Cisco Switching/Routing :: Editing And Copying Configuration 876 Router To Another
Oct 3, 2012
i have to configure 80 Cisco 876 routers, so i planned to copy config via tftp from one configured router to PC, edit it in text editor (change ip addresses, dhcp pools, vpn keys...) and then copy it via tftp to another router, etc... Configuration looks fine and it works when i paste it in cli, but when i copy it via tftp i'm getting strange problems like dhcp not working or snmp not accessible. Am I missing something.
Here's config from router with dhcp problem:
ROUTER#sh run
version 15.1
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers(code)
View 2 Replies
ADVERTISEMENT
Jul 27, 2012
i have a 7206 router to be used as a gateway for internet router 7206 inerfaces are connected directly to cisco switch 2960g note that 7600 work only at 1 gega , and cant be used for 10 or 10 . im looking forward to use router 7600 instaed of 7206 i copied the config of 7206 and pased in 7600 but some commands which are under interfaces command was not accepted here is the config which as not accepted in 7600 router
%%%%%%%%%%%%%%%%%%%%%%%%
duplex auto
speed auto
media-type rj45
negotiation auto
%%%%%%%%%%%%%%%%%%%%%%%%
note that the 4 lines above was not accpted in 7600. does these commands will affect the new config ?i just want to ask before im trying to apply this config to production network?
View 3 Replies
View Related
Feb 9, 2012
I just received a DIR-615 in the post that I bought on eBay. I currently have a DI-624 at home .Will I be able to copy the configuration from my old router to this new one?
View 3 Replies
View Related
Jan 25, 2012
I am trying to configure this router to obtain an IPv6 address from my ISP who offers a dual stack IPv4/IPv6 DHCPv6 Prefix Delegation service.
I did a WAN packet capture to see the type of DHCPv6 packets the router sends to the ISP in order to obtain an IPv6 address and I saw that the router is sending DHCPv6 solicitation packets of type IA_NA i.e. for Identity Association for Non-temporary Address. However, most ISPs that offer a dual stack IP4/IPv6 service, they use DHCPv6 Prefix Delegation in which case the router is expected to send DHCPv6 solicitation packets of type IA_PD i.e. for Identity Association for Prefix Delegation.
I then downloaded its configuration file and saw the following:
dhcpv6c = {}
dhcpv6c[1] = {}
dhcpv6c[1]["renewTime"] = "3600"
[Code].....
So, the option for the DHCPv6 client to perform a prefixDelegation request is disabled. Does that mean that if I set this flag to "1" it is going to work? Well, I edited the configuration file and changed this flag but the router refuses to load it! It complains about the file being changed. How does it know that? Is it computing some type of checksum? How can I manually edit this flag and update the router's configuration?
View 2 Replies
View Related
Nov 5, 2011
Here is logs from 2650 router.
2650XM#$ Nov 5 23:10:13.929 MST: %SIGNATURE-3-NOT_ABLE_TO_PROCESS: %ERROR: Not able to process Signature in flash:2600-adventerprisek9-mz.124-25d.bin.Nov 5 23:10:41.963 MST: %SIGNATURE-3-NOT_ABLE_TO_PROCESS: %ERROR: Not able to process Signature in nvram:.
Nov 5 23:11:26.642 MST: %SYS-2-EXCEPTIONDUMP: System Crashed, Writing Core....2650XM#$
Right now i am able to access the router . whats this error about -- is router going to crash or reboot?
View 26 Replies
View Related
Feb 28, 2012
Our office lan network is in 192.168.0.0/16 with 300 nodes and 30 server .Since its a large broadcast domain some times it takes large time for copying files.How can we avoid this problem with out changing the subnet.Also how to avoid broadcast storm.we are using cisco 2950 series switch.
View 10 Replies
View Related
Jun 4, 2012
I was upgrading IOS on 4507 R with dual supervisor.I download the IOS on Active supervisior and did reboot.After reboot i login to switch then i got switch standby prompt.I found that after reboot active supervisior became standby supervisior.
Now new IOS is on standby supervisior.Need to confirm below..So this means that IOS does not syn within the supervisiors as compared to config right ?
-Which command i can use that will copy IOS from standby supe to Active supe??
-Which command i can use that will show both active and standby supe with new IOS?
-Is there any command that i can use to switchover from active to standby supe??
View 3 Replies
View Related
Aug 21, 2012
i hav asa5520 i copying configuration from PIX to ASA5520 (7.2) everything working fine bt problem is that after sometime my DMZ interface losing connectivity ...
View 1 Replies
View Related
Jul 6, 2012
How do i copy the configuration file from a switch to a storage device (USB)
View 1 Replies
View Related
Jul 17, 2012
I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
View 1 Replies
View Related
Jun 13, 2012
about to install first UC320w and wanted some sample 800 series router configurations showing required port fowarding, ACL entries and QoS examples.
