Cisco Switching/Routing :: Catalyst 2960g Interfaces Going Up And Down?
Jun 14, 2012i have a cisco catalyst 2960g and for some reason out of the blue, some interfaces go down and then up. It started doing it after a power cycle.
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Catalyst 2960G Vlan Configuration?
Oct 24, 2011I have got a catalyst cisco 2960G series switch and via this switch I want to creat serveral vlans. I am getting a dhcp IP from a router and I want to setup my own vlan networks.
I plugged in the Ethernet cable that came from the dhcp router to port 16 of the cisco switch and configured the ports 1,2 and 3 for vlan 1, 2 and 3
the dhcp router has given me this IP 192.168.10.158 defautl gateway is : 192.168.10.1
when I plug in a PC to port 1 or 2 of the cisco switch I still receiving the IP from range 192.168.10.* but not from the range that I configured for the vlan 1 or 2.
Below is my startup configuration:
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
[code].....
Cisco Switching/Routing :: WOL Configuration On L3 Catalyst 6500 And L2 2960G?
Dec 20, 2011I got problem with wake on LAN software.. The software unable to ON all pc's remotely if sitting under different vlan. Everything is ok if using the same vlan. Below are the network diagram & switch configuration.
Layer 3 switch Intervlan routing configuration
ip forward-protocol udp 7
!
interface Vlan4
description vlan Client-WOL
ip address 172.22.51.253 255.255.254.0
ip access-group Deny_HTTP_Vlan1 in
ip helper-address 172.20.1.246
[code].....
After configured all the switches with the above setting, the software still cannot wake all the pc's using LAN. Base on sniffing, i can't find UDP port usage by the software. Attached here with print screen from wireshark.
Cisco Switching/Routing :: Catalyst 2960G-24TC-L All GigabitEthernet Is Missing
Jul 24, 2012My Cisco Catalyst 2960G-24TC-L is broken.Yes,I think it's broken.
1.Always dispaly : “ !!! WARNING: The switch is not usable !!! ” “Unable to create l2trace server process, socket_open() failed”.
2.All GigabitEthernet is missing .
Switch(config)#interface ?
Async Async interface
Auto-Template Auto-Template interface
[Code].....
Cisco Switching/Routing :: Browser Access To Switch Fails (Catalyst 2960G)
Jul 4, 2012I am unable to access a series of switches connected together through a management vlan. I receive the message "The server xx.xx.xx.xx at level_15_access requires a username and password." Entering the username and password fails and the same username and password message returns. I am able to ssh into the switch with the username and password that fails trying to access the switch with the browser.
How can I check the username and password for access with the browser?
I am trying to monitor switch performance. Is there a good way to monitor switch performance with the command line interface?
Cisco Switching/Routing :: 2960G Stack To Another 2960G
Oct 23, 2011I have used all the ports on my 24 port 2960G and need to extend it with another 2960G. These switches do not have trunk ports so what is the best way to stack them and have all 5 vlans on both switches.Can I just use a port Channel trunk etherchannel ?
View 7 Replies View RelatedCisco :: Catalyst 2960G / Get SNMP Management Working Over IPv6?
Jul 20, 2011I recently picked up a Catalyst 2960G and am trying to get SNMP management working over IPv6. I have the IP Address set to the local link, and can successfully ping and telnet to the switch (so the network can get traffic to and from the switch). However, SNMP packets just seem to disappear. I am running WireShark on my machine, and I see the packets go out to the proper IP, but nothing comes back. When I check "sho ipv6 traffic", I can see where there are UDP packets that are received, but, again, none going out. Also, when I run "sho snmp", all of the packet counts are 0.
Here are some relavant snipets from my "sho run":
interface Vlan1
no ip address
no ip route-cache
ipv6 enable
[code]....
Cisco Switching/Routing :: 2960G No LANBase-Routing Feature?
Feb 3, 2013one of our switches (WS-C2960G-24TC-L). When I try to turn on the lanbase-routing feature using sdm prefer lanbase-routing, it gives me an error (Unknown command). I tried "sdm prefer ?", and lanbase-routing wasn't there (only qos, default and dual IPv4 & IPv6). The switch is running on image C2960-LANBASEK9-M version 12.2(50)SE5.We have another switch (WS-C2960S-24TS-L), running on image C2960S-UNIVERSALK9-M version 12.2(55)SE5, and I can enable lanbase-routing feature. If I upgrade the WS-C2960G-24TC-L to version 12.2(55)SE5, will it be able to do inter-vlan routing? Or is the switch itself totally limited to VLAN configuration only?
View 4 Replies View RelatedCisco Switching/Routing :: 2960G Don't Have A Backup To Configuration In PC
Dec 30, 2011I have 2960G that in rommon status.I need that the switch work in 0x2102 (regular mode).I don't have a backup to configutratuio in my PC.I do wr before the switch go to rommon (startup config).What to do in order to the switch will be in 0x2102 (regular mode) with the same configuration( before the switch go to rommon)?
View 1 Replies View RelatedCisco Switching/Routing :: Cannot Upgrade 2960G Switch
Jun 26, 2012I have a few 24-port Cisco 2960G Switches (model WS-C2960G-24TC-L) that I upgraded to IOS Release 15.0(1)SE2 using the web interface. I am now trying to upgrade those switches with the new release, 15.0(1)SE3, however I seem unable to do it, I have tried this on two switches so far, both have been upgraded to SE2 just a couple months ago or so, and both of them will not accept the SE3 upgrade, basically, I can select the tar file in the web browser and click "Upgrade" but when I do the status never changes from "Loading the tar file to the switch". I have tried multiple times from multiple computers using many different web browsers, including IE6 which is listed as supported. I have let it go for as long as 1.5 hours but to no avail.I also had a few idential switches here that had never been upgarded to SE2, I have had no problems loading SE3 onto them using the same method so it would seem that the tar file I have downloaded is valid.
View 5 Replies View RelatedCisco Switching/Routing :: 2960g / How To Enable Multicast To Work
Jun 7, 2012I have a 2960G that I keep on the bench as a work switch. I assigned an IP address to it. The techs have had trouble imaging workstations using GHOST. Do any config changes need to be made to enable multicast to work? Everything is in VLAN1 at this point and the GHOST server is also the DHCP server.
View 1 Replies View RelatedCisco Switching/Routing :: 2960G - Switch Clustering Benefits?
Jun 11, 2013I recently changed jobs and at the new location we are primarily running Catalyst 2960G series switches with the exception of one 3750. All of the switches are setup in a cluster with the 3750 being the cluster master. My question is what is the benefit of switch clustering? The entire network seems to be a bit over engineered for the our needs and I am hoping to scale it back a bit. For example, the the network was setup with VOIP QoS when there were no plans to even use VOIP. Also what procedures would I want to follow to disable the cluster to avoid any major outages? Assuming there is no real need for a cluster.
View 1 Replies View RelatedCisco Switching/Routing :: 2960G Core Switch For 400 Users
Jun 7, 2012I'm trying to decide what switch to use as a core for 500 users. I'm currently looking at either 2 x 3750X stacks or 2 x 4500s with dual SUPs and PSUs, both options will provide the number of switchports required without the need for additonal access layer swiches. Which switch option is best to go for here? All of our services will be located in our data centre which will be connected using 2 1000Mbps MPLS circuits. I wont need any advanced L3 features and we are not likley to scale over 450 users. Also is it ok to use the dual switch stacks or chassis to provide the collapsed core/access layer or is it best to have a dedicated core (using one of the above options with less switchports) and having a dedicated accesss layer using 2960Gs for example. Our structured cabling terminates in a single comms room so we wont need to distribute switches throughout the office.
View 3 Replies View RelatedCisco Switching/Routing :: IOS Installation For Switch 2960G 48TC-L?
Oct 23, 2012i had made a software upgarde on the switch 2960G series have no any passwords, when I fished the upgrade process after rebooting the device i found it need a UserPw to access device manager. i tried to use the default PW "cisco" but it dosen't work too.. after that i tried the password recovery process to rest the PW, but noway, but now i have addition problem, when i try the cmd orders "flash_init , load_helper , dir flash" to beginning the password recovery process it shows the following:
The system has been interrupted prior to initializing theflash filesystem. The following commands will initializethe flash filesystem, and finish loading the operatingsystem software:
flash_init boot
switch: flash_initInitializing Flash...flashfs[0]: 554 files, 19 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 32514048flashfs[0]: Bytes used: 15540224flashfs[0]: Bytes available: 16973824flashfs[0]: flashfs fsck took 10 seconds....done Initializing Flash.
switch: load_helperUnknown cmd: load_helper
switch: load_helperUnknown cmd: load_helper
switch: load_helperUnknown cmd: load_helper
[code]....
After that the problem updated
because I tried to install the IOS by Xmodem to reload the missing flash file.After finsh the TAR file loading and reboot the switch.......the LEDs of mode and Giga ports are lighted amber and not blinking, i tried many times to follow the steps to connect the switch by the emulator and consol cable by holding mode button and connecting the power cable at same time the device does not work, the switch now still not blinking, now i try to read and understand how can i remove the corrupted files and install a new IOS for this switch?What shall i do.
Cisco Switching/Routing :: IP Igmp Filter Command On 2960G?
Jun 21, 2012I am unable to configure an interface using the "ip igmp filter <profile #>" command on a 2960G running 12.2(58)SE2. The switch allows me to create a profile using the "ip igmp profile <profile #>" global configuration command. It also lets me enable filtering with the global "ip igmp filter" command (which I didn't see in the documentation). But, the command is not accepted when configuring an interface. "ip igmp ?" does not even show "filter" as a valid auto-complete when in configure interface mode, and the command is rejected if I try to enter it.
I verified the command worked on a much earlier version of IOS, so it must have broken somewhere along the line. I'm wary of moving up to 15.0(1)SE. Is that a major IOS change?
Cisco Switching/Routing :: 2960G Disable Srr-queue On Switch Port
Jun 20, 2012I have a Cisco 2960G switch and one of the ports was configured with srr-queue bandwidth limit 90 - I need to remove this bandwidth limiting from this interface. [code]
View 2 Replies View RelatedCisco Switching/Routing :: Forwarding IEEE 802.3 Raw Packets Through 2960G Switch
Dec 5, 2011I have a requirement to monitor downstream data feed from a remote site and feed it to multiple destination devices for recording. The source data will be fed into a port on a Cisco 2960G switch then, using the monitor function, be forwarded to multiple interfaces. This works fine for normal Etherent II traffic. We tried a test using a device that generates IEEE 802.3 Raw packets ('type' field is used as a 'length' field) but found that while the traffic appeared to be accepted by the input port with no errors it was not forwarded to the destination ports, even when using the monitor function. I did try the 'encapsulation replicate' feature with no luck. It does not forward these packets even if I set all the ports into a common VLAN and let the switch just perform a normal switch function (non monitor).
if it is possible to get the IEEE 802.3 raw packets to pass through the switch and if it is, how to or what I need to do to make it work?
Cisco Switching/Routing :: 2960G - High Total Output Drops?
Mar 27, 2012Our database server is connected on cisco swich 2960G gigabitEthernet 0/38.while showing the interface command the total output drops is a large value..Is there any issue with this value.I think this is one of the reason for slow access of the server.
cisco6#show interfaces gigabitEthernet 0/38
GigabitEthernet0/38 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 58bc.2746.45a6 (bia 58bc.2746.45a6)
[Code].....
Cisco Switching/Routing :: How To Configure 6506 Or 2960G To Process Multicast Traffic
Aug 8, 2012Multicasting. The configuration is I have a 6506 as my core switch receiving multicasts from an interface assigned to VLAN10. I have a monitor port setup with a PC running Observer which says multicasts are being received on the core switch. On a different interface on the core switch I have a 2960G switch connected to it and this interface is on VLAN 10. The 2960G switch has a workstation connected to it that needs to receive the multicasts. How do I configure the 6506 and/or the 2960G to process the multicast traffic?
View 0 Replies View RelatedCisco Switching/Routing :: 3560G / Establish The Redundant Network Like For The Edge 2960G?
Mar 25, 2013i have 2 no of 3560G in our core, now my requirement is to establish the redunent network like for the edge 2960G using stack or some other way ...
View 6 Replies View RelatedCisco Switching/Routing :: 2960G / 3650G - Non-broadcast Traffic Appearing Across VLAN
Jul 5, 2012We run a network of several 2960G and 3650G switches in a network with a number of VLANs. One one particular VLAN (let's call it VLAN 10) it appears that non-broadcast traffic (i.e. normal unicast traffic) is being copied to every port in VLAN 10 only on one switch . The traffic is not crossing trunk ports and does not appear on other switches that have ports in VLAN 10. We first spotted this by noticing that a UPS port had an unusual amount of activity on our port througput graphs:
This traffic at 4 am is not expected and this profile is repeated across all ports in VLAN 10 on this switch (a WS-C2960S-48TD-L stack running IOS 15.0(1)SE3)\iffed one port using local SPAN (the UPS port) and discovered that this traffic was not broadcast, which was running at a normal low rate at all times. The traffic appeared to be unicast traffic from other ports of the sort you might see on a hub. It was from various hosts that live on VLAN 10, most (not all) of the conversations had one end station homed on the 'problem' switch. There are about 800 non-broadcast packets per hour and this is a busy VLAN so it does not account for all the traffic on the VLAN.
