I have a cisco 7606-S with dual RSP720-3CXL. Devices reloaded and now none of the RSPs are booting.When I have tried to take the console using only one RSP, card going to rommon mode after that it hangs. I guess its firmware is corrupted.
View 4 Replies
I have a 7606-S router ( non redundant ) with SUP32 and i wand to replace it with RSP720-3C-GE , i am asking about the procedure?
-shall i switch off the router ? or just removeSUP32 and insert RSP720 ?
-are there any steps should i do before the upgrade ?
-i am planning to take the router out of service during the operation, how much down time it will be ?
I tried to reboot manually and I changed the slot but the same behavior:
%SYS-SP-3-LOGGER_FLUSHING: Systema pausing to ensure console debugging output
%OIR-SP-6-CONSOLE: Changin console ownership to route processor
*** System received a Software forced crash ***
signal= 0x17, code= 0x24, context= 0x430213e4
PC = 0x4038c124, Cause = 0x1020, Status Reg = 0x34008102
I have two Cisco 7606 routers using BGP to connect our customers to the internet. Recently we added a new 1G circuit in addition to an existing 1G circuit and all traffic inbound is now on this new 1G circuit. We would like to shift some of the inbound traffic over to the other 7606. Our Tier provider has the same AS number for both paths. One path goes directly to New York and the other goes to Boston then New York.
View 1 Replies View RelatedI have made an etherchannel between 6509 and 7606 with two giga interfaces on eatch one to have more bandwidth (2Go), but the Etherchannel does not exceed 1 GB (Below is a capture for Etherchannel taken from Solarwinds).the both 6506 and 7606 use ws sup 720 3bxl
View 8 Replies View RelatedI have a Cisco 7606 running 12.2. I want to limit the interface that is used by one of our customers to 30M.
View 3 Replies View Relatedits a hardware problem or just not get power to module 1 for module WS-X6748-GE-TX? this is the capture from show module and sh log :
------------------ show module ------------------
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX xxx
5 2 Route Switch Processor 720 (Active) RSP720-3CXL-GE xxx
Mod MAC addresses Hw Fw Sw Status
[code].....
Our router suddenly reloaded. Below are the crashinfo obtained:
1st crashinfo:
7606_Router#more sup-bootflash:crashinfo_20120604-02260500:00:05: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
00:00:05: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
00:00:05: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
00:00:05: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
[code]....
We are running s72033-advipservicesk9_wan-mz.122-18.SXF9
following errors.
Nov 7 21:34:50: %EARL_NETFLOW-SP-STDBY-4-TCAM_THRLD: Netflow TCAM threshold exceeded, TCAM Utilization [99%]
Nov 7 21:44:44: %EARL_NETFLOW-SP-4-TCAM_THRLD: Netflow TCAM threshold exceeded, TCAM Utilization [91%]
I've already found this kinds of cases, in this community. So, It seems that Changing the current configuration to 'mls aging fast threshold ## time ## ' is most suitable in our situation.But, I don't know how to calculate the apt threshold value and time value.
[1] sh run | in mls
mls ip multicast flow-stat-timer 9
mls flow ip interface-full
no mls flow ipv6
no mls acl tcam share-global
mls cef error action freeze
[code]....
I have my router 7606-S rebooted by itself. According to output of show version command it's rebooted by software bug.
================ Snipped from crashinfo file =================
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-2-MBE: Multiple bit error detected at 0xC09F4D38
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-3-SYNDROME_MBE: 8-bit Syndrome for the detected Multi-bit error: 0x0
05:33:50 GMT+7 Sat Jan 14 2012: Unexpected exception to CPU: vector 1500, PC = 0xB7922BC , LR = 0xB792250
==================== Show Version ======================
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 10-Feb-11 19:27 by prod_rel_team
ROM: System Bootstrap, Version 12.2(33r)SRD5, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
[Code]...
I have one Cisco 7606 and i need to install a WS-X6748-GE-TX with WS-F6700-DFC3CXL.When I install the WS-X6748-GE-TX the module is powered off with the following warning:
00:01:45: %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 1, power not allowed: Unsupported baseboard/earl combination. [code]
I faced with problem while i was attemping to upgrade CISCO7606 (R7000) from 12.2(33)SRE1 to 12.2(33)SRE6.
rommon 2 > boot c7600s72033-advipservices-mz.122-33.SRE6.bin
Loading image, please wait ...
Invalid device specified
Booting from default device
Initializing ATA monitor library...
string is bootdisk:c7600s72033-advipservices-mz.122-33.SRE1.bin
[code].....
Yesterday a coleagu accdently removed the CF card from the router now the router does no longer want to boot completely. It extracts the image from the CF card but when it has to initialize the configuration it stucks there for hours. Can it be that the startup config is somehow corrupted?
When i try to tftpdnld is says that the mac address is illegal.
