Cisco Switching/Routing :: 2801 Cannot Connect With Console Cable
Jun 12, 2013I cannot connect to the Cisco 2801 with console cable. what to do ?
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 2801 Router Console Port Not Working?
Feb 13, 2013I have issue with Cisco Router 2801's Console Port. My student was doing a lab and he said during configuration, Console Port stopped responding. He was in middle of configuration, so now at present, only telnet is able to login on "R2>" user mode, enable password is not set, so getting "R2>en % No password set R2>" I have tried different terminal software but no output from Console Port, changed the Console Cables, replace with working console cables, change speed (baud) settings. Also tried to connect same console with "AUX" port and got same error mentioned above. AUX Port responds but I am not able to change mode (R2#) because of incomplete running-config. it seems "Console Port" is physically damaged.
View 4 Replies View RelatedCisco Switching/Routing :: Can't Configure 831-k9 Via Console Cable
May 30, 2012I purchased an old cisco 831 for practical studies for a cisco certification. I purchased the console cable (serial/rj45) and a usb->serial converter cable. However when I open my terminal application (tera term) After I select the right com port (3) and make sure the connection settings are right. It will just sit idle and not show any data from the device. Was I sold a faulty device? It lights up and has three lights on.
Everytime I look at a manual or cisco video I am given the impression the terminal application will just automatically connect. But whenever I try I get nothing.
Cisco Switching/Routing :: Cannot Administer New Catalyst 2960 Switch Via Console Cable
Dec 12, 2012I planed to configure a new catalyst 2960 switch with console cable.
During the boot, all seems ok. but from my terminal client, I can't have access to configuration mode.Keyboard or Terminal client is not sending commands to the switch.
The terminal is blocked on this line Compiled Tue 28-Sep-10 13:44 by prod_rel_team.what can I do to get access to the switch? [code]
Cisco Switching/Routing :: Linksys SRW2048 - Connection Between Console Cable And Hyper-terminal
Feb 16, 2012So I have read about proper procedure involving the connection between a console cable and Hyper-terminal. I have also tried plugging into a network port to obtain an IP Address but nothing seems to work. When powering on the switch I see that it lights up, hear fans spin and assume it has booted properly. I'm using Hyperterminal on Windows Xp Pro SP3 and I've also tried minicom in Fedora.
And just FYI Hyperterminal was set to the proper:
Bits per second: 38400
Data bits: 8
Parity: None
Stop Bits: 1
Flow Control: None
Cisco Switching/Routing :: USB Console Cable For 3012 Blade Center Switch Module
Jul 27, 2011I have 6 of these WS-CBS3012-IBM modules that need to be configured but I cannot access the USB console port. I was told I could just get any DB9- to- USB cable and that would work. I did buy a DB9-to-USB cable and it did not work. I looked up the installation guide for this module and it just said the console cable is DB9-to-USB but with no part number.
View 3 Replies View RelatedCisco Switching/Routing :: Can't Connect To Console Switch Sge2010
Mar 18, 2013I can't connect to the console of switch cisco sge2010, I tried several console cables and none worked for me, I followed step by step manuals and nothing.
Also try the web 192.168.1.254 according to the manual but when I connect from the laptop to do ping to the switch doesnt work.
Cisco Switching/Routing :: Can't Connect To Console On 3750X Stack Members
Oct 23, 2012I have a 3750X stack of 6 switches, I have a terminal server console server plugged into the console ports of all 6 switches. I am having a strange issue where I can connect to the master via the console, get a login prompt then I can log in, but when I try and connect to any of the members then I get a prompt "Press RETURN to get started" When I push return, it just loops back to the same prompt again:
switch-6 con0 is now available
Press RETURN to get started.
switch-6 con0 is now available
Press RETURN to get started.
I can connect to the stack via SSH fine etc. I am running 15.0(1)SE2. The stack is configured for TACACS+ auth via Cisco ACS.
Switch# Role Mac Address Priority Version State
----------------------------------------------------------
*1 Master f0f7.55ba.2700 15 1 Ready
2 Member f0f7.5541.da00 14 1 Ready
3 Member a493.4c1e.4b80 13 1 Ready
4 Member f0f7.5585.cb80 12 1 Ready
5 Member a44c.1120.8e80 11 1 Ready
6 Member a493.4cc0.fa80 10 1 Ready
Cisco Switching/Routing :: When Connect Router 2821 Through Console / Get Error Message At Regular Interval Of Time
Feb 9, 2013When i connect the Router 2821 through the Consol get error message at regular interval of time %ENVMON-4-FAN_LOW_RPM: Fan 1 service recommended.
