I have a new cisco 1941 router that I am setting up with pxe-booting. I have never setup pxebooting before and i have this setup so far ip dhcp pool Admin
-option 66 ip 192.168.1.4
-option 67 ascii pxelinux.0
and i can pull an ip but it keeps getting hung up when it comes to the TFTP part.
im having trouble setting up a vpn for a 1941 router this is what I have setup
crypto isakmp policy 10
encr aes 256
authentication pre-share
crypto isakmp key ########## address 63.247.48.50
[code]....
my whole problem comes about when i need to Nat 192.168.1.0 to 10.12.14.0/24 before it goes through the tunnel.
Yesterday a coleagu accdently removed the CF card from the router now the router does no longer want to boot completely. It extracts the image from the CF card but when it has to initialize the configuration it stucks there for hours. Can it be that the startup config is somehow corrupted?
When i try to tftpdnld is says that the mac address is illegal.
The first line of the cookie looks like 04 ff 08 86 ff ff ff ff ff ff ff ff ff ff ff ff
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)Technical Support: [URL], Inc.PLD version 0x10GIO ASIC version 0x127c2801 platform with 196608 Kbytes of main
[Code]......
i facing problem with my switch cisco 3560G, when it power on only System light is green and noting happen. i check with serial cable ( Console) but noting happen no booting.
View 2 Replies View RelatedI have a 6500 that keeps booting into Rommon, even though it has a valid image file on the sup-bootdisk, and the config register is 0x2102. When it reloads I see this on the screen: [code] It seems like the repeating error is "error - on read during ELF program load". I can boot the system off of a CF card, but I'd like to use the sup-bootdisk.
View 11 Replies View RelatedYesterday I've faced a Problem that is not letting me boot with the new IOS.
Actually I'm planning upgrade IOS which supports SSH. As part of plan I've downloaded the new IOS image and uploaded via TFTP server to the switch.
After uploading to the switch. I've verified image and MD5 hash also. Everthing is fine. Then after I set the boot variable for the newly uploaded Image.
When I'm rebooting the Device it is not taking the new IOS. It's booting with the OLD image. Even It's not showing any error message while rebooting (ACTIVITY FILE ATTACHED FOR YOUR REFERENCE) I can't take risk by deleting the old IOS.
I tried to upgrade the IOS on my internal AP and now I am in a reboot cycle. I have tried to manually boot the old and new IOS images from the rommon but neither are working. here is the output I am getting:
ap: dir flash:
Directory of flash:/
2 -rwx 6563840 <date> ap801-k9w7-tar.124-21a.JY.tar
4 drwx 256 <date> ap801-k9w7-mx.124-21a.JA1
152 -rwx 548 <date> env_vars
153 -rwx 2775 <date> cpconfig-ap801.cfg
154 -rwx 2775 <date> back_up.txt
155 -rwx 3763 <date> config.txt
[code]....
I'm having an issue with 2 of my 3560s which are not booting. The last thing I did on both switches before it hangs was:
>write erase
>reload
restarted as normal
[Code]....
I've tried powering-off the switch and pressing the Mode button and power on. I got to swtch: mode switch:reset
It restarted past the POST but just hang halfway at the same bootp-up process as shown on the attached. The SYST LED is Green color when it hangs.
I bought a CISCO SG200-18 switch. I added the Switch to my LAN and started the Switch (as described in the manual). The Switch starts the booting procedure (green blinking status LED) After a while, the LED starts to blink orange and green, instead of steady green.
In generally the Switch seems to work. I can access my whole network, but not the web interface of the switch itself. I also can't see the switch in the ADSL / DHCP rooter.
I also tried to boot the switch only connected to the PC. But ping on 192.198.1.254 is not working. The switch is in the same subnet like my other LAN components.
Subnetzmaske . . . . . . . . . . : 255.255.255.0
Standardgateway . . . . . . . . . : 192.168.1.1
I exchanged the switch. But the new switch shows the same behavior.
An ASA 5505. Device boots to rommon #0> and stays there. The complete boot record follows:
CISCO SYSTEMS
Embedded BIOS Version 1.0(12)13 08/28/08 15:50:37.45
Low Memory: 632 KB
High Memory: 507 MB
[Code]....
I have a brand new 3650x switch that I was configuring via console and left it on overnight; this was friday night ( I forgot to keep the air conditioner on). When I returned Sunday afternoon and checked the switch I realized that the SYS and STAT lights on the front were not on, however the Leds on the PS module were still on. I powered it down and turn it on again but still there are no lights on the front. The PS OK and AC OK leds on the PS module are on but I noticed the leds on the two fan modules are not green or even amber; they are off.When I first turned on the switch I remembered distinctly that there were loud noice and if all fans were in overdrive mode for a few seconds then the went to normal. I'm not gettgin this loud noise phenomenom.
