One of the 6500 was going in bootrom mode, so I have formated the flash disk using the other Cisco 6500 switch and copied IOS file to the boot disk. But the 6500 booting failed.
View 6 RepliesI have a 6500 that keeps booting into Rommon, even though it has a valid image file on the sup-bootdisk, and the config register is 0x2102. When it reloads I see this on the screen: [code] It seems like the repeating error is "error - on read during ELF program load". I can boot the system off of a CF card, but I'd like to use the sup-bootdisk.
View 11 Replies View RelatedOne of my customer had a problem with A/C and the room temperature reached almost 50 C. We came to the site and saved the configuration, took a backup and shutdown the switch.
After the A/C problem is resolved, we tried to power-on the switch .. and we found that it is going to the rommon.
I put "boot" command to boot from the bootdisk, but I am getting the following error:
Code...
I tried to search it, But it is resulting in that most probably it is a hardware failure on the SUP.
document which explians normal booting sequence in a 6500 Switch running IOS. What I am looking for is in which order the image is loaded in SUP, RP, SP etc
View 1 Replies View Relateddirect me to a document detailing the order that line cards are supposed to boot in a 6500? I'm noticing random boot sequences in some of my chassis,?Note: We currently run Sup720 3CXL for the most part.
View 6 Replies View RelatedI have purchased a new hard disk, but my DVD ROM is dead. i have one another system. How can i boot the new hard disk from network..?
View 1 Replies View Relatedi recently bought a new Supervisor Engine 720 WS-SUP720-3B and 48-port 10/100/1000 RJ45 EtherModule WS-X6148A-GE-45AF. Once i fired it all up i got this error %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 2, power not allowed: Unknown Card Type. the System image file is "bootdisk:s72033-ipservicesk9_wan-mz.122-18.SXE6a.bin".
I have a 6509 up and running the same mods and working fine BUT the System image file is sup-bootdisk:s72033-ipservicesk9-mz.122-18.SXF7.bin. Is the boot image what is causing my isses?
I have a cisco1841 router with 32M CF card installed.Now , i want boot a system image larger 32M from usbdisk.First i insert the 128M usb flash disk to the 1841 router and format it, then i can see the device from dir command.Second copy the larger ios image from tftp to the usb disk and successed,i can see the image with " dir usbflash0:" command.Third i use this command "boot system " ,but there is no selection of "usbflash0: " Does the cisco 1841 router boot the system image from usb disk when reboot the router.
View 2 Replies View Relatedhow can we upgrade 6500 non modular ios to normal 6500 ios?
View 5 Replies View RelatedYesterday a coleagu accdently removed the CF card from the router now the router does no longer want to boot completely. It extracts the image from the CF card but when it has to initialize the configuration it stucks there for hours. Can it be that the startup config is somehow corrupted?
When i try to tftpdnld is says that the mac address is illegal.
The first line of the cookie looks like 04 ff 08 86 ff ff ff ff ff ff ff ff ff ff ff ff
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)Technical Support: [URL], Inc.PLD version 0x10GIO ASIC version 0x127c2801 platform with 196608 Kbytes of main
[Code]......
i facing problem with my switch cisco 3560G, when it power on only System light is green and noting happen. i check with serial cable ( Console) but noting happen no booting.
View 2 Replies View RelatedYesterday I've faced a Problem that is not letting me boot with the new IOS.
Actually I'm planning upgrade IOS which supports SSH. As part of plan I've downloaded the new IOS image and uploaded via TFTP server to the switch.
After uploading to the switch. I've verified image and MD5 hash also. Everthing is fine. Then after I set the boot variable for the newly uploaded Image.
When I'm rebooting the Device it is not taking the new IOS. It's booting with the OLD image. Even It's not showing any error message while rebooting (ACTIVITY FILE ATTACHED FOR YOUR REFERENCE) I can't take risk by deleting the old IOS.
