Cisco Switching/Routing :: Switch 3550 - Command To Display GBIC In It?

Nov 9, 2011

Is there any command to display the GBIC in the switch because I need to replace 3550 but I have no exact part number

the model is WS-C3550-24-SMI
and try
sh inventory
sh hardware
sh diag
sh module

View 1 Replies


ADVERTISEMENT

Cisco Switching/Routing :: Route-map Command Support On Switch 3550?

Sep 30, 2012

I have cisco switch 3550 IOS Version 12.1(19)EA1c.   
 
I can configure route-map commands on that.  but i can not apply that into any vlan interface.   while i try to apply the following command ( ip policy route-map PBR) on VLAN int i get an error msg saying that the command is not recognized.

View 3 Replies View Related

Cisco Switching/Routing :: WS-C6513 - Display GBIC Module Info From Within IOS?

Apr 24, 2012

I have a Cisco WS-C6513 switch, with a couple of GBIC module cards in it.  I am trying to display the part number (or model number) of the modules which are inserted into this module card.  How to do that?  I don't want to schedule down-time to pull the module(s) - just to read the label!  :-)
 
This shows me info for the "module card": sh module 9 But this doesn't work: sh module 9/6

View 4 Replies View Related

Cisco Switching/Routing :: Recursive Command 3550 Won't Delete Directory

Apr 16, 2013

i have a few 3550's at the  moment and when i use the delete /force /recursive flash:html command it  just throws back "permission denied" this seems pretty common on the  3550 but i have never had an issue on the 2950, 3550, 2960, 3560 just  the 3550.
 
Can any give me the command for recursive deleting on the 3550 in the console i.e. hyper terminal?

View 6 Replies View Related

Cisco Switching/Routing :: Switch C3508G-XL Reboot After Plugging A GBIC Adapter

Dec 14, 2011

Everything is in the title...When I plug a GBIC  adapter on a port, my switch reload automatically..! Is it normal, because I did it during production and It disconnects some users.

View 0 Replies View Related

Cisco Switching/Routing :: Connect SF200-48 Switch Via Mini-GBIC MGBLX1 Fiber Module To 3750?

Jun 25, 2012

I am trying to connect a SF200-48 switch via Mini-GBIC MGBLX1 fibre module to a Cisco 3750 switch with a GLC-SX-MM fibre module installed both running a 1000 Mbps.  When connected together they do not enable.  Are there compatibility restrictions or is it that the Mini-GBIC modules cannot be used to uplink to a LAN?

View 2 Replies View Related

Cisco Switching/Routing :: 3550 / Layer 3 Switch Not Routing?

Apr 26, 2012

I have a 3550 l3 switch configured as follows:

vlan 10 ports 1-10
vlan 21 ports 11-20
vlan 30 port 21-30
vlan 40 ports 31-40
default vlan should be vlan 21

I have the servers, switch and router connected to vlan 21.  Vlan 21 works great I can browse the internet, but I cannot ping any other vlans. router is connected to fa0/19
 
[code]
Building configuration... 
Current configuration : 4833 bytes
 !
 version 12.2
 no service pad

[code]....

View 11 Replies View Related

Cisco Switching/Routing :: VLan Routing Same Switch 3550-12T?

Mar 10, 2013

I'm having some problems setting up vlans to talk to each other on a 3550-12T switch. Its quite a simple setup I have, but I need to split my network up.
 
Currently I have a network of 192.168.25.0 255.255.255.0 I want to create a new vlan network of 192.168.30.0 255.255.255.0 So I have configured my vlan1 (default vlan) to have an ip of 192.168.25.250 for getting to the management page
 
I have created a vlan2 of 192.168.30.1 255.255.255.0 ?I have a port 10 linked to one of my 3560G's?In port 9 which is on vlan2 I have my pc plugged in with a static ip of 192.168.30.50 from the router I can ping any device on 192.168.25.x.
 
I can not ping 192.168.30.1 (which is my vlan2) nor can i ping the PC.
 
I have enabled ip routing  But I dont have a default route, this is becase we don't have a router on the network.

View 18 Replies View Related

Cisco Switching/Routing :: What Is The Use Of No Switch Port Command In L3 Switch

Dec 28, 2008

what is the use of no switch port command in L3 switch?

View 7 Replies View Related

Cisco Switching/Routing :: GLC-GE-100FX - Connection To 3550 Switch Over MMF

May 21, 2012

i have an OM1 MMF fiber run between two switches, the first being a 3750 and the second being a 3550.
 
The link currently exceeds the maximum distance for OM1 @ 1000Mb/s (220m) so i would like to downgrade the link to 100FX using the necessary SFP's/GBIC's to extend the maximum distance to 550m and run the link @ 100Mb/s.
 
I have the part code for the 100FX SFP to install in the 3750 (GLC-GE-100FX) but cant find a 100FX GBIC for the 3550, can I use a 1000SX GBIC (WS-G5484) for the 3550 at one end and the 100FX SFP at the other? Any success with this configuration over MMF?

View 3 Replies View Related

Cisco Switching/Routing :: 3550 Upgrade To Gigabit Switch

Jun 4, 2013

I have a 3550 switch right now, and need to upgrade to a gigabit switch, so I'm looking at a 3560G-48.  For some reason I purchased an EMI version of my 3550, but run the ipbase image...what I need to look for - is a 3560G-48-s good for what I need?

View 4 Replies View Related

Cisco Switching/Routing :: Port Unreachable Messages On 3550 Switch?

Jan 24, 2012

While working at a client site today, I was troubleshooting some ICMP connectivity for a network we have created.I turned on 'debug ip icmp" on the 3550 switch int he middle, and was inundated with the following debug output:
 
Jan 25 11:01:14.641: ICMP: dst (172.16.1.7) port unreachable rcv from 172.16.1.5
Jan 25 11:01:14.641: ICMP: dst (172.16.1.7) port unreachable rcv from 172.16.1.5
Jan 25 11:01:14.641: ICMP: dst (172.16.1.7) port unreachable rcv from 172.16.1.5
Jan 25 11:01:14.641: ICMP: dst (172.16.1.7) port unreachable rcv from 172.16.1.5

[code]....
 
This output fires several times a second, and based on how often it is firing, I am curious if it may be a culprit with respect to the fact that the client has indicated that they have some slow internet.Should the next step be to look at the workstation at 172.16.1.5? 

View 10 Replies View Related

Cisco Switching/Routing :: Have HSRP Or GLBP Between Two Different Switch Like 3550 And 3560?

Dec 9, 2012

Can i have HSRP or GLBP between two different switch like 3550 and 3560?

View 3 Replies View Related

Cisco Switching/Routing :: How To Block Single Mac Address In 3550 Switch

Nov 16, 2011

I need to block this mac address in  my 3550 switch.i enable port security but this mac address comes and do the violation and port is shut down.

View 3 Replies View Related

Cisco Switching/Routing :: Catalyst 3550 Switch - Dynamic QoS Setup

Mar 28, 2012

I live in a condo building that uses 3 Cisco Catalyst 3550 switches connected to a Comcast router with 100 Mbps download. Currently we regulate bandwidth by providing each user with 3 Mbps download. Even if only two people are active they still only get 3 Mbps download. I would like to set it up so if two people are using they each get 50 Mbps; a sort of 'dynamic qos. Is this possible with these switches? Would we have to purchase a Cisco router in order to provide this feature?

View 9 Replies View Related

Cisco Switching/Routing :: Changing Native Vlan On 3550 Switch

Dec 22, 2012

I am having trouble after creating a management vlan (99) on a 3550 switch.I have configured the vlan (99) and given it an IP (192.168.1.100) and a default gateway (my router address - 192.168.1.99).I can ping to the switch from a PC and vice versa. The management VLAN IP is fine but now I cannot ping to the router from either the PC or the switch.It seems that just by adding VLAN 99 with it's own IP address has now prevented pings from the switch/ PC to the router ?Due to the fact that I have created a new switch management VLAN with an IP, does this mean I have set up the router as a 'router on a stick' scenario ? [code]

View 4 Replies View Related

Cisco Switching/Routing :: Enable / Disable Interfaces On 3550 Switch

Jul 14, 2012

I`m looking to automate some functions in a web application.Functions like enable/disable interfaces on a Cisco 3550 switch.

View 5 Replies View Related

Cisco Switching/Routing :: 3550 EMI Switch Is Not Responding To Power Connection

May 10, 2012

My cisco 3550 EMI switch is not responding to power connection. I have checked and changed power cable. its still not working.fan is not running and no lights on front panel

View 3 Replies View Related

Cisco Switching/Routing :: Internet Access For 3550 Switch VLANs?

Feb 22, 2012

I have a small cisco switch cluster (seven different 2924, 3524cisco switches) with 3550 as a cluster control which does all the inter vlan routing that works fine.
 
This cluster is in semi production PBX interop testing lab. This is a closed network without internet access and not connected to our corporate network.However now I have to add this capability so some equipment in the lab can get Microsoft updates over the internet.
 
I've created a port on a 3550 (fa0/19) and connected it to another network that has internet access. It picked an ip address and when I'm logged in to the 3550 I can ping hosts on the outside network. However I can't ping any hosts on that network from any hosts that are connected to my vlans.I've tried a few different things, but still can't make it to work.
 
Here is a short version of my 3550 configuration:

!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log datetime
no service password-encryption

[code]....

View 13 Replies View Related

Cisco Switching/Routing :: 3550 - Switch Disconnects Another Voip Phone?

May 14, 2013

im having this strange issue where everytime i plug in a voip phone to my 3550 the switch disconnects another voip phone.then to fix the disconnected phone (7940) i need to power off the phone 5-10 minutes then power it on again.

but the strange thing is, once i have to do that to fix the phone and connect the phone back to the switch, the port link is up, but no macs are seen on that port.

View 1 Replies View Related

Cisco Switching/Routing :: 3550 - Copy IOS To Switch In ROMmon Mode?

Jan 24, 2012

I have a 3550 switch that was replaced at a remote site with no IOS. This is a switch not a router so tftpdnld does not work.
 
[Code]...
 
The problem is the switches interface never comes up so try to connect to the tftp server. I read on google it can't be done on a switch to copy from tftp to flash in rommon mode on a switch and to use XMODEM. My problem is I do not have access to it, I ssh into a 3640 which is an access server for all devices and that is how I have console to it, how to use XMODEM over ssh.
 
But I'm fairly certain that there has to be a way to just copy it from tftp? I have a 3550 local and when I put it in rommon mode it stops the port check at port, port 1 goes from green when you plug it in to off then port 2 changes to amber and the rest green. So just by the look of this I would believe tftp would work; you just need to use port 1.

View 1 Replies View Related

Cisco Switching/Routing :: 3550 Switch - Software Forced Crash Exception

Feb 7, 2013

Our switch had a little crash-fest this morning at 2:30 AM. I did find a web page about diagnosing Software Forced Crash Exceptions, but it did not look like ours was one of the more easily-identifiable ones.
 
It may be worth noting that we've only used this switch for about a month, everything seemed fine until now. When we got the switch it did not have any GigE modules, and this week we put 2 into it and have been using them for 2 servers.
 
It looks like the switch was crashing repeatedly over a period of 20 minutes, and then it stopped and normalized. In the logs of the router that this switch uplinks into, we could see the ethernet port flapping during the time that the switch wasn't reachable.
 
Here's the Show Stack on the switch:
 
Sfld_3550#    show stackMinimum process stacks:Free/Size   Name4404/6000   vegas_flash init3352/6000   SaveCrashBuffer5716/6000   CDP BLOB8512/9000   IP Background5596/6000   vqpc_shim_create_addr_tbl5584/6000   SPAN Subsystem5552/6000   SASL MAIN4944/6000   vegas IPC process8704/9000   cdp init process5404/6000   RADIUS INITCONFIG4928/6000   Vegas CrashBuffer5664/6000   URPF stats2536/3000   Rom Random Update

[code].....

View 2 Replies View Related

Cisco Switching/Routing :: 3550 - Export Mac Address From Switch To Local Machine?

Jan 8, 2013

I am working on Cisco 3550 switch on a certain requirement. I have got an access point connected to the switch and few mobile phones connected to the access point. I get the list of mac addresses connected to the switch ( Both access point's mac address & the clients addresses) by "show mac-address table dynamic" command. However, i am unable/confused to get the output of the following scenarios:
 
1. I would require to export the mac address from the switch to the local machine in any format (May be by using an SNMP tool, if available) so that the same needs to be used in my C# for development.What would be the way for the same ?
 
2. The mac address in the mac address table doesn't get updated dynamically. (Eg Scenario: A wifi client gets connected to an access point which inturn is connected to the switch, the mac address of the client shows up in the switch table. However if the client is disconnected, the client's mac address would still be displayed in the switch table )

View 9 Replies View Related

Cisco Switching/Routing :: 3550 - Unable To Ping Internet From HSRP Standby Switch

Nov 16, 2011

I have router connected to 2  3550 switches  directly. 3550A  and B  switches are running HSRP. OSPF is running between Router and 2 switches.
 
From Switch B  i can ping the Router Wan interface but not the internet sites. from Switch A  i can ping any sites?
  
Switch B 
3550SMIB#                          sh ip routeCodes: C - connected, S - static, R - RIP, M - mobile, B - BGP       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area       N1

[Code]......

View 7 Replies View Related

Cisco Switching/Routing :: Cat 3560 No Switchport Command Test Out Routing With Switch

Dec 8, 2011

The last few days I've been exploring options in getting rid of some old routers accross a wan connections.  I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch.  I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect.  I'll post the config and a few commands so you can see what the basic setup is. 

Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254.  Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]

View 4 Replies View Related

Cisco Switching/Routing :: 6506E Switch Command Meaning

Feb 5, 2012

I see the command "vlan access-log ratelimit 2000" and wonder what it is that it does.

View 2 Replies View Related

Cisco Switching/Routing :: 7018 Is VPC Peer-switch Command Intrusive

Apr 3, 2012

I need to enable vPC "peer-switch" command on a pair of Nexus 7018s which are currently vPC peers (primary and secondary). The STP root and Secondary root are currently configured  across these switches.Can I enable the peer-switch command in this configuration without impacting services, and then modify both switches to have the same bridge priority without impacting services ? We have a few downstream 5ks which are not dual homed to both vPC peers (work in progress) so need to understand if the peer-switch command will in any way break this connectivity for now.

View 1 Replies View Related

Cisco Switching/Routing :: Command To Debug Packets On 3750 Switch

Apr 18, 2012

What other command can be used to debug packets on a 3750 switch ?

View 2 Replies View Related

Cisco Switching/Routing :: Command To Verify MDIX On 2960S Switch?

May 9, 2012

I config mdix on port gi1/0/7 as mdix auto IT does not show in running config.Is there any way or command which i can use to verify mdix on port?

View 2 Replies View Related

Cisco Switching/Routing :: (no Shutdown) Command Is Not Working In 2970 Switch Port

Apr 9, 2013

a switch port is shutdown, but when i use NO SHUTDOWN command it is working and shows administratively down. like this command does not affect on it. i should enable this port? what can i do btw, port is not in errdisable and portfast is enabled.

View 3 Replies View Related

Cisco Switching/Routing :: GBIC On 6509

Nov 7, 2011

I have an interesting problem. I have a 6509 that I'm trying to swap the GBIC on. The switch is already using a GLC-SX-MM GBIC and it is up/up and passing traffic, but we are getting some errors and suspect it may be faulty. 

I want to replace the GBIC with one of the identical model - a GLC-SX-MM. It was brand new, never been opened. When the new GBIC is plugged in the link light on the switch goes completely off (not amber) and the port goes into a down/down (not connect) state. There are no messages in the logs at all. It's like it doesn't even see it. If you plug the old GBIC back in then the link comes back up. I tried a different port with the same results.Thinking that the new GBIC may be faulty (even though it was brand new) I tried a second GLX-SX-MM, also new. That one does the same thing. 

At that point I thought there might be a problem with that switch, so I tried the GBICs on the other 6509 in that pair. The other 6509 is running the same hardware and software. The GBICs will not work there either. If you move the old, suspected faulty GBIC from 6509-2 to 6509-1 then that it works. 

The solution would seem to be that I have two faulty GBICs, but I'm having trouble persuading myself that I have two new ones, straight out of the package, that are both bad. Are there any other things to check on the switch? Here's the pertinent information: 

switch#show ver
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI3, RELEASE SOFTWARE (fc2)
<snip>
cisco WS-C6509-E (R7000) processor (revision 1.3) with 458720K/65536K bytes of memory.
Processor board ID SMG1109N3BK
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
[code]...

View 15 Replies View Related

Cisco Switching/Routing :: Copy Flash Tftp Command Failed On 3750 Switch

Oct 5, 2010

I have a cisco 3750 swicth which i want to load a new ios to but unfortunately there's no enough space on the flash. This means that i need to backup the cureent (old) ios to my tftp server but the command keeps failing. It always gives 'No such file or directory' error .The free space on the flash is 8mb and my new ios is about 11mb.I also went inside the directory where the old is and inputed the same copy command but to no avail.Below are some of the command failure on the swicth:
 
[code]....

View 25 Replies View Related

Cisco Switching/Routing :: 3560G 15.0(2)SE - Show Platform Forward Command Crashes Switch?

Dec 5, 2012

I have been working on some Catalyst 3750's running 12.2(55)SE6 and hit an issue with CEF load-balancing over multiple equal-cost paths.  Anyway this issue is now solved but it introduced me to the command 'show platform forward' - this shows you how the forwarding of a packet would be done via hardware cef (as opposed to the command 'sho ip cef exact-route' command that only shows the software cef path).  Anyway I tried the command on a 3560G running 15.0(2)SE and it crashes the switch.  I tried it a couple of times and verified that the MAC & IP addresses were exactly right in the command and each time the switch crashes. I have extracted the relevant bits from the crashinfo and attached them. 

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved