Cisco Switching/Routing :: Command To Verify MDIX On 2960S Switch?
May 9, 2012I config mdix on port gi1/0/7 as mdix auto IT does not show in running config.Is there any way or command which i can use to verify mdix on port?
View 2 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 2960s / Add One More Switch In Stack?
Apr 29, 2013I have a running setup having 2 Cisco 2960s 24 TS switch with Stack configuration. Now I want to add one more same Cisco switch. My questions are:-
1) How can I do this...(Should follow the same process as I did before.
2) Could I do this without impacting the service. i.e. without rebooting the switch.
3) What should be the connection archiecture as of now since there is two switch so it is connected 1 -1 and 2-2. but for 3 switch should we require to change the connectivity.
Cisco Switching/Routing :: Information About PoE Of Switch 2960S
Jan 21, 2013I use the Switch 2960S support PoE and 10 access points cisco.I have one more question:
-- If all 10 access points cisco use copper cable to connect to 2960S, 5 access points use power adapter and 5 access points use power from Switch. How Switch 2960S will provide power for 10 AP or switch 2960S will understand and only provide power for 5 APs?
Cisco Switching/Routing :: What Is The Use Of No Switch Port Command In L3 Switch
Dec 28, 2008what is the use of no switch port command in L3 switch?
View 7 Replies View RelatedCisco Switching/Routing :: IOS Upgrade Option In 2960S Switch
Dec 11, 2012We have a Cat2960-S Series PoE+ currently running 12.2(55) SE5 ios with SW image C2960S-UNIVERSALK9-M.We want to upgrade the ios to the lastest version but found there are 2 version: 12.2(53) SE2 and 15.0(1) SE.Which is the best & suitable for upgrade?
View 3 Replies View RelatedCisco Switching/Routing :: 2960s Switch Stack IOS Upgrade?
Apr 18, 2012I was just curious about something with upgrading a 2960s stack.
To copy the image to the switches in the stack I use: Switch# archive download-sw tftp://x.x.x.x/filename
Does this also set the image as the boot image or do I still need to issue the boot system flash command?
can I just issue this command on the master switch and reload and the new config will be pushed to the rest of the switches?
Cisco Switching/Routing :: Switch 2960S Did Not Configure Username
Jun 5, 2013After i have already configured my cisco switch 2960 , i configured my console as the below [code] after i reboot my switch , i found that the switch asked me for username . However i did not configure username , how can i solve this problem , without password reset . I have already configured 15 switch , 100% this problem will be in all switches.
View 19 Replies View RelatedCisco Switching/Routing :: Configure VLAN On 2960S Switch
Jan 20, 2013I have hybrid network in which I want to configure VLAN on Cisco 2960 S switch. I have unmanged switch where my DHCP server and other servers are connected. Now I created two VLANs on cisco 2960S and they don't talk each other, but as soon as I connect unmanaged switch to 2960S switch, both VLANs start communicating which I don't want. I want to listen server traffic from unmanaged switch from both VLANs but simultaneously I don't want to communication between two VLANs.
View 10 Replies View RelatedCisco Switching/Routing :: Enabled Syslog On 2960S Switch
Oct 3, 2012I have enabled syslog on my Cisco 2960S swtich as shown below -
-logging facility local6
-logging host 10.11.12.122 transport tcp port 514
I have sent the port to TCP since that is what is configured on the SYSLOG server which is a CENTOS 5.8, running rsyslogd.I have tested the rsyslogd locally and it work.However i want to send any and all log messages in the buffer to my syslog server and it is not working.there is no firewall on the CENTOS and the ASA firewall filter is enabled for outgoing traffic.
Cisco Switching/Routing :: 2960s - Unable To Access Lite Switch
Nov 9, 2012Unable to access switch from outside the local network. Can get to all routers and PC's
View 2 Replies View RelatedCisco Switching/Routing :: 2960S Unable To Connect To Core Switch
Sep 21, 2012I have a problem with extending the LAN on a client site . They are looking to extend the LAN with a 2960S-series switch. Already in place is a 4510 switch which the 2960 is connected to via fibre. The 2 switches are both set up but there is no connectivity as I cant ping between them or anything. The management VLAN on the 2960 shows line up, protocol down, which I believe means the VLAN is enabled but there is a form of physical mismtach on the ports. I have attached the configs of both switches. I feel it might be a problem with GBIC module compatibility. The SFP installed on both ends of the switch are GLC-SX-MMD. On the 4510, the SFP sits in a twingig converter (CVR-X2-SFP) but there is no light on it at all when the cables are plugged in.
View 40 Replies View RelatedCisco Switching/Routing :: 2960S Replace Master Switch In Stack
Jun 4, 2012I have a stack of 2960S (c2960s-universalk9-mz.122-55.SE2.bin) and the master has failed (used to have a priority of 14). The second switch has become master (priority 1) as can be seen below: [code]
If I connect a new blank 2960S (same IOS) through the stack ports, will the master sync its config to the new one without causing problems?As I understand the new blank switch will also have a priority of 1 and will by default be numbered as 1. So if the config is correctly synced and I later on want to make switch 1 the master, I need to set the priority: [code]
Cisco Switching/Routing :: Creating Stack Of 2960s From Single Live Switch
Sep 23, 2012I have a live 28port Catalyst 2960S switch. By live I mean that there is an essential piece of equipment plugged into this switch that can suffer little to no downtime. Over the course of time the number of devices patched into this location has increased to exceed the 24 ports available and we have had to resort to adding unmanaged switches to fill the need. We have acquired an additional 2960 & stacking modules that I would like to stack together, keeping the existing switch as the master. It is my understanding that the stacking modules are hot-swappable and that this member switch can be added without bringing the master switch down, thus creating zero down time for the financial server that is connected.
The steps I believe that need to be followed are as such: write mem to existing switch and backup to our TFTP serverinstall the stack module in the existing (while powered up) and new (while powered down)place the 2 redundant FlexStack link cables on both switchesthen simply power the member switch on After boot the member switch will get it's OS and configuration from the master and I can begin moving CAT5 cables from the unmanaged switches to the stack.
Cisco Switching/Routing :: 2960S Packet Loss Is Minimal If A Switch Fails
Apr 11, 2012I have a Cisco 2960S stack and I'd like to tune the timers so that packet loss is minimal if a switch fails.To simulate a failed switch I have reloaded it while running a continuous ping to a management address on the stack's SVI: [code] As I see the same results when a ping is directed through the single switch (switched), and through the firewall (routed), I'm inclined to think that this is due to the stack failover timers on the Catalyst 2960S.Is it possible to change the stack failover timers (i.e hold down, failover etc), to speed up the failover process?
View 1 Replies View RelatedCisco Switching/Routing :: Cannot Uplink - Daisy Chain 2960S Series Switch To 3750
Feb 5, 2012I have a new Cisco 2960 S series switch with a basic configuration that needs to be uplinked or daisy chained to a Cisco 3750 switch. I am not getting any connectivity to the network with either a straight through or crossover cable. the port remains in amber but a 'show interface' indicates that the interface is up. I can manage the switch with a PC patched into any port on the switch with a static IP address. Must be something very simple that I am missing. Outlined below is the configuration.
Refresh_SW1#sh ver
Cisco IOS Software, C2960S Software (C2960S-UNIVERSALK9-M), Version 12.2(55)SE3,
RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code].....
Cisco :: Prime LMS 4.2 Command To Verify Installation
Feb 12, 2013I have installed Cisco Prime LMS 4.2 via OVA image with Linux Kernal. Is there any command or set of commands so that i can verfiy the installation are done correctly except show application.
View 1 Replies View RelatedCisco Switching/Routing :: Cat 3560 No Switchport Command Test Out Routing With Switch
Dec 8, 2011The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
Cisco WAN :: Hardware Command To Verify Nexus 5020
Apr 23, 2013What is the correct command to check the hardware of a Nexus 5020, like the show Inventori, show diag etc Used the same or is there a specific one for these items?
View 2 Replies View RelatedCisco Switching/Routing :: 6506E Switch Command Meaning
Feb 5, 2012I see the command "vlan access-log ratelimit 2000" and wonder what it is that it does.
View 2 Replies View RelatedCisco Switching/Routing :: Route-map Command Support On Switch 3550?
Sep 30, 2012I have cisco switch 3550 IOS Version 12.1(19)EA1c.
I can configure route-map commands on that. but i can not apply that into any vlan interface. while i try to apply the following command ( ip policy route-map PBR) on VLAN int i get an error msg saying that the command is not recognized.
Cisco Switching/Routing :: 7018 Is VPC Peer-switch Command Intrusive
Apr 3, 2012I need to enable vPC "peer-switch" command on a pair of Nexus 7018s which are currently vPC peers (primary and secondary). The STP root and Secondary root are currently configured across these switches.Can I enable the peer-switch command in this configuration without impacting services, and then modify both switches to have the same bridge priority without impacting services ? We have a few downstream 5ks which are not dual homed to both vPC peers (work in progress) so need to understand if the peer-switch command will in any way break this connectivity for now.
View 1 Replies View RelatedCisco Switching/Routing :: Command To Debug Packets On 3750 Switch
Apr 18, 2012What other command can be used to debug packets on a 3750 switch ?
View 2 Replies View RelatedCisco Switching/Routing :: Switch 3550 - Command To Display GBIC In It?
Nov 9, 2011Is there any command to display the GBIC in the switch because I need to replace 3550 but I have no exact part number
the model is WS-C3550-24-SMI
and try
sh inventory
sh hardware
sh diag
sh module
Cisco Switching/Routing :: (no Shutdown) Command Is Not Working In 2970 Switch Port
Apr 9, 2013a switch port is shutdown, but when i use NO SHUTDOWN command it is working and shows administratively down. like this command does not affect on it. i should enable this port? what can i do btw, port is not in errdisable and portfast is enabled.
View 3 Replies View RelatedCisco Switching/Routing :: Copy Flash Tftp Command Failed On 3750 Switch
Oct 5, 2010I have a cisco 3750 swicth which i want to load a new ios to but unfortunately there's no enough space on the flash. This means that i need to backup the cureent (old) ios to my tftp server but the command keeps failing. It always gives 'No such file or directory' error .The free space on the flash is 8mb and my new ios is about 11mb.I also went inside the directory where the old is and inputed the same copy command but to no avail.Below are some of the command failure on the swicth:
[code]....
Cisco Switching/Routing :: 3560G 15.0(2)SE - Show Platform Forward Command Crashes Switch?
Dec 5, 2012I have been working on some Catalyst 3750's running 12.2(55)SE6 and hit an issue with CEF load-balancing over multiple equal-cost paths. Anyway this issue is now solved but it introduced me to the command 'show platform forward' - this shows you how the forwarding of a packet would be done via hardware cef (as opposed to the command 'sho ip cef exact-route' command that only shows the software cef path). Anyway I tried the command on a 3560G running 15.0(2)SE and it crashes the switch. I tried it a couple of times and verified that the MAC & IP addresses were exactly right in the command and each time the switch crashes. I have extracted the relevant bits from the crashinfo and attached them.
View 3 Replies View RelatedCisco Switching/Routing :: 6509 Core Switch Command / IP PIM Sparse-dense-mode
Oct 23, 2011What is PIM? give me an example when I will use and not use the PIM command.
View 4 Replies View RelatedCisco Switching/Routing :: 3560 Policy Based Routing Verify-availability
Apr 19, 2012Cisco 3560 does not support "set ip next-hop verify-availabilty". I need this command in my config. "set ip next-hop" do not do the same job.
View 8 Replies View RelatedCisco Switching/Routing :: WS-C6513 Command To Check 6500 Switch Performance / Resource Usage
Apr 25, 2013I am on a call right now troubleshooting some latency issue. The CPU usage on the sup card is low. Don't see any drops or input errors. I am aware that the switch and its modules have capability limits. Is there command I can run which will tell me if any module is overloaded or if the fabric/backplane is over utilized?My chassis is WS-C6513 and sup card is WS-SUP720-3B.
View 3 Replies View RelatedCisco Switching/Routing :: 3750 Switch - Eigrp Stub Static Redistributed Command Executable?
Feb 29, 2012On 3750 switch with IOS c3750-ipbasek9-mz.122-55.SE4.bin "eigrp stub static redistributed" command will be executable ?
View 1 Replies View RelatedCisco Switching/Routing :: Switch Port Auto-state Exclude Command Not Working In 4500
Jun 3, 2013I have configured a SVI in my 4500 ( Sup 7-E 10GE,,,,,,and,,,,,cat4500e-universalk9.SPA.03.02.00.SG.150-2.SG.bin) switch and it is showing Down Down, because there were no active switch port in the vlan, I added one switch port to this vlan but this port also in the down state, so i added the SWITCH PORT AUTO STATE EXCLUDE command under this port, even after this also the SVI never came up, So i added one systen to the port so both the switch port and the SVI came up...So why SWITCH PORT AUTO STATE EXCLUDE command have no effect in this model of the switch..
View 4 Replies View RelatedCisco Switching/Routing :: 4900 - How To Verify Link Before VLAN Extension
Mar 23, 2012we got a dark fiber betwwen two sites away from each other 30 Km,i need to connect this sites acts as backup dc to main dc in main site using cisco 4900 Switches in BK-DC anf 6513 in the main site,how can i verfiy if this fiber oparates as L2 and i can extend vlan servers,is it via "sh cdp neigh" and "sh vlan br"?
View 2 Replies View RelatedCisco Switches :: Ip Routing Command On SG300 Switch?
Feb 8, 2013What does "ip routing" do on the CLI on the SG300? When I do this, I see it enables ip forwarding, but there is no mention of this in the CLI manual. I'm just trying to figure out what I would use this for, and if I should leave it enabled, or disable it. I have several different SG300 switches in L3 mode, and they are set up in a multi-vlan environment...
View 2 Replies View Related