Here is my current config, how to enable and setup NVI on a cisco 1941 router.i think it would fix my issue but i'm unclear on how to implement it to test.
i would like to be able to access an internal server from an outside address.
I have a 1941W that has a connection to my ISP (Gi0/1) and another connection to a remote lab (Gi0/0). Everything is working fine how it is setup. All my traffic from my internal networks can access the Internet and devices on the 192.168.201.0 /24 can access the Internet and the lab 10.89.0.0/16.
Now I want to have two devices (192.168.201.51 & .147) use Gi0/0 when accessing host 63.85.190.67. There is no route to this subnet since it reside in the remote lab. Here is what I have right now. How would I setup a PBR to have those two host use Gi0/0 when accessing 63.85.190.67
interface Vlan192
ip address 192.168.201.1 255.255.255.0
ip nat inside
ip virtual-reassembly (code)
I have a Cisco router 1941 connected to a switch. I'm configuring the w LAN- AP and i need to have the wireless devices have an ip in the same range of the wired devices.Since i cant use the same ip range on the gig0/1 and the V LAN 1 for the wireless, i wanted to know how to config the giga0/1 connected to the switch to act as a layer 2 port and i keep the ip on the v LAN 1.
View 9 Replies View RelatedI have a 1941 router tt needs to be setup with the range of WAN ip addresses ip nat inside outside don't allow me to use it..How can i configure on the router to ensure from outside i'm able to access to firewall (129.2.1.2) ?
View 4 Replies View RelatedI have a pair of 6500's setup with VSS and there is currently only one link between then. However one end of the link is on Po10 and the other end is on Po25. If I move the Po25 over to Po10, will things break? It seems to be working fine now. I'm about to add a second link and I'm concerned about the current configuration. It makes more sense to me to have both ends of the same link on the same port-channel ID. I've seen documentation which states otherwise however.
interface Port-channel10
no switchport
no ip address
[Code]....
I am trying to setup intervlan configuration and stuck on a problem. Here are the details:
1. Switches Catalyst 3750-x (as core switch) and Catalyst 2960S (as access switch)
2. Both switches have VLAN 20 and VLAN 1 on their database and both are active. BTW, after I figure out how to properly configure interVLAN routing the native VLAN 1 will not be used anymore. This is just an initial test.
3. VLAN 20 SVI interface (IP 192.168.20.200) on 3750 is up and can be pinged from catalyst 2960.
4. VLAN 1 SVI interface (IP 192.168.170.200) on 3750 is up and also can be pinged from Catalyst 2960.
5. Catalyst 3670 can ping a client computer (IP 192.168.20.10) connected to Catalyst 2960.
6. IP route enabled on 3750
7. Trunking is enabled on etherchannel connecting both 3750 and 2960
8. Client computer in VLAN 20 (connected to 2960) can ping VLAN 20 SVI interface 192.168.20.200 on switch 3560.But, the client computer in VLAN 20 can not reach any computer in VLAN 1 and vice versa. Strangely, the switches which these computers are connected to can ping each other or any connected client copmuters without any problem as described above.
I am having an issue accessing the internet from a PC on the LAN. I have configured the PC with the gateway of the router infront of the ISP to test. I can ping from the router to google or any other internet IP. From the PC I can ping to the GIG0/1 (Inside LAN IP) and the GIG0/0 (Outside WAN IP going to ISP) but I can't ping the Next Hop IP of the ISP or anything past that. If I do a trace route from the PC to the google IP address it hits the GIG0/1 Inside LAN IP Address but fails from there. Here is a cut down snap shot of the router configure
[code]....
im having trouble setting up a vpn for a 1941 router this is what I have setup
crypto isakmp policy 10
encr aes 256
authentication pre-share
crypto isakmp key ########## address 63.247.48.50
[code]....
my whole problem comes about when i need to Nat 192.168.1.0 to 10.12.14.0/24 before it goes through the tunnel.
