Cisco Switching/Routing :: How To Block Single Mac Address In 3550 Switch

Nov 16, 2011

I need to block this mac address in  my 3550 switch.i enable port security but this mac address comes and do the violation and port is shut down.

View 3 Replies


ADVERTISEMENT

Cisco Switching/Routing :: 3550 - Export Mac Address From Switch To Local Machine?

Jan 8, 2013

I am working on Cisco 3550 switch on a certain requirement. I have got an access point connected to the switch and few mobile phones connected to the access point. I get the list of mac addresses connected to the switch ( Both access point's mac address & the clients addresses) by "show mac-address table dynamic" command. However, i am unable/confused to get the output of the following scenarios:
 
1. I would require to export the mac address from the switch to the local machine in any format (May be by using an SNMP tool, if available) so that the same needs to be used in my C# for development.What would be the way for the same ?
 
2. The mac address in the mac address table doesn't get updated dynamically. (Eg Scenario: A wifi client gets connected to an access point which inturn is connected to the switch, the mac address of the client shows up in the switch table. However if the client is disconnected, the client's mac address would still be displayed in the switch table )

View 9 Replies View Related

Cisco Switching/Routing :: 3550 / Access List - Block One Ip Or Port

Jan 9, 2012

I have a layer 3 switch, 3550.I have several vlans on there just for playing around with. One of the vlans, has a vonage linksys box attached to it with a UK number attached. From time to time telemarketers call at 03:00 in the morning, this as I'm sure you can imagine is not much fun. The linksys box gets 192.168.3.3 as it's ip.The switch is connected to a non cisco router at 192.168.0.1
 
interface FastEthernet0/24
no switchport
ip address 192.168.0.2 255.255.255.0
 
I was thinking a time based access list would work best I have tried several variations but the phone still rings. I have tried access-list 1 deny host 192.168.3.3 permit ..... and more extensive lists but the phone still rings. I have not applied the time-range yet, so that's not the problem.I have applied the list to the vlan interface and to fa0/24 but it's not working.

View 3 Replies View Related

Cisco Switching/Routing :: 3550 / Layer 3 Switch Not Routing?

Apr 26, 2012

I have a 3550 l3 switch configured as follows:

vlan 10 ports 1-10
vlan 21 ports 11-20
vlan 30 port 21-30
vlan 40 ports 31-40
default vlan should be vlan 21

I have the servers, switch and router connected to vlan 21.  Vlan 21 works great I can browse the internet, but I cannot ping any other vlans. router is connected to fa0/19
 
[code]
Building configuration... 
Current configuration : 4833 bytes
 !
 version 12.2
 no service pad

[code]....

View 11 Replies View Related

Cisco Switching/Routing :: VLan Routing Same Switch 3550-12T?

Mar 10, 2013

I'm having some problems setting up vlans to talk to each other on a 3550-12T switch. Its quite a simple setup I have, but I need to split my network up.
 
Currently I have a network of 192.168.25.0 255.255.255.0 I want to create a new vlan network of 192.168.30.0 255.255.255.0 So I have configured my vlan1 (default vlan) to have an ip of 192.168.25.250 for getting to the management page
 
I have created a vlan2 of 192.168.30.1 255.255.255.0 ?I have a port 10 linked to one of my 3560G's?In port 9 which is on vlan2 I have my pc plugged in with a static ip of 192.168.30.50 from the router I can ping any device on 192.168.25.x.
 
I can not ping 192.168.30.1 (which is my vlan2) nor can i ping the PC.
 
I have enabled ip routing  But I dont have a default route, this is becase we don't have a router on the network.

View 18 Replies View Related

Cisco Switching/Routing :: GLC-GE-100FX - Connection To 3550 Switch Over MMF

May 21, 2012

i have an OM1 MMF fiber run between two switches, the first being a 3750 and the second being a 3550.
 
The link currently exceeds the maximum distance for OM1 @ 1000Mb/s (220m) so i would like to downgrade the link to 100FX using the necessary SFP's/GBIC's to extend the maximum distance to 550m and run the link @ 100Mb/s.
 
I have the part code for the 100FX SFP to install in the 3750 (GLC-GE-100FX) but cant find a 100FX GBIC for the 3550, can I use a 1000SX GBIC (WS-G5484) for the 3550 at one end and the 100FX SFP at the other? Any success with this configuration over MMF?

View 3 Replies View Related

Cisco Switching/Routing :: 3550 Upgrade To Gigabit Switch

Jun 4, 2013

I have a 3550 switch right now, and need to upgrade to a gigabit switch, so I'm looking at a 3560G-48.  For some reason I purchased an EMI version of my 3550, but run the ipbase image...what I need to look for - is a 3560G-48-s good for what I need?

View 4 Replies View Related

Cisco Switching/Routing :: Port Unreachable Messages On 3550 Switch?

