Cisco Switching/Routing :: 4500 - Single IP Address On Both Sides Of Port Channel
Feb 19, 2013
We have a single 4500 connecting to two non-cisco devices. We need to enable port channelling or link aggregation between these two.The links are carrying mulitple vlans , hence are trunked and the ip address on either side is used for routing.
From each of the two non-cisco device, i am taking 2 ports each to connect to the 4500.On each non-cisco device side, two ports will bundle together as one aggregated interface (ae1) and the other will be called ae2.
my query is how do i do the configuration for etherchannel on the cisco 4500 side , as it will need two different Po's( port channels).I need a single ip address on both sides of port channel to be present for routing.
View 2 Replies
ADVERTISEMENT
May 17, 2012
I configured the interfaces individually at L3 and could ping across each link Example:
4500 Switch 2: 6500 Switch 1
int t5/1 - int g3/17 1 Gig fiber link
tore down config
tried second set of interface
int t6/1 - int g8/17 1 Gig fiber link
Ping successful
[code]....
View 2 Replies
View Related
Mar 18, 2010
I am trying to implement priority queuing (LLQ) on a pair of 10GE links between a 4507 with Sup6E and a 4948 which are configured as an etherchannel. I am unable to configure a priority queue on the 4507. I am running into the following issues:
I want to have a priority queue for voice traffic and specify minimum bandwidth for a critical application. If I configure a class with the priority command it will not let me use the bandwidth command on another class unless the priority class is policed. If I try it without the police command I get the message "bandwidth kbps/percent command cannot co-exist with strict priority in the same policy-map ". If I add a police statement to the priority class then I don't get this error.
When I try to apply the resulting service-policy to the physical interface it says "% A service-policy with non-queuing actions should be attached to the port-channel associated with this physical port" and does not add the command to the config.
If I try to associate the same policy-map to the port-channel rather than the physical interface it says "% A service-policy with queuing actions can be attached in output direction only on physical ports" and does not add the command to the config.
All of the other interfaces on the 4500 are working OK. The trunks have auto qos voip trust configured and access ports are marking the critical application traffic.
The 4507 is running 12.2(44)SG1 EnterpriseK9. I don't have the luxury to upgrade blindly to fix the problem unless I can identify a specific bug that is causing the problem.
View 5 Replies
View Related
Apr 24, 2012
In mucking around with my 4500 I accidently deleted the ip address that I use to get into it with telnet and CNA. I have a console cable hooked up to and I'm in that way but the commands I got off the internet did not work. Those commands were set interface sc0 10.x.x.x/xx and set interface me1 10.x.x.x/xx. It didn't like interface and I notices when I did a set ?
View 6 Replies
View Related
Sep 12, 2012
Have 2 N2K with dual-connections to both 2 N5K, will all 4-ports of N5K will be the same port-channel. N2K as well ?
View 1 Replies
View Related
Nov 29, 2011
I need to configure a port channel between two sw 4507R. with port Giga, but those port are in different modules.
Sw-1
interface GigabitEthernet5/48
description **** Conexion Switch-2*****
[Code].....
View 2 Replies
View Related
Dec 19, 2012
We want to filter IP traffic by MAC address on Catalyst 4500. Since we are using bonding (active-backup mode) we need those mac addresses appear on different ports. Below are solutions that we have tried: ACL but it does not work since mac acls only match non ip traffic (We CAN NOT use ip acl). Use a static mac address-table entry to ALLOW specific mac addresses. It does not work either since the same MAC address needs to be seen on a different port. Catalyst 4500 does not support auto-learn option (as e.g. Nexus 5000).
View 3 Replies
View Related
Dec 7, 2011
I have 3750 core/distribution switches with routing enabled in two offices connected with copper link and L3 port channel interfaces. NewOffice#2 has moved about 5 miles farther away from office#1 and I have to deploy new core/distribution switch connect it to old core#2 via F.O and move all access switches with it. Old core will stay in old #2 offices as a bridge between office#1 and new office#2 Office#1core<->copper (Ethernet) <->oldoffice#2core<->f.o. <->new office#2core How I should configure port channels ports on oldoffice#2 core to act as bridge between office#1 core/dist and newoffice#2 core/dist without changing anything else (ip, etc) on whole network
View 1 Replies
View Related
Apr 22, 2012
I have 2 Cisco 6509 switches linked together via single Fibre as a trunk.I want to change this to a port channel where I will add another 3 fibre ports to the port channel but what order do I do this to minimise any disruption.
1-Configure PortChannel and add the 3 new ports, this will bring up the Port Channel but what effect will this have on traffic currently going over the single Trunk link? Will spanning tree go mad, how will switches react?
2-Convert existing Trunk link to Portchannel then add in new ports to PortChannel, I guess in doing this there will be a small hit on traffic as it changes to a port channel.
View 2 Replies
View Related
Feb 24, 2012
We have 2 6513's that are linked via 2 10 gig interfaces, using an LACP channel.I received an alert this aft stating that the far 6513 was unreachable and the port channel int PO3 had gone down, the 2 10 gig interfaces had also gone down on either side. 5 mins later PO3 had resestablished itself and has been fine since. [code]
View 4 Replies
View Related
Feb 7, 2013
We are running nexus 5018 in our DC.What is the difference betwen "channel-group 214 mode active" and " channel-group 216" Any difference?.. because i have problem with this config we are going build a server config?
We have problem with porth channel down.
5K# sh int po71
port-channel71 is down (No operational members)
vPC Status: Down, vPC number: 71 [packets forwarded via vPC peer-link]
View 1 Replies
View Related
Jan 22, 2012
I set up a port-channel trunk between a acess switch 3750 ( int gi2/0/1 and gi2/0/2) and Core 6509( int gi7/11 and gi7/12).
On the both the 3750& 6509 I configured:
interface Port-channel15
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 100,103
switchport mode trunk
But the ports on the core g7/11 and g7/12 keep shutdown and when I do show interfaces port-channel 15, it show the interface is shutdown.
View 6 Replies
View Related
May 8, 2011
My Catalayst 4507 is reaching up to 82% CPU utilization and I noticed that K2L2 Address Table R is causing the high CPU.
C4507#sh processes cpu | in HiPri|LoPri|CPU utilizationCPU utilization for five seconds: 82%/1%; one minute: 86%; five minutes: 87% 54 350533923 329104616 1065 13.27% 13.84% 13.86% 0 Cat4k Mgmt HiPri 55 1771768520 274992685 6442 59.91% 64.55% 66.04% 0 Cat4k Mgmt LoPri
C4507#sh platform health | in K2L2|%CPuK2L2 Address Table R 2.00 66.35 12 5 100 500 91 82 58 27272:55K2L2 New Static Addr 2.00 0.00 10 0 100 500 0 0 0 0:00K2L2 New Multicast A 2.00 0.00 10 5 100 500 0 0 0 0:18K2L2 Dynamic Address 2.00 0.00 10 5 100 500 0 0 0 0:16K2L2 Vlan Table Revi 2.00 0.00 12 8 100 500 0 0 0 1:22
View 2 Replies
View Related
Sep 3, 2012
Most of the 4500 Switches in our network are giving the similar error for so many ports
%C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 1 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on p t Gi2/6 in vlan 100
Its impossible to do a wireshark packet tracing for all the ports.
View 2 Replies
View Related
Nov 14, 2012
i just want to ask whether i should do some configurations or not on my cisco switch 4500 L3 regarding the error of 500 invalid port command when host try to access FTP active on to FTP server, i just did static route on gig interface with no switchport mode to that host network, all traffic type was allowed except the FTP with active mode?
View 7 Replies
View Related
Feb 27, 2013
I am building a new network and intended on using the min-link feature on my port-channels between a 3750-X series switch and Nexus 4k.