The first line of the cookie looks like 04 ff 08 86 ff ff ff ff ff ff ff ff ff ff ff ff
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)Technical Support: [URL], Inc.PLD version 0x10GIO ASIC version 0x127c2801 platform with 196608 Kbytes of main
[Code]......
i facing problem with my switch cisco 3560G, when it power on only System light is green and noting happen. i check with serial cable ( Console) but noting happen no booting.
View 2 Replies View RelatedI have a 6500 that keeps booting into Rommon, even though it has a valid image file on the sup-bootdisk, and the config register is 0x2102. When it reloads I see this on the screen: [code] It seems like the repeating error is "error - on read during ELF program load". I can boot the system off of a CF card, but I'd like to use the sup-bootdisk.
View 11 Replies View RelatedYesterday I've faced a Problem that is not letting me boot with the new IOS.
Actually I'm planning upgrade IOS which supports SSH. As part of plan I've downloaded the new IOS image and uploaded via TFTP server to the switch.
After uploading to the switch. I've verified image and MD5 hash also. Everthing is fine. Then after I set the boot variable for the newly uploaded Image.
When I'm rebooting the Device it is not taking the new IOS. It's booting with the OLD image. Even It's not showing any error message while rebooting (ACTIVITY FILE ATTACHED FOR YOUR REFERENCE) I can't take risk by deleting the old IOS.
I tried to upgrade the IOS on my internal AP and now I am in a reboot cycle. I have tried to manually boot the old and new IOS images from the rommon but neither are working. here is the output I am getting:
ap: dir flash:
Directory of flash:/
2 -rwx 6563840 <date> ap801-k9w7-tar.124-21a.JY.tar
4 drwx 256 <date> ap801-k9w7-mx.124-21a.JA1
152 -rwx 548 <date> env_vars
153 -rwx 2775 <date> cpconfig-ap801.cfg
154 -rwx 2775 <date> back_up.txt
155 -rwx 3763 <date> config.txt
[code]....
I'm having an issue with 2 of my 3560s which are not booting. The last thing I did on both switches before it hangs was:
>write erase
>reload
restarted as normal
[Code]....
I've tried powering-off the switch and pressing the Mode button and power on. I got to swtch: mode switch:reset
It restarted past the POST but just hang halfway at the same bootp-up process as shown on the attached. The SYST LED is Green color when it hangs.
I bought a CISCO SG200-18 switch. I added the Switch to my LAN and started the Switch (as described in the manual). The Switch starts the booting procedure (green blinking status LED) After a while, the LED starts to blink orange and green, instead of steady green.
In generally the Switch seems to work. I can access my whole network, but not the web interface of the switch itself. I also can't see the switch in the ADSL / DHCP rooter.
I also tried to boot the switch only connected to the PC. But ping on 192.198.1.254 is not working. The switch is in the same subnet like my other LAN components.
Subnetzmaske . . . . . . . . . . : 255.255.255.0
Standardgateway . . . . . . . . . : 192.168.1.1
I exchanged the switch. But the new switch shows the same behavior.
I have a new cisco 1941 router that I am setting up with pxe-booting. I have never setup pxebooting before and i have this setup so far ip dhcp pool Admin
-option 66 ip 192.168.1.4
-option 67 ascii pxelinux.0
and i can pull an ip but it keeps getting hung up when it comes to the TFTP part.
An ASA 5505. Device boots to rommon #0> and stays there. The complete boot record follows:
CISCO SYSTEMS
Embedded BIOS Version 1.0(12)13 08/28/08 15:50:37.45
Low Memory: 632 KB
High Memory: 507 MB
[Code]....
I am having difficulties with getting SPAN traffic over my WS-X6704-10GE (CFC).
CISCO7606
ios 12.2(33)SRE6, SUP720-3BXL
Trying to use the span feature, put the commands listed below in and they entered successfully, but the port is not being mirrored.
interface TenGigabitEthernet1/1
description PUBLIC
dampening
mtu 9216
ip address x.x.x.x x.x.x.x
[Code]....
I have a brand new 3650x switch that I was configuring via console and left it on overnight; this was friday night ( I forgot to keep the air conditioner on). When I returned Sunday afternoon and checked the switch I realized that the SYS and STAT lights on the front were not on, however the Leds on the PS module were still on. I powered it down and turn it on again but still there are no lights on the front. The PS OK and AC OK leds on the PS module are on but I noticed the leds on the two fan modules are not green or even amber; they are off.When I first turned on the switch I remembered distinctly that there were loud noice and if all fans were in overdrive mode for a few seconds then the went to normal. I'm not gettgin this loud noise phenomenom.
View 9 Replies View Relatedi am facing time daely issues on cisco 2960 s series switch while booting .It is taking time for electing masrer and sleeve for stacking.can i disable the election process for stcking while booting.
View 4 Replies View RelatedOne of the 6500 was going in bootrom mode, so I have formated the flash disk using the other Cisco 6500 switch and copied IOS file to the boot disk. But the 6500 booting failed.
View 6 Replies View Relatedtoday I received a Cisco 1841 Router with a problem i have never seen before. Maybe this my 1st really,really broken Cisco Router. When I power the Router on, the fan and all lights turn on (green) and that's it. Nothing changes, also after minutes of wating. On console i don't get any messages and I already tried every BAUD rate possible. Switched the router off/on again and again. And no, it's obviously not a console problem of my computer, because i tried with different routers.