I tried to upgrade the IOS on my internal AP and now I am in a reboot cycle. I have tried to manually boot the old and new IOS images from the rommon but neither are working. here is the output I am getting:
ap: dir flash:
Directory of flash:/
2 -rwx 6563840 <date> ap801-k9w7-tar.124-21a.JY.tar
4 drwx 256 <date> ap801-k9w7-mx.124-21a.JA1
152 -rwx 548 <date> env_vars
153 -rwx 2775 <date> cpconfig-ap801.cfg
154 -rwx 2775 <date> back_up.txt
155 -rwx 3763 <date> config.txt
[code]....
I'm having an issue with 2 of my 3560s which are not booting. The last thing I did on both switches before it hangs was:
>write erase
>reload
restarted as normal
[Code]....
I've tried powering-off the switch and pressing the Mode button and power on. I got to swtch: mode switch:reset
It restarted past the POST but just hang halfway at the same bootp-up process as shown on the attached. The SYST LED is Green color when it hangs.
I bought a CISCO SG200-18 switch. I added the Switch to my LAN and started the Switch (as described in the manual). The Switch starts the booting procedure (green blinking status LED) After a while, the LED starts to blink orange and green, instead of steady green.
In generally the Switch seems to work. I can access my whole network, but not the web interface of the switch itself. I also can't see the switch in the ADSL / DHCP rooter.
I also tried to boot the switch only connected to the PC. But ping on 192.198.1.254 is not working. The switch is in the same subnet like my other LAN components.
Subnetzmaske . . . . . . . . . . : 255.255.255.0
Standardgateway . . . . . . . . . : 192.168.1.1
I exchanged the switch. But the new switch shows the same behavior.
I have a new cisco 1941 router that I am setting up with pxe-booting. I have never setup pxebooting before and i have this setup so far ip dhcp pool Admin
-option 66 ip 192.168.1.4
-option 67 ascii pxelinux.0
and i can pull an ip but it keeps getting hung up when it comes to the TFTP part.
An ASA 5505. Device boots to rommon #0> and stays there. The complete boot record follows:
CISCO SYSTEMS
Embedded BIOS Version 1.0(12)13 08/28/08 15:50:37.45
Low Memory: 632 KB
High Memory: 507 MB
[Code]....
I have a brand new 3650x switch that I was configuring via console and left it on overnight; this was friday night ( I forgot to keep the air conditioner on). When I returned Sunday afternoon and checked the switch I realized that the SYS and STAT lights on the front were not on, however the Leds on the PS module were still on. I powered it down and turn it on again but still there are no lights on the front. The PS OK and AC OK leds on the PS module are on but I noticed the leds on the two fan modules are not green or even amber; they are off.When I first turned on the switch I remembered distinctly that there were loud noice and if all fans were in overdrive mode for a few seconds then the went to normal. I'm not gettgin this loud noise phenomenom.
View 9 Replies View Relatedi am facing time daely issues on cisco 2960 s series switch while booting .It is taking time for electing masrer and sleeve for stacking.can i disable the election process for stcking while booting.
View 4 Replies View Relatedtoday I received a Cisco 1841 Router with a problem i have never seen before. Maybe this my 1st really,really broken Cisco Router. When I power the Router on, the fan and all lights turn on (green) and that's it. Nothing changes, also after minutes of wating. On console i don't get any messages and I already tried every BAUD rate possible. Switched the router off/on again and again. And no, it's obviously not a console problem of my computer, because i tried with different routers.
View 3 Replies View RelatedI have a 4507R with a WS-X4515 supervisor V. It was booting into rommon mode, so I attempted to boot to an IOS image from TFTP. The boot process hangs at at the end of the below output and the then the status light blinks orange. I left it sit like this overnight, and it remained the same.
rommon 23 >boot tftp://x.x.x.x/cat4500-entservicesk9-mz.122-53.SG2.bin
Tftp Session details are ....
Filename : /cat4500-entservicesk9-mz.122-53.SG2.bin
[Code]......
I have 2950 switch booting through MOnitor Mode.Analyzed there is no Cisco IOS image in flash.
View 1 Replies View RelatedI have a Catalyst 4506e that works fine but if reload, it boots in rommon mode. I can start it with a boot command, but by default, i must type a command. My config-register is 0x2102.
View 5 Replies View RelatedI have a cisco 7606-S with dual RSP720-3CXL. Devices reloaded and now none of the RSPs are booting.When I have tried to take the console using only one RSP, card going to rommon mode after that it hangs. I guess its firmware is corrupted.
