Cisco Switching/Routing :: 2651 DSL Router - Replace To 2801?
Dec 30, 2011
I have a 2651 that has an adsl1-wic that I am using as my DSL router. I recently acquired a 2801 that I want to replace the 2651 with. I configured the 2801 the same way as the 2651 but on a reload I get the statement that says
Setup: New interface NVIO placed in shutdown state
When I do a show interface all of the interfaces show up except the NVIO and I don't have any connectivity to the outside world. I am using Nat since I have a /29 and using nat pool overload. What am I missing? I am running IPVOICEK9-M 12.4.25c on the 2651 and adventerprise 12.4.24.T on the 2801
View 7 Replies
ADVERTISEMENT
May 20, 2013
I have cisco 2651. It contains two FastEthernet interfaces: Fa0/0, Fa0/1.Fa0/1 has an ip address. Fa0/0 hasn't an ip address.I need to create monitor session from source Fa0/1 to destination Fa0/0. Then i want to connect my notebook to Fa0/0 to analyze some traffic from port Fa0/1
View 2 Replies
View Related
Dec 21, 2011
I'm trying to replace a ASA 5505 with a Cisco 2801 w/ security bundle.I have gone through a pretty basic set up of configuring what I could and letting the Cisco Config Prof do the security audit to lock it down. I have everything working just fine except for the bandwidth.
As soon as I plug the router in it seems to give all the bandwidth to one computer and the rest of the campus slows down to a crawl.I turned on "fair-queue" and even tried the QoS wizard in CCP, but it seems like thats if you want to prioritize voice over data - which we aren't running VOIP so I don't need.
View 7 Replies
View Related
Feb 11, 2013
Im using a 2801 router with a nat configuration.
The issue im having is the nat seems to be allowing only one machine at a time through the nat.
the range i am testing is 192.168.243.0
The firmware is c2801-spservicesk9-m
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
View 5 Replies
View Related
May 7, 2013
I have a 2801 router that I am replacing with a 2911. I know the ports on the 2911 are Gigabits and the 2801 are Fe. I read where the IOS would not support backup and restore on each other . I am attaching a show ver on both routers. I need to know if backup and restore would work and or what other changes would need to get done.
View 1 Replies
View Related
Feb 11, 2013
I want to set up my LAN to have internet access via my 2801 router.The 2801 router is connected to my home ADSL router.Now do I just configure a 0.0.0.0 'gateway of last resort' on the 2801 router pointing to the interface leading to the ADSL router ?Therefore, all traffic from my PCs that is internet bound will head out to the ADSL router and onto the internet.
View 3 Replies
View Related
Feb 13, 2013
I have issue with Cisco Router 2801's Console Port. My student was doing a lab and he said during configuration, Console Port stopped responding. He was in middle of configuration, so now at present, only telnet is able to login on "R2>" user mode, enable password is not set, so getting "R2>en % No password set R2>" I have tried different terminal software but no output from Console Port, changed the Console Cables, replace with working console cables, change speed (baud) settings. Also tried to connect same console with "AUX" port and got same error mentioned above. AUX Port responds but I am not able to change mode (R2#) because of incomplete running-config. it seems "Console Port" is physically damaged.
View 4 Replies
View Related
Mar 26, 2013
We have 2 x Nortel 8600s (now Avaya) that are 6-7 years old. They have 96 1GB ports on each and we only use about 30 and the CPU average is around 2% and memory is 40% (256mb). Going into 8600s we have 8 x Nortel 5520 48port gig switches.
We want to replace the 8600s at some point and I wondered roughly what Cisco device would possible suit us. We are not after the best high end switches that we will never utilise, but ones that will aid us grow for the next 5 years.
View 16 Replies
View Related
Nov 16, 2011
I have problem with the standby supervisor in 6500 vss and need to replace the supervisor. I have follow how-to on the cisco web site url...
But when i boot the new standby sup720 it comes active and both supervisors is rebooting. I wonder if i can do the replacement without rebooting both active and standy supervisor.