I did have a router cisco 1941 but can not do ipsec with it,i did take a smart net.
View 3 Replies View RelatedI have a 1941 integrated services router that will not keep the configs. After several atempts of saving running config to the startup config, then rebooting the device. I am having to reload the configs manually from TFTP because they are gone. I have also tryed the "wr" command to see. Is there a proper way to shutdown this particular type of router?
View 2 Replies View RelatedI have a cisco router 1941 and i have uploaded before evaluation license , now i have already bought cisco security license .I have already installed on cisco router , but the problem the router is still using the evaluation license not the new license .
RSP#sh flash:
-#- --length-- -----date/time------ path
1 55088360 Oct 10 2012 06:04:10 +00:00 c1900-universalk9-mz.SPA.151-4.M4.bin
2 2903 Feb 4 2013 12:23:32 +00:00 cpconfig-19xx.cfg
[Code].....
What is the procedure to reset a 1941 router to factory defaults? I just recieved my1 1941 router. I connected it up to my Mac using USB. I got loged in using the cisco/cisco login and it said it will only work once and that I should create a new account. So I entered the command as directed on the screen and it gave my an error about the command. I verified it three times and each time it rejected. While I was looking online for an answer the connection timed out and now I can't get back in.
View 1 Replies View RelatedRouter 1941 is installed with additional 4 Gig-interfaces card; we have 4 ADSL Router with 4 MB connections. I need to connect all the ADSL connection to the router 4 port and combine them into 16 MB, is there any way to combine 4 Gig interfaces?
View 4 Replies View RelatedI have a Cisco 1941 K9 Router. I want to add POE functionaltiy to it. Specifically I want a 4 port EHWIC POE switch to power a couple of AP's.
This is what I understand I need; Upgrade/replace the internal power supply with PWR-1941-POE power supply, This is supplied with a fan replacement also (not yet purchased).buy 1 x EHWIC-4ESG (4 port switch)buy 1 x ILPM-4 (inline daughter card / power supply board) I think the real question here is the 4 port switch... there are two types available one is EHWIC-4ESG=the other is EHWIC-4ESG-P=
Is there any difference between these two switch modules? or are they the same and the more expensive "P" version is simply supplied with the ILPM-4 daughter card for POE?
I have recieved via courier today 1 x EHWIC-4ESG, and found a ILPM-4 on ebay for a good price. WIll this provide POE through the switch EHWIC-4ESG?
I Have a Cisco 1941 router which had its GE0/1 port burnt out and we have since plugged in a module with 4 fast ethernet ports. I need to reconfigure the router such that at least one of the Fast ethernet ports can server the purpose of the GE0/1. GE0/0 connects to our Service provider and GE0/1 connected to the inside network.Currently, while connected to one of the ethernet ports, i can telnet into the router on the address 192.168.29.1. when i'm on the router, i can ping our remote site, network address 192.168.24.0 with no problem, but when i use the command "Ping 192.168.24.0 source 192.168.29.1" there is no response.
View 1 Replies View RelatedMy questions is can a 4 port PoE switch module (EHWIC-4ESG-P) and a 8 port switch module (EHWIC-D-8ESG) be used at the same time in a Cisco 1941 router?
View 1 Replies View RelatedWe purchased this router with the cisco IOS software installed. I've installed the Vista driver on my win 7 box. I believe that should work. I installed Putty to termainl in and I'm using a USB connection. I cannot even log into the router. I thought I was going to see some kind of setup wizard using the CISCO software so I would use a GUI and get things moving. I've got loads of reference material with command etc. but I just can't connect to the router to make it happen.
View 3 Replies View RelatedI am setting up a Cisco 1941 series router for our department in Denmark. As we quickly relised we had to reset the router to it's defult settings. As we comunicated with the router thorugh HyperTerminal, the router asked me to restart. After we did so the router only sends encrypted messages wich is unreadable. We neither get any respons in the terminal when we try to write commands back to the router.We have tried to use different terminal programs as well as the USB port on the router.
