Cisco Switching/Routing :: Cat 6500 Sup 2t TCAM Counter Show Command?
Sep 26, 2012Any command similar to sup720 "show tcam counters" It doesn't work on Sup2t.....
View 2 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 6500 - Show Platform Port-asic Stats Drop Command?
Feb 21, 2012On a 3750 you can do a show platform port-asic stats drop command. Is there a corresponding command for 6500 chassis?
View 7 Replies View RelatedCisco Switching/Routing :: 6500 - WS-X6K-SUP2-2GE - TCAM Exhaustion?
Nov 11, 2012we have a WS-X6K-SUP2-2GE running CATOS software, we are facing a TCAM exhaustion.I would like to know the following:
1. during an exhaustion, based on what ACLs will be kept in hardware or moved to software? the name or number gives any precedence to an ACL over another ACL?
2. If the TCAM's utilisation was on the limit and we increased ACEs to a specific ACL, all the ACL will be moved to software or only the new entries?
Cisco :: Snmp Oids For Command Show Counters Interface Intx / Y Delta On Catalyst 6500
May 23, 2011I have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..Is possible to get these values using SNMP?
View 3 Replies View RelatedCisco Switching/Routing :: Show Command In ASR 1004 For Running Diagnostics
Aug 29, 2012is there a command available to run diagnostics in ASR port/SPA? the one below is from a juniper remote device. i was only able to find 'test interface' but haven't run this yet (currently in production).
View 5 Replies View RelatedCisco Switching/Routing :: Command To Show Physical Connection In 3660
Jun 19, 2012I am using cisco c3660 to act as Terminal Server for the communication of production machines in my company, recently there is a communication lost issue happen and its due to physical cable unplug from the machine. to troubleshoot for this issues i have to physically go inside my production area to check on it, as i understand from vendor we can check on the physical machine to see whether the LED light on the module is green or not, but in case of need to troubleshoot at night time, its time consuming as i need to travel back to company. is there any command that i can issue in the router c3660 to check on the physical connection between c3660 router and the production machine? the IOS version is IOS (tm) 3600 Software (C3660-I-M), Version 12.1(4)
View 3 Replies View RelatedCisco Switching/Routing :: Nexus 7000 SWACT Show Redundancy Command
Nov 9, 2012We have Nexus 7K recently installed few months back with 2 Sup (Slot 5 & Slot 6).Recently recevied mesaanges in monitoring servervia SNMP:Alarm : active unit removal caused an auto SWACT However, when checked there are no recent logs which may be linked to this alarm. The show redundancy command output shows that Sup in slot 5 is active which in slot 6 is Hot Standby.
View 1 Replies View RelatedCisco Switching/Routing :: C2960 Password-recovery Status Show Command
Feb 9, 2012I enabled the "no service password-recovery" command on my C2960 switch. All seems to work as discribed. Only issue I have is --- which show command is used to reveal if the password-recovery feature is enabled of disabled as the command doesn't show up in the running config after you enable it ?
NOTE: The command does show up in the C2960 switch in config t mode (unlike the IOS router 2800 series), but doesn't show up in the running-config after you enable or disable it.
On the 2800 series routers (latest IOS) in config t mode the command does not show up but if you type "no service passowrd-recovery" the command function correctly and it does list it in the running configuration.
Cisco Switching/Routing :: Equivalent Command To Show Int Summary On The Nexus 7000?
Nov 20, 2011tell me if there is an equivalent command to Show int Summary on the Nexus 7000?
eg
MYCISCOSW01#show int summary
*: interface is upIHQ: pkts in input hold queue IQD: pkts dropped from input queueOHQ: pkts in output hold queue OQD: pkts dropped from output queueRXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)TRTL: throttle count
[code]....
I find it a useful command on the 6500 to spot high traffic flows.
Cisco Switching/Routing :: Show IOS Logging Command When Catalyst 2960 Was Shut Down
Mar 29, 2012know Cisco IOS command, how to show when Catalyst 2960 was shut down (power off)?
View 2 Replies View RelatedCisco Switching/Routing :: 3560G 15.0(2)SE - Show Platform Forward Command Crashes Switch?
Dec 5, 2012I have been working on some Catalyst 3750's running 12.2(55)SE6 and hit an issue with CEF load-balancing over multiple equal-cost paths. Anyway this issue is now solved but it introduced me to the command 'show platform forward' - this shows you how the forwarding of a packet would be done via hardware cef (as opposed to the command 'sho ip cef exact-route' command that only shows the software cef path). Anyway I tried the command on a 3560G running 15.0(2)SE and it crashes the switch. I tried it a couple of times and verified that the MAC & IP addresses were exactly right in the command and each time the switch crashes. I have extracted the relevant bits from the crashinfo and attached them.
View 3 Replies View RelatedCisco Switching/Routing :: 6500 - Show Platform Capture ELAM Asic
May 29, 2012I know that an ELAM can be setup on a 6500 running ipservices 12.2(33)SXJ, however I noticed that following commands are not available on a 6500 router running advipservices 12.2(33)SXJ:show platform capture elam asic etc
So I wanted to know if there is an alternate way to setup an ELAM for troubleshooting purposes?