View 9 Replies View Relatedi am facing time daely issues on cisco 2960 s series switch while booting .It is taking time for electing masrer and sleeve for stacking.can i disable the election process for stcking while booting.
View 4 Replies View RelatedOne of the 6500 was going in bootrom mode, so I have formated the flash disk using the other Cisco 6500 switch and copied IOS file to the boot disk. But the 6500 booting failed.
View 6 Replies View Relatedtoday I received a Cisco 1841 Router with a problem i have never seen before. Maybe this my 1st really,really broken Cisco Router. When I power the Router on, the fan and all lights turn on (green) and that's it. Nothing changes, also after minutes of wating. On console i don't get any messages and I already tried every BAUD rate possible. Switched the router off/on again and again. And no, it's obviously not a console problem of my computer, because i tried with different routers.
View 3 Replies View RelatedI have a 4507R with a WS-X4515 supervisor V. It was booting into rommon mode, so I attempted to boot to an IOS image from TFTP. The boot process hangs at at the end of the below output and the then the status light blinks orange. I left it sit like this overnight, and it remained the same.
rommon 23 >boot tftp://x.x.x.x/cat4500-entservicesk9-mz.122-53.SG2.bin
Tftp Session details are ....
Filename : /cat4500-entservicesk9-mz.122-53.SG2.bin
[Code]......
One of my customer had a problem with A/C and the room temperature reached almost 50 C. We came to the site and saved the configuration, took a backup and shutdown the switch.
After the A/C problem is resolved, we tried to power-on the switch .. and we found that it is going to the rommon.
I put "boot" command to boot from the bootdisk, but I am getting the following error:
Code...
I tried to search it, But it is resulting in that most probably it is a hardware failure on the SUP.
I have 2950 switch booting through MOnitor Mode.Analyzed there is no Cisco IOS image in flash.
View 1 Replies View RelatedI have a Catalyst 4506e that works fine but if reload, it boots in rommon mode. I can start it with a boot command, but by default, i must type a command. My config-register is 0x2102.
View 5 Replies View RelatedI have a cisco 7606-S with dual RSP720-3CXL. Devices reloaded and now none of the RSPs are booting.When I have tried to take the console using only one RSP, card going to rommon mode after that it hangs. I guess its firmware is corrupted.
View 4 Replies View RelatedI have a 1941 router configured for Policy based routing with two ISPs.Two static default routes configured to point the gateways of respoective ISPs with same metric.But the problem is, packets are going throug the one ISP only while doing traceroute.
N/W connectivity:
ISP1-----> <----------------------> LAN1
| Router |
ISP-------> <----------------------> LAN 2
Below is my configuration :
Current configuration : 5958 bytes
!
! Last configuration change at 05:18:56 UTC Mon Jun 25 2012
!
version 15.0
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
I have this Cisco 1941 router with two Ethernet ports g0/0 and g0/1. The g0/0 is connected to office LAN with internet access. As my office LAN is DHCP, it will assigned a IP address for g0/0 since this g0/0 is configured as "ip address dhcp". Now my question is that i have a group of 5 pcs, namely PC1, PC2, PC3, PC4 and PC5 that is connected to the switch and one of the ports of this switch is connected to g0/1 of Cisco 1941. Is it possible that let say PC2 and PC3 (both DHCP enabled) could access the internet access from g0/0 and at the same time, the office LAN assigned IP address for PC2 and PC3 automatically?
Office Lan with internet access (DHCP) (Default gateway 10.0.0.1)
|
|
g0/0 (DHCP enable) (DHCP assigned IP address 10.0.0.138)
Cisco router 1941
g0/1
|
|
HP Switch
|
PC1 PC2 PC3 PC4 PC5
Is this operation possible? if possible, how to configure inside the router 1941 to achieve this objective?
I have just set up my Cisco 1941 router to my cable internet connection. I have access to everything, but I cant login successfully into Cisco CP.
I set up a new user with level 15 privileges and a secret password. I go to login via webbrowser and I put in my credentials, but I get rejected. I have tested the username and password via the CLI, and it works fine, I just cant seam to login to Cisco CP.
I've got a 1941 router that keeps on rebooting by itself every minute. currently, there's no power issue.
I've detected the show version returned a bus error. Is this an IOS bug?
