Cisco Switching/Routing :: 3750 Switch Doesn't Show Text
Apr 26, 2013
I am working with 3750 switch.I console the switch and turn it on and it doesn’t show text in hyper terminal with any BAUD (I tried all the speeds). The hyper terminal works with other switches so the problem is not with the hyper terminal.when I tried to break the password it stuck after I was writing "flash_init" and when I entered or typed text it show only garbage characters. I tried to break the password with all the speeds and it shows garbage output. I tried to turn on the switch and hold control + break and it showed the text only with the speed 115200, but after I left holding and tried to type it showed only garbage again. Also I tried to copy text from the notepad to the hyper terminal.
View 6 Replies
ADVERTISEMENT
Mar 13, 2013
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies
View Related
Jan 16, 2012
I'm troubleshooting a 3750 switch stack problem where computers are showing input and CRC errors. I'd like to be able to execute a "show interface" command that will show me only the line showing the switch port and the line showing the input errors, but so far I can't figure out a way of combining those two parameters.
If I do "show interface | include Ethernet[0-9]�" I get all the lines showing the port numbers:
GigabitEthernet1/0/1 is up, line protocol is up (connected)
GigabitEthernet1/0/2 is up, line protocol is up (connected)
GigabitEthernet1/0/3 is up, line protocol is up (connected)
[Code].....
View 9 Replies
View Related
May 1, 2012
I notice that show inventory not showing all members in a 3750-stack after we merged two stacks. Its only showing the master of the new stack, and the previous master of the old stack.
View 3 Replies
View Related
Jan 9, 2013
I created the configuration below to limit the bandwidth, but doesn't work
Qos - 3750
!
mls qosmls qos map policed-dscp 10 to 8!class-map match-all Testmatch access-group name ACL!policy-map QOSdescription Limit 10M set ip dscp af11 police
[Code]....
View 6 Replies
View Related
Nov 2, 2011
i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies
View Related
Apr 16, 2013
I have PC_A and PC_B connected to the same switch, and are put in the same vlan. PC_A is the master (source) and PC_B is the destination (client). IGMP Snooping is enabled by default.
Is there any reason why this should fail? There is no RP or any interface with PIM enabled. Its a flat network with a source and client in the same vlan...
IH-3750-LOADTEST-101#show ip igmp snooping vlan 724
Global IGMP Snooping configuration:
-------------------------------------------
IGMP snooping : Enabled
[Code].....
View 19 Replies
View Related
Nov 18, 2012
I have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies
View Related
Jan 10, 2012
My network generally runs older routers (2600 series) with 16 port switch modules (NM-ESW-16). This has always worked great since I can configure the router and the switch ports on the fly, making changes to either as necessary. Well I am upgrading to 2811 routers, and we wanted to get gigabit ethernet ports on our switch modules. I think I made an error when I purchased a few of these switch modules: NME-16ES-1G.
The first problem, is that the switch ports don't even show up on the router config, I have to establish a session into the switch, (And I can't seem to get back to the router unless I manually switch off power and restart). I don't like this type of switch module, it's like I'm running a completely separate device, and while having a layer 3 switch is cool, It doesn't let me setup routing protocols so I don't like doing it this way. I want to go back to using a switch module that simply adds a ton of ports to my router like the NM-ESW-16. (Note: The NM-ESW-16 does actually work in the 2811 and would be perfect if it were Gigabit speed.)
The seconds problem is that the NME-16ES-1G isn't actually a Gigabit switch. It has a single gigabit port, but the 16 ports are all Fastethernet, and not gigabitethernet. So ideally, I am looking for a switch module that I can fully configure from the router interface that has 16 gigabitethernet ports, and works with a 2811. IE I want to do this. [code]
View 4 Replies
View Related
May 21, 2012
we have three separated network segments going to one Cisco 3750 switch all is L2 .. from this switch is 100 mbit uplink.we need to apply some Qos mechanism not to saturate line by traffic from one network.. Configuration from various reason CANNOT be done on switch where 100Mbit line is terminated.. so all must be done on SW1,2,3..Correct me if iam wrond but as switches doesnt see traffic from other network iam affraid only think we can do is limit bandwidth on links going into SW1,2,3 to 33 Mbit.I found commad srr-queue bandwidth limit.But links going to SWs are 1Gbit so if i force bandwidth to 10% (minimum what command allows) its 100 Mbit..If I force speed on those links to 100Mbit and than apply srr-queue bandwidth limit to 30% doest it work.??. Will srr-queue bandwidth limit speed to 30Mbit?? Or srr-queue bandwidth limit is calculated from maxim speed of interface?