However reading further into this it seems this feature is only supported on higher end models. I cannot find any reference to the min-links feature in the 3750-X configuration guide. Is this an available feature?
The 3750-X model is WS-C3750X-24T-L running IOS 12.2(55)SE3 IP Services
My thoughts is that the is only an LACP supported feature so I may not see the command until I have entered an LACP specific command on the port-channel but unfortunately I do not have a 3750X to verify this on at present.
View 0 Replies
View Related
Jan 17, 2012
We have one 3825 router used as voice gateway. For redudancy, we want to connect it to two different switches which has STP and HSRP running. Can I create a port-channel with two Giga interfaces in 3825 and connect to two different switches? Should I configure port channel in switch with only one port in each port-channel? I know server can be connected to different switches with NIC teaming. I just want to mimic that kind of setup. I did one time for port-channel in 3825, but it was connected to a stacked 3750X. So it's different case now.
View 2 Replies
View Related
May 8, 2013
I am trying to configure port-channel from one switch to two switchs, and only one interface of each switches make part of the port channel.Cisco IOS Software, ME380x Software (ME380x-UNIVERSALK9-M), Version 12.2(52)EY4, RELEASE SOFTWARE (fc1) [code]
View 5 Replies
View Related
Jan 22, 2012
I have a pair of 6500's setup with VSS and there is currently only one link between then. However one end of the link is on Po10 and the other end is on Po25. If I move the Po25 over to Po10, will things break? It seems to be working fine now. I'm about to add a second link and I'm concerned about the current configuration. It makes more sense to me to have both ends of the same link on the same port-channel ID. I've seen documentation which states otherwise however.
interface Port-channel10
no switchport
no ip address
[Code]....
View 2 Replies
View Related
Mar 3, 2012
I am using 3560.IP rouitng is being turned off on this.Curious to know if I will create etherchannel or port channel.I think etherchannel.Correct me if I am wrong.On connecting switches I have vlan10,20,30 to be allowed.I am sure I need to allow these all vlan in 10,20,30 which are on the trunk port on each side switch.Post that will add channel-port lacp and make it in active mode.Is that correct.This way traffic will be load-balanced/aggregated on minimum 2 ports who are the part of this.
View 2 Replies
View Related
Jan 27, 2013
Here's what I'm trying to do. We are having new storage servers installed that will be using NFS. I'm being told that they need to have their connections port channeled. Right now, the servers have connections to 2 different 3750s for HA. Is it possible to configure a port channel between these 2 connections?
View 4 Replies
View Related
Apr 15, 2013
I have an inquiry about a configuration I deploy in a C2960 switch. I have configured a ether channel with 8 ports, the load balanced method is source mac address. The bundling protocol is LACP.
I have found the ether channel is not balanced as I expect. One of the eight interfaces is congested.
Code...
View 2 Replies
View Related
May 13, 2012
We have a switch that, when configuring auto qos on and edge port facing video equipment, the upstream port channel drops. I was wondering if no auto qos would have to be configured on the member ports of the port channel prior to enabling auto qos on any other ports.
View 2 Replies
View Related
Oct 30, 2011
I have a Cisco 6500 series switch with VS-C6509E-S720-10G ,I have two redundant supervisors between two chassis on the LAN with no add-on line cards ?
I need to know if I can use the redundant supervisor 10 Gb uplinks to form a layer-2 Port channel between the two 6500 switches as i do not want to use want to keep the port idle additionally I need more bandwidth between the two switches for my server farm?
View 1 Replies
View Related
Apr 3, 2012
I have 2 cisco 6500 in a VSS configuration , All of my Lan access switches are Stack switches and every Stack is connected to the VSS in a Port-channel so basically this is a loop free environment with no blocked ports .As a best practice I left STP in the Background (mstp)which enhanced cisco features to STP should I configure on the Aggregator (6500-VSS) and on the Access switches ?
