Cisco Switching/Routing :: 3750 - Show Interface Vlan (ID) Doesn't Show In / Out Traffic Rate
Mar 13, 2013
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies
ADVERTISEMENT
Apr 26, 2013
I am working with 3750 switch.I console the switch and turn it on and it doesn’t show text in hyper terminal with any BAUD (I tried all the speeds). The hyper terminal works with other switches so the problem is not with the hyper terminal.when I tried to break the password it stuck after I was writing "flash_init" and when I entered or typed text it show only garbage characters. I tried to break the password with all the speeds and it shows garbage output. I tried to turn on the switch and hold control + break and it showed the text only with the speed 115200, but after I left holding and tried to type it showed only garbage again. Also I tried to copy text from the notepad to the hyper terminal.
View 6 Replies
View Related
Jan 16, 2012
I'm troubleshooting a 3750 switch stack problem where computers are showing input and CRC errors. I'd like to be able to execute a "show interface" command that will show me only the line showing the switch port and the line showing the input errors, but so far I can't figure out a way of combining those two parameters.
If I do "show interface | include Ethernet[0-9]�" I get all the lines showing the port numbers:
GigabitEthernet1/0/1 is up, line protocol is up (connected)
GigabitEthernet1/0/2 is up, line protocol is up (connected)
GigabitEthernet1/0/3 is up, line protocol is up (connected)
[Code].....
View 9 Replies
View Related
Mar 5, 2013
I have a really weired thing happening on 6509 device with one of my customers.The device has a SUP 2 (MSFC2) with version 12.2.18SXF17B.
any VLAN interface once administratively down or simply down shows on "show interface status" output as VLAN.While it supposed to show "Routed". However once the port is up it is shows "routed" like it should.
View 5 Replies
View Related
May 27, 2012
Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies
View Related
Aug 30, 2010
i've got a Cisco 877 router connected to an ADSL link. i'm using the show dsl interface atm just to have a look on its performance. i've tried to search on Cisco website on how to interpret the output but a blog gave me more info [URL]. My question now is, what readings do i consider? is it on the left (ATU-R) or on the right (ATU-C)?
877ROUTER#sh dsl int atm0 ATU-R (DS) ATU-C (US)Modem Status: Showtime (DMTDSL_SHOWTIME)DSL Mode: ITU G.992.1 (G.DMT)ITU STD NUM: 0x01 0x01Vendor ID: 'ALCB' 'ALCB'Vendor Specific: 0x0000 0x0000Vendor Country: 0x00 0x0FCapacity Used: 31% 85%Noise Margin: 34.0 dB 10.0 dBOutput Power: 16.0 dBm 12.0 dBmAttenuation: 10.0 dB 6.0 dBDefect Status: None None Last Fail Code: NoneSelftest Result: 0x00Subfunction: 0x15Interrupts: 1453 (2
[code]....
View 3 Replies
View Related
Feb 24, 2013
I have encounterd a broplem on my Cisco 805 model.
When i use the command "show ip interface brief" the status shows "up" but the protocol is "down" on my serial interface.
The link between my to sites is down after this happend.
View 1 Replies
View Related
Jul 28, 2011
I just purchased a Cisco SF 102-24 unmanaged 100 series swith with a MGBSX1 mini-Gbic converter. My goal is to connect this to a building that is connected with a Black Box LH1706A-ST media converter that has 100mb ST fiber connections. In my testing the Black Box shows both a Fiber link and RJ45 port link at 100mb, but the MGBSX1 does not show any link lights or traffic. So a computer connected to the Cisco switch is not able to communicate over the fiber connection.
Can the MGBSX1 be connected to a media converter that only has 10/100 ST fiber connectors?
View 2 Replies
View Related
Jan 19, 2012
We have a number of 4507s. Most are managed via VLAN 1 address. All have multiple VLANS for traffic control. When I do a show ARP or show IP ARP the command only shows VLAN 1 info. No entries for any of the other VLANS on the switch.
View 2 Replies
View Related
May 17, 2012
I'm dealing with a 4506 switch that whn I try to apply "sh auth sess int xx" I get "Invalid Input Detected" ... Is there any way that I can get the authenticated session over a port even if I can't apply "sh auth sess int"?
View 1 Replies
View Related
May 1, 2012
I notice that show inventory not showing all members in a 3750-stack after we merged two stacks. Its only showing the master of the new stack, and the previous master of the old stack.
View 3 Replies
View Related
Jan 9, 2012
I have a switch 4948, with version 12.2.31.sga4 ( I dont found bug about monitor session) and we try to made port mirroring with a monitor session from a VLAN and port belong at this VLAN have traffic input and output, but in the destination port, I always see it output traffic..
Global command
Red-127#sh run | in moni
monitor session 1 source vlan 1127
[Code].....
View 3 Replies
View Related
Jan 1, 2013
what command will show the clock rate as received on the DTE side of a back-to-back configuration?the show controllers command shows the configured clock rate on the DCE side.But how about viewing the received clock rate on the DTE side?
View 4 Replies
View Related
May 21, 2012
we have three separated network segments going to one Cisco 3750 switch all is L2 .. from this switch is 100 mbit uplink.we need to apply some Qos mechanism not to saturate line by traffic from one network.. Configuration from various reason CANNOT be done on switch where 100Mbit line is terminated.. so all must be done on SW1,2,3..Correct me if iam wrond but as switches doesnt see traffic from other network iam affraid only think we can do is limit bandwidth on links going into SW1,2,3 to 33 Mbit.I found commad srr-queue bandwidth limit.But links going to SWs are 1Gbit so if i force bandwidth to 10% (minimum what command allows) its 100 Mbit..If I force speed on those links to 100Mbit and than apply srr-queue bandwidth limit to 30% doest it work.??. Will srr-queue bandwidth limit speed to 30Mbit?? Or srr-queue bandwidth limit is calculated from maxim speed of interface?
View 1 Replies
View Related
Oct 10, 2012
Have a quick question regarding inter-vlan routing on a 3750. Overview of network is ISP --> ASA --> 3750 (acting as my core and default gw). I have 5 vlan interfaces on my 3750, all w/ 192.192.x.x subnets, a 6th w/ 192.168.100.x, and a 7th w/ 192.168.200.x. I have enabled "ip routing" on the switch and can successfully ping from subnet A to subnet B as long as both devices are using the correct DG for their vlan, which is the switch. I have a few ports that are trunked as well that go to ESX hosts which break out the vlans according to the subnet the vm should be attached to. The ASA is set to nat internal traffic for all the vlans.
Now my question: short of applying an ACL to each vlan interface to block traffic from other 192.192.x.x subnets is there a better way to accomplish this? I want my 192.168.10.x subnet to be able to reach all the subnets, but don't want 192.192.10.x to be able to talk to 192.192.20.x for example. I was thinking to create an acl like this:
access-list 120 permit ip 192.192.10.0 0.0.0.255 access-list 120 deny ip 192.192.0.0 0.0.255.255 192.192.10.0 0.0.0.255access-list 120 permit ip any 192.168.100.0 0.0.0.255 192.192.10.0 0.0.0.255
and then applying this to the interface for the appropriate vlan.
View 4 Replies
View Related
Dec 12, 2012
Cannot set route map on interface vlan. which in non default vrf on Cisco 3750.IOS c3750-ipservicesk9-mz.122-55.SE.bin sdm prefer route in enable ip vrf users rd 200:0 route-target export 200:0 route-target import 200:0 interface Vlan201 description Users 1 ip vrf forwarding users ip address 10.31.76.1 255.255.252.0 ip helper-address 10.31.4.57 route-map fromuser permit 10 match ip address fromuser set ip next-hop 10.31.128.155 When I enter "ip policy route-map fromuser" to interface Vlan 201 I heve the message:
% Remove VRF configuration from interface Vlan201 first
View 5 Replies
View Related
Jan 29, 2012
How to understand "show sessions" and "show connection" commands? And what is the difference between the two?
View 2 Replies
View Related
Feb 21, 2013
I have One switch 3750 and many switch 2960 c.I use one ASA 5510 to reach emote branche site (vpn conexion).I use one router 1841 for internet conexion.Router 1841, ASA and catalyst 2960 are connected on the 3750.Default gateway of all user is ASA IP
I configured Vlan 3750 and it work.Now I need to implement security : permit/block specific traffic between vlan [code] From vlan 72 I cannot have remote access on computer in vlan 34 and I cannot ping computer in vlan 34.
View 1 Replies
View Related
Nov 13, 2011
I am trying to setup a network using Cisco 2960 switches with vlans configured. One vlan will handle video coming from four cameras that are connected to another 2960.
We have four cameras feeeding one port each on a 2960, that 2960 in turn feeds one port on the main 2960 which is the video vlan for that site. From the site it goes back to a Cisco 3750 to be sent over to a Sonicwall firewall. If we connect to the 2960 that the camera are connected to we can see the video, but not on the main site 2960.
View 5 Replies
View Related
Feb 21, 2012
On a router I can use IP Accounting or Netflow to see what kind of traffic is moving over an interface. Are there any tools on a 3750 switch with a routed interface which would tell you who is hogging the bandwidth on that interface?
View 2 Replies
View Related
Jun 18, 2011
I have a cisco 1760 with running VIC-2FXO (working fine). I'm now trying to replace that line with an ISDN line through a VIC2-2BRI.
