I'm trying to troubleshoot one of our site today and can't seem to issue the show dsl interface command on a 1841 router. Does the same command is used for SHDSL or am I running with an IOS bug?
#sh dsl?
% Unrecognized command
#sh ver
Cisco IOS Software, 1841 Software (C1841-BROADBAND-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)
Technical Support: {URL}
Compiled Wed 13-Aug-08 15:42 by prod_rel_team
I have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..Is possible to get these values using SNMP?
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
i have ADSL. modem:Meganet when i connect to internet from windows xp with making PPPOE connection everything is fine and when i do ipconfig i can see my IP. but when i connect directly from router then IPconfig show this only:
i have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
We have a Cisco 1841 router and checked something an unnusual (never seen before) routing table having L - local routes. if this an IOS bug or same as C - connected local routes.
1841#sh verCisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 15.0(1)M3, RELEASE SOFTWARE (fc2)Technical Support: [URL] ... Copyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Sun 18-Jul-10 01:16 by prod_rel_team
I have copied status codes from show ip bg command output and its explanation (from Cisco documentation site)., d and h (suppressed, dampened and history). I read somewhere that these are to control flapping routes. But not able to understand it completly.Raised this question in a couple of forums but didnt get a proper reply.The table entry is suppressed.??The table entry is dampened. ??The table entry history. The table entry is validThe table entry is the best entry to use for that network.
Looking for a show command to display the actual physical Ram modules inside a 2911 router. I believe they come with 2x ram slots and I need to know if it has 1 ram stick or 2.show version displays the total amount of ram, but not if its 2x128 or 1x256 etc.This is also production gear so I cannot open it up and have a look until the scheduled downtime.
Is there a command that can show EVERYTHING that is configured on a router or switchSeems if you're looking to save enough information to completely swap out a device the run/start config isn't enough.Settings like VTP and MTU settings aren't shown in the config file ... there may be other configuration settings like thisAm I forced to just know to check those settings are is there a command that will show the running-config AND all these other settings that aren't in the config?
The Cisco 887 doesn't support the show dsl command, what is the command that I need to use to display the speed my ADSL is operating at? On the Cisco 877 the command I use is show dsl int atm 0 but this doesn't work on the 887
I have a Cisco 2811 and a Cisco 1841 and I cannot get these cards to show up. My IOS for the 1841 is c1841-spservicesk9-mz.124-6.T7 and my IOS for the 2811 is c2800nm-spservicesk9-mz.124-17. When I do a "sh diag" the cards come up as: "unknown daughter card WIC module is not supported/disabled in this slot".
i have 10 stations, and i think one of them generated allot of traffic.maybe a virus sending spam.is there a command that can show my which station consume bandwidth?
My customer has upgrade his 4506 from 6L-E to 7L-E 10GE.Ever since then if he run the command show dot1x interface gigabitEthernet x/x details some information are not been displayed (below are missing information)Is this intensional or do I need to kick this to TAC?
Is there a good reference in how to interpret the "show AP stats" command?
I have a new (online for 15 days) 1142 listed below. It is the first 802.11n AP I've deployed. The stat counters look bad [code] But I don't know how to put it all together to say "here are the stats, this is the problem". I see TxFrameCount, but no corresponding RxFrameCount, so it is hard to calibrate some of the errors. [code]
I am running windows 7 HP. We have about 10 devices in one office and 5 devices connected thru a VPN..... When i hooked everything up 4 weeks ago I could see all the devices in the main office and the remote office connected thru the VPN (In the Network Folder that lists everything connected). Now I only see like 4 device and they are all in the main office.
I did some research a couple weeks ago and found a command prompt that "refreshed" all the devices that were connected, but now They are gone again and I cannot remember the command prompt!
is there a command available to run diagnostics in ASR port/SPA? the one below is from a juniper remote device. i was only able to find 'test interface' but haven't run this yet (currently in production).
I am using cisco c3660 to act as Terminal Server for the communication of production machines in my company, recently there is a communication lost issue happen and its due to physical cable unplug from the machine. to troubleshoot for this issues i have to physically go inside my production area to check on it, as i understand from vendor we can check on the physical machine to see whether the LED light on the module is green or not, but in case of need to troubleshoot at night time, its time consuming as i need to travel back to company. is there any command that i can issue in the router c3660 to check on the physical connection between c3660 router and the production machine? the IOS version is IOS (tm) 3600 Software (C3660-I-M), Version 12.1(4)
I'm trying to configure an Cisco 1841 with IOS 12.4 to an FTTH conection.I would configure PPOE protocol in the vpdn-group 1 but I can't see this option in the command line,I have read about the command "bba-group pppoe global" but i'm not sure if it has the same result. It's valid? How can I use the bba-group pppoe global¿? I need to use it with a virtual template?
We have Nexus 7K recently installed few months back with 2 Sup (Slot 5 & Slot 6).Recently recevied mesaanges in monitoring servervia SNMP:Alarm : active unit removal caused an auto SWACT However, when checked there are no recent logs which may be linked to this alarm. The show redundancy command output shows that Sup in slot 5 is active which in slot 6 is Hot Standby.
I enabled the "no service password-recovery" command on my C2960 switch. All seems to work as discribed. Only issue I have is --- which show command is used to reveal if the password-recovery feature is enabled of disabled as the command doesn't show up in the running config after you enable it ?
NOTE: The command does show up in the C2960 switch in config t mode (unlike the IOS router 2800 series), but doesn't show up in the running-config after you enable or disable it.
On the 2800 series routers (latest IOS) in config t mode the command does not show up but if you type "no service passowrd-recovery" the command function correctly and it does list it in the running configuration.
What is the command to shutdown a cisco 1841 (say, to add a module)? I know how to reload / reboot, but does not seem to find any command with an obvious name.
I have been working on some Catalyst 3750's running 12.2(55)SE6 and hit an issue with CEF load-balancing over multiple equal-cost paths. Anyway this issue is now solved but it introduced me to the command 'show platform forward' - this shows you how the forwarding of a packet would be done via hardware cef (as opposed to the command 'sho ip cef exact-route' command that only shows the software cef path). Anyway I tried the command on a 3560G running 15.0(2)SE and it crashes the switch. I tried it a couple of times and verified that the MAC & IP addresses were exactly right in the command and each time the switch crashes. I have extracted the relevant bits from the crashinfo and attached them.
I am using cisco 1841 LAN router, I need to block MAC address i have applied the command access-list 1102 deny 0000.0000.0000.0000 mac address..... but it does not work.
i've got a Cisco 877 router connected to an ADSL link. i'm using the show dsl interface atm just to have a look on its performance. i've tried to search on Cisco website on how to interpret the output but a blog gave me more info [URL]. My question now is, what readings do i consider? is it on the left (ATU-R) or on the right (ATU-C)?
i have an Issue with my cisco 2801.in the logs shown me the interface FE0/0 cames up some times but never show the down state, I receive my internet service on this interface but never lost the conection, just this logs information
Oct 7 18:39:32.412: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up Oct 7 18:39:41.448: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up Oct 7 21:57:20.775: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up Oct 8 02:29:31.350: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up Oct 8 02:55:12.362: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