Cisco Switching/Routing :: 2960G High Output Drops Only On Gigabit Switch
Feb 11, 2013I just got a Cisco 2960G 24-port gigabit switch so that our HP servers can have a Gigabit connection to the network. I moved 2 servers to it (HP Proliant DL380's) but they don't actually seem to be able to achieve even close to 1000Gbps. I ran same some LAN bandwidth tests and it was showing only around 200-300 Mbps between all of them. I also ran a network stress test utility, LAN Tornado, and it was showing packet loss as high as 60% when on gigabit, and only .07% when on 100Mbps.
-Both the NIC's and the switch ports are set to 1000/Full
-Currently using Cat5e cabling no more than 25Ft in length (I know Cat6 would be better but Cat5e is supposed to support Gigabit)
-All servers are on the same VLAN
Here are the port statistics when running just a stress test @ 10Mbps that had a 45% packet loss. What's odd though is when I set the servers and switches to 100Mbps, I get less than 1% packet loss.
GigabitEthernet1/0/16 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 203a.07ff.7e90 (bia 203a.07ff.7e90)
MTU 9000 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
[Code].....
Cisco Switching/Routing :: 2960g-24tc-l Internal Power Supply Pinout / Voltage Check
Feb 25, 2013I had a bad power surge yesterday that took out a 2960g switch and the APC UPS that it was connected too. when plugged in the fan comes on and the syst light stays amber and the rps, stat, duplex. and speed light stay lit and the port lights for ports 21-24 stay lit. plugging it into the console on boot I cant even see rommon, so i dont think its even booting. I would like to find a pinout and voltage guide for the connector comming off the power supply so I can check the voltages coming off the power supply to tell if it is a bad PSU or if it took out the main board.
View 2 Replies View RelatedCisco Switching/Routing :: Configuring COS On 2960G Switches With Non-Cisco Phones
Mar 1, 2012I have 7 POE switches that have ESI IP phones attached. I have two VLANS, 1 and 2. VLAN 2 is used for voice and is defined in each switch.The ESI IP phones connect to my POE switch ports and the pc attaches through the ESI IP phone.
I have had voice quality issue between floors in my building. Talking to others on my floor via the IP phone, there are no voice quality issues. [code]
Cisco Switching/Routing :: 2960G Configuring Ether-channel On Stack-wise Stack
Sep 24, 2012A site that i am responsible for has the following equipment installed:
2 x 3750G Switches configured as a stack using Stackwise - Collapsed Core/Distribution Layer
5 x 2960G Switches as Access Layer switches
WAN connections into the Core/Distribution Layer are all Gigabit Ethernet over Fibre.This is a dedicated CCTV Network with 50 Cameras all streaming video into the Core (decoders connected to access switches)Each 2960G has 2 links to the Core/Distribution 3750G Switches, 1 to each switch - Gigabit.I'm running rapid-pvst on all switches, so spanning tree is blocking one of the ports and effectively halving the 2 gig bandwidth. Next year our customer is going to add in a further 50 - 60 cameras.After monitoring the current loading on the ports in use, we have suggested to the customer that the 2 connections to each should be Ether-channeled together. [code]
First interface takes commands no problem, keep getting the message that etherchannel cannot be configured across different switches in a stack when i try to put the second interface commands on.
Cisco Switching/Routing :: 1841 / Routing Through Sub-interfaces Fails?
May 31, 2013I have a problem accessing my wireless router through VLAN sub-interface on my Cisco 1841 router. My hardware:
Cisco Catalyst 2960 switch (192.168.100.4 /24)
Cisco Catalyst 3550 switch (192.168.100.6 /24)
Cisco 1841 router (192.168.100.7 /24)
Asus RT N66U wireless router (192.168.100.2 /24)
Here's my network topology:
I have two VLANs - 10 and 20. 2 DHCP pools are configured on 2 1841's interfaces - 192.168.1.0 /25 and 192.168.1.128/26 with default router sitting on 192.168.1.1 and 192.168.1.129 respectively. No issues with obtaining IP address from any of those pools.Laptop connects to L3 3550 switch (switchport access vlan 10), which, in turn, connects to 1841 router through trunk (with VLANs 10 and 20 allowed).3550 is connected to 2960 through trunk with VLANs 10 and 20 allowed.Wireless router is connected to 2960.I can successfully ping my wireless router and outside world from 1841 from fa0/1 interface, but not from fa0/1.10 or fa0/1.20 sub-interfaces - all packets got dropped. My laptop can obtain IP from both pools (depending on port I connect it to), but can't ping my wireless router and anything beyond it.
I attach my configs:Cisco Catalyst 3550:interface FastEthernet0/1 switchport trunk encapsulation dot1q switchport mode trunk switchport port-security mac-address sticky speed 100!interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk!interface FastEthernet0/3 switchport access vlan 10 switchport mode access!interface FastEthernet0/4 switchport access vlan 20 switchport mode access!Cisco 1841:
ip dhcp pool Vlan10DHCP network 192.168.1.0 255.255.255.128 default-router 192.168.1.1 dns-server 208.67.220.220 domain-name home.local
!ip dhcp pool Vlan20DHCP network 192.168.1.128 255.255.255.192 default-router 192.168.1.129 dns-server 208.67.220.220 lease 0 12
interface FastEthernet0/1 ip address 192.168.100.7 255.255.255.0 duplex auto speed auto!interface FastEthernet0/1.10 description VLAN10 Sub Interface encapsulation dot1Q 10 ip address 192.168.1.1 255.255.255.128!interface FastEthernet0/1.20 description VLAN20 Sub Interface encapsulation dot1Q 20 ip address 192.168.1.129 255.255.255.192!
Routing table on 1841:
[code]....
Cisco Switching/Routing :: Same VLans 20 And 21 At WAN And LAN Interfaces
Dec 12, 2011I have VLans 20 and 21 set by ISP for Voice and Data respectively.What will happen if I already have VLans 20 and 21 in my Local network?
View 4 Replies View RelatedCisco Switching/Routing :: 2911 - Allow Traffic Between Two LAN Interfaces?
Nov 15, 2011I have a 2911 router. One interface is configured external (WAN) and two interfaces are configured on separate internal private subnets. What is the configuration to allow all traffic in both directions between the two internal subnets?
View 21 Replies View RelatedCisco Switching/Routing :: 3500XL / VLAN Interfaces Will Not Come Up
Jan 9, 2013I am using an Old 3500XL and I simply created a
interface VLAN 100
Description ***********
ip address 10.0.1.100 255.255.255.248
no ip directed-broadcast
no ip route-cache
shutdown
no matter what I do i cannot get it to come up, the rest of the switch is default config, I know I am just forgetting something, But I don't know what?
Cisco Switching/Routing :: Output Errors On N5k 10G Interfaces?
Jan 9, 2012today I witnessed a cisco n5k that stopped playing fair. For a yet unkown reason several interfaces started to show output errors all begining within the same second. While i instantly thought this would be a wiring issue I began to ask myself what an output error actually means. Google usually brings up output drops, not regular output errors. So what is it and how can a 10G fiber interface even detect that there is a problem without receiving what it was sending?
View 2 Replies View RelatedCisco Switching/Routing :: Sub Interfaces And Recommended Configuration Not Works On 861
Jun 11, 2012I am currently trying to setup a GRE tunnel on a cisco 861. As part of a configuration template provide by an outside source I am recommended to use a sub-interface on the router but the recommended configuration does not work.
View 1 Replies View RelatedCisco Switching/Routing :: 4503-E Cannot Bring SFP Fiber Interfaces Up
Sep 2, 2012I am trying to connect a 6509 switch to a 4503-E switch using single mode dark fiber over a distance of less than half a mile. Although a routine task, it does not work..We have a care 6509 switch where we concentrate all of our dark fiber connections for our remote sites. The 6509 switch already has 30 remote sites, most of them with 4503-E switches, connected in this way therefore it is a tested scenario. For the connections we use the GLC-LH-SM SFPs on both switches. Out of these 30 sites we had a similar problem with two of them, which we solved with the use of CWDM SFPs. With the CWDMs the fiber came up right away. However, I cannot keep using this solution because it is way too expensive! I had the losses of the fiber measured end-to-end and they are negligible (>0.5 dB).
In this latest case, like I said, we could not bring the connection up between the core 6509 switch and the 4503-E switch using the GLC-LH-SM SFPs. I then replaced the 4503-E switch with a 3560 and the link came up! Then I tried using a CWDM-SFP in the 4503-E, while keeping the GLC-LH-SM SFP in the 6509 and the link came alive again! Of course we already tried replacing the fiber patch cords with no luck. [code] I find it very weird for the link to work with the 3560 or with a CWDM in the 4503 but NOT with the SFP in the 4503!
Cisco Switching/Routing :: Nexus 5548UP / Two Management Interfaces For N5k
Jan 10, 2013I have a Nexus 5548UP that would be managed by two organizations. Is it possible to set IP addresses for mgmt0 and an SVI (or an L3 interface) without using the L3 daughter card? I don't want to route between VLANs, just to separate management traffic.
View 4 Replies View Related