Cisco Switching/Routing :: 1841 / Routing Through Sub-interfaces Fails?
May 31, 2013
I have a problem accessing my wireless router through VLAN sub-interface on my Cisco 1841 router. My hardware:
Cisco Catalyst 2960 switch (192.168.100.4 /24)
Cisco Catalyst 3550 switch (192.168.100.6 /24)
Cisco 1841 router (192.168.100.7 /24)
Asus RT N66U wireless router (192.168.100.2 /24)
Here's my network topology:
I have two VLANs - 10 and 20. 2 DHCP pools are configured on 2 1841's interfaces - 192.168.1.0 /25 and 192.168.1.128/26 with default router sitting on 192.168.1.1 and 192.168.1.129 respectively. No issues with obtaining IP address from any of those pools.Laptop connects to L3 3550 switch (switchport access vlan 10), which, in turn, connects to 1841 router through trunk (with VLANs 10 and 20 allowed).3550 is connected to 2960 through trunk with VLANs 10 and 20 allowed.Wireless router is connected to 2960.I can successfully ping my wireless router and outside world from 1841 from fa0/1 interface, but not from fa0/1.10 or fa0/1.20 sub-interfaces - all packets got dropped. My laptop can obtain IP from both pools (depending on port I connect it to), but can't ping my wireless router and anything beyond it.
I attach my configs:Cisco Catalyst 3550:interface FastEthernet0/1 switchport trunk encapsulation dot1q switchport mode trunk switchport port-security mac-address sticky speed 100!interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk!interface FastEthernet0/3 switchport access vlan 10 switchport mode access!interface FastEthernet0/4 switchport access vlan 20 switchport mode access!Cisco 1841:
ip dhcp pool Vlan10DHCP network 192.168.1.0 255.255.255.128 default-router 192.168.1.1 dns-server 208.67.220.220 domain-name home.local
!ip dhcp pool Vlan20DHCP network 192.168.1.128 255.255.255.192 default-router 192.168.1.129 dns-server 208.67.220.220 lease 0 12
interface FastEthernet0/1 ip address 192.168.100.7 255.255.255.0 duplex auto speed auto!interface FastEthernet0/1.10 description VLAN10 Sub Interface encapsulation dot1Q 10 ip address 192.168.1.1 255.255.255.128!interface FastEthernet0/1.20 description VLAN20 Sub Interface encapsulation dot1Q 20 ip address 192.168.1.129 255.255.255.192!
Routing table on 1841:
[code]....
View 19 Replies
ADVERTISEMENT
Sep 27, 2012
Looking for multicast over IRB interfaces. My full config below, works as expected on a Cisco 1760 router (IOS 12-4) but fails strangely on our Cisco 2800 (IOS 15-1) and Cisco 1941 G2 routers.
I use Windows 7 Enterprise and VLC 2.0.0 Two Flower as the multicast video receiver. On the 1760 router, I open VLC, request the video (rtp://@239.255.0.1:5004) and it plays flawlessly.
We have to upgrade the older outdated unsupported Cisco 1760 routers. We replace the Cisco 1760 router with a Cisco 1941 router. Configuration differs ONLY in the interface speeds; F0/0 to G0/0 and that is just bout it. Using the same Windows 7 Enterprise PC, I open VLC again and request the video -same as before; No video and no voice. We swap the 1941 out and put in the 1760 again, multicast works flawlessly. If we put the 1941 router back in, multicast fails again. We put the Cisco 2800 series router in and it also fails the same as the 1941 router.
Troubleshooting, I open VLC and request the same multicast video. On the same PC, I open Wireshark and start capturing packets, - and instantly the VLC video starts playing. I close Wireshark and the video stops. I open Wireshark and start capturing packets again and the VLC video starts playing again.
Wireshark shows the video packets are being received from the source when VLC is requesting the video. If I close VLC while Wireshark is capturing packets, Wireshark shows the video stream stops.
Shows the correct multicast sources, incoming and outgoing interface details
Incoming interface is Serial
Outgoing interface is BVI
Show ip pim rp
Reveals the correct RP details
[code]...
View 2 Replies
View Related
Feb 6, 2012
I'm just getting started with cisco kit so you will have to bare with me.I have a cisco 1841.i have a very wierd issue of routing...i cannot ping and browse through this.
View 3 Replies
View Related
Mar 13, 2013
I dont understadn how this works but basically I have enabled dhcp or so I thought bu clients dont get a lease. The vlan does but clients connecting to the switchports attached to the vlan do not get a lease and cant connect to anything. If I static the ip or use my server to issue dhcp then it's fine still some issues since I am cluceless but I dont understand what I have to do to get dhcp to work on the fa0-3 ports.
Router#sh running-config
Building configuration...
Current configuration : 1015 bytes
!