View 1 Replies
View Related
Nov 25, 2012
i have a cisco 3560x poe. ny currnet version is 12.2(58)SE2.the cpu process is aboute 30% average.my problem is- ping to the switch itself show me 12ms which is high latency.*note- data between two hosts no this has no latency.i realize the packet go into the cpu itself but, the cpu is not loadedusy. so my question is- is this natural behavior?
View 2 Replies
View Related
Dec 5, 2012
I have been working on some Catalyst 3750's running 12.2(55)SE6 and hit an issue with CEF load-balancing over multiple equal-cost paths. Anyway this issue is now solved but it introduced me to the command 'show platform forward' - this shows you how the forwarding of a packet would be done via hardware cef (as opposed to the command 'sho ip cef exact-route' command that only shows the software cef path). Anyway I tried the command on a 3560G running 15.0(2)SE and it crashes the switch. I tried it a couple of times and verified that the MAC & IP addresses were exactly right in the command and each time the switch crashes. I have extracted the relevant bits from the crashinfo and attached them.
View 3 Replies
View Related
Dec 11, 2012
a new LAN installation, two VSS pair 6509 core, 15 closets, with 3750 stacks. Floor 15 only, devices/hosts can ping teh DHCP server but cannot aquire IP addresses. no such problem on other floors?
portfast an dother parameters are intact.
View 2 Replies
View Related
Oct 15, 2012
I want my computer to send a SMS txt message to my cell phone when a certain text message get written to by another program. Purpose is to alert to a certain action, an event, has occured that the program is monitoring.The cell phone uses Verizon as the carrier.
View 1 Replies
View Related
Dec 17, 2011
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
View 4 Replies
View Related
Jul 27, 2012
I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
View 4 Replies
View Related
Apr 16, 2012
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies
View Related
Mar 11, 2012
I'm running into what seems a basic ip routing config problem with a Catalyst 3750 (IP Base) switch. I have several VLANS configured on the switch with IP routing enabled, and the switch is connected to the inside interace of a new ASA 5520 as follows:
ASA5520 IP (Default gateway): 192.168.1.1Switchport Gi1/0/1 is configured as a routed port, IP address 192.168.1.3 255.255.255.0Example VLAN is VLAN 100, IP address 192.168.100.1 255.255.252.0 From the switch CLI, I can ping all VLAN addresses, as well as the ASA5520, and the client laptop I'm testing with from VLAN 100.
From the client laptop on VLAN 100, I can ping all switch interface and VLAN addresses (inter-VLAN routing is working), including 192.168.1.3, but I CANNOT ping the default gateway at 192.168.1.1.
Here is the relevant configuration information on the 3750:
!
no aaa new-model
switch 1 provision ws-c3750x-24
system mtu routing 1500
[Code]....
View 4 Replies
View Related
May 27, 2012
Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies
View Related
Mar 9, 2012
I have upgraded my C3560-PS-S switch to the latest IOS version 12(2)55-SE4 and it is not providing PoE anymore? It used to work before this upgrade? I searched Cisco bugtrack and there is bug defined for this IOS/Switch.
Switch(config-if)#do show power inline Available:370.0(w) Used:0.0(w) Remaining:370.0(w)
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Fa0/1 auto off 0.0 n/a n/a 15.4
Fa0/2 auto off 0.0 n/a n/a 15.4
Fa0/3 auto off 0.0 n/a n/a 15.4
Fa0/4 auto off 0.0 n/a n/a 15.4
Fa0/5 auto off 0.0 n/a n/a 15.4
Fa0/6 auto off 0.0 n/a n/a 15.4
Fa0/7 auto off 0.0 n/a n/a 15.4
Fa0/8 auto off 0.0 n/a n/a 15.4
Fa0/9 auto off 0.0 n/a n/a 15.4
Fa0/10 auto off 0.0 n/a n/a 15.4
Fa0/11 auto off 0.0 n/a n/a 15.4
Fa0/12 auto off 0.0 n/a n/a 15.4
Fa0/13 auto off 0.0 n/a n/a 15.4
Fa0/14 auto off 0.0 n/a n/a 15.4
Fa0/15 auto off 0.0 n/a n/a 15.4
Fa0/16 auto off 0.0 n/a n/a 15.4
Fa0/17 auto off 0.0 n/a n/a 15.4
Fa0/18 auto off 0.0 n/a n/a 15.4
Fa0/19 auto off 0.0 n/a n/a 15.4
Fa0/20 auto off 0.0 n/a n/a 15.4
Fa0/21 auto off 0.0 n/a n/a 15.4
Fa0/22 auto off 0.0 n/a n/a 15.4
Fa0/23 auto off 0.0 n/a n/a 15.4
Fa0/24 auto off 0.0 n/a n/a 15.4
View 3 Replies
View Related
Oct 31, 2011
I've 3750X switch that isn't loading email. then I went to rommon mode and accidently for "format flash". after that I loaded 15.0 SE2 s/w on it using tftp server but it doesn't boot up with that image. flash had only .bin file after I loaded it from tftp server.
since it wasn't booting up, I did format flash again and thought to load image again from tftp server but now, it doesn't load image from tftp server.
View 9 Replies
View Related
Nov 7, 2011
configure qos in Cisco 3750 switch.I have configured below template and applied on the vlan interface.But i am getting the hit on the access list but I am not able to get hit on the class map.
View 2 Replies
View Related
Jul 19, 2012
I had a bad expirience with Switch 3750-X. Because of an auditing security processess, my customer ran a software called "Nessus" to do a scanning of vulnerability on the network. When this software is point to switch, the process of the switch will next to 100% and reset. The software only do a listening on the ports to see what ports are opened and the switch should not reset because this. Bellow is the log os switch on the moment of test; we note that the processess 'HTTP' rise moments before the switch reset. I disable the HTTP service on switch but the problem persist. The test was made only one machine connected to switch.
View 4 Replies
View Related
Aug 12, 2012
We have three Cisco 3750 - 48port POE -LAN switches and i am trying to see if there are any issues when we stack POE and Non-POE type of switches.Aslo looking for information on the advanatage and disadvantage the stacking can provide on a Cisco 3750 48port.
View 3 Replies
View Related
Dec 12, 2010
The question is: Will a 3750 switch route Jumbo frame sizes (e.g. 9000 MTU)?
We know that we can change the System MTU to 9000, and someone on a previous thread said that we can change the Routing MTU to 9000 as well, although I couldn't figure out how to do that. However, regardless of how we configure the System MTU and Routing MTU, I don't think we're able to adjust the MTU on L3 VLAN interfaces, so if we want to actually "route" between VLANs on the switch, we're limited to 1500 MTU.
Our situation is that we have a customer connecting to our 3750 switch, and this customer wants to use Jumbo frames. The customer connects to our 3750 switch via their own VLAN, with their own L3 VLAN interface configured on the switch. The customer will point their traffic towards the L3 VLAN interface, then we want to route them onto another VLAN, via a different L3 VLAN interface, before forwarding their traffic. Because of the limitations noted above, specificially regarding the routing between these VLANs via L3 interfaces, I do not think we'll be able to support 9000 MTU frames on this 3750 switch. I think the L3 VLAN interfaces will limit us to 1500 MTU, regardless of what we configured via the global System MTU and Routing MTU settings.
View 4 Replies
View Related
Jun 8, 2007
How do you properly remove the QOS queues and configs from the switch.A was using auto qos which created a whole mess of qos configs on my running-config. I did "no mls qos" in conf term but that did not remove the queues.
View 3 Replies
View Related
Jun 21, 2012
i want to remove an access layer 3750 48 POE master switch and replace with a new 3750 switch in the stack. i want to copy the same configuration to new switch since the old switch is having POE issue and I got replacement of the malfunctioned switch. we have VTP domain is configured in the network...
View 3 Replies
View Related
Sep 11, 2012
Cisco 3750, I'm trying to reset the password but cannot communicate with my switch
View 1 Replies
View Related
Dec 9, 2012
is it generally possible to connect another switch, such as a 3750 to a port of a fabric extenders (C2232PP-10GE)?
View 1 Replies
View Related
Apr 16, 2013
I have Layer_3 " 3750-x " , so I can't do any routing on the switch , so if I need to Upgrade the IOS what is the proffered image that support hte routing , and Is it free or should I pay?
View 7 Replies
View Related
Oct 19, 2012
In Cisco 3750 facing high CPU utilization for specific period. During this period traffic response times across the switch degrades. Steps to identify interface potentially generating traffic. I have attached 'sh proc cpu history' , ' sh ip traffic', 'sh proc cpu sorted' during troubled period .
View 5 Replies
View Related
Mar 27, 2013
I have a 2 member 3750-x switch stack that was upgraded to 15.2 today via CNA. All the files were transfered and expanded correctly and it got to the step where the switches needed to be reloaded but on reload they froze.
I connected a console cable and power cycled the stack. I see the flash initialize and then the IOS image start to load. Lots of @ symbols and then nothing. It just sits there. The system light on the switches, while flashing green during the load, is now off. No light at all. But fans are running and the process will repeat itself if power cycled.
View 5 Replies
View Related
Nov 17, 2012
i have standalone 3750 switch. RPS light is green and system light is off.
3750TS#sh env all
FAN is OK
TEMPERATURE is OK
[Code].....
i have another switch with same model and ios its RPS light is off and system light is green
View 5 Replies
View Related
