I notice that show inventory not showing all members in a 3750-stack after we merged two stacks. Its only showing the master of the new stack, and the previous master of the old stack.
View 3 Repliesi have a VSS core that has 4 downstream links to 4 stacked switches. I connected each of the 4 links to different switch in the switch stack. I then created a port-channel that combines all the links from each switch. Is there any issues associated with this setup?
View 9 Replies View RelatedWe have several stacks of 3750 switches where this problem is occurring. All of the switches are running IOS version 12.2(50)SE3. (Yes, I know it's old.)
We're seeing inconsistency in how the stack reports members when issuing the following commands:
sow switch
show version
show inventory
Not all members are showing up in the output of the "show version" and "show inventory" commands. For example:
HUNTI-WV-WDAC03#sh switch
H/W Current
Switch# Role Mac Address Priority Version State
----------------------------------------------------------
1 Member 108c.cff2.ea00 15 0 Ready
2 Member 8cb6.4f0a.a600 1 0 Ready
*3 Master 8cb6.4f0a.9c00 1 0 Ready
(all three switches in stack are displayed)(code)
We have a stack setup with 2 C3750x-12s and 5 C3750x-48p switches. We have two of these stacks. One is working and responding with snmp just fine. Our second one is showing the errors in the logThe only difference i see between the two stacks right now are the sw versions.
View 1 Replies View RelatedI have stack of 2960 S switches.I can console only from Master not from memember switches is this default behaviour?
View 1 Replies View RelatedI have 2 Catalyst 2960S-switches configured in a stack. The uplink is configured as a cross-stack etherchannel. Now I want to upgrade the stack with a minimum of downtime for the connected hosts. The hosts are connected to the stack via cross-stack etherchannels. So my question is: How can I upgrade the stack and reboot the members with a minimum of downtime? If I use the archive download-sw command with the /reload-option, the stack is reloaded and the result will be downtime for the hosts while th stack is reloading. Is it possible to upgrade the stack and then reboot the members one by one in a controlled manner?
View 8 Replies View RelatedI have a 3750X stack of 6 switches, I have a terminal server console server plugged into the console ports of all 6 switches. I am having a strange issue where I can connect to the master via the console, get a login prompt then I can log in, but when I try and connect to any of the members then I get a prompt "Press RETURN to get started" When I push return, it just loops back to the same prompt again:
switch-6 con0 is now available
Press RETURN to get started.
switch-6 con0 is now available
Press RETURN to get started.
I can connect to the stack via SSH fine etc. I am running 15.0(1)SE2. The stack is configured for TACACS+ auth via Cisco ACS.
Switch# Role Mac Address Priority Version State
----------------------------------------------------------
*1 Master f0f7.55ba.2700 15 1 Ready
2 Member f0f7.5541.da00 14 1 Ready
3 Member a493.4c1e.4b80 13 1 Ready
4 Member f0f7.5585.cb80 12 1 Ready
5 Member a44c.1120.8e80 11 1 Ready
6 Member a493.4cc0.fa80 10 1 Ready
I am trying to come up with an inventory report of all our 3750v2 stack switches, but for some reason I could not get the serial number of the member switch under each stack. Can Ciscowork LMS 3.2 see the serial number for each switch under a stack?
View 2 Replies View RelatedI have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies View RelatedFor an assignment in a class I am taking I created a simple network using GNS3 and set up static routing. Everything works fine, I can ping all of the hosts. One of the questions I am supposed to fill out is what happens when I use the "show ip route" and "show ip protocols" commands. When I use "show ip route" I get what seems to be the correct output. However when I use the "show ip protocols" command nothing happens. No output, no error, no nothing. It just goes right back to the prompt. This happens exactly the same on both routers in my network. incase it matters the router is c3640.
PS. would the output be non-existent because I have not set up any ip protocols. In a similar assignment I set up rip and when I used "show ip protocols" i did get what appeared to be the correct output. However I didn't write it down and when I put in the command again about an hour later after I took a break I also did not get an output until I re-entered the rip related commands.
I'm troubleshooting a 3750 switch stack problem where computers are showing input and CRC errors. I'd like to be able to execute a "show interface" command that will show me only the line showing the switch port and the line showing the input errors, but so far I can't figure out a way of combining those two parameters.
If I do "show interface | include Ethernet[0-9]�" I get all the lines showing the port numbers:
GigabitEthernet1/0/1 is up, line protocol is up (connected)
GigabitEthernet1/0/2 is up, line protocol is up (connected)
GigabitEthernet1/0/3 is up, line protocol is up (connected)
[Code].....
I have two 3750s stacked and one 3750 standalone all in one data closet. The both have the same versions. I want to combine them to make one stack. How do I force the standalone to be the master? sw 1 priority XX(Higher then the existing stack)? Both the stack and the standalone have management addresses. Would it be ok to delete the stack ip address? That way, the standalone(master's address will be the only management address)?How should I connect the standalone 3750 to the stack? At present, the 3750 stack is connected via a cascade cable going from the stack 1 port of the top switch to the stack 2 port of the bottom switch.
View 19 Replies View RelatedI have a stack of 4 3750 Switches.
1. WS-C3750G-12S
2. WS-C3750G-12S
3. WS-C3750X-48P
4. WS-C3750X-48P
The stack cable connected to Switch 1 Port 1 and Switch 4 Port 2 will not come back online. The logs show that there was a Stack line change. I have replaced the 1 meter Stack cable from Switch 1 to Switch 4 three times and it still does not come back online. This is the part that is interesting.. I have disconnected Port 1 Switch 4 and connected it to Port 2 Switch 4 and then Switch 4 came back online. This made me think Port 2 on Switch 4 was working correctly. Then I disconnected Port 2 Switch 1 and connected it to Port 1 Switch 1 and then Switch 1 came back online.
i have two cisco 3750 in stack firts, master switch have all swports busy second have only 5 how can i see cpu utilizations of the second switch, and its reasonable to move somme devices from first switch to second for deacreases of cpu and memory utilisatio ns of the master? the stack tehnologies use both cpu as one? or its only for simple management ?
View 9 Replies View Relatedhave a cable i think is bad, is it possiable to switch the cable out without causing any downtime to the switch or connected devices?
HQ-1st-Flr-Stack#show switch stack-ports summary
Switch#/ Stack Neighbor Cable Link Link Sync # In
Port# Port Length OK Active OK Changes Loopback
Status To LinkOK
[Code].....
I just need a little refreshing on upgrading a stack of 3750's. This stack only has 2 switches: [code]
1.) If I remember correctly I simply tftp the IOS to the flash of each switch and then reload the master only?
2.) Can I safely assume these are the 2 flash locations:
i want to remove an access layer 3750 48 POE master switch and replace with a new 3750 switch in the stack. i want to copy the same configuration to new switch since the old switch is having POE issue and I got replacement of the malfunctioned switch. we have VTP domain is configured in the network...
View 3 Replies View RelatedI have been given 2 3750 switches and need to put a config onto it wuld is for 2 3750's in a stack, how should I put this on the 2 switches? Is it bested to install it onto 1 switch first then physically attach the 2nd after?
View 3 Replies View RelatedOne of the stack member has failed and we need to replace the same with the new one.
[code],....
I'm setting up a web cache using the wccp protocol on a Catalyst 3750 stack.
Probably missing something real simple here but when I from the global configuration mode are trying to enter the ip wccp command it just says "invalid input" from wccp. There is no such command.. should be supported on my device from IOS 12.2(37)
We have two 6k5 configured as vss and it is working fine. For each floor we have a 3750 stack. In each 3750 stack we have 4 switches. From the first 3750 we have a fiber link to the first 6k5 and from the fourth switch we have another fiber link to the other 6k5 switch, for each floor/3750 stack, both configured as etherchannel. We installled each 3750 stack/floor in different maintenance windows; in all these installations we have problems configuring the etherchannel. After we configure the etherchannel on 3750 stack and in the vss, the etherchannel does not go up/up. We see the etherchannel up/down; after a lot off work, try and error, configuring shut/ no shut, adding and excluding links from the etherchannel; in any aleatory moment the etherchannel goes up/up and works fine. Is there any bug related with these IOS versions, or is there any right procedure to configure etherchannel from vss to 3750 stack?
3750 stack config (IOS
Cisco IOS Software, C3750 Software (C3750-IPBASEK9-M), Version 12.2(50)SE1, RELEASE SOFTWARE (fc2))
interface GigabitEthernet1/0/1switchport trunk encapsulation dot1qswitchport trunk allowed vlan 100,101,371,372switchport mode trunkchannel-group 1 mode on!interface GigabitEthernet4/0/1switchport trunk encapsulation dot1qswitchport trunk allowed vlan 100,101,371,372switchport mode trunkchannel-group 1 mode on!interface Port-channel1switchport trunk encapsulation dot1qswitchport trunk allowed vlan 100,101,371,372switchport mode trunk
[code]....
I currently have 5 3750s connected via Stackwise. This stack is connected back to my core (6509s) via fiber (1Gig to Core1 & 1Gig to Core2). I want to move the 5th 3750 to another closet due to an addition of a new patch panel. Due to max length of 10 ft. for stackwise, my plan is to connect this 5th switch back to the stack using trunked fiber ports, with them being an etherchannel (2Gig). Also plan to use single fiber port form 2 different switches in the stack to provide some redundancy for the 5th switch. Should I be alert of any issues with this connection design? Do I need to properly remove the 5th switch from the stack using, no sw 5 provison sw-model or can I just disconnect stackwise and connect back with fiber?
View 2 Replies View RelatedI had 2 3750 stacked and one of them decided to die (power supply) cisco replaced it and now i want to re-add that switch to stack. I have already upgraded my replacement switch to the same IOS version.I was reading that i can do it without powering down operational 3750 so the action plan so far is:
-power down NEW member
-connect stacking cable
-power up
as you can see my switch 2 is now a master and it still holds config of all Gi ports for switch 1. If i connect my NEW switch without any config (vlan.dat and startup-config) will my existing switch 2 copy all ports config to new switch ?
We had an "Event" on our process network at the mill yesterday. I connected a new WS-C3560V2-48TS-S to our network and we lost communications with all of the other switches.
The core is a stack of 3 WS-C3750 switches, one is a -24TS-1U and the other two are -12S-S. These connect to 10 WS-C3560G-24TS and 5 Rockwell Stratix 8000 (IE3000) over fiber. I am planning on replaceing two 24 port switches with the new 48 port. I had the switch configured and running at my work bench. It was connected to the network with one sfp module and ran all weekend with no issues. Yesterday afternoon I took it to the network cabinet and installed it. I powered it up and connected two sfp modules to the fiber patch panel and made the connection at the core stack.
Everything looked OK. I had communication link lights working on everything. Within minutes, we lost communication with every switch connected to the core stack. I shut down the new 48 port switch and the network slowly came back up.
The new 48 port is configured with Flex Links for the fiber redundancy protocol and was connected to each of the 3750G-12S-S stack members.
I though it might have been a power issue but the stack is UPS protected and shows it has been up for over 10 weeks. I'm not even sure "Crash" is the best decription for what happened. The new switch has a high enough IP address that it would not take over as a IGMP Querier.
I am working with 3750 switch.I console the switch and turn it on and it doesn’t show text in hyper terminal with any BAUD (I tried all the speeds). The hyper terminal works with other switches so the problem is not with the hyper terminal.when I tried to break the password it stuck after I was writing "flash_init" and when I entered or typed text it show only garbage characters. I tried to break the password with all the speeds and it shows garbage output. I tried to turn on the switch and hold control + break and it showed the text only with the speed 115200, but after I left holding and tried to type it showed only garbage again. Also I tried to copy text from the notepad to the hyper terminal.
View 6 Replies View RelatedAny one try to form a stack with mixed 3750-X and 3750G? Is there any prerequisites in hardware and software?
View 5 Replies View RelatedI've a situation where I need to add a new 3750x to a existing stack of 3750. [code] When I tried to stack them together, I get a version mismatch error. Is this because of the difference in SW Image? What are my options next ? My ultimate goal is to make the new switch stack correctly with the exisitng switches.
View 11 Replies View RelatedI configured 3750 A switch with vlan 20 and its IP address 192.168.20.41Its default gateway was 192.168.20.3Then i configured 3750 B switch with same default gateway and vlan 20 IP 192.168.20.43My question is now when we stack it becomes single switch and now vlan 20 ip address is 192.168.20.43 thats only IP i can see.So how does stack switch choose vlan 20 IP?Does it choose highest IP address between two switches if they have same vlan 20 as in my case?Also when i go to switch 3750 b by session command and do sh ip route it does not show ip default gateway .Also it shows vlan 20 as admin down .
View 5 Replies View RelatedI am replacing our 2 3750s which are in a stack and are running in VTP server mode for the domain with 2 new 3750Gs. There are 4 trunks to other switches which bare in client mode and 2 trunks to 2 ASAs which are in active/standby mode (one in each switch). Anyway what will happen to the VTP clients when I replace the stack as the revision number will be 1 on the server? The clients will ignore any VTP updates from the server ?
View 6 Replies View RelatedI have a doubt. In my environment I have two Switch 3750-X in stack.
My question is: How to shutdown remotely only a switch in stack?
attached diagram and following is the basic configuration on L3 and L2 switch. Is this configuration sufficient for simple routing?
L3SWITCH:
switch 1 priority 15
switch 2 priority 10
[Code].....
I am getting a version mismatch when adding the following 3750X to the 3750 stack:
WS-C3750X-48 12.2(55)SE3 C3750E-UNIVERSALK9-M
2 0 WS-C3750-24TS 12.2(25)SEA C3750-I9K91-M
Can I upgrade the 3750's to be able to correct this? Which version does this require?
What will be the recommended connectivity of stack power cable in 6 number of 3750x switches ?
Is it similar to the stack cable ?