ROUTER uptime is 1 minute
System returned to ROM by bus error at PC 0x222FE2D4, address 0xD0D0D71 at 14:27:13 SGT Tue Nov 27 2012
[Code].....
I have a strange behavior and a simple proble . I configured the following static route
ip route 10.84.22.0 255.255.254.0 10.84.23.254
That I advertsied in eBGP :
router bgp 65000
network 10.84.22.0 mask 255.255.254.0
the IP next hop 10.84.23.254 is cascaded on my customer LAN . At nominal time the router advertsed the route in BGP
pjnb1376#sh ip bgp nei 57.213.169.169 ad
Next Hop Metric LocPrf Weight Path
*> 10.84.22.0/23 10.84.23.254 0 32768 i
When the lan interface of the router goes down , the router still advertise the route !!! Even if the IP next hop
10.84.23.254 is not reacheable anymore ....
The box is a Cisco 1941 using
1900-universalk9-mz.SPA.151-4.M1
I am having an issue accessing the internet from a PC on the LAN. I have configured the PC with the gateway of the router infront of the ISP to test. I can ping from the router to google or any other internet IP. From the PC I can ping to the GIG0/1 (Inside LAN IP) and the GIG0/0 (Outside WAN IP going to ISP) but I can't ping the Next Hop IP of the ISP or anything past that. If I do a trace route from the PC to the google IP address it hits the GIG0/1 Inside LAN IP Address but fails from there. Here is a cut down snap shot of the router configure
[code]....
I have a Cisco 1941 router configured using Cisco Configuration Professional... SSH management works from the LAN IP 10.0.1.254 and 10.0.2.254 Also, SSH management works from the LAN using the external domain name which resolves to the public IP address.
The problem i have is if I try SSH from the internet to the public IP.. nothing happens.
cisco1941#show config
Using 18498 out of 262136 bytes
!
! Last configuration change at 13:57:49 PCTime Tue Feb 14 2012 by admin
[Code].....
I bought a secondhand small business router (model 1941 Integrated Services Router) for personal use. It runs version IOS 15.0(1)M1 software, which seems to work well, but I'd like to download a firmware update that addresess some of the security flaws in this software. When I tried the download process it told me I need to buy a service contract first? Is this right, or am I doing something wrong?
View 1 Replies View RelatedI did have a router cisco 1941 but can not do ipsec with it,i did take a smart net.
View 3 Replies View RelatedI’m looking for some specific parameters of Cisco 1941 and not able to find them .
1. Maximum number of DHCP clients2. Maximum number of DHCP pools3. Maximum number of V LANs on trunk port.
Recently my company buy a EHWIC4ESG card and put into the cisco 1941. The reason we buy this card is because the in built two network ports of cisco 1941 are being used up. g0/1 is being connected to the internet and g0/0 is being connected to the office switch (192.168.5.x)
We have two servers (192.168.6.x and 158.55.33.x) that required to be connected to this router 1941 where the router will be configured as VPN for external user to access this server.
The EHWIC4ESG card is put into the router 1941 and after typing the "running-config" command, i could see it create a vlan 1 interface and
interface GigabitEthernet0/1/0
interface GigabitEthernet0/1/1
interface GigabitEthernet0/1/2
interface GigabitEthernet0/1/3
[Code]...
I have a 1941W that has a connection to my ISP (Gi0/1) and another connection to a remote lab (Gi0/0). Everything is working fine how it is setup. All my traffic from my internal networks can access the Internet and devices on the 192.168.201.0 /24 can access the Internet and the lab 10.89.0.0/16.
Now I want to have two devices (192.168.201.51 & .147) use Gi0/0 when accessing host 63.85.190.67. There is no route to this subnet since it reside in the remote lab. Here is what I have right now. How would I setup a PBR to have those two host use Gi0/0 when accessing 63.85.190.67
interface Vlan192
ip address 192.168.201.1 255.255.255.0
ip nat inside
ip virtual-reassembly (code)
I have a Cisco router 1941 connected to a switch. I'm configuring the w LAN- AP and i need to have the wireless devices have an ip in the same range of the wired devices.Since i cant use the same ip range on the gig0/1 and the V LAN 1 for the wireless, i wanted to know how to config the giga0/1 connected to the switch to act as a layer 2 port and i keep the ip on the v LAN 1.
View 9 Replies View RelatedI have a 1941 integrated services router that will not keep the configs. After several atempts of saving running config to the startup config, then rebooting the device. I am having to reload the configs manually from TFTP because they are gone. I have also tryed the "wr" command to see. Is there a proper way to shutdown this particular type of router?
View 2 Replies View Related