Jan 24, 2012

While working at a client site today, I was troubleshooting some ICMP connectivity for a network we have created.I turned on 'debug ip icmp" on the 3550 switch int he middle, and was inundated with the following debug output:
 
Jan 25 11:01:14.641: ICMP: dst (172.16.1.7) port unreachable rcv from 172.16.1.5
Jan 25 11:01:14.641: ICMP: dst (172.16.1.7) port unreachable rcv from 172.16.1.5
Jan 25 11:01:14.641: ICMP: dst (172.16.1.7) port unreachable rcv from 172.16.1.5
Jan 25 11:01:14.641: ICMP: dst (172.16.1.7) port unreachable rcv from 172.16.1.5

[code]....
 
This output fires several times a second, and based on how often it is firing, I am curious if it may be a culprit with respect to the fact that the client has indicated that they have some slow internet.Should the next step be to look at the workstation at 172.16.1.5? 

View 10 Replies View Related

Cisco Switching/Routing :: Route-map Command Support On Switch 3550?

Sep 30, 2012

I have cisco switch 3550 IOS Version 12.1(19)EA1c.   
 
I can configure route-map commands on that.  but i can not apply that into any vlan interface.   while i try to apply the following command ( ip policy route-map PBR) on VLAN int i get an error msg saying that the command is not recognized.

View 3 Replies View Related

Cisco Switching/Routing :: Have HSRP Or GLBP Between Two Different Switch Like 3550 And 3560?

Dec 9, 2012

Can i have HSRP or GLBP between two different switch like 3550 and 3560?

View 3 Replies View Related

Cisco Switching/Routing :: Catalyst 3550 Switch - Dynamic QoS Setup

Mar 28, 2012

I live in a condo building that uses 3 Cisco Catalyst 3550 switches connected to a Comcast router with 100 Mbps download. Currently we regulate bandwidth by providing each user with 3 Mbps download. Even if only two people are active they still only get 3 Mbps download. I would like to set it up so if two people are using they each get 50 Mbps; a sort of 'dynamic qos. Is this possible with these switches? Would we have to purchase a Cisco router in order to provide this feature?

View 9 Replies View Related

Cisco Switching/Routing :: Changing Native Vlan On 3550 Switch

Dec 22, 2012

I am having trouble after creating a management vlan (99) on a 3550 switch.I have configured the vlan (99) and given it an IP (192.168.1.100) and a default gateway (my router address - 192.168.1.99).I can ping to the switch from a PC and vice versa. The management VLAN IP is fine but now I cannot ping to the router from either the PC or the switch.It seems that just by adding VLAN 99 with it's own IP address has now prevented pings from the switch/ PC to the router ?Due to the fact that I have created a new switch management VLAN with an IP, does this mean I have set up the router as a 'router on a stick' scenario ? [code]

View 4 Replies View Related

Cisco Switching/Routing :: Enable / Disable Interfaces On 3550 Switch

Jul 14, 2012

I`m looking to automate some functions in a web application.Functions like enable/disable interfaces on a Cisco 3550 switch.

View 5 Replies View Related

Cisco Switching/Routing :: 3550 EMI Switch Is Not Responding To Power Connection

May 10, 2012

My cisco 3550 EMI switch is not responding to power connection. I have checked and changed power cable. its still not working.fan is not running and no lights on front panel

View 3 Replies View Related

Cisco Switching/Routing :: Internet Access For 3550 Switch VLANs?

Feb 22, 2012

I have a small cisco switch cluster (seven different 2924, 3524cisco switches) with 3550 as a cluster control which does all the inter vlan routing that works fine.
 
This cluster is in semi production PBX interop testing lab. This is a closed network without internet access and not connected to our corporate network.However now I have to add this capability so some equipment in the lab can get Microsoft updates over the internet.
 
I've created a port on a 3550 (fa0/19) and connected it to another network that has internet access. It picked an ip address and when I'm logged in to the 3550 I can ping hosts on the outside network. However I can't ping any hosts on that network from any hosts that are connected to my vlans.I've tried a few different things, but still can't make it to work.
 
Here is a short version of my 3550 configuration:

!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log datetime
no service password-encryption

[code]....

View 13 Replies View Related

Cisco Switching/Routing :: 3550 - Switch Disconnects Another Voip Phone?

May 14, 2013

im having this strange issue where everytime i plug in a voip phone to my 3550 the switch disconnects another voip phone.then to fix the disconnected phone (7940) i need to power off the phone 5-10 minutes then power it on again.

but the strange thing is, once i have to do that to fix the phone and connect the phone back to the switch, the port link is up, but no macs are seen on that port.

View 1 Replies View Related

Cisco Switching/Routing :: Switch 3550 - Command To Display GBIC In It?

