Im using a 2801 router with a nat configuration.
The issue im having is the nat seems to be allowing only one machine at a time through the nat.
the range i am testing is 192.168.243.0
The firmware is c2801-spservicesk9-m
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
I have 1 2611xm router and 1 2801 router. For my own lab purpose, i want to configure them back to back to support voice services. I don't know what configuration will be required at each end. in 2611xm, i have NM-2V and its also detecting the card, so i hope it will work ? also what commands i need to run on both ends .
View 1 Replies View RelatedI have a 2801 router that I am replacing with a 2911. I know the ports on the 2911 are Gigabits and the 2801 are Fe. I read where the IOS would not support backup and restore on each other . I am attaching a show ver on both routers. I need to know if backup and restore would work and or what other changes would need to get done.
View 1 Replies View RelatedI have a 2651 that has an adsl1-wic that I am using as my DSL router. I recently acquired a 2801 that I want to replace the 2651 with. I configured the 2801 the same way as the 2651 but on a reload I get the statement that says
Setup: New interface NVIO placed in shutdown state
When I do a show interface all of the interfaces show up except the NVIO and I don't have any connectivity to the outside world. I am using Nat since I have a /29 and using nat pool overload. What am I missing? I am running IPVOICEK9-M 12.4.25c on the 2651 and adventerprise 12.4.24.T on the 2801
I want to set up my LAN to have internet access via my 2801 router.The 2801 router is connected to my home ADSL router.Now do I just configure a 0.0.0.0 'gateway of last resort' on the 2801 router pointing to the interface leading to the ADSL router ?Therefore, all traffic from my PCs that is internet bound will head out to the ADSL router and onto the internet.
View 3 Replies View RelatedI have issue with Cisco Router 2801's Console Port. My student was doing a lab and he said during configuration, Console Port stopped responding. He was in middle of configuration, so now at present, only telnet is able to login on "R2>" user mode, enable password is not set, so getting "R2>en % No password set R2>" I have tried different terminal software but no output from Console Port, changed the Console Cables, replace with working console cables, change speed (baud) settings. Also tried to connect same console with "AUX" port and got same error mentioned above. AUX Port responds but I am not able to change mode (R2#) because of incomplete running-config. it seems "Console Port" is physically damaged.
View 4 Replies View RelatedI have to configure failover on both router. if one get fail then the other router should be dial.Physical connection
•1. Two routers (Cisco 2801) are connecting with splitter through RJ 11 port.
•2.Only one ISP link is coming in splitter.
Requirement: As per as customer requirement. He wants redundancy with in both 2 routers. If one goes down then the other router come up. And same configuration on 2801_R2 router. I am planing to do HSRP on our lan network (2801R1,2801R2 ehternet interface which connected to switch). from switch i will create two default route with (next hope) virtual ip address.
I'm trying to configure intervlan routing between a cisco 2801 router and HP/Amer switches. Using int fa0/1 and subinterfaces I was sure I had it configured correctly, but I cannot ping the default gateways when I place a host in a particular vlan. Below is what I have configured.
HP switch - port 9 connects to fa0/1 on 2801
ip default-gateway 10.1.100.1
trunk 9 Trk1 trunk
trunk 10 Trk2 trunk - to another switch
[code].....
I am very new at this, but we have a 2801 router running 12.4, a 3560 that acts as the "Core" switch, and a bunch of remote 2960G's that connect via fiber to different buildings.
I am tasked to VLAN this network to reduce broadcast traffic. I started by setting up a VLAN 169 on the "3560" named the VTP domain, changed to version 2, and no password. THe Core switch and remote switch can share the VTP info, I HAD the Router seeing it too (able to ping 192.168.169.1) until I changed the "Domain" and "VTP Version"
The switches see each other fine, my problem is the Router sub interface 0/0.169 I cannot get to see the VTP domain. I imagine because I don't have a "Trunk port" set on the Router, but the option is not there. Meaning I cannot do a "switchport mode trunk" on it. The only thing I see is to make it:
TCRouter(config-subif)#encapsulation dot1Q 169 native
But, my "int fas 0/0" is used now as the main interface for our "only" network 192.168.0.0, do I need to turn this over to a subinterface and make it "Native" then the difference of the subinterfaces will advertise? Here is some of my conf:
Core SW:
TCCoreSW#sh vtp status
VTP Version : running VTP2
Configuration Revision: 8
Maximum VLANs supported locally : 1005
[Code]....
I have this 2801 in a critical environment. We had a brief power blip, and even though the router is on UPS, something happened. Anyway, after working with TAC, they determined the flash card had gone corrupt. Lucky for me I had a spare 2801 in my office, I grabbed that flash card and plugged it in and we're back up and going.
TAC sent me a new flash card. No matter what I do, I cannot get IOS to load on this thing! I am stuck in rommon. Here's what I've tried:
tftpdnld in rommon, times out. using another 2801 as a tftp-server. doesn't complete. using xmodem. ugh. never seems to get started. booting the router with a known good flash card, so I can get to ena, and "copy tftp flash".
have used tftpd32, Solar Winds TFTP server, What's Up Gold TFTP server, and open source tftp from sourceforge. With the tftp32, it always gets to exactly 73% download and then times out (it says, I have a feeling it's noty really a timeout). I have tried having the router and tftp server the only devices on a switch, i have tried the router plugged directly into the tftp server with a cross connect cable. No happiness. The open source tftp server reported (and I have to paraphrase, I am not near the router) "client does not support block number recount" or something like that. The client being the 2801.
The iOS file is about 45M. Someone asked me if the flash card was formatted...would that matter? would the tftp even start if it wasn't?
OK, I've gone on long enough. TAC is dispatching a new card AND 2801!
i want to boot my Router's IOS from TFTP server but when I use the command: boot system tftp c2801-adventerprisek9_ivs-mz.124-24.T7.bin 172.16.10. 200; after that I write-mem, it shows the log:
-Router#wr
-Building configuration...
-ROMMON: out of room in table, cannot set "BOOT"
And when I reload the router, it cannot boot IOS from TFTP Server, sure my TFTP work well and 2801 can ping to TFTP.
I cannot connect to the Cisco 2801 with console cable. what to do ?
View 1 Replies View RelatedWhat is the inrush current (AC Input Surge Current) for the Cisco 2851 router? Is it the same as the router 2801?
View 1 Replies View RelatedI have a major problem with our core 2801 router. In summary it appears that a staff member disabled password recovery, deleted the IOS and rebooted. Net result is no Rommon and no IOS on the flash. I've read that the Conf-Reg will be reset if I remove the NVRAM but I cannot identify it on the board. If I can get to Rommon I can recover. Currently I don't have Flash reader to restore to flash.
View 2 Replies View Related2801 Router
3550 switch
3500 switch
2 2950 switches
2 pc hosts
Basically I have both PC's pinging 4.2.2.2 DNS, Layer 2, Layer 3 intervlan routing functioning, 2801 Nat is translating, able to ping default gateway of ISP and have configured DNS from what ISP has given under my DHCP scope, however Im still not getting, web pages opening up when i open mazzila or firefox !
I have the above firewall which is working as it should but I have came across an issue with a recent upgrade to Microsoft Exchange 2007 and Outlook 2010 Autodiscovery due to the way the port forwarding has been configured for Outlook Web Access (OWA) on the router.
The router is forwarding OWA requests to the exchange server on port 8080 and the default website in IIS on the Exchange Server under which OWA sits and unfortunately Autodiscovery has been set with an SSL port of 8080. I think the reason for this is that we have an RDP server and the router is forwarding all port 443 requests to this server. Due to this Outlook clients cannot connect to Exchange through autodiscovery and cannot therefore get FREE/BUSY and a few other things.
I have 5 public IP addresses and only use two at the moment, one on the ADSL router and one on this firewall. I have no spare interfaces on either the router or the ADSL router.
My question is, is it possible to have a secondary ip address set on the public facing interface and set different rules for this IP which would allow me to forward requests on that IP to a different server?
Cisco IOS Software, 2801 Software (C2801-ADVSECURITYK9-M), Version 12.4(16b), RELEASE SOFTWARE (fc3)
Building configuration...
Current configuration : 4778 bytes
!
version 12.4
service timestamps debug datetime msec
[Code].....
I am working on Videoconferencing solution between two location. locations are now being connected through IPSEC site to site VPN. Since we are having a common internet link for VPN as well other corporate use we have to prioritize the internet bandwidth for Videconferencing. is there any way i can prioritise videoconferencing traffic by ports? following are the configs done on the cisco 2801 router with Version 12.4(15)T10.
!interface FastEthernet0/1description ILL_12Mbpsbandwidth 20480ip address 94.*.*.180 255.255.255.248duplex autospeed autopriority-group 1!
ip forward-protocol ndip route 0.0.0.0 0.0.0.0 94.*.*.*
!!no ip http serverno ip http secure-serverip pim ssm default
access-list 199 permit ip host 94.*.42.* host 78.*.*.130 ( VPN peer IPs both ends)priority-list 1 protocol ip high list 199
Interface status
===========(code)
I have a Cisco 2801 with a 4 port Layer2 switch card installed (HWIC-4ESW).
How do I bridge Ethernet0/1 to the 4ESW so if you were to plug a computer into the 4ESW, it would be on the same network as Eth0/1? see my config below:
interface FastEthernet0/1
description Internal Interface
ip address 10.1.2.1 255.255.0.0
[Code].....
I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
about to install first UC320w and wanted some sample 800 series router configurations showing required port fowarding, ACL entries and QoS examples.
View 5 Replies View RelatedI have recently configured a cisco 1921 router for internal routing on my network. Here is what i am trying to accomplish:
Main network 10.65.1.0 mask 255.255.255.0- all office devies and computers.
Second network 10.65.2.0 mask 255.255.255.0 - All plant equipment machinery and production lines
i have configure gig 0/0 for my company network and gig 0/1 for my plant network. I can ping the router from both networks but am unable to route traffic betwenn them. what am i missing?
the router IPSec VPN config for remote users using Cisco VPN Client 5.0.07
Router 3945 IOS C3900-UNIVERSALK9-M Version 15.1(4)M4
Here is VPN related config part and log from router and client.
aaa new-model
!
!
aaa authentication login default none
aaa authorization network default none
!
!
crypto isakmp policy 5
encr aes 256
authentication pre-share
[Code]...
I highlighted strings with possible problems of of unabling to connect but doesn't know what to do with it.
i have floor with 10 users with DATA vlan and VOICE vlan , WIRELESS vlan , my questions :
Basement floor Core switch fiber -----> my floor switch <--------my internet DSL router827
- In this scenraio the switch in my floor will be as L2 or L3 ?
- What is the configuration it will be in the switch if it is L3 ?
- What is the configuration it will be in DSL router with Subinterfaces for each vlan ?
Any sample for configuration that can work for switch nad DSL router ?
I am new user of cisco router i can access the hardware and login in the account but the problem is if i use the command "enable" asking for a password, old I.T. personnel who setup this router already resign.
View 2 Replies View Relatedmy trouble is I have a cisco 857w and I have never configured a wireless config for a cisco router before. Ok so i have had a go through the web interface (i know, last resort) and still no joy
Basically what im looking for is to have a visible (broadcast ssid) network with a password (WEP/WPA/WPA2, not picky) and it to be joined to the same vlan as the ethernet ports (VLAN 1).
I have a Cisco 2811 Router. I have two VLANS on the router. The first one of course is VLAN 1 and the second one is one that I created from reading everything from this forum.. it is called VLAN 531
On VLAN one I have an IP address of 10.8.1.1 and on VLAN 531 I have an IP Address of 172.16.1.1, now what I can do is this... I can.. from a workstation on the 10.8.0.0 segment, ping 172.16.1.1 and one server on that segment that has an IP address of 172.16.1.50, which is fine, but what I really want to be able to do is ping our email server which is on a 10.21.0.0 segment and I cannot. Any commands on what I would need to do to make this work as I would like the 172.16.0.0 segment to ping any other part of my LAN of my choosing.
Here is my current config, how to enable and setup NVI on a cisco 1941 router.i think it would fix my issue but i'm unclear on how to implement it to test.
i would like to be able to access an internal server from an outside address.
Will 2811 Router with 4 switch port module, How to do dual ISP configuration on this router.
View 10 Replies View RelatedI have a 1711 Catalyst router hooked up behind a cable modem. I configured the router, copied running-config to start up-config then wrote it to memory with "write mem". I unplugged router to move it and when I plugged it back in, I had to start from scratch.
Is this normal, or should router be able to save configuration if powered down?
BTW, I'm using Putty to access router console. Is that the hot setup for Windows 7 or is there something better?
I currently am trying to program the config for a 1720 router however i cannot get the config to stick. I boot up to the command prompt put in all the configurations use the "write mem" command and then hard reset the router but when it boots back up I get the initial system configuation dialog.
I have tried booting to the rommon prompt and typing "confreg" and following the prompts keeping all options set to no except for this setting
"enable "ignore system config info"? y/n [n]: Y"
Is set to yes. but when i get to the end of the config it just loops and starts over with
"you wish to change the configuration? y/n [n]: Y"
If i choose yes it loops if I choose no it goes back to the rommon prompt.
i have to configure 80 Cisco 876 routers, so i planned to copy config via tftp from one configured router to PC, edit it in text editor (change ip addresses, dhcp pools, vpn keys...) and then copy it via tftp to another router, etc... Configuration looks fine and it works when i paste it in cli, but when i copy it via tftp i'm getting strange problems like dhcp not working or snmp not accessible. Am I missing something.
Here's config from router with dhcp problem:
ROUTER#sh run
version 15.1
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers(code)
I have customer that we have configured netflow on the 2821 router that their traffic is on. Currently the company they have contracted with for the analysis is seeing data duplication. Below is the configuration for the interface and the router
Cisco 2821;
interface GigabitEthernet0/0
description TVC-FI-Ethernet-Fiber-Ethernet link
ip address 216.255.164.33 255.255.255.248 secondary
ip address 192.168.5.1 255.255.255.0 secondary
ip address 216.255.166.129 255.255.255.128 secondary
[code]....
I have not been able to figure out the resolution. The basic premise is to have 3 inside vlan networks controlled by a 1900 series router. Then have that primary LAN router connect to the inside of my ASA5505 Basic, then go out to my ISP Gateway. I have tried hundreds of different static route configurations on my router and asa. I have tried equally as many NAT and PAT configurations, but nothing seems to work. I have even tried using all the commands (specific to my topography of course) on this weblink from cisco: url...
View 12 Replies View Related