I have a Cisco 2811 and a Cisco 1841 and I cannot get these cards to show up. My IOS for the 1841 is c1841-spservicesk9-mz.124-6.T7 and my IOS for the 2811 is c2800nm-spservicesk9-mz.124-17. When I do a "sh diag" the cards come up as: "unknown daughter card WIC module is not supported/disabled in this slot".
So I am guessing I need a different IOS.
We have a Cisco 1841 router and checked something an unnusual (never seen before) routing table having L - local routes. if this an IOS bug or same as C - connected local routes.
1841#sh verCisco IOS Software,
1841 Software (C1841-IPBASE-M),
Version 15.0(1)M3, RELEASE SOFTWARE (fc2)Technical Support: [URL] ... Copyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Sun 18-Jul-10 01:16 by prod_rel_team
[Code] .....
I wish to use a VWIC2-2MFT-T1/E1 and a VIC2-2BRI-NT/TE in a 2811 -can they co -operate at the same time
View 3 Replies View RelatedI'm trying to troubleshoot one of our site today and can't seem to issue the show dsl interface command on a 1841 router. Does the same command is used for SHDSL or am I running with an IOS bug?
#sh dsl?
% Unrecognized command
#sh ver
Cisco IOS Software, 1841 Software (C1841-BROADBAND-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)
Technical Support: {URL}
Compiled Wed 13-Aug-08 15:42 by prod_rel_team
#sh inv
NAME: "chassis", DESCR: "1841 chassis"
PID: CISCO1841 , VID: V05 , SN: FHK13212639
NAME: "WIC/HWIC 0", DESCR: "WAN Interface Card - ATM (With multi line G.SHDSL module)"
PID: WIC-1SHDSL-V3 , VID: V02 , SN: FOC132041KD
I'm typing this on my Droid X so pardon the typos. I don't really know where to start or what direction to take so I'll list my major problem, then all the facts/info/and actions I've taken to attempt to fix the problem.Problem - I can not connect to the internet and no network adapter shows up under device manager I have an Asus 5671 running windows 7. I purchased the unit about a year ago.It's outside of the manufacturers warranty. Power went out about a week and a half ago and I believe this has something to do with the cause of the problem. I have repeatedly spoken to ASUS about this downloaded the network drivers from their site. When I install them I receive no error message saying they were installed incorrectly or failed to install, but my network adapter still does not show up. I have recovered my computer to factory settings and the problem has not gone away.
While attempting to recover my computer to factory settings, I found out it didn't already come with a recovery disk set up, so I followed the prompts to make a recovery disk (after all this trouble was already happening), so I wonder if creating a recovery disk was pointless since the network issue was already present. I have my router hard lined to my computer, and it's wireless on. The wireless works with my PS3. My computer itself is not wireless. Asus first said the problem was 100% digital, now say it's a hardware problem. I was told I will have to buy a new motherboard to fix the issue.
I have installed a new 2901 router with the IOS version 15 code (c2900-universalk9-mz.SPA.152-3.T.bin). I have a template config that I have created for my remote VPN routers that I have been using on 2811 routers with version 12.4 (c2800nm-advipservicesk9-mz.124-24.T1.bin).I do have the securityk9 active on the 2901 software
Technology Package License Information for Module:'c2900'
-----------------------------------------------------------------
Technology Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------
ipbase ipbasek9 Permanent ipbasek9
security securityk9 Permanent securityk9
uc None None None
data None None None
Issue is when I do a "show crypto session" the GRE tunnels session status read down on the 2901 router but on the 2811 session reads up-active. Everything is working and I am routing over the GRE Tunnels.
[Code] ......
i repalced old cisco router 2811 with new one 2921 , all works except crypto map VPNs routers can ping each other , ACLs are not applied to outbound interfaces show crypto isakmp sa is empty after i make same configuration on a new router 2921 config crypto isakmp policy 10
hash md5
authentication pre-share
crypto isakmp key key address Y.Y.Y.Y no-xauth
[code]...
keys match , crypto isakmp policy is same , IOSs supoort VPN .interess traffic alse been initiated from both side and all worker in old cisco router with same configuration?
i have a question my laptop and my computer does not show the local area connection icon i accidently deleted it and now need to put it back.
View 3 Replies View RelatedJust restarted my Inspiron 1521 and what i see is NO Connection icon.Device manager does not show Dell and Microsoft adapter.
View 2 Replies View RelatedI can't find any specific information on the implementation of packet inspection in a zone based policy firewall. In other words, is there a specification or even just a set of values that define the default inspection parameters for all protocols? With DPI I can manage 'some' of the inspection capabilities but I have some fairly rigorous and specific requirements to meet and I need to validate that the IOS ZBFW will meet those requirements. Specifically, I'm interested in HTTP, DNS, and ICMP but all other protocols would be useful as well.I'm working with basic routers; 871's, 2811's, 1841's, etc. The IOS in use in most cases is adventerprisek9-mz.151-3.T.
View 4 Replies View RelatedI would like to set up a POTS Dial connection between 2 Cisco routers, using the modem card WIC-1AM-V2. I'd like to use this as an out-of-band connection to a remote site, if the primary internet connection fails. So, this setup will only be used in one direction, 1 router placing calls, the other one receiving calls.Here's my config of the receiving router:
chat-script dial "" ATZ AT OK "ATX3D T" ATS0=8 TIMEOUT 120 CONNECT C
interface Async0/2/0 description out of band for network no ip address encapsulation slip async mode interactive
line 0/2/0 session-timeout 5 absolute-timeout 10 script connection dial login local modem InOut transport input all escape-character BREAK autoselect ppp stopbits 1 speed 115200 flowcontrol hardware
[code]....
This config is working fine, when dialing in via a Windows Hyperterminal Dial connection. After a while of dialing I get the login prompt of the router.Now I want to have a router placing calls instead of a Windows Server. I can't figure out how to tell a router to place calls to a POTS phone number.
Receiving router: 2811, WIC-1AM-V2, IOS c2800nm-ipbasek9-mz.124-25a
Calling router: 1841, WIC-1AM-V2, IOS c1841-advsecurityk9-mz.124-25a
I have 2 Cisco routers , 1841 and 2811 , I need to setup site to site VPN , but i dont now some how it just does not seems to be working ,
Find attached the Configuration along with the
<----- 172.31.1.0/24----- DG:172.31.1.1>Cisco 2811<Dialer1 -----//Internet//----------Dialer1>Cisco1841---< DG:10.236.5.254-------------- 10.236.5.0/24--->
Find attached command executed on each router in the below order
1) show ver
2) Show run
3) show logging
4) show crypto ipsec sa
5) show crypto isakmp sa
Debugging enabled on routers are
1)Debug Crypto Isakmp
2) Debug Crypto Ipsec.
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies View RelatedHow to understand "show sessions" and "show connection" commands? And what is the difference between the two?
View 2 Replies View RelatedFacing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies View RelatedI have a cisco 1760 with running VIC-2FXO (working fine). I'm now trying to replace that line with an ISDN line through a VIC2-2BRI.
View 4 Replies View RelatedI am trying to see what traffic goes through a certain ACL so I specify a protocol instead of allow all IP traffic. So what I did is enabled logging with debugging on that ACL. When I right click on the ACL and show log, nothing shows up. But I see hits on the ACL.
View 1 Replies View RelatedI've added several switches and one WLC to my new NCS Prime box. I don't see them in the display. If I try to readd one, it says it already exists. What am I missing?
View 0 Replies View RelatedTrying to get a Cisco ASA 5505 to show me all the current dynamic PAT. (I don't want to see hard-coded port forwarding, just dynamic stuff the router is doing to allow various hosts on the network to talk to the WAN.)
View 8 Replies View Relatedhow to show all the module on the ASR 1004?
View 4 Replies View RelatedI would like to know whether there is any command that shows the configuration of the wireless controller (5508) like when you upload the configuration file from the GUI of the WLC. In other words, I don't want to show me all the verbose running configuration as the "show running-config", but a brief configuration as for example described below: [code]
View 2 Replies View RelatedI have a solution of thre ACS.. one primary and two secondaries. My customer report me that in port of the switch where is connected the ACS show two mac address. [code]
View 1 Replies View RelatedIn a 6500 or 7600 a 'show module' gives a run down on all the modules in the slots, their HW and SW versions and status. But I can't find a similar command in the ASR1006.
View 1 Replies View RelatedI have copied status codes from show ip bg command output and its explanation (from Cisco documentation site)., d and h (suppressed, dampened and history). I read somewhere that these are to control flapping routes. But not able to understand it completly.Raised this question in a couple of forums but didnt get a proper reply.The table entry is suppressed.??The table entry is dampened. ??The table entry history. The table entry is validThe table entry is the best entry to use for that network.
View 2 Replies View RelatedI have two MLS conected by 2 fast ethernet links f0/11 and f0/12 on both sides.I am trying to set up a layer 3 etherchannel using these two links . But when i see etherchannel summary, they dont show up as layer 3. Instead they show as layer 2.
View 19 Replies View RelatedLooking for a show command to display the actual physical Ram modules inside a 2911 router. I believe they come with 2x ram slots and I need to know if it has 1 ram stick or 2.show version displays the total amount of ram, but not if its 2x128 or 1x256 etc.This is also production gear so I cannot open it up and have a look until the scheduled downtime.
View 3 Replies View RelatedIs there a command that can show EVERYTHING that is configured on a router or switchSeems if you're looking to save enough information to completely swap out a device the run/start config isn't enough.Settings like VTP and MTU settings aren't shown in the config file ... there may be other configuration settings like thisAm I forced to just know to check those settings are is there a command that will show the running-config AND all these other settings that aren't in the config?
View 8 Replies View RelatedI've got a 5505 and I'm getting a DHCP address from a cable modem. How can I show the DNS that the ASA is getting? show int vlan 2 is only givving me the IP and net mask.
View 2 Replies View RelatedIn a basic VPN l2l scenario using ezVPN, server behind NAT device, client using 3G. What would be the reason to have in the output of the show crypto ipsec sa, a current peer different from remote crypto endpoint on the server ?
View 3 Replies View RelatedI'm monitoring 2 ASA 5585-x firewalls (in HA mode) using Cisco Prime LMS 4.2.1. The LMS server is connected to the firewalls on the inside interface.
My issue is that I keep on receiving Alert messages on Fault Monitor for both ASA firewalls listing all interfaces (except inside interface) as unresponsive.
My thought is that since the LMS server is not able to ping other active interfaces, it generates these alert messages.
My query is whether I'm thinking right? If yes, how can I prevent these unwanted messages from showing in Fault Monitor?
The Cisco 887 doesn't support the show dsl command, what is the command that I need to use to display the speed my ADSL is operating at? On the Cisco 877 the command I use is show dsl int atm 0 but this doesn't work on the 887
View 4 Replies View Relatedi've got a Cisco 877 router connected to an ADSL link. i'm using the show dsl interface atm just to have a look on its performance. i've tried to search on Cisco website on how to interpret the output but a blog gave me more info [URL]. My question now is, what readings do i consider? is it on the left (ATU-R) or on the right (ATU-C)?
877ROUTER#sh dsl int atm0 ATU-R (DS) ATU-C (US)Modem Status: Showtime (DMTDSL_SHOWTIME)DSL Mode: ITU G.992.1 (G.DMT)ITU STD NUM: 0x01 0x01Vendor ID: 'ALCB' 'ALCB'Vendor Specific: 0x0000 0x0000Vendor Country: 0x00 0x0FCapacity Used: 31% 85%Noise Margin: 34.0 dB 10.0 dBOutput Power: 16.0 dBm 12.0 dBmAttenuation: 10.0 dB 6.0 dBDefect Status: None None Last Fail Code: NoneSelftest Result: 0x00Subfunction: 0x15Interrupts: 1453 (2
[code]....
After some time no using Cisco ACS5.1, I still don't know how I can see all logged in users. I can see logging and check why an log in goes wrong, but in ACS 3.2 I just clicked on Reports and Activity and I could choose to see logged in users, or failed attempts, etc.
View 2 Replies View Related