[Code]......
View 2 Replies
View Related
Dec 12, 2011
I have VLans 20 and 21 set by ISP for Voice and Data respectively.What will happen if I already have VLans 20 and 21 in my Local network?
View 4 Replies
View Related
Feb 3, 2010
We've been mocking up a test lab to test VSS on two 6500's. Each 6500 has one sup720 and a 6708-10ge blade and we've established the two 10ge links between the two chassis; the first from the each chassis' sup and the second from each 6708.My question is, what happens when the supervisor fails on one of the chassis?
View 10 Replies
View Related
Aug 30, 2012
Just checking if any switch reset after one PS failure (configured in default redundant mode). No crash file has been generated. Switch is running IOS 12.2(44)SG and PWR-C45-1400AC. After the switch went online we found that PS1 has gone bad. Haven't found any bug in the tool kit. [code]
View 5 Replies
View Related
Jun 14, 2012
i have a cisco catalyst 2960g and for some reason out of the blue, some interfaces go down and then up. It started doing it after a power cycle.
View 1 Replies
View Related
Nov 15, 2011
I have a 2911 router. One interface is configured external (WAN) and two interfaces are configured on separate internal private subnets. What is the configuration to allow all traffic in both directions between the two internal subnets?
View 21 Replies
View Related
Jan 9, 2013
I am using an Old 3500XL and I simply created a
interface VLAN 100
Description ***********
ip address 10.0.1.100 255.255.255.248
no ip directed-broadcast
no ip route-cache
shutdown
no matter what I do i cannot get it to come up, the rest of the switch is default config, I know I am just forgetting something, But I don't know what?
View 8 Replies
View Related
Jan 9, 2012
today I witnessed a cisco n5k that stopped playing fair. For a yet unkown reason several interfaces started to show output errors all begining within the same second. While i instantly thought this would be a wiring issue I began to ask myself what an output error actually means. Google usually brings up output drops, not regular output errors. So what is it and how can a 10G fiber interface even detect that there is a problem without receiving what it was sending?
View 2 Replies
View Related
Nov 18, 2012
in my simple network setup, I cannot resolve DNS queries from inside my NATted network. On the router I can ping both IP-addresses and names. Ping from the local machine works for IP-Adresses but not for names. When doing nslookup, addresses are not found and a SERVFAIL message is returned. I use a Cisco ISR 861 Router to connect our local LAN to the Internet (The WAN of the 861 is connected to another DHCP/NAT-Router, which in turn connects to the ISP-Modem). Addresses in the local LAN are DHCP-distributed, the DNS-Servers from my ISP are configured on the Router and the DNS-Information is distributed correctly to my local LAN machines (as I can verify by doing nslookup on Linux).
View 21 Replies
View Related
Mar 26, 2009
our backbone (6509) is connected to atm backbone (nortel passport) those are connected through giga Ethernet interface and running ospf in area 0. One week ago we lost the ip connectivity between those backbones, the interfaces were in up but the neighbor relation fail and it was kept in LOADING STATE, according we the logs the neighbor relation fail because a BAD LSA was received (error messages %OSPF-4-ERRRCV:Bad LSU adv and %OSPF-4-BADLSATYPE:Invalid lsa:Bad LSA chksum Type 5 were received during the outage)We check in cisco and this is quite normal behavior if we receive a bad LSA but the customer is asking why we have the same error message for long time and we didn't lost the neighbor relationship.
how many bad lsa we can receive before to lost the neighbor relationship.We receive two errors messages for bag lsa.. [code]
View 3 Replies
View Related
Jun 11, 2012
I am currently trying to setup a GRE tunnel on a cisco 861. As part of a configuration template provide by an outside source I am recommended to use a sub-interface on the router but the recommended configuration does not work.
View 1 Replies
View Related
Sep 2, 2012
I am trying to connect a 6509 switch to a 4503-E switch using single mode dark fiber over a distance of less than half a mile. Although a routine task, it does not work..We have a care 6509 switch where we concentrate all of our dark fiber connections for our remote sites. The 6509 switch already has 30 remote sites, most of them with 4503-E switches, connected in this way therefore it is a tested scenario. For the connections we use the GLC-LH-SM SFPs on both switches. Out of these 30 sites we had a similar problem with two of them, which we solved with the use of CWDM SFPs. With the CWDMs the fiber came up right away. However, I cannot keep using this solution because it is way too expensive! I had the losses of the fiber measured end-to-end and they are negligible (>0.5 dB).
In this latest case, like I said, we could not bring the connection up between the core 6509 switch and the 4503-E switch using the GLC-LH-SM SFPs. I then replaced the 4503-E switch with a 3560 and the link came up! Then I tried using a CWDM-SFP in the 4503-E, while keeping the GLC-LH-SM SFP in the 6509 and the link came alive again! Of course we already tried replacing the fiber patch cords with no luck. [code] I find it very weird for the link to work with the 3560 or with a CWDM in the 4503 but NOT with the SFP in the 4503!
