop it gets 16+mbps. I have tried everything, I am at my whits end. I have updated my firmware, updated windows to the the limit and reset the settings on my router. If I connect my netbook directly to the router I get 20+ but wireless is 0.7 and upload speed stays the same. I am using an HP Mini 210-2000 with windows 7 starter, I have updated it to service pack 1 and have all the windows based drivers installed. I have not tested it on another wireless network to see if it gets the same terrible connection. I don't know if its something with my computer, windows 7 starter, or the way my computer talks to the router
View 3 Replies View RelatedI'm having a big trouble with my internet connection. The Upload speed is extremely slow after i got a new mainboard, that problem appears.[code] I'm tired with my suck internet connection! Upload a 1MB photo to Facebook took me hours..This problem has started for a week.
View 1 Replies View RelatedHaving got a new Windows 7 (64 bit Ultimate) PC, I decided to turn my old PC (XP Pro) into a file server. After much fun with Windows networking, I have one particular problem. Listing files on the server from the Win7 machine is ridiculously slow. A few directories have large numbers of files in them, around 10,000 image files. Browsing to one such folder on Win7, I have timed a listing and it took 48 seconds! That's a very long time to wait for a file listing. I have a network connection monitor running and it doesn't seem to be overloading the network- data was dribbling down the 100Base-T cable at about 200kiloBITS per second. Trying things the other way around, the same folder if placed on the Win7 machine and listed from the old XP machine can deliver a complete listing in about 5 seconds. I'm not sure which end has the problem; either the server is delivering file names very slowly or (my guess) the Win 7 machine is asking for them very slowly, perhaps asking for lots of crap that isn't needed like icons or file dimensions or something.
View 1 Replies View RelatedI am tethering 4g on my Gs3. i am using the wifi tether app rooted. i can connect to my pc and speedtest gives me 25mbps down and about 13 up. but when i connect to my xbox my connection is extremely slow and i only have 3 bars. dont understand whats wrong. and also when i download files it can never go above 1mb. and its not the files because i have downloaded many and its the same story. my brother has the same connection with a nexus and gets 3mb on his files. why my tether is so slow and anything i can do to fix it.
View 1 Replies View RelatedI've recently had Centurylink's Prism service installed and at the same time my internet connection upgraded to 10Mb. When they installed the new service, my modem was replaced with a Cisco DDR 2200-CL modem and router in one. On Monday of this week my internet speeds had dropped. I check my speeds on speedtest.net several times and it was under 1Mb each time. After an hour I called and scheduled a technician to come and check it out. He came the next day, but my speeds were back to almost 10Mb again, and he couldn't find any problems.
View 1 Replies View Related