View 4 Replies View RelatedI have a 1941 that I am going to deploy with a HWIC-D-9ESW switch module (I only need 3 switch ports but need the PoE). I am going to hang a 1262 autonomous AP off one of the ports but I need to configure MAC address port-security so that only that AP can pass traffic. I know the switch modules are 'almost' exactly like a switch for commands but I can't seem to enable or configure any port-security settings. Is port-security no available on the switch modules?
View 3 Replies View RelatedI have a strange issue that I am having an issue figuring out. I am trying to login to the 1941 router through the console port. When I enter the username and password, which I just set, it fails. I am able to login under a different login but when I try to enter the enable mode the enable password doesn't work, which I just set as well. I can login with the TACACS+ login from a SSH session. Here is the line config:
line con 0
exec-timeout 15 0
logging synchronous
[Code].....
We configured 1941 k9 router for inernet purpose
ip name-server 218.248.255.146ip name-server 218.248.255.212multilink bundle-name authenticated!!!license udi pid CISCO1941/K9 sn FHK144773MG!!interface GigabitEthernet0/0 ip address x.x.x.x 255.255.255.248 ip nat outside ip virtual-
[Code]....
when i configured access-list 2 permit any . Internet working on local systems but we are not able to connect telnet.
I have a 1941 router configured for Policy based routing with two ISPs.Two static default routes configured to point the gateways of respoective ISPs with same metric.But the problem is, packets are going throug the one ISP only while doing traceroute.
N/W connectivity:
ISP1-----> <----------------------> LAN1
| Router |
ISP-------> <----------------------> LAN 2
Below is my configuration :
Current configuration : 5958 bytes
!
! Last configuration change at 05:18:56 UTC Mon Jun 25 2012
!
version 15.0
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
I have 2 cisco 1941/K9 vpn router. I have configured both with LAN ip address given by our vpn provider which is 172.10.10.1 and the other is 172.10.20.1. Both IP addresses are configured to GigabitEthernet port 0/0 on both routers.
1. Is it possible to configure our own set of ip address like 10.71.10.1 and 10.71.50.1 on the GE 0/0 port?
2. Or can we configure our own set of ip addresses (10.71.10.1 and 10.71.50.1) to GigabitEthernet port 0/1 and maintain the other ip addresses on port 0/0?
The first purpose is to have our own set of ip addresses for LAN connection and I will be able to connect or telnet whichever ip address or port is up.
I have this Cisco 1941 router with two Ethernet ports g0/0 and g0/1. The g0/0 is connected to office LAN with internet access. As my office LAN is DHCP, it will assigned a IP address for g0/0 since this g0/0 is configured as "ip address dhcp". Now my question is that i have a group of 5 pcs, namely PC1, PC2, PC3, PC4 and PC5 that is connected to the switch and one of the ports of this switch is connected to g0/1 of Cisco 1941. Is it possible that let say PC2 and PC3 (both DHCP enabled) could access the internet access from g0/0 and at the same time, the office LAN assigned IP address for PC2 and PC3 automatically?
Office Lan with internet access (DHCP) (Default gateway 10.0.0.1)
|
|
g0/0 (DHCP enable) (DHCP assigned IP address 10.0.0.138)
Cisco router 1941
g0/1
|
|
HP Switch
|
PC1 PC2 PC3 PC4 PC5
Is this operation possible? if possible, how to configure inside the router 1941 to achieve this objective?
I have just set up my Cisco 1941 router to my cable internet connection. I have access to everything, but I cant login successfully into Cisco CP.
I set up a new user with level 15 privileges and a secret password. I go to login via webbrowser and I put in my credentials, but I get rejected. I have tested the username and password via the CLI, and it works fine, I just cant seam to login to Cisco CP.
I've got a 1941 router that keeps on rebooting by itself every minute. currently, there's no power issue.