View 5 Replies
View Related
Mar 27, 2012
I have recently configured a cisco 1921 router for internal routing on my network. Here is what i am trying to accomplish:
Main network 10.65.1.0 mask 255.255.255.0- all office devies and computers.
Second network 10.65.2.0 mask 255.255.255.0 - All plant equipment machinery and production lines
i have configure gig 0/0 for my company network and gig 0/1 for my plant network. I can ping the router from both networks but am unable to route traffic betwenn them. what am i missing?
View 8 Replies
View Related
Feb 11, 2013
Im using a 2801 router with a nat configuration.
The issue im having is the nat seems to be allowing only one machine at a time through the nat.
the range i am testing is 192.168.243.0
The firmware is c2801-spservicesk9-m
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
View 5 Replies
View Related
Dec 2, 2012
the router IPSec VPN config for remote users using Cisco VPN Client 5.0.07
Router 3945 IOS C3900-UNIVERSALK9-M Version 15.1(4)M4
Here is VPN related config part and log from router and client.
aaa new-model
!
!
aaa authentication login default none
aaa authorization network default none
!
!
crypto isakmp policy 5
encr aes 256
authentication pre-share
[Code]...
I highlighted strings with possible problems of of unabling to connect but doesn't know what to do with it.
View 4 Replies
View Related
May 21, 2013
i have floor with 10 users with DATA vlan and VOICE vlan , WIRELESS vlan , my questions :
Basement floor Core switch fiber -----> my floor switch <--------my internet DSL router827
- In this scenraio the switch in my floor will be as L2 or L3 ?
- What is the configuration it will be in the switch if it is L3 ?
- What is the configuration it will be in DSL router with Subinterfaces for each vlan ?
Any sample for configuration that can work for switch nad DSL router ?
View 3 Replies
View Related
Jan 11, 2012
I am new user of cisco router i can access the hardware and login in the account but the problem is if i use the command "enable" asking for a password, old I.T. personnel who setup this router already resign.
View 2 Replies
View Related
Sep 23, 2012
my trouble is I have a cisco 857w and I have never configured a wireless config for a cisco router before. Ok so i have had a go through the web interface (i know, last resort) and still no joy
Basically what im looking for is to have a visible (broadcast ssid) network with a password (WEP/WPA/WPA2, not picky) and it to be joined to the same vlan as the ethernet ports (VLAN 1).
View 1 Replies
View Related
May 22, 2013
I have a Cisco 2811 Router. I have two VLANS on the router. The first one of course is VLAN 1 and the second one is one that I created from reading everything from this forum.. it is called VLAN 531
On VLAN one I have an IP address of 10.8.1.1 and on VLAN 531 I have an IP Address of 172.16.1.1, now what I can do is this... I can.. from a workstation on the 10.8.0.0 segment, ping 172.16.1.1 and one server on that segment that has an IP address of 172.16.1.50, which is fine, but what I really want to be able to do is ping our email server which is on a 10.21.0.0 segment and I cannot. Any commands on what I would need to do to make this work as I would like the 172.16.0.0 segment to ping any other part of my LAN of my choosing.
View 12 Replies
View Related
Dec 9, 2012
Here is my current config, how to enable and setup NVI on a cisco 1941 router.i think it would fix my issue but i'm unclear on how to implement it to test.
i would like to be able to access an internal server from an outside address.
View 4 Replies
View Related
Dec 9, 2011
Will 2811 Router with 4 switch port module, How to do dual ISP configuration on this router.
View 10 Replies
View Related
Nov 10, 2011
I have a 1711 Catalyst router hooked up behind a cable modem. I configured the router, copied running-config to start up-config then wrote it to memory with "write mem". I unplugged router to move it and when I plugged it back in, I had to start from scratch.
Is this normal, or should router be able to save configuration if powered down?
BTW, I'm using Putty to access router console. Is that the hot setup for Windows 7 or is there something better?
View 5 Replies
View Related
Aug 15, 2012
I currently am trying to program the config for a 1720 router however i cannot get the config to stick. I boot up to the command prompt put in all the configurations use the "write mem" command and then hard reset the router but when it boots back up I get the initial system configuation dialog.
I have tried booting to the rommon prompt and typing "confreg" and following the prompts keeping all options set to no except for this setting
"enable "ignore system config info"? y/n [n]: Y"
Is set to yes. but when i get to the end of the config it just loops and starts over with
"you wish to change the configuration? y/n [n]: Y"
If i choose yes it loops if I choose no it goes back to the rommon prompt.
View 5 Replies
View Related
May 5, 2013
I have customer that we have configured netflow on the 2821 router that their traffic is on. Currently the company they have contracted with for the analysis is seeing data duplication. Below is the configuration for the interface and the router
Cisco 2821;
interface GigabitEthernet0/0
description TVC-FI-Ethernet-Fiber-Ethernet link
ip address 216.255.164.33 255.255.255.248 secondary
ip address 192.168.5.1 255.255.255.0 secondary
ip address 216.255.166.129 255.255.255.128 secondary
[code]....
View 2 Replies
View Related
Feb 27, 2013
I have not been able to figure out the resolution. The basic premise is to have 3 inside vlan networks controlled by a 1900 series router. Then have that primary LAN router connect to the inside of my ASA5505 Basic, then go out to my ISP Gateway. I have tried hundreds of different static route configurations on my router and asa. I have tried equally as many NAT and PAT configurations, but nothing seems to work. I have even tried using all the commands (specific to my topography of course) on this weblink from cisco: url...
View 12 Replies
View Related
Mar 3, 2013
i am currently using 2 DSL WIFI modem and wants to combine them to my RV042 dual wan router but as i set them up using WAN1 and Wan2 as "Obtain IP Automatically" there is no internet connection?
View 2 Replies
View Related
Jan 4, 2012
I have an 877W router that I would like to have a 2nd pre-configured backup for. I was thinking of getting another 870 series (probably an 877) router, as the more expensive wireless option is not actually required. Am I right to assume that I could simply copy the contents of my current config.txt file onto the second router?
View 4 Replies
View Related
Jul 5, 2012
I've recently purchased a Cisco catalyst 2960S-24TS-L & setup 3 V LANS 10 (no current IP),20 (192.168.2.1) and 30 (192.168.3.1) to reflect the router V LAN configuration & ip information. When connecting my PC to the switch to test connectivity on (2.1 & 3.1) I'm unable to connect to the the net but can successfully ping GW (int FE0.20 & FE0.30) 192.168.2.1 & 3.1.
The router is an Cisco 1801 & it seems this is where the configuration issue is but I'm unable to figure out how to complete the setup. It has been quite awhile since I've configured a Cisco router.
Ive never had this router connected to a switch so all router switch ports are in the default VLAN1 (192.168.1.2), with FE0 disabled. In trying to get the switch to communicate with the router I made the following router config modifications.
FE0 enabled with subinterfaces configured
FE0.10-currently no ip
FE0.20-192.168.2.1/27
FE0.30-192.168.3.1/27
I have two issues I want to resolve:
1) I do not know what additional steps are required to allow 2.1.& 3.1 V LANs to access the net.
2) I want to disable VLAN1 if possible & use the network IP for VLAN10 (192.168.1.0). I'm unsure how to do this as any change on VLAN1 immediately breaks router access and the router reconfiguration becomes more complicated with changes to the FW ACL etc.
View 2 Replies
View Related
Apr 28, 2011
When pusing configs using tftp, for example using Ciscoworks, does it push out an entire new config or does it just edit specific changes?
View 1 Replies
View Related
Jan 26, 2012
I would like to edit .cfg configuration file of Cisco SLM2008. However, I can't read the file because I don't have a good editor(.cfg is a binary file).
View 1 Replies
View Related
Feb 19, 2013
We have a few voip phones, with the voip server in the building. The hard phones have been trouble, with dropouts and occasional bad quality phone calls. The sip provider is absolutely hopeless. The modem router is a DG834Gv5 with fw V1.6.00.33. There is no option in the router interface to edit QoS settings. How can I improve our voip system? have an iphone connected to a handset or something, could that? We are using an iPECS-50A voip server and iPECS LIP-8012D phones.
My second question is in regards to auto attendants. I need to edit auto attendant settings. I assume this is done using the VOIP server. When the IP address is entered, I get a station program option and Admin & Maintenance. Where would I find auto attendant?
View 1 Replies
View Related
Dec 28, 2012
I have two mac laptops and am trying to copy a directory with a number of PDFs in it. The files aren't particularly large, but there are many of them. At some point in the process the router stops and must be turned off and on before it will respond again either wirelessly or wired. I have tried the same experiment with both devices wired and the router works fine. I have tried changing the MTU, channel, beacon setting, etc. as other forum posts have tried. I tried reflashing the firmware, resetting to factory defaults and reconfiguring. So far no success. Cisco support wants me to return the router. Frankly I'm at the point of considering the former Linksys/Cisco products complete rubbish. I am going to have to buy a new router even if I return this one since I can't be without a router for any length of time.
View 8 Replies
View Related
Mar 7, 2012
I have a client that is running ACS 5.3 as a VM in ESX 4.1. The client wants their VMWare admins to have the ability to shut down the ACS server during maintenance etc... I know I could create a CLI user with admin priviliges, however, assigning full admin priviliges is beyond the scope of what the user requires. They simply want a user account with the added privilige of performing a halt from the CLI. In the CLI Reference Guide for ACS.
So is it possible to create an account with user priviliges, then modify its permissions to allow for a halt?
View 3 Replies
View Related
Jul 25, 2012
I found how to change the mac address by registry editing in windows for ethernet but can`t find a mac address for wlan... even in linux i m not able to change mac address for wlan using macchanger?
View 2 Replies
View Related