View 1 Replies
View Related
Aug 5, 2012
I'm trying to configure intervlan routing between a cisco 2801 router and HP/Amer switches. Using int fa0/1 and subinterfaces I was sure I had it configured correctly, but I cannot ping the default gateways when I place a host in a particular vlan. Below is what I have configured.
HP switch - port 9 connects to fa0/1 on 2801
ip default-gateway 10.1.100.1
trunk 9 Trk1 trunk
trunk 10 Trk2 trunk - to another switch
[code].....
View 4 Replies
View Related
Feb 26, 2013
We purchased a cisco 1921 router to replace a software firwall not long ago. The router was sold as a firewall with the suggestion that an ASA would be unnecessary.Unfortunately a router does not replace/do the jobs a firewall does, so I looked online and noticed that Cisco do offer firweall security features in one of their IOS.How do I tell if this is implemented on my router?If not, does my IOS support this, or do I need to buy an extension/another version of the IOS?,The version of the IOS I have is: c1900-universalk9-mz.SPA.151-4.M4.bin.
View 3 Replies
View Related
Jan 4, 2013
I am replacing our 2 3750s which are in a stack and are running in VTP server mode for the domain with 2 new 3750Gs. There are 4 trunks to other switches which bare in client mode and 2 trunks to 2 ASAs which are in active/standby mode (one in each switch). Anyway what will happen to the VTP clients when I replace the stack as the revision number will be 1 on the server? The clients will ignore any VTP updates from the server ?
View 6 Replies
View Related
Oct 21, 2012
I have been tasked to replace a failed sup on a 6500 Sup32 running IOS. Now, the primary sup doesnt have a compact flash. I don't have any CF on me. The replacement sup i received also doesnt have a CF.From the cisco website it says that the moment I insert the secondary sup into the chassis. it will automatically download the IOS and boot details from the primary to the secondary sup.
[code]....
View 1 Replies
View Related
Oct 18, 2012
I urgently want to replace a faulty line card WS-X6748-SFP with a new one. The switch concern is a 5609-V-E operating in Virtual Switching System mode.How long do you suggest the down time will be?
View 1 Replies
View Related
Apr 17, 2013
I want to replace an existing 3560 Switch with another switch of the same exact model and IOS. However, this switch that needs to be replaced is the VTP Server of my LAN at this location. When I replace the switch I will just use the same exact running config but I'm concerned about the vlan.dat file. Do I need to copy that file over to the new replacement switch and if so, what is the best way to do that?
View 5 Replies
View Related
May 18, 2012
I have some Cisco 2651 routers, I was trying to implement MPLS on those routers, Can i accomplish this upgrading newer IOS version? link to download the supported IOS.
View 2 Replies
View Related
May 27, 2012
We currently have a WS-C6506 chassis with a line-card WS-X6408A-GBIC. Currently we need to replace the chassis by a Ws-6504-E and also the line-card. My question is: What must buy line-card and meets the same specifications of WS-X6408A-GBIC?.
View 4 Replies
View Related
Feb 27, 2013
I have two like switches in a stack (WS-C3750G-48PS 15.0(1)SE2 C3750-IPBASEK9-M). Switch#1 is the master and is the one that needs to be replaced. Can I force Switch #2 to be the master, then power down switch#1, remove switch#1, insert the replacement, and then power on the newly added switch without shutting down or rebooting switch#2?
View 3 Replies
View Related
Jun 4, 2012
I have a stack of 2960S (c2960s-universalk9-mz.122-55.SE2.bin) and the master has failed (used to have a priority of 14). The second switch has become master (priority 1) as can be seen below: [code]
If I connect a new blank 2960S (same IOS) through the stack ports, will the master sync its config to the new one without causing problems?As I understand the new blank switch will also have a priority of 1 and will by default be numbered as 1. So if the config is correctly synced and I later on want to make switch 1 the master, I need to set the priority: [code]
View 4 Replies
View Related
Apr 22, 2012
I have a question. I have a 6500 with two supervosrs and they both have CATOS. One of them failed and I need to replace. As long as the hardware is the same does the CATOS have to be indentical or can this be different.
