Cisco Switching/Routing :: 3560G 15.0(2)SE - Show Platform Forward Command Crashes Switch?
Dec 5, 2012
I have been working on some Catalyst 3750's running 12.2(55)SE6 and hit an issue with CEF load-balancing over multiple equal-cost paths. Anyway this issue is now solved but it introduced me to the command 'show platform forward' - this shows you how the forwarding of a packet would be done via hardware cef (as opposed to the command 'sho ip cef exact-route' command that only shows the software cef path). Anyway I tried the command on a 3560G running 15.0(2)SE and it crashes the switch. I tried it a couple of times and verified that the MAC & IP addresses were exactly right in the command and each time the switch crashes. I have extracted the relevant bits from the crashinfo and attached them.
View 3 Replies
ADVERTISEMENT
Feb 21, 2012
On a 3750 you can do a show platform port-asic stats drop command. Is there a corresponding command for 6500 chassis?
View 7 Replies
View Related
May 29, 2012
I know that an ELAM can be setup on a 6500 running ipservices 12.2(33)SXJ, however I noticed that following commands are not available on a 6500 router running advipservices 12.2(33)SXJ:show platform capture elam asic etc
So I wanted to know if there is an alternate way to setup an ELAM for troubleshooting purposes?
View 1 Replies
View Related
Apr 18, 2013
I have 3560g with 15.0(2)SE2 version. I try to give different default gateways for different interfaces.I've already changed the sdm, run "ip routing" and made interest interfaces in "no switchport" with ip addresses.
my route-map is "
route-map ABC permit 10
set ip next-hop 192.168.77.3"
and it is applied on the interface with "ip policy route-map ABC" but when I try to apply it says "%PLATFORM_PBR-3-UNSUPPORTED_RMAP: Route-map ABC not supported for Policy-Based Routing" everything is fine if I change from "set ip default next-hop" to "set ip next-hop" but it is not I need in the guide of the version it is said this statement is not in unsupported list of route-map commands.[URL]
View 4 Replies
View Related
Aug 29, 2012
is there a command available to run diagnostics in ASR port/SPA? the one below is from a juniper remote device. i was only able to find 'test interface' but haven't run this yet (currently in production).
View 5 Replies
View Related
Jun 19, 2012
I am using cisco c3660 to act as Terminal Server for the communication of production machines in my company, recently there is a communication lost issue happen and its due to physical cable unplug from the machine. to troubleshoot for this issues i have to physically go inside my production area to check on it, as i understand from vendor we can check on the physical machine to see whether the LED light on the module is green or not, but in case of need to troubleshoot at night time, its time consuming as i need to travel back to company. is there any command that i can issue in the router c3660 to check on the physical connection between c3660 router and the production machine? the IOS version is IOS (tm) 3600 Software (C3660-I-M), Version 12.1(4)
View 3 Replies
View Related
Sep 26, 2012
Any command similar to sup720 "show tcam counters" It doesn't work on Sup2t.....
View 2 Replies
View Related
Aug 13, 2012
i facing problem with my switch cisco 3560G, when it power on only System light is green and noting happen. i check with serial cable ( Console) but noting happen no booting.
View 2 Replies
View Related
Nov 9, 2012
We have Nexus 7K recently installed few months back with 2 Sup (Slot 5 & Slot 6).Recently recevied mesaanges in monitoring servervia SNMP:Alarm : active unit removal caused an auto SWACT However, when checked there are no recent logs which may be linked to this alarm. The show redundancy command output shows that Sup in slot 5 is active which in slot 6 is Hot Standby.
View 1 Replies
View Related
Feb 9, 2012
I enabled the "no service password-recovery" command on my C2960 switch. All seems to work as discribed. Only issue I have is --- which show command is used to reveal if the password-recovery feature is enabled of disabled as the command doesn't show up in the running config after you enable it ?
NOTE: The command does show up in the C2960 switch in config t mode (unlike the IOS router 2800 series), but doesn't show up in the running-config after you enable or disable it.
On the 2800 series routers (latest IOS) in config t mode the command does not show up but if you type "no service passowrd-recovery" the command function correctly and it does list it in the running configuration.
View 1 Replies
View Related
Nov 20, 2011
tell me if there is an equivalent command to Show int Summary on the Nexus 7000?
eg
MYCISCOSW01#show int summary
*: interface is upIHQ: pkts in input hold queue IQD: pkts dropped from input queueOHQ: pkts in output hold queue OQD: pkts dropped from output queueRXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)TRTL: throttle count
[code]....
I find it a useful command on the 6500 to spot high traffic flows.
View 7 Replies
View Related
Mar 29, 2012
know Cisco IOS command, how to show when Catalyst 2960 was shut down (power off)?
View 2 Replies
View Related
Jan 12, 2013
We have a Catalyst 3560G 24 port POE switch. It's been running fine for 1+ years. A few weeks ago we enabled SPAN on it to capture packets. Today, we had a random spike in CPU on the switch. Seems hardware swithing continued to work fine, but software based processes choked and effectively took down EIGRP, HSRP, etc. We collect syslogs from the router and we saw 2 crashes/reboots. Both showed the exact same error both times, with the same hex values. I **believe** the CPU usage dropped when a tech disconneted the SPAN port and it's state changed to down, but I'm not 100% sure.Could this indicate an IOS bug (I'm hoping it's not a hardware failure)? And, how to track this down to see if this could be related to SPAN? I've disabled SPAN for now.
View 3 Replies
View Related
Jan 22, 2012
I've a 7206VXR (NPE-G1) router. I would like to purchase a PA-GE port adaptor where I've to use a GBIC connector.
1. Is it possible to have a connection between PA-GE and a 3560G switch (4 SFP ports)? If yes, what type of cables & connectors are to be used?
2. Is there any GigabitEthernet port adaptors / modules for 7206vxr where I can connect RJ45 (cat 5) or SFP modules?
View 4 Replies
View Related
Feb 21, 2012
We have two 3560G-TS-E running 12.2(35)se2, configured as HSRP. Both are running ntp config "ntp peer 210.72.145.44" and it's pretty well that they get the correct time. Yesterday I upgraded the second device to IOS 12.2(58)se2 and ntp doesn't work now. I checked doc that 12.2(58)se2 runs ntp default version 4 so I change to "ntp peer 210.72.145.44 version 3" but still not work. I put here "show ntp" result for different IOS.
IOS 12.2(35)
SW01>show ntp status
Clock is synchronized, stratum 2, reference is 210.72.145.44
nominal freq is 119.2092 Hz, actual freq is 119.2022 Hz, precision is 2**18
reference time is D2EF12A5.2EB2DCB2 (15:07:17.182 GMT Wed Feb 22 2012)
clock offset is -4.6616 msec, root delay is 57.50 msec
[code]...
View 10 Replies
View Related
Apr 12, 2013
Configuring OSPF on a catalyst 3560G Switch to connect to our building next door by way of fiber. The other two switches in the other building are running OSPF, I am trying to connect to the other building and access a server which is on a switch running OSPF. I am trying to configure the switch here to run OSPF and be able to see the neighbor, but currently can't although I've identified the networks. Maybe I'm missing something, I've followed the instructions but something is not right.
View 15 Replies
View Related
Nov 27, 2011
I want to select catalyst 3560G for my network. But IOS SLB need to be implemented in my network. I only know catalyst 6500 series can support this feature and i am not sure whether 3560G can support this feature. what platform and IOS version i need to implement IOS SLB?
View 1 Replies
View Related
Apr 15, 2010
I have two 3560G 24 port switches. Each of them connects to some 3560G or 2950 switches. Trunks between 3560G are set as 1000/full. Trunks between 3560G and 2950 are set as 100/full. show int status also shows the interface negotiation is 100/full for trunks between 3560G and 2950. The issue is I keep getting outdiscard errors in trunks between 3560G and 2950. At 2950 switches, I see Recv-errors too. I checked all the trunks traffic. They are totally not high. Only serveal mbps. Most time even lower than 1mbps.
I googled this kind of issue online. I see it could be possibly caused by high volume traffic higher than the capacity. But it appears the traffic there is not high enough to cause this kind of issue. Is there any possiblity that could cause this problem?
The below is 3560G trunk configuration for 2950 switch
interface GigabitEthernet0/10 switchport trunk encapsulation dot1q switchport trunk allowed vlan 1-122,124-4094 switchport mode trunk speed 100 duplex full srr-queue bandwidth share 10 10 60 20 queue-set 2 priority-queue out mls qos trust cos auto qos voip trust
the trunk configuration at 2950 switch: interface FastEthernet0/24 switchport trunk allowed vlan 1-122,124-4094 speed 100 duplex full
View 16 Replies
View Related
Feb 21, 2012
cant assign cisco switch 3560G port g0/1to access vlan 10
main-switch(config-if)#switchport access vlan 10 Command rejected: Gi0/1 not a switching port.
View 5 Replies
View Related
Dec 28, 2008
what is the use of no switch port command in L3 switch?
View 7 Replies
View Related
Aug 9, 2012
I have some Ethernet-connected cameras that all have the same Ethernet MAC address FF:FF:FF:0A:0A:0A. They were originally designed to directly connect to a Windows PC, but they can also connect through a simple unmanaged switch.A Catalyst 3560 switch won't forward packets to or from anything with that MAC address, at least not by default. Is there a way to convince the switch to do so?
It was my hope to replace the dedicated connections we have for these cameras with a separate VLAN for each camera, and switch them through our existing switch network. Given that all of the cameras use the same MAC address, putting them on the same network is out of the question, but different VLANs, where the only two devices on each VLAN were the camera and the PC that uses it, would be fine.
The switches run IOS 12.2(55) SE through SE3. I learned the camera MAC address from the PC's ARP table while the camera software runs; it turns out the cameras don't have a full IP stack either and don't even do ICMP.
View 2 Replies
View Related
Dec 8, 2011
The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
View 4 Replies
View Related
Apr 26, 2013
I am working with 3750 switch.I console the switch and turn it on and it doesn’t show text in hyper terminal with any BAUD (I tried all the speeds). The hyper terminal works with other switches so the problem is not with the hyper terminal.when I tried to break the password it stuck after I was writing "flash_init" and when I entered or typed text it show only garbage characters. I tried to break the password with all the speeds and it shows garbage output. I tried to turn on the switch and hold control + break and it showed the text only with the speed 115200, but after I left holding and tried to type it showed only garbage again. Also I tried to copy text from the notepad to the hyper terminal.
View 6 Replies
View Related
Jan 10, 2012
My network generally runs older routers (2600 series) with 16 port switch modules (NM-ESW-16). This has always worked great since I can configure the router and the switch ports on the fly, making changes to either as necessary. Well I am upgrading to 2811 routers, and we wanted to get gigabit ethernet ports on our switch modules. I think I made an error when I purchased a few of these switch modules: NME-16ES-1G.
The first problem, is that the switch ports don't even show up on the router config, I have to establish a session into the switch, (And I can't seem to get back to the router unless I manually switch off power and restart). I don't like this type of switch module, it's like I'm running a completely separate device, and while having a layer 3 switch is cool, It doesn't let me setup routing protocols so I don't like doing it this way. I want to go back to using a switch module that simply adds a ton of ports to my router like the NM-ESW-16. (Note: The NM-ESW-16 does actually work in the 2811 and would be perfect if it were Gigabit speed.)
The seconds problem is that the NME-16ES-1G isn't actually a Gigabit switch. It has a single gigabit port, but the 16 ports are all Fastethernet, and not gigabitethernet. So ideally, I am looking for a switch module that I can fully configure from the router interface that has 16 gigabitethernet ports, and works with a 2811. IE I want to do this. [code]
View 4 Replies
View Related
Feb 5, 2012
I see the command "vlan access-log ratelimit 2000" and wonder what it is that it does.
View 2 Replies
View Related
Nov 25, 2012
i have a cisco 3560x poe. ny currnet version is 12.2(58)SE2.the cpu process is aboute 30% average.my problem is- ping to the switch itself show me 12ms which is high latency.*note- data between two hosts no this has no latency.i realize the packet go into the cpu itself but, the cpu is not loadedusy. so my question is- is this natural behavior?
View 2 Replies
View Related
Sep 30, 2012
I have cisco switch 3550 IOS Version 12.1(19)EA1c.
I can configure route-map commands on that. but i can not apply that into any vlan interface. while i try to apply the following command ( ip policy route-map PBR) on VLAN int i get an error msg saying that the command is not recognized.
View 3 Replies
View Related
Apr 3, 2012
I need to enable vPC "peer-switch" command on a pair of Nexus 7018s which are currently vPC peers (primary and secondary). The STP root and Secondary root are currently configured across these switches.Can I enable the peer-switch command in this configuration without impacting services, and then modify both switches to have the same bridge priority without impacting services ? We have a few downstream 5ks which are not dual homed to both vPC peers (work in progress) so need to understand if the peer-switch command will in any way break this connectivity for now.
View 1 Replies
View Related
Apr 18, 2012
What other command can be used to debug packets on a 3750 switch ?
View 2 Replies
View Related
Nov 9, 2011
Is there any command to display the GBIC in the switch because I need to replace 3550 but I have no exact part number
the model is WS-C3550-24-SMI
and try
sh inventory
sh hardware
sh diag
sh module
View 1 Replies
View Related
May 9, 2012
I config mdix on port gi1/0/7 as mdix auto IT does not show in running config.Is there any way or command which i can use to verify mdix on port?
View 2 Replies
View Related
Apr 9, 2013
a switch port is shutdown, but when i use NO SHUTDOWN command it is working and shows administratively down. like this command does not affect on it. i should enable this port? what can i do btw, port is not in errdisable and portfast is enabled.
View 3 Replies
View Related
Sep 11, 2011
Any equivalent show command to get the "FIB TCAM Usage" on An ASR 1006 ?the "show platform hardware capacity forwarding" does not work on ASR1006 Example on 6500: Router# show platform hardware capacity forwarding.
View 1 Replies
View Related