View 4 Replies
View Related
Feb 13, 2012
I have a 1t3/e3 card in a new 2951. When I statred the router, I found no interface corresponding to this module when do "show ip interface brief"
View 3 Replies
View Related
Nov 21, 2012
i'm going mad on following problem. I'm trying to get 2 networks seeing each other while one of the network is a non VLAN network and the other one is a VLAN network.They should use the same interface so i added VLAN e0/0.122 to the interface e0/0.Send a ping from my asa to both gw-IP's made me happy at first. In second in figured out that i cannot reach any client in the other network. For testing purpose i created an permit acl to any/any for both networks, but the packets still get dropped by the default implicit rule. (deny any/anyMaybe i'm to stupid for this
View 10 Replies
View Related
Jun 26, 2011
The Cisco 887 doesn't support the show dsl command, what is the command that I need to use to display the speed my ADSL is operating at? On the Cisco 877 the command I use is show dsl int atm 0 but this doesn't work on the 887
View 4 Replies
View Related
Feb 4, 2011
Wireless connection doesnt show up on Windows Xp, I now if it connected to the internet I could just install updates and it would automatically fix it, but I cant until i get it to connect?
View 1 Replies
View Related
Mar 1, 2012
my laptop isn't showing my wireless internet connection in the list.But my phone is connecting to my wireless internet connection without any problem.I am using a Toshiba Satellite laptop with Windows Vista.
View 3 Replies
View Related
Jan 15, 2012
Every once in a while when logging into Windows (7 Ultimate 32 bit) My PC decides it couldn't find a network connection, usually restarting the computer solved the problem, however now I have seemed to permanently be stuck on the "identifying" stage of my LAN connection. My mobo is an Asrock p67 extreme, the network adapter is a realtek pcie family card.Now I know it is not my modem since I can connect on my other PC in the living room, I verified this with a phone call to my ISP, they couldn't see my PC connected to the network but could see the other one.It is not the Ethernet cords, I switched them and even used a new one. I tried rolling back, installing updated and installing factory drivers for my network card, no change.
I tried turning off the PC, disconnected the power cord, discharged it, left everything off/ disconnected for 30 minutes and reattached, powered on, no change.I made sure my DHCP was on and that my PC was set to automatically retrieve IP/DNS.I even bought a new Ethernet card, installed it and I still can't connect, so its not the realtek card.I can't even access my modem using its UP address, 192.168.2.1 (Bell 2wire) but I can on my 2nd PC, it sees all other devices, PS3 /Smartphones but not my PC.
View 19 Replies
View Related
Nov 4, 2011
i have a packard bell network.i formatted the whole laptop.and now my laptop doesnot show any wireless network,however connects to dial up connection.i am using windows 7 ultimate 32 bit os
View 1 Replies
View Related
Apr 27, 2011
I am trying to connect to a different network, but for some reason when I click "Connect To", where it tells me to click to join another wireless network, it just shows me this: and does not show me the Wireless Networks that are available (I am not sure what it is called)
View 6 Replies
View Related
Jan 13, 2013
So, I happened to do CD recovery a day ago; *Due to forgetting Administrator password* and now my laptop seems to not be able to pick up any wireless connections when there usually is a ton. Also every time my laptop restarts it always loads saying "Preparing for first time use" Like I used the CD recovery again. which I didn't. I thought that maybe it has to do with the Drivers and such, though im not very tech fancy, so I wouldn't exactly know where to find the correct driver to install, and which to install.[code] Oh and lastly, I happened to notice on Driver manager, that on "other devices" there is a yellow exclamation point, on both of them: Intel(R) Centrino(R) Wireless-N + WiMAX 6150 and Network Controller.
View 1 Replies
View Related
Dec 15, 2010
I am running a DIR-825 I believe one of the original's no updates or anything. I run it mixed mode. The 2.4 shows up and I can connect to but the 5 ghz (n) speed says it's enabled but I can never see it when I scan on any of my wireless n products (laptops and other computers). Dlink support told me to change to mixed mode g and n. I was running it in mixed mode (a, g and n). D link told me to change to mixed mode g and n and to make sure they stay on channel 6 and 11. Is this correct. Which firmware should I upgrade to and is there any easy way to do this?
View 4 Replies
View Related
Aug 8, 2012
LMS discoverd all my devices and updated the DCR. This devices are visible in DFM. For some of this devices i would like to change the threshold values. For some reason the devices are not visible in Monitor->Fault Settings->Seup->Threshold Settings (please see screenshot) Is there another approach to change the threshold values?
View 5 Replies
View Related
Sep 7, 2011
I Have installed LMS 4.0.1 for my client. I have also installed UTLite script on the domain controller as per instruction from cisco. When i look at the utlite.log i'm seeing message displayed below:
Failed to create Tables. Transaction Rolled back
Failed to create Tables. Transaction Rolled back
: com.sybase.jdbc2.jdbc.SybSQLException: SQL Anywhere Error -110: Item 'getAuthenticatedUsers_ACS' already exists
Intializing the Controler 9 = skt Pkg = com.cisco.nm.cm.ut.ctrlplane.ctrls.SocketCtrl
2011/08/25 14:59:14 main utlite INFO SocketListener: Socket Listener : Port : 16236
Started Socket Listener
[code]....
View 2 Replies
View Related