Because of my topology I dont see the need in configuring most features like Uplink Fast and Backbone Fast but I have configured Loop Guard in addition to UDLD on the 6500 Aggregation Switches (on the port-channels).On the access ports I have configured portfast , bpduguard and guard root (seems a little pointless to configure the two...)
1.should I Leave UDLD on and get rid of LoopGuard and configure Guard root instead ? since LoopGuard cannot be configured with Guard Root.
2.should I configure GuardRoot on access ports if I already have BpduGuard on them ?
3.Is there anything I need to configure on the physicall interface or is everything configured on the port-channel since STP reguards port- channel as a single interface ?
View 4 Replies
View Related
May 9, 2012
I am trying to create a port channel between HP servers (4 nic) and two nexus 2k. The server side its a single team with 803.2ad fault taulerence and on the nexus side it have created two port channel (port channel 1 for nexus 2k1 and port channel 2 for nexus 2k2) and made them ACTIVE (channel group mode active)
But when i add a another server on different ports and port channel them the same way as the above server on nexus 2k1 and nexus 2k2, the first server stops pinging. so i have to sht down the first port channel and reopen them - then it works, however it says NO NETWORK ACCESS on the servers (running windows 2008). the only way is to reboot the server i cant be doing this on a production network.
View 6 Replies
View Related
Apr 23, 2012
I would like to know how many port channel can i configured in the switch 3750 X ? and if there is a limitation by IOS ?
View 4 Replies
View Related
Nov 16, 2011
I need to block this mac address in my 3550 switch.i enable port security but this mac address comes and do the violation and port is shut down.
View 3 Replies
View Related
Jan 29, 2013
We have a Cisco 2911 router in our company. I didn't set it up myself nor I was involved. I only started working here recently, bit over 3 months ago. I have been given ongoing task which other IT Technicians been struggling for almost a year with a idea that maybe because I'm fresh person in the company I will find a original idea why could this thing not work.
Our router have a problem with blocking a single IP address, but not completely It's hard to explain but I will try my best. Company is hosting their website externally and accessing the host and FTP on the host on daily bases. It is important for the website to work on the internal network in company. It does work sometimes, but from time-to-time the website showing time-out error 118 on any point before Cisco router using both http and https, have tried putting just the IP address( doesn't matter is it on the general network or last ISA server on DMZ ). I am able to connect to the website using any of proxy gates but not directly to the website. I have also tested the connection past the router and I was able to connect to the website without any problems. I am also able to ping the host's address from the router and internal network.
I have eliminated the possibility of not correctly setup proxy or firewall on the network as problem also occur on the DMZ. I have also checked access-lists on the router and firewall rules for Any possibilities and I can't really see a way why would the router do this.
View 2 Replies
View Related
Jun 11, 2013
I have 2 servers, one active, the other standby, both will be using the same IP. If the active fails then a re-patch for the standby to make this the active. I understand that i will need to clear the arp & maybe mac address table on the 6500 for the new active server to work, as the failed server will have its mac address on the 6500,.
is there a way around this so i dont have to clear the arp cache & clear the mac table? [code]
View 6 Replies
View Related
Jun 28, 2012
is there a way to show the last time a port was active/inactive on a catalyst 4500?
View 3 Replies
View Related
Apr 24, 2011
On a 4500 switch port , defined as access vlan 10, if the user connects his own dhcp server ( instead of the normal pc that should be connected ), will it cause issues with my existing network. the existing network is all static ip. In above case, will the dhcp server start looking out and assign dhcp ip's , if a user unknowingly removes his static ip and changes to obtain ip via dhcp option on the lan properties.
View 10 Replies
View Related
Mar 27, 2013
On 45XX catalyst , bandwidth is allocated across six 8-port groups, providing 1 Gbps per port group. Example for the following line card : WS-X4448-GB-SFP
I want to know if there is the same mecanism on 3750X switches. I mean is bandwidth allocated across a group of ports like on 4500 catalyst ?
View 5 Replies
View Related