Cisco Switching/Routing :: 6500 Show Interface Status Output As VLAN
Mar 5, 2013I have a really weired thing happening on 6509 device with one of my customers.The device has a SUP 2 (MSFC2) with version 12.2.18SXF17B.
any VLAN interface once administratively down or simply down shows on "show interface status" output as VLAN.While it supposed to show "Routed". However once the port is up it is shows "routed" like it should.
Cisco Switching/Routing :: 6500 MSFC No IP Routing Command
Jun 2, 2012I used to "ip routing" command in order to enable inter-vlan routing, for example with 3750 cisco. I have a 6503 cisco with SUP720 MSFC3. I was able to create some vlans but I can not configure inter-vlan routing.
sw#conf t
Enter configuration commands, one per line. End with CNTL/Z.
swsur(config)#ip routing
[Code]....
Cisco Switching/Routing :: IP Routing Command In 6500?
Mar 16, 2013Where is the "ip routing" command in Cisco switch 6500 series?
is the ip routing enable by default accoridng to the: [URL]
Cisco Switching/Routing :: 6500 Clarification For Using Mac-address-table Synchronize Command
Jul 12, 2010We want to configure the "mac-address-table synchronize" command on our 6500 series switches to ensure that the CAM tables on our DFCs are in synch with the PFC on the supervisor modules. url...it is recommended that we disable the routed MAC purging with the mac-address-table aging-time 0 routed-mac global configuration command. What is a routed mac entry? Are there any issues with running that mac aging-time command?
We also plan to run this command "mac-address-table aging-time 14400" to keep our ARP and CAM tables on the same aging time to reduce unicast flooding on our network. Can we run this command with the "routed-mac" command above?
Cisco Switching/Routing :: WS-C6513 Command To Check 6500 Switch Performance / Resource Usage
Apr 25, 2013I am on a call right now troubleshooting some latency issue. The CPU usage on the sup card is low. Don't see any drops or input errors. I am aware that the switch and its modules have capability limits. Is there command I can run which will tell me if any module is overloaded or if the fabric/backplane is over utilized?My chassis is WS-C6513 and sup card is WS-SUP720-3B.
View 3 Replies View RelatedCisco Switching/Routing :: Output Discard Interface Counter In Nexus2000
Dec 6, 2012reasons for increasing "Output Discard” Interface Counter in Nexus2000 . ????
View 2 Replies View RelatedCisco Switching/Routing :: Tcam Utilization With 784
Apr 16, 2013I'd like to know what is "masks" in the output of show platform tcam utilization. What does 784 mean? What effect has the number of mask in the amount of supported unicast direct routes?
I'm having trouble comparing the capacity of theese two switches, regarding unicast directly-connected routes. I know the second switch has cpu utilization issues and ip unicast failed routes over 4096 arp entries. What would be the case for the first one?
Switch 1:
CAM Utilization for ASIC# 0 Max Used
Masks/Values Masks/values
Unicast mac addresses: 784/6272 12/26
IPv4 IGMP groups + multicast routes: 144/1152 6/26
[Code]...
Cisco Switching/Routing :: How To Debug A TCAM Switch On 877W
Feb 24, 2012I've created a BVI2 where I bridged dot11 0.2 and vlan2 in order to have wired and wireless clients in the same vlan.Some wired client are not reachable from the lan. Wireless clients have no pbl in reaching each other.Monitoring a MAC address that is supposed to be behind the FA2 I have noticed that it moves to vlan2 when in fact it should be behind the FA2.Of course when "show mac-address-table" says it is behind Fa2 the ping to that MAC address works whereas when the TCAM reports it is behind vlan2 it doesn't. Once the MAC address is behind the vlan2 if I clear the mac-address-table and that mac-address is still put behinf Fa2 then the pings works again, sometime I have to perform twice the clear command before the MAC address goes back to the right location.I'd like to understand why the router moves that MAC address from Fa2 to vlan2 and that's the reason for my question in the subject.I don't have any problems for port Fa0 and Fa1."Show int fa2" doesn't show any problem/errors or the likes.BTW even if I force that MAC address to be statically behind FA2 the ping works fine but then stops and if I do "show mac-add" the static entry for it is still there... so looks like there us something that overrides that static entry. If clear everything and I have the mac-address be behind Fa2 then everything starts to work again. I used Fa3 instead of Fa2 and I get the same results.
IOS: c870-advipservicesk9-mz.151-3.T1.bin
Cisco Switching/Routing :: 3750E - Monitoring TCAM Usage
Nov 30, 2011I had a lot of problems with TCAM table in the past and made changes in SDM ended whit that. But now want to be proactive and anticipate the problems in my TCAM table.
If the my template is "default desktop" they support a number of indirect IPv4 routes of 2k. I wanna know automatically by my management tools if this number reaches 1.9k.
That way I can take corrective actions before the problems starts on my network.
Cisco Switching/Routing :: Can TCAM Memory Cause High CPU On 3750 Stack
Sep 12, 2012We have a 3750 stack with a mix of 3750G and 3750X switches. The current active template on the switch is desktop default and we are running EIGRP on the switch with large routing table so we get the TCAM error that a specific prefix cannot be programmed in TCAM memory so it will be software forwarded.%PLATFORM_UCAST-4-PREFIX: One or more, more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded
This error is quite frequent on a daily basis. My question is that will this error create a high CPU situation and affect traffic processing on the stack causing ESX Hosts to become unresponsive?
Cisco Switching/Routing :: 7606 / Netflow TCAM Threshold Exceeded
Nov 6, 2011 following errors.
Nov 7 21:34:50: %EARL_NETFLOW-SP-STDBY-4-TCAM_THRLD: Netflow TCAM threshold exceeded, TCAM Utilization [99%]
Nov 7 21:44:44: %EARL_NETFLOW-SP-4-TCAM_THRLD: Netflow TCAM threshold exceeded, TCAM Utilization [91%]
I've already found this kinds of cases, in this community. So, It seems that Changing the current configuration to 'mls aging fast threshold ## time ## ' is most suitable in our situation.But, I don't know how to calculate the apt threshold value and time value.
[1] sh run | in mls
mls ip multicast flow-stat-timer 9
mls flow ip interface-full
no mls flow ipv6
no mls acl tcam share-global
mls cef error action freeze
[code]....
Cisco Switching/Routing :: TCAM Write Failure Message On 3750x Stack
May 29, 2013I have a stack of 3750x switches running 15.0 (2) SE2 IOS. When I reload the switch stack, I am seeing the following message in the logs: IPv6 user port trust TCAM write failed.
View 2 Replies View RelatedCisco Switching/Routing :: 3750 - Show Interface Vlan (ID) Doesn't Show In / Out Traffic Rate
Mar 13, 2013I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies View RelatedCisco Switching/Routing :: 2960 Don't Display Logging Trap Informational In Show Running / Show Startup
May 27, 2012Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies View RelatedCisco Switching/Routing :: Upgrade 6500 Non Modular IOS To Normal 6500?
Dec 21, 2011how can we upgrade 6500 non modular ios to normal 6500 ios?
View 5 Replies View RelatedIP Configuration Command Won't Show WAN IP
Apr 16, 2011i have ADSL. modem:Meganet when i connect to internet from windows xp with making PPPOE connection everything is fine and when i do ipconfig i can see my IP. but when i connect directly from router then IPconfig show this only:
[code]...
Cisco :: Show Ip Bgp Command Output S / D And H Values?
Aug 1, 2012I have copied status codes from show ip bg command output and its explanation (from Cisco documentation site)., d and h (suppressed, dampened and history). I read somewhere that these are to control flapping routes. But not able to understand it completly.Raised this question in a couple of forums but didnt get a proper reply.The table entry is suppressed.??The table entry is dampened. ??The table entry history. The table entry is validThe table entry is the best entry to use for that network.
View 2 Replies View RelatedCisco :: Show Command To View Ram Modules
Nov 30, 2011Looking for a show command to display the actual physical Ram modules inside a 2911 router. I believe they come with 2x ram slots and I need to know if it has 1 ram stick or 2.show version displays the total amount of ram, but not if its 2x128 or 1x256 etc.This is also production gear so I cannot open it up and have a look until the scheduled downtime.
View 3 Replies View RelatedCisco :: Command To Show Entire Configuration?
May 16, 2011Is there a command that can show EVERYTHING that is configured on a router or switchSeems if you're looking to save enough information to completely swap out a device the run/start config isn't enough.Settings like VTP and MTU settings aren't shown in the config file ... there may be other configuration settings like thisAm I forced to just know to check those settings are is there a command that will show the running-config AND all these other settings that aren't in the config?
View 8 Replies View RelatedCisco WAN :: 887 Doesn't Support Show DSL Command?
Jun 26, 2011The Cisco 887 doesn't support the show dsl command, what is the command that I need to use to display the speed my ADSL is operating at? On the Cisco 877 the command I use is show dsl int atm 0 but this doesn't work on the 887
View 4 Replies View RelatedCisco WAN :: 1841 - Show DSL Interface Command
Jul 15, 2012I'm trying to troubleshoot one of our site today and can't seem to issue the show dsl interface command on a 1841 router. Does the same command is used for SHDSL or am I running with an IOS bug?
#sh dsl?
% Unrecognized command
#sh ver
Cisco IOS Software, 1841 Software (C1841-BROADBAND-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)
Technical Support: {URL}
Compiled Wed 13-Aug-08 15:42 by prod_rel_team
#sh inv
NAME: "chassis", DESCR: "1841 chassis"
PID: CISCO1841 , VID: V05 , SN: FHK13212639
NAME: "WIC/HWIC 0", DESCR: "WAN Interface Card - ATM (With multi line G.SHDSL module)"
PID: WIC-1SHDSL-V3 , VID: V02 , SN: FOC132041KD