I've detected the show version returned a bus error. Is this an IOS bug?
ROUTER uptime is 1 minute
System returned to ROM by bus error at PC 0x222FE2D4, address 0xD0D0D71 at 14:27:13 SGT Tue Nov 27 2012
[Code].....
I have a strange behavior and a simple proble . I configured the following static route
ip route 10.84.22.0 255.255.254.0 10.84.23.254
That I advertsied in eBGP :
router bgp 65000
network 10.84.22.0 mask 255.255.254.0
the IP next hop 10.84.23.254 is cascaded on my customer LAN . At nominal time the router advertsed the route in BGP
pjnb1376#sh ip bgp nei 57.213.169.169 ad
Next Hop Metric LocPrf Weight Path
*> 10.84.22.0/23 10.84.23.254 0 32768 i
When the lan interface of the router goes down , the router still advertise the route !!! Even if the IP next hop
10.84.23.254 is not reacheable anymore ....
The box is a Cisco 1941 using
1900-universalk9-mz.SPA.151-4.M1
I have a Cisco 1941 router configured using Cisco Configuration Professional... SSH management works from the LAN IP 10.0.1.254 and 10.0.2.254 Also, SSH management works from the LAN using the external domain name which resolves to the public IP address.
The problem i have is if I try SSH from the internet to the public IP.. nothing happens.
cisco1941#show config
Using 18498 out of 262136 bytes
!
! Last configuration change at 13:57:49 PCTime Tue Feb 14 2012 by admin
[Code].....
I bought a secondhand small business router (model 1941 Integrated Services Router) for personal use. It runs version IOS 15.0(1)M1 software, which seems to work well, but I'd like to download a firmware update that addresess some of the security flaws in this software. When I tried the download process it told me I need to buy a service contract first? Is this right, or am I doing something wrong?
View 1 Replies View RelatedI’m looking for some specific parameters of Cisco 1941 and not able to find them .
1. Maximum number of DHCP clients2. Maximum number of DHCP pools3. Maximum number of V LANs on trunk port.
Recently my company buy a EHWIC4ESG card and put into the cisco 1941. The reason we buy this card is because the in built two network ports of cisco 1941 are being used up. g0/1 is being connected to the internet and g0/0 is being connected to the office switch (192.168.5.x)
We have two servers (192.168.6.x and 158.55.33.x) that required to be connected to this router 1941 where the router will be configured as VPN for external user to access this server.
The EHWIC4ESG card is put into the router 1941 and after typing the "running-config" command, i could see it create a vlan 1 interface and
interface GigabitEthernet0/1/0
interface GigabitEthernet0/1/1
interface GigabitEthernet0/1/2
interface GigabitEthernet0/1/3
[Code]...
I have a new cisco 1941 router that I am setting up with pxe-booting. I have never setup pxebooting before and i have this setup so far ip dhcp pool Admin
-option 66 ip 192.168.1.4
-option 67 ascii pxelinux.0
and i can pull an ip but it keeps getting hung up when it comes to the TFTP part.
I decided recently to switch out our border router (1841 12.4 advsecurity) with a shiny new 1941 (15.2 SEC/K9) as the CPU upgrade was needed.The core below acts as a VPN end point to various other remote offices we have, all of which have a similar network design at each end (and all entirely managed by me). All of these are still running 1841's with 12.4 advsecurity on them as well. These are all GRE tunnels with ipsec procection on them (not crypto maps). [code]
Everything else works fine (NAT, route-maps etc), it's just these IPSEC/isakmp tunnels that are not playing ballIt's definitely not an ARP issue (all arps were cleared) and ICMP appears to work fine (ie, I can ping the remote tunnel's public IP endpoint from the core using the loopback for that tunnel as the source). I am suspecting it's something strange with the stateful firewall config, but I did try and apply ipsec and isakmp-msft to the ip inspect list, with no success.