View 6 Replies
View Related
Jan 10, 2013
I have a Nexus 5548UP that would be managed by two organizations. Is it possible to set IP addresses for mgmt0 and an SVI (or an L3 interface) without using the L3 daughter card? I don't want to route between VLANs, just to separate management traffic.
View 4 Replies
View Related
May 3, 2012
I just upgraded all of our switches on campus to Version 15.0(2)SG4 after about a month of testing. On two switches so far, we are seeing that clients can not connect, and the switch isnt detecting a link. I dont see anything out of the ordinary in int status, port-security, or errors on the interface. Plugging in a different computer does nothing. Only thing that works, is a shut, no shut of the interface. After that, its connected.
View 7 Replies
View Related
Feb 10, 2013
I'm working on my CCNA. I purchased an old router 2610 with two ethernet ports. I configured the IP addresses on the interfaces and added the default gateway. I configured NAT to go out my ATT DSL router to the internet. With the 2610, I'm able to ping the back end or internal DSL router, but I can't ping the front end, external router, or out to any internet site such as google.
View 10 Replies
View Related
Jul 12, 2012
We did an upgrade from NX-OS 5.1.5 to 5.2.4 and found all M1 line card interfaces were stuck in initializing state for long time.'show module' status says ok. And we cannot execute shut/no shut command under the interface. N7K-M108X2-12L & N7K-M148GT-11 are the two M series cards. Only option was to downgrade back for the time being.
N7K01# sh int e1/1 | in down
Ethernet1/1 is down (initializing)
View 3 Replies
View Related
Jun 6, 2013
I have two switches (sanitized configs attached) and I am trying to bond int gi0/1 and gi0/2 between the two. Then I need int gi0/3 back to the main LAN switches. These are new Vlans created 982 and 983 for these switches. Question #1: do the configurations look correct? I haven't placed any laptops on the interfaces to test interconnectivity yet but I am wondering if it will work with no default routes.
The admin team needs these switches at location A for setup then they will be moved to Location B. The only thing that sucks for me is that the network admin before me created gateway interfaces for all the local Vlans on a main router as sub interfaces. For example, for these two subnets, I need to create subinterfaces below (at location A), which is why a gave the Vlan on the switches, ip addresses.
interface GigabitEthernet0/0.982
encapsulation dot1Q 982
ip address 10.98.2.1 255.255.255.0
ip flow ingress
no cdp enable
service-policy input mark-mplsqos-in
interface GigabitEthernet0/0.983
encapsulation dot1Q 983
ip address 10.98.3.1 255.255.255.0
ip flow ingress
no cdp enable
service-policy input mark-mplsqos-in
When I move the subnet to location B, I will also move the gateway. These two switches will be used mainly for a VMWare and HyperVisor environment so Vlan 982 is for VMA network and Vlan 983 is for management. The admin tells me the software needs to tag the packets, I am not sure if I care as the switches should handle that also.
View 1 Replies
View Related
May 23, 2013
Is the onboard interfaces on an ASR router (4x on ASAR1002, 6x on ASR1002-X) are fixed gigabit or are they 10/100/1000 ?
I assume the interfaces on the 8port Gigabit SPA module are fixed gigabit speed ports (why otherwise sell a 10/100 8port SPA module also ?) no ?
View 2 Replies
View Related
Aug 13, 2012
I need to bridge 2 subinterfaces; F0/0.301 and F0/0.302 on a single router.The router interfaces with a Cisco 2960 (LAYER-2) switch.QUESTION is, does a Cisco router support bridging on subinterfaces on the same physical interface?Currently this is NOT operational Spaiing-tree on F0/0.301 and F0/0.302 is down, switch side is forwarding for both Vlans.show ip interface brief shows up/down status of F0/0.301, F0/0.301 and BVI6 is down/down?
:
SETUP:
bridge irb
!
!
Interface F0/0
no ip address
[code]....
View 1 Replies
View Related
Jul 17, 2012
I have a Catalyst 4500 L3 Switch Software (cat4500e UNIVERSAL-M), Version 03.02.00.XO RELEASE SOFTWARE (fc2). So I just wanted to verify that the switch only does dot1q encapsulation because the switchport trunk encapsulation dot1q command does not work.
View 3 Replies
View Related
Jan 21, 2012
I am having issues with 'telnet' on port 2821 to a range of servers connecting through vlan interface from my core switch 6513 running s72033_rp-DVIPSERVICESK9_WAN-VM) version 12.2(33)SXH7, RELEASE SOFTWARE (fc3). The telnet on port 1556 and 13724 is ok.