View 2 Replies View RelatedCisco Switches :: What Kind Of Cable Is Required To Connect To Console On Linksys SRW2024
Apr 26, 2011What kind of cable is required to connect to the Console on a Linksys SRW2024 switch ? ( I've lost the original cable )I use the following settings: Speed 38400, 8 bits, no parity, no flow control and stop bits 1I have tried a serial cable, no go.I have tried a null modem cable with partial handshaking, no go.I have tried a null modem cable with full handshaking, no go.For the null modem cables, if I use it to connect between computers using hyperterminal it works very well. What I type on one computer appears on the other computer's screen.However, I can't get anything out of the switch. I've tried pressing Enter repeatedly, resetting the switch with the Console cable on, etc.
View 2 Replies View RelatedCisco Switching/Routing :: Configuring Intervlan Routing Between 2801 And HP Switches?
Aug 5, 2012I'm trying to configure intervlan routing between a cisco 2801 router and HP/Amer switches. Using int fa0/1 and subinterfaces I was sure I had it configured correctly, but I cannot ping the default gateways when I place a host in a particular vlan. Below is what I have configured.
HP switch - port 9 connects to fa0/1 on 2801
ip default-gateway 10.1.100.1
trunk 9 Trk1 trunk
trunk 10 Trk2 trunk - to another switch
[code].....
Cisco Switching/Routing :: VTP Trunking On 2801
Feb 20, 2012I am very new at this, but we have a 2801 router running 12.4, a 3560 that acts as the "Core" switch, and a bunch of remote 2960G's that connect via fiber to different buildings.
I am tasked to VLAN this network to reduce broadcast traffic. I started by setting up a VLAN 169 on the "3560" named the VTP domain, changed to version 2, and no password. THe Core switch and remote switch can share the VTP info, I HAD the Router seeing it too (able to ping 192.168.169.1) until I changed the "Domain" and "VTP Version"
The switches see each other fine, my problem is the Router sub interface 0/0.169 I cannot get to see the VTP domain. I imagine because I don't have a "Trunk port" set on the Router, but the option is not there. Meaning I cannot do a "switchport mode trunk" on it. The only thing I see is to make it:
TCRouter(config-subif)#encapsulation dot1Q 169 native
But, my "int fas 0/0" is used now as the main interface for our "only" network 192.168.0.0, do I need to turn this over to a subinterface and make it "Native" then the difference of the subinterfaces will advertise? Here is some of my conf:
Core SW:
TCCoreSW#sh vtp status
VTP Version : running VTP2
Configuration Revision: 8
Maximum VLANs supported locally : 1005
[Code]....
Cisco Switching/Routing :: 2801 - Get IOS On Flash Card?
Mar 15, 2012I have this 2801 in a critical environment. We had a brief power blip, and even though the router is on UPS, something happened. Anyway, after working with TAC, they determined the flash card had gone corrupt. Lucky for me I had a spare 2801 in my office, I grabbed that flash card and plugged it in and we're back up and going.
TAC sent me a new flash card. No matter what I do, I cannot get IOS to load on this thing! I am stuck in rommon. Here's what I've tried:
tftpdnld in rommon, times out. using another 2801 as a tftp-server. doesn't complete. using xmodem. ugh. never seems to get started. booting the router with a known good flash card, so I can get to ena, and "copy tftp flash".
have used tftpd32, Solar Winds TFTP server, What's Up Gold TFTP server, and open source tftp from sourceforge. With the tftp32, it always gets to exactly 73% download and then times out (it says, I have a feeling it's noty really a timeout). I have tried having the router and tftp server the only devices on a switch, i have tried the router plugged directly into the tftp server with a cross connect cable. No happiness. The open source tftp server reported (and I have to paraphrase, I am not near the router) "client does not support block number recount" or something like that. The client being the 2801.
The iOS file is about 45M. Someone asked me if the flash card was formatted...would that matter? would the tftp even start if it wasn't?
OK, I've gone on long enough. TAC is dispatching a new card AND 2801!
Cisco Switching/Routing :: 2801 Router NAT Configuration
Feb 11, 2013Im using a 2801 router with a nat configuration.
The issue im having is the nat seems to be allowing only one machine at a time through the nat.
the range i am testing is 192.168.243.0
The firmware is c2801-spservicesk9-m
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
Cisco Switching/Routing :: 2801 Cannot Boot IOS From TFTP
Aug 27, 2012i want to boot my Router's IOS from TFTP server but when I use the command: boot system tftp c2801-adventerprisek9_ivs-mz.124-24.T7.bin 172.16.10. 200; after that I write-mem, it shows the log:
-Router#wr
-Building configuration...
-ROMMON: out of room in table, cannot set "BOOT"
And when I reload the router, it cannot boot IOS from TFTP Server, sure my TFTP work well and 2801 can ping to TFTP.
Cisco Switching/Routing :: Replacing 2801 With 2911 Router
May 7, 2013I have a 2801 router that I am replacing with a 2911. I know the ports on the 2911 are Gigabits and the 2801 are Fe. I read where the IOS would not support backup and restore on each other . I am attaching a show ver on both routers. I need to know if backup and restore would work and or what other changes would need to get done.
View 1 Replies View RelatedCisco Switching/Routing :: Inrush Current Information In 2801
Jan 26, 2012What is the inrush current (AC Input Surge Current) for the Cisco 2851 router? Is it the same as the router 2801?
View 1 Replies View RelatedCisco Switching/Routing :: 2801 Password Recovery Disabled
Oct 5, 2011I have a major problem with our core 2801 router. In summary it appears that a staff member disabled password recovery, deleted the IOS and rebooted. Net result is no Rommon and no IOS on the flash. I've read that the Conf-Reg will be reset if I remove the NVRAM but I cannot identify it on the board. If I can get to Rommon I can recover. Currently I don't have Flash reader to restore to flash.
View 2 Replies View RelatedCisco Switching/Routing :: 2801 / 3550 - HTTP Web Not Coming On?
Sep 22, 20122801 Router
3550 switch
3500 switch
2 2950 switches
2 pc hosts
Basically I have both PC's pinging 4.2.2.2 DNS, Layer 2, Layer 3 intervlan routing functioning, 2801 Nat is translating, able to ping default gateway of ISP and have configured DNS from what ISP has given under my DHCP scope, however Im still not getting, web pages opening up when i open mazzila or firefox !
Cisco Switching/Routing :: 2651 DSL Router - Replace To 2801?
Dec 30, 2011I have a 2651 that has an adsl1-wic that I am using as my DSL router. I recently acquired a 2801 that I want to replace the 2651 with. I configured the 2801 the same way as the 2651 but on a reload I get the statement that says
Setup: New interface NVIO placed in shutdown state
When I do a show interface all of the interfaces show up except the NVIO and I don't have any connectivity to the outside world. I am using Nat since I have a /29 and using nat pool overload. What am I missing? I am running IPVOICEK9-M 12.4.25c on the 2651 and adventerprise 12.4.24.T on the 2801
Cisco Switching/Routing :: 2801 Secondary IP / Port Forwarding?
Mar 26, 2012I have the above firewall which is working as it should but I have came across an issue with a recent upgrade to Microsoft Exchange 2007 and Outlook 2010 Autodiscovery due to the way the port forwarding has been configured for Outlook Web Access (OWA) on the router.
The router is forwarding OWA requests to the exchange server on port 8080 and the default website in IIS on the Exchange Server under which OWA sits and unfortunately Autodiscovery has been set with an SSL port of 8080. I think the reason for this is that we have an RDP server and the router is forwarding all port 443 requests to this server. Due to this Outlook clients cannot connect to Exchange through autodiscovery and cannot therefore get FREE/BUSY and a few other things.
I have 5 public IP addresses and only use two at the moment, one on the ADSL router and one on this firewall. I have no spare interfaces on either the router or the ADSL router.
My question is, is it possible to have a secondary ip address set on the public facing interface and set different rules for this IP which would allow me to forward requests on that IP to a different server?
Cisco IOS Software, 2801 Software (C2801-ADVSECURITYK9-M), Version 12.4(16b), RELEASE SOFTWARE (fc3)
Building configuration...
Current configuration : 4778 bytes
!
version 12.4
service timestamps debug datetime msec
[Code].....
Cisco Switching/Routing :: 3750v2 What Kind Of Cable Should Be Used To Connect
Jan 18, 2012According to documentation Cisco RPS 675 should have support for Cisco 3750v2 switch(WS-C3750V2-48PS).What kind of cable should be used to connect them?Cisco RPS has 16 pins and 3750v2 has 22 pins.I could not find that type of cable,
View 2 Replies View RelatedCisco Switching/Routing :: Setup LAN To Have Internet Access Via 2801 Router
Feb 11, 2013I want to set up my LAN to have internet access via my 2801 router.The 2801 router is connected to my home ADSL router.Now do I just configure a 0.0.0.0 'gateway of last resort' on the 2801 router pointing to the interface leading to the ADSL router ?Therefore, all traffic from my PCs that is internet bound will head out to the ADSL router and onto the internet.
View 3 Replies View RelatedCisco Switching/Routing :: 2801 - Prioritize Internet Bandwidth For Videoconferencing
Apr 15, 2012I am working on Videoconferencing solution between two location. locations are now being connected through IPSEC site to site VPN. Since we are having a common internet link for VPN as well other corporate use we have to prioritize the internet bandwidth for Videconferencing. is there any way i can prioritise videoconferencing traffic by ports? following are the configs done on the cisco 2801 router with Version 12.4(15)T10.
!interface FastEthernet0/1description ILL_12Mbpsbandwidth 20480ip address 94.*.*.180 255.255.255.248duplex autospeed autopriority-group 1!
ip forward-protocol ndip route 0.0.0.0 0.0.0.0 94.*.*.*
!!no ip http serverno ip http secure-serverip pim ssm default
access-list 199 permit ip host 94.*.42.* host 78.*.*.130 ( VPN peer IPs both ends)priority-list 1 protocol ip high list 199
Interface status
===========(code)
Cisco Switching/Routing :: Unable To Console / Ssh To 6513
Aug 9, 2012I have a 6513 with redundant sup 720-3B's that I cannot get onto. In short, one of the power supplies failed, it still passes traffic but I can't console or ssh to the box. Other than the two sup 720's, I have a 4 port 10gig card, a 16 port GBIC Card and an IDS module. I have tried removing the 10Gig, IDS and one of the sup's but still don't get anything on the console. I have rebooted the entire chassis and don't get anything on my console while booting. I have tried changing the speed of my terminal to every setting available incase someone has changed it at some stage but to no avail. I have tried swapping sup's, using only one at a time in the chassis but not getting anything. Is there anything else I can try to get onto this chassis? The power supply is a 3000w with a 32amp input. The failed power supply had tripped a switch, when i brought it back up, the power supply came out but the output failed LED is on. My #questions are, is there anything else I can do to try get onto the console, and is the power supply goosed when the RED LED is lit? I have reseated the power supply also but the same result.
View 2 Replies View RelatedCisco Switching/Routing :: 2811 - How To Copy IOS Using Console
Jan 4, 2012i have 2811 router and i am coneccted via concole so i want to copy the 2811 ios to my PC is that possible?
how or give my the right decument to do this.
* idon't want to use TFTP becuse i have no ethernet connection to the router(only concole)
Cisco Switching/Routing :: USB Console Into 2911 Router
May 19, 2013I have installed a cisco 2911 router and the cisco usb console drivers on my pc, win 7 64 bit.however when I use putty and open the com port assigned it just goes blank, I am using the usb port on my laptop to connect and using the cisco usb console cable provided
View 1 Replies View RelatedCisco Switching/Routing :: 3560 Don't Get Any Output From Console
Apr 3, 2012I have a 3560-24ps, and I'm having issues with it booting. When I power the device up all the front panel lights come on like normail, and then the system light starts flashing like normal, but after 5 - 6 seconds the system light goes off. I don't get any output from the console, and the fans still run.
View 5 Replies View RelatedCisco Switching/Routing :: Connect 3550 Cable Modem (dynamic Ip)
Oct 8, 2012I have a Home Virgin media cable connection at home. the only way to get this working with my Cisco gear is by putting the superhub on modem mode.On modem mode, it becomes just a dumb modem assigning and IP via DHCPI can get the switch to get an IP address from the modem with
no switchport
ip address dhcp
then I have created
0.0.0.0 0.0.0.0 fa0/48
to route traffic to the port connected to the mode,The switch gets the assigned Ip address from the modem but it does not route internet traffic.
From the different vlans and subnets on the switch, I can ping the modem.
From the switch I can ping 8.8.8.8
From the machines, i cannot ping 8.8.8.8
On my machines, what should be the gateway? the vlan SVI, the modem's IP address, The fa0/48 ip address? I have tried them all with no success.
Cisco Switching/Routing :: Catalyst 2960 - Can SFP+ Cable Be Used To Connect As Stack?
Apr 25, 2013I have two Cisco 48 port Catalyst 2960-S series SI. Instead of buying the pricy stack modules can I only use the SFP+cable to connect them as stack? which type of SFP+cable should I buy? do I need any license to use those SFP ports?
View 9 Replies View RelatedCisco Switching/Routing :: Bridging Routed Ethernet Ports To L2 Switchports On 2801?
Jan 1, 2013I have a Cisco 2801 with a 4 port Layer2 switch card installed (HWIC-4ESW).
How do I bridge Ethernet0/1 to the 4ESW so if you were to plug a computer into the 4ESW, it would be on the same network as Eth0/1? see my config below:
interface FastEthernet0/1
description Internal Interface
ip address 10.1.2.1 255.255.0.0
[Code].....
Cisco Switching/Routing :: 3560 To Make Sure Not To Take Over Console Connection
Jun 11, 2013I have two 3560s that i would like to upgrade. But first i would like to make -absolutely- sure i dont wind up in a situation where i have to roll back over a console connection.to the day i still cant understand why oh why someone removed (or chose not to implement it everywhere) tftpdnld from rommon ;)
View 8 Replies View RelatedCisco Switching/Routing :: 3750 Turn Off 802.1x Console Messages
Dec 16, 2012Is there a way to turn off 802.1x authentication messages to the console of a 3750 switch? The issue we have is that we like to monitor the terminal when remotely configuring our switches. However, every time a computer authenticates to the network we get messages and sometimes quite a few depending on the situation.
View 3 Replies View Related