I want upgrade my switches 2960-24PC-L RAM: 128MB and Flash: 28MB, but in the web page of cisco I see that the requirement of hardware is RAM: 128MB and Flash: 32MB.
I download the IOS file and this file is only 11.2MB so my question is if I can upgrade the IOS because my flash is enough for upload the IOS file.
I have copied the config and vlan.dat files via tftp to the computer and want to import them to a replacement switch. Both switches are 2960 model. I get the config over fine but not sure how to get the vlan.dat file to the flash.
View 1 Replies View RelatedI want to delete the first file c2600-i-mz.122-5d in the flash. Not only delete but also reclaim the memory held by deleted file.I followed a link and i ended up with the c2600-i-mz.122-5d marked as deleted in the flash but the memory was not reclaimed.When I restarted the router, it went to ROMMON mode. This is my understanding when router tried to boot from the flash, It tried to load the first file in the flash. Since the file was marked as deleted therefore Router went to ROMMON mode.Now my question is how could I delete the first file and reclaim the memory on 2600 router?
View 8 Replies View RelatedI'm having an issue with a Cisco 2811 ISR Router. Sh ver command output lists the correct ios that the router used for booting and it says that the ios is stored in flash but when i give "sh flash" command it doesn't display the ios file. Maybe the flash is corrupted or damaged in some way? In the attached file is the output from the "sh ver" and "sh flash" commands.
View 6 Replies View RelatedIn a switch catalyst 2960 the IOS is erasing in flash, for the transfer IOs respalding to flash no function the current command. how is the method.
View 6 Replies View RelatedI tired to upgrade the flash memory on my 871. I have tired to send single break and removing the flash card to drop the 871 to rommon. but no luck, all i get is the below error. I have try restart button on the back and get the same results. How to get the router into rommon mode so i can place the IOS on the flash ?
View 5 Replies View RelatedIf i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies View RelatedWe are going to upgrade our IOS on our WS-C2960G-48TC-L. But before we do that i want to ask whats the best IOS release to choose. Why we want to upgrade is because our switch software now don't support ssh just telnet access
Switch details:
Model: WS-C2960G-48TC-L
SW Version: 12.2(25)SEE2
Image: C2960-LANBASE-M
I was thinking about upgrading the IOS to 12.2(44)SE6 are maybe i should upgrade it to a newer release?
One more thing we have a bunch of stacked 3750 switches, that also need to be upgraded.
I need to upgrade a Catalyst IOS, but I got a bit confused. The catalyst is currently running "c2960-lanbase-mz.122-35.SE5.bin", but I want to upgrade to "c2960-lanbasek9-mz.122-35.SE5.bin", in order to enable ssh. [code] What are the appropriate steps in order to upgrade to "c2960-lanbasek9-mz. 122- 35. SE5.bin". I have downloaded the tar file (c2960-lanbasek9-tar.122-35.SE5.tar)
1) Do I have to delete the old directory (drwx 192 Mar 1 1993 02:07:21 +02:00 c2960-lanbase-mz.122-35.SE5)?
2) Are these the correct steps to download and extract the IOS?
3) Where will the tar files be extracted? Will an new directory be made or do I have to make one manually?
I have a switch 2960-24TC-L with GEC (realised with 2 giga interface uplink) with switch 3750. the configuration is ok, the GEC is up and other feature working. I try to upgrade 2960-24TC-L from 12.2.44SE6 to 12.2.46 or 12.2.5x or 15.0.x...the upgrade it's ok the swithc boot..and the configuraiton is same.. but the giga 0/1 and 0/2 on 2960 not bring up....and the better the interface on 3750 are up.
View 3 Replies View RelatedI am trying to upgrade my cisco WS 2960 24 TC-L switch with the IOS image c2960-lanbasek9-mz.122-55.SE6.bin and my existing IOS image is c2960-lanbasek9-mz.122-50.SE5.bin. when i am copying it to flash, it is getting copied but when i tried to boot it after entering command boot system c2960-lanbasek9-mz.122-55.SE6.bin , it gave me an error.
both flash dir and error are attahced herewith.
I am going to upgrade a number of catalyst 2960s-switcher to the latest IOS- version. The best solution for me would be if all the switches could be reloaded at the same time to shorten the maintenance-windows. So my question is: If I run the upgrade (archive down load -sw) before the maintenance-windows WITHOUT the reload-option, will then the switches continue to run without interruptions with the current IOS- version and config until I run reload manually?
View 3 Replies View RelatedTrying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
I am trying to upgrade my 2960 edge switch through tftpd...i have configured vlan 1 with IP address 172.16.10.1 and tftpd as 172.16.10.2 I am trying to ping tftpd, but I couldn't, but when I try to ping vlan 1 from tftpd, i can?
View 6 Replies View RelatedI have a 10nos of cisco 2960 switches and 1no of cisco 3725 gigabit switch. all 2960 switches are parallaly connected to 3725 switch though fiber.
all the switches are having same vlan and public ips for management.
Now I want to upgrade IOS for all 2960 switches at a time, how to up grade IOS same time for all switches.
I want to upload flash from a sever, as if I was uploading with flash, instead of a browser. I was told something about rfc..(Flash download request)Anyways, is their any sites, etc, that I can use?
View 2 Replies View RelatedWe have a switch Cisco Catalyst 2900 Series XL Model WS-C2924-XL-EN. 8 MB DRAM 4 MB FLASH
I already tried the discussions regarding flash_init dir_flash: boot and the likes.
By the way, I already downloaded the IOS for our switch through Cisco Website. Settings are default through Hyper Terminal
Here's the thing:
Whenever I transfer the .bin file using XMODEM, it prompted an error "Transfer cancelled by remote computer"
I was uploading a big 2gb file to my FTP server, it was all going good and I managed to upload the whole thing hassle free. After I finish I log out, and return about 3 hours later and try to log back in, to no avail.WinSCP gives me the following error:
[code]....
I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies View RelatedI have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber. The link is up on the LST but will not come up on the -S. What command should I use to bring up this link? I have tried no shut from the (Config-if)# prompt.
View 3 Replies View RelatedI am using WiSM in 6509, this WiSM has two controller with the same management IP subnet, I tired to upload the configuration to the TFTP server, but tried many times, one of the controller working well, but the other one always cannot reach the TFTP server, here is the debugger log for both controller
Failed one:
(KGV-WiSM-1) >debug transfer all a enable
(KGV-WiSM-1) >*TransferTask: Nov 10 16:26:08.735: RESULT_STRING: TFTP Config transfer starting.
*TransferTask: Nov 10 16:26:08.735: RESULT_CODE:1
*TransferTask: Nov 10 16:26:32.018: Locking tftp semaphore, pHost=172.16.102.107 pFilename=/KGV.aes
*TransferTask: Nov 10 16:26:32.018: Semaphore locked, now unlocking, pHost=172.16.102.107 pFilename=/KGV.aes
[code].....
why the controller can't upload the file, I can ping both controller and both controllers can ping to the TFTP server.
I can't upload on file-sharing sites , I have tried to upload on wupload.com , fileserve.com , ****file.com and other sites and I click to upload but the progress don't start only stay in 0% I have waited 3 hours to upload a music with 150 MB and still in 0% progress .
View 5 Replies View Relatedwhat is location of flash file in 6500 Series switch and how can we take back of IOS image for 6500 series.
View 4 Replies View RelatedI want to download the iOS update to my Cisco 2800 Series Routers and Cisco Catalyst 2960 Series Switches and leave them there till im ready to install them. Is this possible?
View 1 Replies View Relatedare there any free services where you can remote upload a file (zip file 25MB) and have it sent to me via email as an attachment. not a link where i have to download the file.
View 1 Replies View Relatedi have few catalyst switches (2960, 3750) and i can't upload to them any files by tftp from my laptop, but i can download from them, and this bug don't appears on two routers.I was change tftp server, type of connection (wifi, cable), turn off firewall on win7, but no dice.
View 2 Replies View RelatedI have a 3560x switch with the flash formatted . I have tried to solve the problem by copying the IOS file to the flash. But the boot failed either .I have tried to copy the same IOS by the Xmodem, The boot failed again.My question is how to fixed the boot issues after the flash was formatted?
View 4 Replies View Relatedis it possible to upload a htm file to the router using a command prompt? the page is located at [URL] I want to change the option of Allow All to Restrict Access at 8pm every night?
View 3 Replies View RelatedI have an odd problem with the FTP server. I currently hooked up a 250GB portable HDD which is formatted in NTFS. A single folder in the root of the drive is mounted as the FTP server. Every time I upload a zip or far, the file comes out ends up being uploaded corrupt and double the original file size. I have used 2 FTP clients, using either ASCII or binary. No matter how I go about it, I can't make the files upload at the normal file size. Its not just archives, however, I tried an mp3 and it too got uploaded corrupt and double the size. I then downloaded the mp3 to try and play it but it didn't play in windows media player. However I loaded the 'corrupt mp3 into audacity and the file played like normal.
View 5 Replies View RelatedI am looking for ways to avoid deleting files from the flash in a Switch 2960, I found some scripts TCL / EEM but this switch does not support EEM (IOS c2960-lanbasek9-mz.122-58.SE2.bin).
View 13 Replies View RelatedI've gotten this out of our storage unit here at work: This was not in use, I've restarted it, I can't get into the flash dir,I've tried to restart the switch via the documents I've gotten on the site.I have the lastest iOS version .bin for this switch, but I can't get this to load: here below is what happens when I try.
View 5 Replies View RelatedI have received a sup720-3B from Cisco with an internal 512MB flash(sup-bootdisk). I want to verify what IOS image is on the disk and do not have an spare 6509 chasis. Can I remove the 512 MB flash disk and insert it to my disk0: on my production 6509 with the sup32 that the 720 will repplace and view what is on the disk without corrupting?
View 7 Replies View RelatedI have this 2801 in a critical environment. We had a brief power blip, and even though the router is on UPS, something happened. Anyway, after working with TAC, they determined the flash card had gone corrupt. Lucky for me I had a spare 2801 in my office, I grabbed that flash card and plugged it in and we're back up and going.
TAC sent me a new flash card. No matter what I do, I cannot get IOS to load on this thing! I am stuck in rommon. Here's what I've tried:
tftpdnld in rommon, times out. using another 2801 as a tftp-server. doesn't complete. using xmodem. ugh. never seems to get started. booting the router with a known good flash card, so I can get to ena, and "copy tftp flash".
have used tftpd32, Solar Winds TFTP server, What's Up Gold TFTP server, and open source tftp from sourceforge. With the tftp32, it always gets to exactly 73% download and then times out (it says, I have a feeling it's noty really a timeout). I have tried having the router and tftp server the only devices on a switch, i have tried the router plugged directly into the tftp server with a cross connect cable. No happiness. The open source tftp server reported (and I have to paraphrase, I am not near the router) "client does not support block number recount" or something like that. The client being the 2801.
The iOS file is about 45M. Someone asked me if the flash card was formatted...would that matter? would the tftp even start if it wasn't?
OK, I've gone on long enough. TAC is dispatching a new card AND 2801!