View 4 Replies
View Related
Feb 20, 2012
I am very new at this, but we have a 2801 router running 12.4, a 3560 that acts as the "Core" switch, and a bunch of remote 2960G's that connect via fiber to different buildings.
I am tasked to VLAN this network to reduce broadcast traffic. I started by setting up a VLAN 169 on the "3560" named the VTP domain, changed to version 2, and no password. THe Core switch and remote switch can share the VTP info, I HAD the Router seeing it too (able to ping 192.168.169.1) until I changed the "Domain" and "VTP Version"
The switches see each other fine, my problem is the Router sub interface 0/0.169 I cannot get to see the VTP domain. I imagine because I don't have a "Trunk port" set on the Router, but the option is not there. Meaning I cannot do a "switchport mode trunk" on it. The only thing I see is to make it:
TCRouter(config-subif)#encapsulation dot1Q 169 native
But, my "int fas 0/0" is used now as the main interface for our "only" network 192.168.0.0, do I need to turn this over to a subinterface and make it "Native" then the difference of the subinterfaces will advertise? Here is some of my conf:
Core SW:
TCCoreSW#sh vtp status
VTP Version : running VTP2
Configuration Revision: 8
Maximum VLANs supported locally : 1005
[Code]....
View 10 Replies
View Related
May 15, 2012
we have Supervisor Engine 720 10GE (VS-S720-10G) in slot 5 on Catalyst 6509-E. Slot 6 is free. We need to replace VS-S720-10G. Is it possible the following scenario
1. we will insert new VS-S720-10G into the slot 6
2. then we will remove the faulty VS-S720-10G from the slot 5
Will everything work without interuptions. Is any document where I can find step-by-step procedure how to replace VS-S720-10G ?
View 3 Replies
View Related
Feb 17, 2012
Any experience interoperating Nexus 5548 or 5596 with Catalyst 3750 or 4507R?
We're looking into Nexus to replace these switches in the long run.
View 1 Replies
View Related
Nov 30, 2012
I need to replace a faulty fan unit on the catos WS-6509 switch. this Catos switch does not support show inventory so any other catos commands which will show me this part id?
View 2 Replies
View Related
Mar 15, 2012
I have this 2801 in a critical environment. We had a brief power blip, and even though the router is on UPS, something happened. Anyway, after working with TAC, they determined the flash card had gone corrupt. Lucky for me I had a spare 2801 in my office, I grabbed that flash card and plugged it in and we're back up and going.
TAC sent me a new flash card. No matter what I do, I cannot get IOS to load on this thing! I am stuck in rommon. Here's what I've tried:
tftpdnld in rommon, times out. using another 2801 as a tftp-server. doesn't complete. using xmodem. ugh. never seems to get started. booting the router with a known good flash card, so I can get to ena, and "copy tftp flash".
have used tftpd32, Solar Winds TFTP server, What's Up Gold TFTP server, and open source tftp from sourceforge. With the tftp32, it always gets to exactly 73% download and then times out (it says, I have a feeling it's noty really a timeout). I have tried having the router and tftp server the only devices on a switch, i have tried the router plugged directly into the tftp server with a cross connect cable. No happiness. The open source tftp server reported (and I have to paraphrase, I am not near the router) "client does not support block number recount" or something like that. The client being the 2801.
The iOS file is about 45M. Someone asked me if the flash card was formatted...would that matter? would the tftp even start if it wasn't?
OK, I've gone on long enough. TAC is dispatching a new card AND 2801!
View 1 Replies
View Related
Aug 27, 2012
i want to boot my Router's IOS from TFTP server but when I use the command: boot system tftp c2801-adventerprisek9_ivs-mz.124-24.T7.bin 172.16.10. 200; after that I write-mem, it shows the log:
-Router#wr
-Building configuration...
-ROMMON: out of room in table, cannot set "BOOT"
And when I reload the router, it cannot boot IOS from TFTP Server, sure my TFTP work well and 2801 can ping to TFTP.
View 1 Replies
View Related
Jun 12, 2013
I cannot connect to the Cisco 2801 with console cable. what to do ?
View 1 Replies
View Related
Jan 26, 2012
What is the inrush current (AC Input Surge Current) for the Cisco 2851 router? Is it the same as the router 2801?
View 1 Replies
View Related
Oct 5, 2011
I have a major problem with our core 2801 router. In summary it appears that a staff member disabled password recovery, deleted the IOS and rebooted. Net result is no Rommon and no IOS on the flash. I've read that the Conf-Reg will be reset if I remove the NVRAM but I cannot identify it on the board. If I can get to Rommon I can recover. Currently I don't have Flash reader to restore to flash.
View 2 Replies
View Related
Sep 22, 2012
2801 Router
3550 switch
3500 switch
2 2950 switches
2 pc hosts
Basically I have both PC's pinging 4.2.2.2 DNS, Layer 2, Layer 3 intervlan routing functioning, 2801 Nat is translating, able to ping default gateway of ISP and have configured DNS from what ISP has given under my DHCP scope, however Im still not getting, web pages opening up when i open mazzila or firefox !
View 3 Replies
View Related
Mar 26, 2012
I have the above firewall which is working as it should but I have came across an issue with a recent upgrade to Microsoft Exchange 2007 and Outlook 2010 Autodiscovery due to the way the port forwarding has been configured for Outlook Web Access (OWA) on the router.
The router is forwarding OWA requests to the exchange server on port 8080 and the default website in IIS on the Exchange Server under which OWA sits and unfortunately Autodiscovery has been set with an SSL port of 8080. I think the reason for this is that we have an RDP server and the router is forwarding all port 443 requests to this server. Due to this Outlook clients cannot connect to Exchange through autodiscovery and cannot therefore get FREE/BUSY and a few other things.
I have 5 public IP addresses and only use two at the moment, one on the ADSL router and one on this firewall. I have no spare interfaces on either the router or the ADSL router.
My question is, is it possible to have a secondary ip address set on the public facing interface and set different rules for this IP which would allow me to forward requests on that IP to a different server?
Cisco IOS Software, 2801 Software (C2801-ADVSECURITYK9-M), Version 12.4(16b), RELEASE SOFTWARE (fc3)
Building configuration...
Current configuration : 4778 bytes
!
version 12.4
service timestamps debug datetime msec
[Code].....
View 1 Replies
View Related
Apr 15, 2012
I am working on Videoconferencing solution between two location. locations are now being connected through IPSEC site to site VPN. Since we are having a common internet link for VPN as well other corporate use we have to prioritize the internet bandwidth for Videconferencing. is there any way i can prioritise videoconferencing traffic by ports? following are the configs done on the cisco 2801 router with Version 12.4(15)T10.
!interface FastEthernet0/1description ILL_12Mbpsbandwidth 20480ip address 94.*.*.180 255.255.255.248duplex autospeed autopriority-group 1!
ip forward-protocol ndip route 0.0.0.0 0.0.0.0 94.*.*.*
!!no ip http serverno ip http secure-serverip pim ssm default
access-list 199 permit ip host 94.*.42.* host 78.*.*.130 ( VPN peer IPs both ends)priority-list 1 protocol ip high list 199
Interface status
===========(code)
View 6 Replies
View Related
Jan 1, 2013
I have a Cisco 2801 with a 4 port Layer2 switch card installed (HWIC-4ESW).
How do I bridge Ethernet0/1 to the 4ESW so if you were to plug a computer into the 4ESW, it would be on the same network as Eth0/1? see my config below:
interface FastEthernet0/1
description Internal Interface
ip address 10.1.2.1 255.255.0.0
[Code].....
View 2 Replies
View Related
