Cisco Switching/Routing :: 3845 With HWIC-2FE / Card Fails To Show Up
Jan 16, 2008
I have this card installed onmy 3845 running version 12.4(18). But this card fails to show up.
here is what I found in a show tech.
WIC Slot 0:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
Hardware Revision : 2.0
Top Assy. Part Number : 800-27738-02
Part Number : 73-10677-02
Board Revision : B0
Deviation Number : 0
Fab Version : 02
PCB Serial Number : FOC********
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-2FE
Version Identifier : V01
CLEI Code : COUIAFUCAA
Base MAC Address : 001a.6c70.260b
MAC Address block size : 2
Connector Type : 01
EEPROM format version 4
EEPROM contents (hex):(code)
View 4 Replies
ADVERTISEMENT
Mar 25, 2012
I change only a chasis in a router 3845, but the "show version" command should be the same , except for the serial number and other parameter of time.. however, the number of serial interface change from 4 up to 2.The hardware module of 3845 are 3.
1.- VWIC E1/T1 with 2 port
2.- Fastethernet 36 port
3.- Supervisor engine with 2 Gigabit port
View 7 Replies
View Related
Nov 16, 2011
I have a 3845 router. Setup SSH Version 2generated rsa keys (1024)set login localtransport input ssh and telnet is enabled since I can't get ssh connection working When I connect using SSH, I get the following error. server refused authentication protocol.
View 21 Replies
View Related
Dec 4, 2011
What cable I need to connect two 2951 back to back through a HWIC-4T1/E1 card ?
View 1 Replies
View Related
Oct 3, 2009
I have cisco 3845 router with 4 HWIC-2FE card none of them is detected the message displayed is [code]
View 7 Replies
View Related
Jul 25, 2012
In our Environmet we have 3845 Edge Router Current Ios Version is Version 12.4(1a),(c3845-advipservicesk9-mz.124-1a.bin)As management got another fiber leased line(Single Mode) for which i have install SFP slot part number HWIC-1GE-SFP,after installation of HWIC-1GE-SFP in router the follwing slot is showing
GigabitEthernet0/1/0
%HWIC_1GE_SFP-6-SFP_IN: Interface GigabitEthernet0/1/0 1000BaseLX SFP has been inserted
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/1/0 xx.xx.xx.xx. YES manual up down
for testing purpose i tried the same procedure into the switch and its working fine where as in Router the link is not coming up ,
View 5 Replies
View Related
Dec 27, 2011
I have got 3845/3945, I would like to increase HWIC slot density for HWIC 4 PORT ISDN BRI S/T ports through the NM/NME/NMX slots, Is there any measns to do that?
View 2 Replies
View Related
Jun 18, 2011
I have a cisco 1760 with running VIC-2FXO (working fine). I'm now trying to replace that line with an ISDN line through a VIC2-2BRI.
View 4 Replies
View Related
Mar 13, 2013
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies
View Related
May 27, 2012
Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies
View Related
Mar 24, 2011
I have 3845 Router with HWIC-4ESW & I am trying to apply MQC on SVI interface but I keep getting configuration Error!-RTR(config-if)#service-policy output XYZ_WAN_QOS Configuration failed I believe that HWIC-4ESW is Layer 2 port & you can not apply Module Qos on SVI interface. I am exploring other option.
I have following link for 1 OR 2 Port Fast Ethernet port but not sure whether this will support what I am looking for.[URL] Aslo I have HWIC-1GE-SFP card on Same router where MQC works fine .interface GigabitEthernet0/1 description METRO-E duplex auto speed auto media-type rj45 service-policy output Metro-E?
View 1 Replies
View Related
Dec 6, 2012
I have a 3845 that will not let me ping to the internet from my PC.On interface g0/0 I have a connection to a internet connection (another router), using DHCP to get it's address (it gives g0/0 IP 192.168.0.3).On interface g0/1, I have a connection to my LAN (I assign the interface IP 10.10.1.1).
I can ping the router. The router can ping the internet, do DNS resolution, etc.I have ensured routing is enabled. The only route I have configured is a default static route: 0.0.0.0 0.0.0.0 192.168.0.1.Oddly, if I choose 0.0.0.0 0.0.0.0 g0/0, I cannot ping sites on the internet from the router.
I tried setting up ip nat inside for my LAN and ip nat outside for the WAN/internet uplink, but this did not work.
This was the issue, I missed finishing the NAT setup.I can make the router ping out all day, and have my PCs ping the router, but getting the connection between the two is not working.
View 2 Replies
View Related
Apr 9, 2013
When we install an HWIC-2FE card in slot 0 or slot 1 of a 3845, the interface fails to pass any ping packet greater in size than 449 bytes. It works fine up until that limit is reached, but then fails completely on a larger size packet. If we move to slot 3 or slot 4 on the 3845, the card works just fine! I have looked through the cisco official bug tracker for HWIC-2FE, but could not find a similar symptom listed. We're running advanced ip services 12.4(24)T7 code on the routers. Any software fix or if this is a platform problem with the 3800 series.
View 3 Replies
View Related
Dec 5, 2011
if the card HWIC-1SER is the equivalent card HWIC-1T for 1861 router?
View 3 Replies
View Related
Dec 18, 2012
I was looking an HWIC card for CISCO2901-SEC/K9. We have one internet connection (ADSL) current.Now we want to backup internet connection from cable service provider. I will implement IPSec on this HWIC.
What HWIC cards can I choose for this router?
View 6 Replies
View Related
Aug 19, 2012
I've been given an 1841 with a 3G HWIC card installed to test with. I need to set up some sort of VPN to our ASA, the problem is though these 3G cards get a random public IP, so what options do I have to create a VPN tunnel from this router to the ASA without the 1841 getting a static public IP?
View 3 Replies
View Related
May 19, 2011
I have a 2811 router runnning IOS 12.4(21) and have added an HWIC 1FE card to slot 2. But the card doesnot show up in the router and all the three lights on the HWIC card is steady green. I have gone through some cisco documentation and found that i have to upgrade the IOS.
I have few questions before doing the upgrade.
1. Which IOS version should I upgrade to?
2. Will this erase my exisitng running configuration ? I have VPN services, PPPoATM, PBR etc.. all running on this router at present.
3. Presently i have a 128 MB CF card on the router. Will this be enough or do i need to upgrade this card also? Can i choose an IOS which will fit into this card otherwise while keeping all existng features?
4. I want to use the HWIC card for the ISP's internet service through PPPoE. Will this be possible with the upgraded IOS ?
View 1 Replies
View Related
May 10, 2011
I am trying to connect HWIC-2FE Card to my Cisco 2811 Router. The router is unable to detect the card. I get the following error message:
' %GT96K_FEWAN-1-UNKNOWN_WIC: NM slot 0, wic card has an unknown id 53BPort Statistics for unclassified packets is not turned on.'
View 2 Replies
View Related
Feb 14, 2012
I have cisco 2611 + NM1E , and i want to trade in for a cisco 2911 security router + HWIC4 Card.Which type of HWIC card should i use in the cisco2911-sec/k9 router?
View 1 Replies
View Related
May 19, 2013
I'm having problems to ping through interface atm 0/0/0 which is releated to a card HWIC-2SHDSL . The router I have is a 1941. I dont know what to do. [code]
View 8 Replies
View Related
Sep 2, 2011
How Can I connect two router with one HWIC-4ESW card , I have Problem with this because when I tried to do , I received the message I can´t configure IP address on L2. The idea is to connect two routers with /30.
View 2 Replies
View Related
May 31, 2011
I'm looking for a HWIC card that will support SC fiber connections for a 2811. I know of the HWIC-1GE-SFP but this one only support the LC connections.
View 2 Replies
View Related
Dec 28, 2011
I have a 2811 ISR, a lab unit with almost nothing yet configured other than some IP networks on serial and FE interfaces to ping to other lab routers. And I have one HWIC-4ESW installed, and I amrunning IOS 15.2.I want to set the card as a single routable interface and just have the ports act like switch ports, which I imagine is the default design of these cardsI work a lot with Cisco 891 ISRs so figured it's the same here, assign an IP to interface Vlan1 and all is well. That was wrong, obviously more config is required.It seems there are a lot of differing answers out there, so far none what worked for me. The best looking one I could find said to assign an IP to the Vlan 1 interface, then go to each of the four FE interfaces on the switch module.
View 3 Replies
View Related
Oct 31, 2010
[URL]The Cisco 2811 does not support the HWIC-4T1/E1 module. But, I installed HWIC-4T1/E1 on the 2811 running 124-24.T2.
View 3 Replies
View Related
Jan 24, 2013
Just double-confirm that 2811 is compatible with HWIC-2FE based on your experience? Which IOS is compatible with HWIC-2FE? [URL]
View 3 Replies
View Related
Jan 23, 2011
I have some issue on Card Hwic-D-9ESW with Router 2821, i was install card 9ESW in to router 2821 on slot 2 and 3. After I show run, the Cisco Router 2821 have interface F0/3/0 - F0/3/8.and i configure V lan already and interface up also.
When i connect PC to port F0/3/0, the interface is up, but i cannot pint go interface, i mean it request time out. My question is, Is it correct that i install card into slot 2 and 3?
What is the problem all port up but i cannot ping to interface?
Note: the same V lan
View 2 Replies
View Related
Dec 12, 2011
I am trying to configure a shdsl port on a 2911 router for CO mode of operation.The dsl-group auto command does not seem to change the port to operate in CO mode and the link will not come up to a remote router that has a card installed operating in CPE mode.The configuration I have applied for the shdsl controller is.
controller SHDSL 0/1/0
dsl-group auto
!
!
Do I need to use a HWIC-4SHDSL card for the CO mode operation?
View 3 Replies
View Related
Oct 17, 2012
Just need to verify if HWIC-2T is compatible with the Cisco2800 routers?
View 4 Replies
View Related
Nov 4, 2012
Maybe this was listed in the release notes for the product and I missed it, but can this item support Etherchannel in a 2801 router? I installed the module into the router and the router recognizes the module. I can configure the ports as access or trunk ports, but I am unable to configure the channel-protocol or the channel-group for the Etherchannel. The IOS on the router is 15.1 M with the upgraded Bootloader version 12.3.
View 1 Replies
View Related
Oct 15, 2012
I Have installed HWIC-2T card in my cisco 1921 router but it is not able to detected in router. find the ver of router
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL] Copyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Tue 20-Mar-12
[Code]......
View 8 Replies
View Related
Jul 31, 2012
I have cisco2811 and HWIC-1CE1T1-PRI in the main office are using to connect 10 branches ( 10 ISDN lines) for Data.
I have available channels in the used E1 so I can use them for voice using PVDM2-64 ?
View 3 Replies
View Related
Feb 27, 2012
We have been facing a problem at my company ! We have a Cisco Router 1921 with one HWIC-4ESW in trunking with a RuggedCom switch RSG2100.When I use the GigabitEthernet port to make a trunk, I create 2 sub-interfaces (one for each Vlan) and configure the Port on Switch as Trunk, the inter-VLan routing works with no problem.But now I need to use this configuration using the HWIC-4ESW on Router, and I can't do this work. I try creat interface Vlan for each vlan, and try creating the VLans at Router Vlans database, but no way. At router I enter in interface and try to do the switchport trunk command to add a Vlan, but doesn't work.
View 4 Replies
View Related
Jan 9, 2012
Does Cisco 1921-SEC/K9 support HWIC-4ESW ? I require 4 x 10/100 Ethernet ports
If yes how many ? are there any drawbacks if i use this module instead of a switch?
View 5 Replies
View Related