View 3 Replies View RelatedI have a 4507R with a WS-X4515 supervisor V. It was booting into rommon mode, so I attempted to boot to an IOS image from TFTP. The boot process hangs at at the end of the below output and the then the status light blinks orange. I left it sit like this overnight, and it remained the same.
rommon 23 >boot tftp://x.x.x.x/cat4500-entservicesk9-mz.122-53.SG2.bin
Tftp Session details are ....
Filename : /cat4500-entservicesk9-mz.122-53.SG2.bin
[Code]......
One of my customer had a problem with A/C and the room temperature reached almost 50 C. We came to the site and saved the configuration, took a backup and shutdown the switch.
After the A/C problem is resolved, we tried to power-on the switch .. and we found that it is going to the rommon.
I put "boot" command to boot from the bootdisk, but I am getting the following error:
Code...
I tried to search it, But it is resulting in that most probably it is a hardware failure on the SUP.
I have 2950 switch booting through MOnitor Mode.Analyzed there is no Cisco IOS image in flash.
View 1 Replies View RelatedI have a Catalyst 4506e that works fine but if reload, it boots in rommon mode. I can start it with a boot command, but by default, i must type a command. My config-register is 0x2102.
View 5 Replies View Related I have Cisco router 7606-S. On Sami module led is indicate red. i also test it to other slot,reload the chassis but the problem is same. The module status is unnkown.
(Indicates red one of the following conditions:
• The SAMI is released from reset by the supervisor engine and is booting.
• The boot code failed to run.)
pdsn1#sh mod
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 7 SAMI Module WS-SVC-SAMI-BB-K9 SAL15056HSV
2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL14480S9Q
5 2 Route Switch Processor 720 (Active) RSP720-3C-GE SAL1538QE8N
6 2 Route Switch Processor 720 (Hot) RSP720-3C-GE SAL1538QHZB
[code]....
1.is this a hardware problem of sami module?
2. is this a boot problem of sami module? is this image problem of modules(supervisor or sami module)?
how i do diagnostics this module?
I have a problem accessing my wireless router through VLAN sub-interface on my Cisco 1841 router. My hardware:
Cisco Catalyst 2960 switch (192.168.100.4 /24)
Cisco Catalyst 3550 switch (192.168.100.6 /24)
Cisco 1841 router (192.168.100.7 /24)
Asus RT N66U wireless router (192.168.100.2 /24)
Here's my network topology:
I have two VLANs - 10 and 20. 2 DHCP pools are configured on 2 1841's interfaces - 192.168.1.0 /25 and 192.168.1.128/26 with default router sitting on 192.168.1.1 and 192.168.1.129 respectively. No issues with obtaining IP address from any of those pools.Laptop connects to L3 3550 switch (switchport access vlan 10), which, in turn, connects to 1841 router through trunk (with VLANs 10 and 20 allowed).3550 is connected to 2960 through trunk with VLANs 10 and 20 allowed.Wireless router is connected to 2960.I can successfully ping my wireless router and outside world from 1841 from fa0/1 interface, but not from fa0/1.10 or fa0/1.20 sub-interfaces - all packets got dropped. My laptop can obtain IP from both pools (depending on port I connect it to), but can't ping my wireless router and anything beyond it.
I attach my configs:Cisco Catalyst 3550:interface FastEthernet0/1 switchport trunk encapsulation dot1q switchport mode trunk switchport port-security mac-address sticky speed 100!interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk!interface FastEthernet0/3 switchport access vlan 10 switchport mode access!interface FastEthernet0/4 switchport access vlan 20 switchport mode access!Cisco 1841:
ip dhcp pool Vlan10DHCP network 192.168.1.0 255.255.255.128 default-router 192.168.1.1 dns-server 208.67.220.220 domain-name home.local
!ip dhcp pool Vlan20DHCP network 192.168.1.128 255.255.255.192 default-router 192.168.1.129 dns-server 208.67.220.220 lease 0 12
interface FastEthernet0/1 ip address 192.168.100.7 255.255.255.0 duplex auto speed auto!interface FastEthernet0/1.10 description VLAN10 Sub Interface encapsulation dot1Q 10 ip address 192.168.1.1 255.255.255.128!interface FastEthernet0/1.20 description VLAN20 Sub Interface encapsulation dot1Q 20 ip address 192.168.1.129 255.255.255.192!
Routing table on 1841:
[code]....
I dont understadn how this works but basically I have enabled dhcp or so I thought bu clients dont get a lease. The vlan does but clients connecting to the switchports attached to the vlan do not get a lease and cant connect to anything. If I static the ip or use my server to issue dhcp then it's fine still some issues since I am cluceless but I dont understand what I have to do to get dhcp to work on the fa0-3 ports.
Router#sh running-config
Building configuration...
Current configuration : 1015 bytes
!
[Code]......