View 4 Replies View RelatedWe have got a big problem with our NAM (WS-SVC-NAM-1) - it does not boot. We have got a second one and in an other chassis. I changed the chassis, and RAM and Flash from the other one. RAM and Flash are ok.
We checked the disc (hardware) with an Ontrack-tool -it is OK.
environment: 6500 VSS
sh logging:
Jun 17 13:18:24: SW1_SP: Switch 1 Physical Slot 7 - Module Type LINE_CARD inserted
sm(cygnus_oir_bay slot7), running yes, state wait_til_online
Last transition recorded: (offline)-> empty (remove)-> empty_clr_persist (remove)-> empty (insert)-> may_be_occupied (timer)-> occupied (known)-> can_power_on (yes_power)-> powered_on (real_power_on)-> check_power_on (timer)-> check_power_on (power_on_ok)-> wait_til_online
As long as I have been doing this stuff, I have never had a clear understanding of all of the 6500 boot images and statements. The more I read online, the more I get confused.
1. What is the boot image "boot-mz" for? Where should it be placed (i.e. bootflash)? what command do I need to issue in order to use the boot image I want?
2. What is the IOS rommon image for? I thought the rommon image was the boot image but apparently these are two different images. Where should it be placed (i.e. bootflash, sup-bootflash, etc). What command do I use to ensure that I am using this IOS rommon image?
On cisco and am having some issues with intervlan routing. I have followed the vids and manuals but just can seem to get this working. I have the following network lab set up.
Vlan 10 = 10.70.1.9/24
Vlan 20 = 192.168.0.1/24
ME2400 firmware
ROM: Bootstrap program is ME340x boot loader
BOOTLDR: ME340x Boot Loader (ME340x-HBOOT-M) Version 12.2(35r)SE3, RELEASE SOFTWARE (fc1)
[Code]...
The network gods recently updated our 6500 and upon reboot, the FWSM booted to CF:1 maintence partition,which caused an immediate outage. On the router, I ran the following command to set the default FWSM boot partition to the configuration with:Router#boot device module 4 cf:5 However, it appears the "show boot device" command has been replaced with "show bootvar" which doesn't show me which partition the router will boot the FWSM to. Is there a command I can run from the Router that will actually confirm the boot partition for the FWSM if the router reloads.
View 1 Replies View RelatedI unpacked a new 3560x and went to put our standard code version on it c3560e-ipbasek9-mz.122-53.SE2. Everything seemed to upgraded fine but it won't boot to a console prompt. It seems like it loads the IOS image fine but can't get passed the Front-end Microcode IMG MGR: Programming device 0. [code]
View 4 Replies View RelatedI cannot boot IOS, when i reload this switch it go to ROMMON. I try to uploand IOS but it still has problem. i think i may wrong some point during i did uploand.
This is problem
Switch#sh bootvar
BOOT variable = cat4500-entservicesk9-mz.150-2.SG3.bin,1;bootflash:cat4500-entservicesk9-mz.150-2.SG3.bin,1;bootflash:cat4500-entservicesk9-
[Code].....
I tried to upgrade IOS from SXI2a to SXI9 in cat 6506 VSS. But the problem is that switch always boot with old IOS. I put the new IOS in sup-bootdisk and slave sup-bootdisk, bootvar is ok with new IOS: [code] Show bootvar is ok but switch always boot with old IOS SXI2a, some bug in IOS sxi2a???, I will try to delete de old IOS from sup bootdisk and try with the new one only.
View 5 Replies View Relatedmy Catalyst 3750 switch. Following a power cut the switch no longer boots up. The SYST light flashed green but no POST checks are made. I cannot see any boot messages from the console port either. The switch was on a UPS but some thing may have damaged the switch.
View 7 Replies View RelatedWhat would happen if I installed a 32MB (MEM870-32F=) flash upgrade card in to a Cisco 871 router that already had 28MB flash on-board already? Would the router boot seeing 52MB (the max this router can have) or would it fail completely since the combined total would be over 52MB?
I know you can get a 24MB upgrade card but they are quite expensive.