View 1 Replies
View Related
Jan 16, 2008
I have this card installed onmy 3845 running version 12.4(18). But this card fails to show up.
here is what I found in a show tech.
WIC Slot 0:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
Hardware Revision : 2.0
Top Assy. Part Number : 800-27738-02
Part Number : 73-10677-02
Board Revision : B0
Deviation Number : 0
Fab Version : 02
PCB Serial Number : FOC********
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-2FE
Version Identifier : V01
CLEI Code : COUIAFUCAA
Base MAC Address : 001a.6c70.260b
MAC Address block size : 2
Connector Type : 01
EEPROM format version 4
EEPROM contents (hex):(code)
View 4 Replies
View Related
Feb 28, 2012
I have a cisco 7606-S with dual RSP720-3CXL. Devices reloaded and now none of the RSPs are booting.When I have tried to take the console using only one RSP, card going to rommon mode after that it hangs. I guess its firmware is corrupted.
View 4 Replies
View Related
Jun 4, 2012
I use Nexus 7010 as our layer 3 router.I have ssh feature turned on so I can manage it from the management interface. I just found out that users can use putty to ssh to the local SVI interface of the NEXUS. Although they still need username and password to login but we dont want them even able to bring up the welcome screen.Example, user's IP is : 172.16.25.100 , they can ssh to 172.16.25.1 which is the NX SVI interface.
View 1 Replies
View Related
Sep 26, 2012
I would like to do the following architecture with the same C3750 : network X,Y,Z connected to 3750 in VRF D the 3750 uses a routed interface on subnet E for the default route in VRF D on this routed interface a BYPASS EQUIPMENT the other BYPASS EQUIPMENT interface is connected also to another routed interface on subnet E "also" this routed interface is in another VRF C with other network A and B.do you know if it will work because of 2 routed interfaces on the same IP subnet or is there a way to do that ? the only goal for me is to catch traffic from network X,Y,Z on SYN and ACK.
View 5 Replies
View Related
Dec 20, 2011
I remember I did that one time on 2800 router with Gi0/0 and Gi0/1 to connect another port channel in 3560G switch. I have no way to try it in ISR G2 router like 2900 or 3900 now. I know the the ethernet switch module must support it. I wonder if the integrated interfaces support it or not.
View 5 Replies
View Related
Apr 17, 2012
I've just started a CCNA course and my lack of knowledge has me a bit stuck. My network is comprised of Cisco components and I'm semi familiar with them just from reading and looking through options. I currently am using a Cisco ASA 5520 on my network and I am trying to join another network via one of the interfaces. My network is 192.168.0.0 255.255.0.0 and my inside interface is 192.168.1.1 255.255.0.0. I enabled a second interface using a static ip of 10.0.0.1 with a subnet of 255.255.255.128. Connected to that interface, I have a Fortigate firewall at 10.0.0.2 255.255.255.128. I can ping just fine from the Fortigate network to the 10.0.0.1 interface on the Cisco ASA 5520 network, but I can not ping the 10.0.0.1 interface (or anything past it) on the ASA 5520 from any computer on the Cisco network. I've read that ACL's and NAT have to be done as well as enabling traffic between interfaces with the same security levels. (both interfaces have security levels of 100 and the option is checked to allow traffic).
Note: each network has it's own internet connection. The connection is to share information on servers on both networks with each other.
View 1 Replies
View Related
Aug 16, 2012
I am trying to add WCCP to be configured for websense. My first option seems to be either purchase an IPServices license for the stack of 3750E switches, but i am thinking this will require us to license all three switches in the stack. The second option i am looking at is to do the WCCP configuration on the 2800 router we have on the edge. The problem is both Gig ports are in use, one going to the firewall and the second going to the ISP. My first question would be, which option is better in terms of manging as well as cost of implementing it.The second question is, if WCCP on the router is a better option, what is the add on module i should be looking to get to add the additional ports to hook up the Websense cache.
View 8 Replies
View Related
Oct 28, 2012
how I can check the qos counters and stats for interfaces on my cat 6509 ?
View 1 Replies
View Related
Apr 23, 2013
I have a client with a 3750x stack. We've upgraded it to IP Services. We have a simple PBR setup. One access-list to forward traffic from a specific LAN ip to another gateway on the network.
I go to vlan1 (default vlan) to apply the PBR and the command takes with no errors, but do a "show run" and it doesn't show up under the interface.
I go to vlan1 and apply a PBR that doesn't exist and the command takes with no errors, and is listed under the interface in the config
I can apply the PBR globally and appears to work, but we can't have it there based on other issues it creates.
config: (all tracks are up)
C3750_stack#show sdm prefer
The current template is "desktop routing" template.
[Code]....
View 8 Replies
View Related
