Cisco Switching/Routing :: 2801 - Get IOS On Flash Card?
Mar 15, 2012
I have this 2801 in a critical environment. We had a brief power blip, and even though the router is on UPS, something happened. Anyway, after working with TAC, they determined the flash card had gone corrupt. Lucky for me I had a spare 2801 in my office, I grabbed that flash card and plugged it in and we're back up and going.
TAC sent me a new flash card. No matter what I do, I cannot get IOS to load on this thing! I am stuck in rommon. Here's what I've tried:
tftpdnld in rommon, times out. using another 2801 as a tftp-server. doesn't complete. using xmodem. ugh. never seems to get started. booting the router with a known good flash card, so I can get to ena, and "copy tftp flash".
have used tftpd32, Solar Winds TFTP server, What's Up Gold TFTP server, and open source tftp from sourceforge. With the tftp32, it always gets to exactly 73% download and then times out (it says, I have a feeling it's noty really a timeout). I have tried having the router and tftp server the only devices on a switch, i have tried the router plugged directly into the tftp server with a cross connect cable. No happiness. The open source tftp server reported (and I have to paraphrase, I am not near the router) "client does not support block number recount" or something like that. The client being the 2801.
The iOS file is about 45M. Someone asked me if the flash card was formatted...would that matter? would the tftp even start if it wasn't?
OK, I've gone on long enough. TAC is dispatching a new card AND 2801!
View 1 Replies
ADVERTISEMENT
Feb 26, 2012
Trying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
View 1 Replies
View Related
Feb 6, 2011
When I try to copy ios to one flash in router 2801, I receive the message of of insufficient memory, and have the follow out in the next command: [code] This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.
View 6 Replies
View Related
Dec 3, 2012
how to storage the DHCP IP table in a external flash of a router. This is because the router is switched off and switched on everyday but I want that it remembers which MAC is associated with which IP when it starts again and avoid IP duplicate problems. The command "lease" doesn't seem useful here.
View 4 Replies
View Related
Mar 7, 2011
I have a 2801 router with a HWIC-3G-cdma card that I have inherited from a predicessor. How to use a cellular card on a router and need to get this thing up and running. Any example config that I can see or point me in the right dorection to get this up and running? I have the cellular card set up as Cellular0/1/0 on the interface, I assume that that was done by default, and it has an IP address. The Static Route of 0.0.0.0 0.0.0.0 Cellular0/1/0, in the config with only 2 other interfaces as being direct connection. But that is as far as I recognize. Do I need to set up a router protocol? Which one? How do I use the cellular card? Do I need to have an ISP connection?
View 1 Replies
View Related
Aug 5, 2012
I'm trying to configure intervlan routing between a cisco 2801 router and HP/Amer switches. Using int fa0/1 and subinterfaces I was sure I had it configured correctly, but I cannot ping the default gateways when I place a host in a particular vlan. Below is what I have configured.
HP switch - port 9 connects to fa0/1 on 2801
ip default-gateway 10.1.100.1
trunk 9 Trk1 trunk
trunk 10 Trk2 trunk - to another switch
[code].....
View 4 Replies
View Related
Feb 20, 2012
I am very new at this, but we have a 2801 router running 12.4, a 3560 that acts as the "Core" switch, and a bunch of remote 2960G's that connect via fiber to different buildings.
I am tasked to VLAN this network to reduce broadcast traffic. I started by setting up a VLAN 169 on the "3560" named the VTP domain, changed to version 2, and no password. THe Core switch and remote switch can share the VTP info, I HAD the Router seeing it too (able to ping 192.168.169.1) until I changed the "Domain" and "VTP Version"
The switches see each other fine, my problem is the Router sub interface 0/0.169 I cannot get to see the VTP domain. I imagine because I don't have a "Trunk port" set on the Router, but the option is not there. Meaning I cannot do a "switchport mode trunk" on it. The only thing I see is to make it:
TCRouter(config-subif)#encapsulation dot1Q 169 native
But, my "int fas 0/0" is used now as the main interface for our "only" network 192.168.0.0, do I need to turn this over to a subinterface and make it "Native" then the difference of the subinterfaces will advertise? Here is some of my conf:
Core SW:
TCCoreSW#sh vtp status
VTP Version : running VTP2
Configuration Revision: 8
Maximum VLANs supported locally : 1005
[Code]....
View 10 Replies
View Related
Feb 11, 2013
Im using a 2801 router with a nat configuration.
The issue im having is the nat seems to be allowing only one machine at a time through the nat.
the range i am testing is 192.168.243.0
The firmware is c2801-spservicesk9-m
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
View 5 Replies
View Related
Aug 27, 2012
i want to boot my Router's IOS from TFTP server but when I use the command: boot system tftp c2801-adventerprisek9_ivs-mz.124-24.T7.bin 172.16.10. 200; after that I write-mem, it shows the log:
-Router#wr
-Building configuration...
-ROMMON: out of room in table, cannot set "BOOT"
And when I reload the router, it cannot boot IOS from TFTP Server, sure my TFTP work well and 2801 can ping to TFTP.
View 1 Replies
View Related
Jun 12, 2013
I cannot connect to the Cisco 2801 with console cable. what to do ?
View 1 Replies
View Related
May 7, 2013
I have a 2801 router that I am replacing with a 2911. I know the ports on the 2911 are Gigabits and the 2801 are Fe. I read where the IOS would not support backup and restore on each other . I am attaching a show ver on both routers. I need to know if backup and restore would work and or what other changes would need to get done.
View 1 Replies
View Related
Jan 26, 2012
What is the inrush current (AC Input Surge Current) for the Cisco 2851 router? Is it the same as the router 2801?
View 1 Replies
View Related
Oct 5, 2011
I have a major problem with our core 2801 router. In summary it appears that a staff member disabled password recovery, deleted the IOS and rebooted. Net result is no Rommon and no IOS on the flash. I've read that the Conf-Reg will be reset if I remove the NVRAM but I cannot identify it on the board. If I can get to Rommon I can recover. Currently I don't have Flash reader to restore to flash.
View 2 Replies
View Related
Sep 22, 2012
2801 Router
3550 switch
3500 switch
2 2950 switches
2 pc hosts
Basically I have both PC's pinging 4.2.2.2 DNS, Layer 2, Layer 3 intervlan routing functioning, 2801 Nat is translating, able to ping default gateway of ISP and have configured DNS from what ISP has given under my DHCP scope, however Im still not getting, web pages opening up when i open mazzila or firefox !
View 3 Replies
View Related
Dec 30, 2011
I have a 2651 that has an adsl1-wic that I am using as my DSL router. I recently acquired a 2801 that I want to replace the 2651 with. I configured the 2801 the same way as the 2651 but on a reload I get the statement that says
Setup: New interface NVIO placed in shutdown state
When I do a show interface all of the interfaces show up except the NVIO and I don't have any connectivity to the outside world. I am using Nat since I have a /29 and using nat pool overload. What am I missing? I am running IPVOICEK9-M 12.4.25c on the 2651 and adventerprise 12.4.24.T on the 2801
View 7 Replies
View Related
Mar 26, 2012
I have the above firewall which is working as it should but I have came across an issue with a recent upgrade to Microsoft Exchange 2007 and Outlook 2010 Autodiscovery due to the way the port forwarding has been configured for Outlook Web Access (OWA) on the router.
The router is forwarding OWA requests to the exchange server on port 8080 and the default website in IIS on the Exchange Server under which OWA sits and unfortunately Autodiscovery has been set with an SSL port of 8080. I think the reason for this is that we have an RDP server and the router is forwarding all port 443 requests to this server. Due to this Outlook clients cannot connect to Exchange through autodiscovery and cannot therefore get FREE/BUSY and a few other things.
I have 5 public IP addresses and only use two at the moment, one on the ADSL router and one on this firewall. I have no spare interfaces on either the router or the ADSL router.
My question is, is it possible to have a secondary ip address set on the public facing interface and set different rules for this IP which would allow me to forward requests on that IP to a different server?
Cisco IOS Software, 2801 Software (C2801-ADVSECURITYK9-M), Version 12.4(16b), RELEASE SOFTWARE (fc3)
Building configuration...
Current configuration : 4778 bytes
!
version 12.4
service timestamps debug datetime msec
[Code].....
View 1 Replies
View Related
Mar 24, 2011
1. Do all the 2800 series have a rocker power switch on the rear?
2. Do all 2800 automatically power on when power is connected if the rocker is in the on position?
3. Is it possible to physically damage the flash card in a 2800 router if it was powered off during a write operation?
The story is I have a client who claims that the flash card was damaged due to a power off.
View 2 Replies
View Related
Feb 11, 2013
I want to set up my LAN to have internet access via my 2801 router.The 2801 router is connected to my home ADSL router.Now do I just configure a 0.0.0.0 'gateway of last resort' on the 2801 router pointing to the interface leading to the ADSL router ?Therefore, all traffic from my PCs that is internet bound will head out to the ADSL router and onto the internet.
View 3 Replies
View Related
Feb 13, 2013
I have issue with Cisco Router 2801's Console Port. My student was doing a lab and he said during configuration, Console Port stopped responding. He was in middle of configuration, so now at present, only telnet is able to login on "R2>" user mode, enable password is not set, so getting "R2>en % No password set R2>" I have tried different terminal software but no output from Console Port, changed the Console Cables, replace with working console cables, change speed (baud) settings. Also tried to connect same console with "AUX" port and got same error mentioned above. AUX Port responds but I am not able to change mode (R2#) because of incomplete running-config. it seems "Console Port" is physically damaged.
View 4 Replies
View Related
Apr 15, 2012
I am working on Videoconferencing solution between two location. locations are now being connected through IPSEC site to site VPN. Since we are having a common internet link for VPN as well other corporate use we have to prioritize the internet bandwidth for Videconferencing. is there any way i can prioritise videoconferencing traffic by ports? following are the configs done on the cisco 2801 router with Version 12.4(15)T10.
!interface FastEthernet0/1description ILL_12Mbpsbandwidth 20480ip address 94.*.*.180 255.255.255.248duplex autospeed autopriority-group 1!
ip forward-protocol ndip route 0.0.0.0 0.0.0.0 94.*.*.*
!!no ip http serverno ip http secure-serverip pim ssm default
access-list 199 permit ip host 94.*.42.* host 78.*.*.130 ( VPN peer IPs both ends)priority-list 1 protocol ip high list 199
Interface status
===========(code)
View 6 Replies
View Related
Jun 6, 2011
have remote routers boot and load a config from the flash card. It seems this is possible if the Flash Class is A, according to the Cisco web site using the
boot config flash:<Config file>
where <Config file> is the file on the flash.
Although this can be applied on 2811 routers, they fail to load the file on the flash card. I've since found that this router type has a Class C flash. So the question is, can either:
Is there a similar process for other classes of Flash cards, specifically Class C?
or
The router flash be set as a Class A to support this functionality,
The preferred resolution for this would be the first as there are many remote routers installed a diverse and difficult locations to visit, should a format/rebuild of the flash fail for some reason.
don't ask to list the output of a show boot or show bootvar, neither of these commands work. The Startup/Running config lists the boot config line.
View 5 Replies
View Related
Jun 10, 2012
Can I use Sandisk Compact 4GB Flash card on Cisco 2800 series Routers
View 8 Replies
View Related
Apr 22, 2012
I've gotten this out of our storage unit here at work: This was not in use, I've restarted it, I can't get into the flash dir,I've tried to restart the switch via the documents I've gotten on the site.I have the lastest iOS version .bin for this switch, but I can't get this to load: here below is what happens when I try.
View 5 Replies
View Related
Dec 1, 2011
I have received a sup720-3B from Cisco with an internal 512MB flash(sup-bootdisk). I want to verify what IOS image is on the disk and do not have an spare 6509 chasis. Can I remove the 512 MB flash disk and insert it to my disk0: on my production 6509 with the sup32 that the 720 will repplace and view what is on the disk without corrupting?
View 7 Replies
View Related
Jan 1, 2013
I have a Cisco 2801 with a 4 port Layer2 switch card installed (HWIC-4ESW).
How do I bridge Ethernet0/1 to the 4ESW so if you were to plug a computer into the 4ESW, it would be on the same network as Eth0/1? see my config below:
interface FastEthernet0/1
description Internal Interface
ip address 10.1.2.1 255.255.0.0
[Code].....
View 2 Replies
View Related
Sep 13, 2011
Is there a way to load a spare compact flash with a running-config, ASA IOS, & ASDM software via card reader? I need to load another flash card with all of the settings necessary for normal operation. This "spare" card will replace the flash that is currently in use. The reason for the replacement is capacity and because of changes made to the running-config. The "in-use" card is 256MB, the "spare" one is 512MB. Also, the new card will have a few changes made to the running-config, so it will, in essence, be a reload.
I have a card reader for the compact flash cards. If there is a way to load up this new card using the card reader, without monkeying with the firewall, I would prefer that. Like I said in the previous paragraph, this new flash card will replace the other one, once it's ready.
Hardware: ASA 5510
CF: 256MB (wanting to upgrade to the new 512MB card)
ASA IOS: 8.4
View 15 Replies
View Related
Sep 1, 2012
I want to delete the first file c2600-i-mz.122-5d in the flash. Not only delete but also reclaim the memory held by deleted file.I followed a link and i ended up with the c2600-i-mz.122-5d marked as deleted in the flash but the memory was not reclaimed.When I restarted the router, it went to ROMMON mode. This is my understanding when router tried to boot from the flash, It tried to load the first file in the flash. Since the file was marked as deleted therefore Router went to ROMMON mode.Now my question is how could I delete the first file and reclaim the memory on 2600 router?
View 8 Replies
View Related
Dec 12, 2012
I tired to upgrade the flash memory on my 871. I have tired to send single break and removing the flash card to drop the 871 to rommon. but no luck, all i get is the below error. I have try restart button on the back and get the same results. How to get the router into rommon mode so i can place the IOS on the flash ?
View 5 Replies
View Related
Jul 21, 2012
I had an issue today on a 4507r today where when I formatted the compact flash in slot0: (512mb) it caused the CPU to spike to 100% this took about 1.5 hours and did not cause adjacency loss or any thing, but was worrisome. This was a sup IV is this normal and should u let it complete like I did? Also when I copied the os to it from boot flash it caused the same behavior. I have done this a bunch in 6500 sup 720 without this issue?
View 3 Replies
View Related
Jul 9, 2012
I am trying to research the possiblity of backing up IOS and configurations from an Etherswitch module, and being able to store the files onto the Host Router's flash (3925 ISR). and then being able to recover that IOS and configuration, in case I have to replace the Etherswitch Module.
View 4 Replies
View Related
Feb 26, 2012
Every time I delete the directory flash and reinstall it, I get an error:
Error loading "flash:c2950-i6q4l2-mz.121-12c.EA1.bin"
Error loading "flash:c2950-i6q4l2-mz.121-12c.EA1.bin" Interrupt within 5 seconds to abort boot process.
That is the message I get. It's set to NO manual boot, but it keeps making me manually boot it. I am at a loss, I've done 3 switches and they all keep doing the same thing.
View 6 Replies
View Related
Jan 23, 2013
In a switch catalyst 2960 the IOS is erasing in flash, for the transfer IOs respalding to flash no function the current command. how is the method.
View 6 Replies
View Related
Jan 3, 2013
I recently tried to manually format the flash on a model WS-2960S-48TS-L switch running IOS version 15.0(2)SE. While executing the operation I got the following error - mifs[8]: Failed to create superblock %Error formatting flash (I/O error).As a result the flash is no longer accessible by the switch. I spoke with Cisco and they indicated that a switch reload would remount the flash and make it accessable again but the .bin file would need to be reloaded using the xModem recovery procedure (what a pain).The next IOS version 15.0(2)SE1 will supposedly fix this bug but it has not been released yet. In the meantime if you are running 15.0(2)SE you may want to hold off performing a "format flash:" function on a 2960S.
View 3 Replies
View Related
