Cisco WAN :: Show Modules In ASR1006?
Feb 15, 2012In a 6500 or 7600 a 'show module' gives a run down on all the modules in the slots, their HW and SW versions and status. But I can't find a similar command in the ASR1006.
View 1 RepliesIn a 6500 or 7600 a 'show module' gives a run down on all the modules in the slots, their HW and SW versions and status. But I can't find a similar command in the ASR1006.
View 1 RepliesI want to do something with IP SLA and started by estabilishing a baseline.
I'm trying to check history on an ASR. I tested same config on a 3845 and was forgetting the "history filter all". After this I could see history table on 3845 but still history is empty on the ASR1006. The operation started because I can see information with "show ip sla statistics".
know if i missed something or maybe this is not supported in ASR1006?
re-ld-tcc-02_ASR1006#show vers
Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-ADVIPSERVICESK9-M), Version 15.2(1)S2, RELEASE SOFTWARE (fc1)
[Code]......
Looking for a show command to display the actual physical Ram modules inside a 2911 router. I believe they come with 2x ram slots and I need to know if it has 1 ram stick or 2.show version displays the total amount of ram, but not if its 2x128 or 1x256 etc.This is also production gear so I cannot open it up and have a look until the scheduled downtime.
View 3 Replies View RelatedIs there a chart to show what modules will fit what swithches for fiber applications ex 2950 and 3560 switches
View 1 Replies View RelatedWe have:
ASR1000-RP2
ASR1000-ESP40
ASR1000-SIP40
SPA-10X1GE-V2
SPA-10X1GE-V2
!
Kiwi Syslog Server
ASR performs the function of ISG. The number of subscribers until 10000. This number is constantly growing. Because of the economic address space subscribers surf the Internet through NAT.
Now the task to keep logs of all translations or binds. Need to store the information about what time, certain internal IP address using the external IP.
I've tried:
!
ip nat log translations syslog
!
logging trap debugging
logging host xx.xx.xx.xx transport UDP port xxx
no logging console (so as not to load the CPU)
!
Error stopped publishing but logs do not come. I think of the huge number of translation per second, it can not send them as fast. How can this problem be solved or otherwise obtain and store information about a translations?
I'm trying to configure and DMVPN architecture with two routers ASR1006 to server a bank remote offices, one ASR in CO building and the other in CA building (CO: Operational Center; CA: Recovery Center).Each ASR have two LAN connections to internal network and two WAN links to remote office. Each WAN links belongs to differents provider.Each remote office has a router with two WAN links connected to that WAN providers.We are configuring the DMVPN considering two primary tunnels in the CO building and two failover tunnels in CA building.We made the configuration (schemas and configuration attached) but we only get two tunnels up at a time. We cannot ping from office router to four tunnels interfaces in both hubs.
We made some test disabling some tunnels and we could get communication only with two tunnels interfaces. We got communication through tunnels when we have just two.We want to have the four tunnels for high availability. We would like to know how to troubleshoot and make a design review because the examples and documentations are very limited.
my ASR1006 router with the IOS ver:
Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISE-M), Version 12.2(33)XNE, RELEASE SOFTWARE (fc1)
is restarting again and again when I try to write the configuration.
I would like to know if Cisco Collector Engine 6.0 can recive and reading the sent address traslation logging of router ASR1006. Using Netflow v9.
View 4 Replies View Relatedwhy I would see packet loss when BGP comes back up.We have 2 ASR1006's both running full tables of BGP to the same upstream ISP. We load balance the 2 links to them. the ASR's have an OSPF connection between them.When one pipe goes down we see not packet loss; however, when that pipe comes back up we see packet loss until the BGP table fully loads in that router again.
View 1 Replies View RelatedASR performs the function of ISG. The number of subscribers until 10000. This number is constantly growing.Because of the economic address space subscribers surf the Internet through NAT.Now the task to keep logs of all translations or binds. Need to store the information about what time, certain internal IP address using the external IP.
View 19 Replies View RelatedWe have an ASR1006 and I'm just discovering net flow aggregation cache.
I tried prefix aggregation and worked fine. But i cant get any information when checking AS aggregation. All I get is 0 in source and destionation AS. [code]
I have cisco router ASR 1006 .... i need to create PPPOE connection via Ethernet ... and can do that on the management port ???? and what is the type of adapter that use in the Giga Ethernt interface to connect it to fiber ???? hint :- my interface hardware SPA-10X1GE-V2
View 7 Replies View RelatedWhen trying to configure ERSPAN on a ASR1006, I'm not getting any traffic on the destination port. ERSPAN flavour is LOCAL SPAN, as described in:
[URL]
Configuration used, is the following:
monitor session 1 type erspan-source
no shut
source interface GigabitEthernet0/0/2
destination
erspan-id 10
ip address 10.10.10.1
[code].....
Apparently everything is configured in the proper way, however I’m not getting any traffic in the destination port. Also I’ve noticed the following in the details from ‘Session 1’:
Destination IP Address : 10.10.10.1
how to configure Local SPAN using ERSPAN?
I have problems in exporting translations of NAT from my router through NetFlow v9 ASR1006, to my server nfdump, any opensource or licensed software (collector) that I recommend.
ip nat log translations flow-export v9 udp destination 10.1.1.15 1181
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies View RelatedHow to understand "show sessions" and "show connection" commands? And what is the difference between the two?
View 2 Replies View RelatedFacing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies View RelatedThere is an ASR1006 Router in the network that serves as an Intelligent Service Gateway (ISG). Subscribers are layer 2 connected and subscriber sessions are initiated on a DHCP request. ISG is configured as a DHCP relay agent. Wi-Fi clients connect to the WLAN using Open SSID and are being redirected to a Web Portal where they enter their login info. This info is sent to RADIUS server which checks if the user is allowed to use Internet service. All the APs are connected o WLC using CAPWAP. The question is the following: there is a requirement to track from which AP a particular Wi-Fi clients is connected. In this case ISG needs somehow to obtain AP’s mac address and send it to the Radius server (probably using attribute 30 – Called-station-id). One possible way for ISG to obtain AP’s mac is via WLC. But the thing is that when WLC is configured as DHCP proxy and Option 82 is set, a wireless client does not obtain IP address via DHCP. In this particular case there two DHCP relay/proxy in the network path between client and DHCP server. Is there any other away for ISG to obtain AP’s mac address?
View 8 Replies View RelatedI have a cisco 1760 with running VIC-2FXO (working fine). I'm now trying to replace that line with an ISDN line through a VIC2-2BRI.
View 4 Replies View RelatedIs it possible to install Content Security and Control (CSC) Modules on ASA 5505 ? Or only AIP SSC-5 Modules are the only modules that can be installed on ASA 5505s ?
View 3 Replies View RelatedUsing ES2 enhanced etherswitch modules? Could not find out whether it functions identically as NM-16ESW or not. I do understand that ES3 module act like a separate device connected to the router chassis via internal interface and has its own configuration file and processor resources similar to older NME-16ES modules. What about ES2 card (e.g. SM-ES2-24)? Does it work as separate L2 switch connected to the router chassis via trunked internal interface or integrates to the router like the older NME-16ESW module did? Is it possible to turn its ports into the routed mode (no switchport) and use them for L3 forwarding with routing protocols such as OSPF?
View 2 Replies View Relatedhow many NM modules can be inserted into cisco 2821?
View 3 Replies View RelatedDoes cisco LMS v3.2 Support IPV6 in all modules ? We will be migrating from V4 to V6 in some time from now
View 1 Replies View RelatedI would like to know which 2T (like WS-X6848-TX-2T, WS-X6908-10g-2T,...) modules are supported with LMS Prime 4.1 and 4.2.
View 6 Replies View RelatedI have a 6506 with SUP1 MSFC2, running IOS. [code] However, its not able to detect the switch module. [code]
View 6 Replies View RelatedI am facing some issue to activate ,SPA-5X1GE-V2 modules on ASR 1006.
View 1 Replies View RelatedWe had some issue with Datacentre ACE modules. Both primary and DR ACE modules got restarted in 16 hours difference. Unfortunately Syslog was not configured on the ACE and local logging got cleared after restart. The current IOS version is A2(3.2). The modules uptime was around 300 Days. Here is the log from 6509 switch during the restart. [code]
View 7 Replies View RelatedI want to collect the logging messages about the saa5525x IPS events from devices to a server running a syslog daemon, and I have no necessary to collect any other logging messages about the firewall, how would I config the configuration logging?
View 1 Replies View Relatedi m looking for asa 5550 product.Part # ASA5550-BUN-K9 - Cisco ASA 5550 Appliance with SW, HA, 8GE+1FE, 3DES/AES
1) does 5550 contains built in CSC / IPS modules.? why i m asking because the "quick refrence guide " indicates that expansion slots are not available.
2) can asa 5550 natively protects natively against networks attacks against virus / worms etc with out CSC OR IPS MODULE.?
We've recently bought a cisco asr 1001 Router and I have a number of interface slots. I want to populate these with fiber modules.
Which fiber modules are compatible? Are the regular SFPs ok to use or is there a special asr series of SFPs to use?
I have a plan to replace the old routers which are EOL/EOS and i configured the new routers(2921) and modules in Cisco configurator, But i'm stuck with IOS feature set.Old routers are running with IS-IS Protocol, which IOS feature i need to select under 2921 to get the IS IS feature.
View 2 Replies View RelatedI recently purchased a Cisco 5508 WLC and I'm looking to buy some SFP modules but can't find info on which ones would be compatible with the controller on Cisco's website . Is there any module that can support 10Gb as I have a 10Gb on the other end (switch end)?
View 6 Replies View RelatedI had already posted for voice modules for cisco 2811 but not able to find it. But here are a few questions regarding i
1. I am trying to configure a cisco 2811 with FXS ports . I am using an NM-HD-2V with a VIC3-2FXS. I am using the right modules. Also I believe we need PVDM mosules installed in the NM-HD-2V. We have PVDM-12 modules. Will that work or is 2811 compatible only with PVDM2-xx modules.
2. We are also trying to configure a cisco 2811 with PRI port. We plan to use an NM-HD-2V and a VWIC-1MFT-T1/E1. If they are correct and if we need only PVDM2-xx modules.
3. Also we are trying to configure a cisco 3845 with PRI and we plan to use the same as in 2811 that is NM-HD-2V, VWIC-1MFT-T1/E1. And here also we are not sure if we need only PVDM2-xx DSP modules.