Nov 9, 2011

Is there any command to display the GBIC in the switch because I need to replace 3550 but I have no exact part number

the model is WS-C3550-24-SMI
and try
sh inventory
sh hardware
sh diag
sh module

View 1 Replies View Related

Cisco Switching/Routing :: 3550 - Copy IOS To Switch In ROMmon Mode?

Jan 24, 2012

I have a 3550 switch that was replaced at a remote site with no IOS. This is a switch not a router so tftpdnld does not work.
 
[Code]...
 
The problem is the switches interface never comes up so try to connect to the tftp server. I read on google it can't be done on a switch to copy from tftp to flash in rommon mode on a switch and to use XMODEM. My problem is I do not have access to it, I ssh into a 3640 which is an access server for all devices and that is how I have console to it, how to use XMODEM over ssh.
 
But I'm fairly certain that there has to be a way to just copy it from tftp? I have a 3550 local and when I put it in rommon mode it stops the port check at port, port 1 goes from green when you plug it in to off then port 2 changes to amber and the rest green. So just by the look of this I would believe tftp would work; you just need to use port 1.

View 1 Replies View Related

Cisco Switching/Routing :: 3550 Switch - Software Forced Crash Exception

Feb 7, 2013

Our switch had a little crash-fest this morning at 2:30 AM. I did find a web page about diagnosing Software Forced Crash Exceptions, but it did not look like ours was one of the more easily-identifiable ones.
 
It may be worth noting that we've only used this switch for about a month, everything seemed fine until now. When we got the switch it did not have any GigE modules, and this week we put 2 into it and have been using them for 2 servers.
 
It looks like the switch was crashing repeatedly over a period of 20 minutes, and then it stopped and normalized. In the logs of the router that this switch uplinks into, we could see the ethernet port flapping during the time that the switch wasn't reachable.
 
Here's the Show Stack on the switch:
 
Sfld_3550#    show stackMinimum process stacks:Free/Size   Name4404/6000   vegas_flash init3352/6000   SaveCrashBuffer5716/6000   CDP BLOB8512/9000   IP Background5596/6000   vqpc_shim_create_addr_tbl5584/6000   SPAN Subsystem5552/6000   SASL MAIN4944/6000   vegas IPC process8704/9000   cdp init process5404/6000   RADIUS INITCONFIG4928/6000   Vegas CrashBuffer5664/6000   URPF stats2536/3000   Rom Random Update

[code].....

View 2 Replies View Related

Cisco Switching/Routing :: 3550 - Unable To Ping Internet From HSRP Standby Switch

Nov 16, 2011

I have router connected to 2  3550 switches  directly. 3550A  and B  switches are running HSRP. OSPF is running between Router and 2 switches.
 
From Switch B  i can ping the Router Wan interface but not the internet sites. from Switch A  i can ping any sites?
  
Switch B 
3550SMIB#                          sh ip routeCodes: C - connected, S - static, R - RIP, M - mobile, B - BGP       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area       N1

[Code]......

View 7 Replies View Related

Cisco Switching/Routing :: Router 2911 Blocking Single IP Address

Jan 29, 2013

We have a Cisco 2911 router in our company. I didn't set it up myself nor I was involved. I only started working here recently, bit over 3 months ago. I have been given ongoing task which other IT Technicians been struggling for almost a year with a idea that maybe because I'm fresh person in the company I will find a original idea why could this thing not work.
 
Our router have a problem with blocking a single IP address, but not completely  It's hard to explain but I will try my best. Company is hosting their website externally and accessing the host and FTP on the host on daily bases. It is important for the website to work on the internal network in company. It does work sometimes, but from time-to-time the website showing time-out error 118 on any point before Cisco router using both http and https, have tried putting just the IP address( doesn't matter is it on the general network or last ISA server on DMZ ). I am able to connect to the website using any of proxy gates but not directly to the website. I have also tested the connection past the router and I was able to connect to the website without any problems. I am also able to ping the host's address from the router and internal network.

I have eliminated the possibility of not correctly setup proxy or firewall on the network as problem also occur on the DMZ. I have also checked access-lists on the router and firewall rules for Any possibilities and I can't really see a way why would the router do this.

View 2 Replies View Related

Cisco Switching/Routing :: 6500 Single IP Bound To 2 Server Mac Address

Jun 11, 2013

I have 2 servers, one active, the other standby, both will be using the same IP. If the active fails then a re-patch for the standby to make this the active. I understand that i will need to clear the arp & maybe mac address table on the 6500 for the new active server to work, as the failed server will have its mac address on the 6500,.
 
is there a way around this so i dont have to clear the arp cache & clear the mac table? [code]

View 6 Replies View Related

Cisco Switching/Routing :: 3750X - Single Switch Stack?

Mar 8, 2012

I have a 3750X 24 port switch (with NM-1G network module) running IOS 15.0(1). Is there any benefit or reason to plug in the included Stack Wise cable and loop it back to itself in a single switch installation?
 
I don't see any recommendation in the documentation. The data sheet indicates a single switch is a non-blocking device so I'd think there's no bandwidth advantage like there is when connecting an actual multi-switch stack and needing to close the loop for the full 32 Gbps stack bandwidth.

View 2 Replies View Related

Cisco Switching/Routing :: 4500 - Single IP Address On Both Sides Of Port Channel

Feb 19, 2013

We have a single 4500 connecting to two non-cisco devices. We need to enable port channelling or link aggregation between these two.The links are carrying mulitple vlans , hence are trunked and the ip address on either side is used for routing.
 
From each of the two non-cisco device, i am taking 2 ports each to connect to the 4500.On each  non-cisco device side, two ports will bundle together as one aggregated interface (ae1) and the other will be called ae2.
 
my query is how do i do the configuration for etherchannel on the cisco 4500 side , as it will need two different Po's( port channels).I need a single ip address on both sides of port channel to be present for routing.

View 2 Replies View Related

Cisco Switching/Routing :: Multiple IP On Single Vlan In Cat 45xx Switch

Mar 12, 2012

I would like to know if it is possible to assign a 3rd IP address to my end user vlan. Basically the 45xx acts as my end user gateway and has been confirgured as below
 
interface VlanXX
description Main Vlan
ip address 2.X.X.X 255.255.255.0 secondary
ip address 1.X.X.X 255.255.252.0

[Code].....
 
Here, due to IP address exhaustion in my end-user network, i want to add one more subnet X.X.X.X/22 to my network and assign one IP more from this range to the above vlan to act as the gateway IP.

View 1 Replies View Related

Cisco Switching/Routing :: Clearing Single ARP Entry In 6500 Switch?

Feb 2, 2009

Is there any way to clear a single ARP cache entry on the 6500 switch ?

View 8 Replies View Related

Cisco Switching/Routing :: Creating Stack Of 2960s From Single Live Switch

Sep 23, 2012

I have a live 28port Catalyst 2960S switch. By live I mean that there is an essential piece of equipment plugged into this switch that can suffer little to no downtime. Over the course of time the number of devices patched into this location has increased to exceed the 24 ports available and we have had to resort to adding unmanaged switches to fill the need. We have acquired an additional 2960 & stacking modules that I would like to stack together, keeping the existing switch as the master. It is my understanding that the stacking modules are hot-swappable and that this member switch can be added without bringing the master switch down, thus creating zero down time for the financial server that is connected.
 
The steps I believe that need to be followed are as such: write mem to existing switch and backup to our TFTP serverinstall the stack module in the existing (while powered up) and new (while powered down)place the 2 redundant FlexStack link cables on both switchesthen simply power the member switch on After boot the member switch will get it's OS and configuration from the master and I can begin moving CAT5 cables from the unmanaged switches to the stack.

View 2 Replies View Related

Cisco Switching/Routing :: 1841 Need To Block MAC Address / Applied Command Access-list

Sep 4, 2012

I am using cisco 1841 LAN router, I need to block MAC address i have applied the command access-list 1102 deny 0000.0000.0000.0000 mac address..... but it does not work.

View 24 Replies View Related

Cisco Switching/Routing :: Configuring 1941 With 8 Port EHWic Switch Module And Onboard GE Ports In Single LAN?

Jul 1, 2012

Can you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?

I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?

View 2 Replies View Related

Cisco WAN :: Routing Between Routed Ports On A 3550 Switch

Aug 24, 2011

I have 2 3550's connected across a wireless link. [code] However, from Switch A, I cannot reach 10.1.3.9Can this 3550 not route traffic between 2 routed ports?

View 8 Replies View Related

Cisco Switching/Routing :: 3750 No MAC Address On Switch Port

Apr 15, 2012

There 's a Cisco IP phone that sits between a PC and the switch port. On the switch port, no MAC address is learned. However, the switch is able to detect the IP phone and deliver power to it: [code] Switch is Catalyst 3750 with IOS version  12.2(58)SE1.

View 1 Replies View Related

Cisco Switching/Routing :: Get MAC Address From Switch Ports With SNMP V3?

Feb 1, 2013

I have been reading the postings on this site trying to retrieve the MAC address for the client devices (computers, printers) attached to our switches.  We have approximately 500 switches and I need to map the mac address to the switch.  It appears the OID information is for SNMP v2.  We are restricted to using only SNMP v3.  I have tried using the Cisco SNMP Object Navigator without any success. 

View 2 Replies View Related

Cisco Switching/Routing :: Determine IP Address Of 2950 Switch?

Aug 13, 2012

Do they have a default IP assigned to them?
 
I'm trying to access the CMS administration page from my browser. I've already tried 192.168.0.1 and that brings up my gateway (cable modem from Time Warner).

View 15 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved