Cisco WAN :: How Many NM Modules Can Be Inserted Into 2821
Sep 25, 2012how many NM modules can be inserted into cisco 2821?
View 3 Replieshow many NM modules can be inserted into cisco 2821?
View 3 RepliesHow to get fiber optic modules for Cisco 2821 series router. I can not find anything apart a SFP module which contains only one SFP port.
View 9 Replies View Relatedwhat routed ethernet card (WAN) can be inserted in Cisco 2811? I wan to replace 2Mbps Framerelay to 10 Mbps
View 5 Replies View RelatedI have a Cisco3800 with IOS Version 12.3(14)T2 and I have an HWIC-1GE-SFP module inserted on it.
I need to know if there is a command to verify optical power level in this module inserted in the Cisco 3800 router?
Something similar to the following command that I can execute in an Cisco ASR9K:
show controllers Te0/0/0/1 phy | i Rx
Get the message initializing and then it hangs when I insert the sim card. Have a Rogers wireless stick. a Latitude 2023.
View 3 Replies View RelatedI have a new 8881G-w router with the following info:
(C880DATA-UNIVERSALK9-M), Version 12.4(22)YB2, Serial No. FTX1331830T
Need activating the CDMA . when I tried to login to the Cellular interface it shows me the following warning:Warning: 3G Modem is not inserted Configuration will not be effective until modem is inserted
I want to activate and configure CDMA and i don`t know from to start..
We inserted a new module with 48 rj45 ports in a 4500 with just one supervisor module. We have two 4500, and we tried the new model in the other 4500 and it´s working properly and giving a OK status. Furthermore, the module´s LED status is green. We saw that there are 8 ports (from 17 to 24) that are in faulty state, so probably this is the cause for the faulty state for the module.
We tried already a Hw reset, replace/insert again the module...
We are almost sure that it can be a Hw failure. We are getting the following results different commands:
show module :
Mod Ports Card Type Model Serial No.
7 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 JAXXXXXXXH
M MAC addresses Hw Fw Sw Status
[Code].....
Is it possible to install Content Security and Control (CSC) Modules on ASA 5505 ? Or only AIP SSC-5 Modules are the only modules that can be installed on ASA 5505s ?
View 3 Replies View RelatedUsing ES2 enhanced etherswitch modules? Could not find out whether it functions identically as NM-16ESW or not. I do understand that ES3 module act like a separate device connected to the router chassis via internal interface and has its own configuration file and processor resources similar to older NME-16ES modules. What about ES2 card (e.g. SM-ES2-24)? Does it work as separate L2 switch connected to the router chassis via trunked internal interface or integrates to the router like the older NME-16ESW module did? Is it possible to turn its ports into the routed mode (no switchport) and use them for L3 forwarding with routing protocols such as OSPF?
View 2 Replies View RelatedDoes cisco LMS v3.2 Support IPV6 in all modules ? We will be migrating from V4 to V6 in some time from now
View 1 Replies View RelatedI would like to know which 2T (like WS-X6848-TX-2T, WS-X6908-10g-2T,...) modules are supported with LMS Prime 4.1 and 4.2.
View 6 Replies View RelatedIn a 6500 or 7600 a 'show module' gives a run down on all the modules in the slots, their HW and SW versions and status. But I can't find a similar command in the ASR1006.
View 1 Replies View RelatedLooking for a show command to display the actual physical Ram modules inside a 2911 router. I believe they come with 2x ram slots and I need to know if it has 1 ram stick or 2.show version displays the total amount of ram, but not if its 2x128 or 1x256 etc.This is also production gear so I cannot open it up and have a look until the scheduled downtime.
View 3 Replies View RelatedI have a 6506 with SUP1 MSFC2, running IOS. [code] However, its not able to detect the switch module. [code]
View 6 Replies View RelatedI am facing some issue to activate ,SPA-5X1GE-V2 modules on ASR 1006.
View 1 Replies View RelatedWe had some issue with Datacentre ACE modules. Both primary and DR ACE modules got restarted in 16 hours difference. Unfortunately Syslog was not configured on the ACE and local logging got cleared after restart. The current IOS version is A2(3.2). The modules uptime was around 300 Days. Here is the log from 6509 switch during the restart. [code]
View 7 Replies View RelatedI want to collect the logging messages about the saa5525x IPS events from devices to a server running a syslog daemon, and I have no necessary to collect any other logging messages about the firewall, how would I config the configuration logging?
View 1 Replies View Relatedi m looking for asa 5550 product.Part # ASA5550-BUN-K9 - Cisco ASA 5550 Appliance with SW, HA, 8GE+1FE, 3DES/AES
1) does 5550 contains built in CSC / IPS modules.? why i m asking because the "quick refrence guide " indicates that expansion slots are not available.
2) can asa 5550 natively protects natively against networks attacks against virus / worms etc with out CSC OR IPS MODULE.?
We've recently bought a cisco asr 1001 Router and I have a number of interface slots. I want to populate these with fiber modules.
Which fiber modules are compatible? Are the regular SFPs ok to use or is there a special asr series of SFPs to use?
I have a plan to replace the old routers which are EOL/EOS and i configured the new routers(2921) and modules in Cisco configurator, But i'm stuck with IOS feature set.Old routers are running with IS-IS Protocol, which IOS feature i need to select under 2921 to get the IS IS feature.
View 2 Replies View RelatedI recently purchased a Cisco 5508 WLC and I'm looking to buy some SFP modules but can't find info on which ones would be compatible with the controller on Cisco's website . Is there any module that can support 10Gb as I have a 10Gb on the other end (switch end)?
View 6 Replies View RelatedI had already posted for voice modules for cisco 2811 but not able to find it. But here are a few questions regarding i
1. I am trying to configure a cisco 2811 with FXS ports . I am using an NM-HD-2V with a VIC3-2FXS. I am using the right modules. Also I believe we need PVDM mosules installed in the NM-HD-2V. We have PVDM-12 modules. Will that work or is 2811 compatible only with PVDM2-xx modules.
2. We are also trying to configure a cisco 2811 with PRI port. We plan to use an NM-HD-2V and a VWIC-1MFT-T1/E1. If they are correct and if we need only PVDM2-xx modules.
3. Also we are trying to configure a cisco 3845 with PRI and we plan to use the same as in 2811 that is NM-HD-2V, VWIC-1MFT-T1/E1. And here also we are not sure if we need only PVDM2-xx DSP modules.
I have a WS-C4510R+E with
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 48 10/100/1000BaseT Premium POE E Series WS-X4748-RJ45V+E CAT1612L1JD
2 48 10/100/1000BaseT Premium POE E Series WS-X4748-RJ45V+E CAT1612L1JW
3 12 10GE SFP+ WS-X4712-SFP+E CAT1622L0SC
4 12 10GE SFP+ WS-X4712-SFP+E CAT1622L0RM
5 4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7-E CAT1620L1UJ
6 4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7-E CAT1620L1Z2
Can i add two WS-X4712-SFP+E and two 10 GE ethernet module also?
Is there 10GE ethernet module with WS-C4510R+E.
I've seen a lot of things I want to and need to fix to get our network more secure but my first order of business is Visio diagrams of the old network and projected diagrams of the new network when we move to our new DC next Saturday. I've made maybe 1 diagram on my own thus far and have edited a few. I want to create physical and logical diagrams but I'm not quite sure what to include and what not to include on either since I haven't seen a wealth of diagrams up to this point in my career.
1st question: Does anyone know where I can get visio stencils of IPS modules for ASA 55xx series? Didn't see them on Cisco's stencil site or with a google search
2nd question: Our network is setup like this... A stack of 3 3750s act as our "Core" and have a 2 port etherchannel to every layer 2 2960 switch (15) in the network. In a physical diagram, 30 links would make it a little busy, hell even 15 links represented as the etherchannels would be busy
Is there any option available in any of the Cisco ASA55xx series model to install both csc-ssm and aip-ssm ips modules ? If, so is it advisable to install both ? Is the throughput of ips module has any dependency with the asa chassis throughput ?
View 1 Replies View RelatedI am experiencing an issue with end host being discovered on a cisco 4510. Anything connected to modules 9 or 10 are not discovered in User Tracking. The switch is running: Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.02.01.SG RELEASE SOFTWARE (fc4).
View 1 Replies View RelatedI would like to know if any additional power would be needed for a 3845 (currently with one (1) NME-XD-48ES-2S-P) to which another 24-port switch module is added. Thus, I would have two (2) switch modules on the 3845 for a total of 72 ports.
I have been unable to find specific power requirements detailing the requirements with 1 ethernet module, 2, etc.
We have a 6513 which had 2x 8port (WS-X6708-10GE) 10GB modules one in slot 10 and another in slot 12. Between this two modules we created a 4 port trunk 40GB (2 ports in each module) between the 6513 and a Nexus 7018. Yesterday we swopped one of the moduless for a 16 port 10GB (WS-X6716-10GE) and cannot trunk between the two cards. Only 2 ports work in either one or the other. Seems because of the difference between them (DFC3CXL & DFC3C). Taking a look at the logging we noticed something to the fact of incompatability QOS feature between them.
View 4 Replies View RelatedI want to purchase CISCO2901-SEC/K9 let me know all its specification and how many Ethernet ports supported by its modules?
View 1 Replies View RelatedHere i have a customer who has 7609 router with modules
ws-+6748-ge-tx
ws-svc-wism-1-k9
ws-sup720-3b
ws-sup720-3b
ws-svc-wism-1-k9
ws-6724-sfp
ws-x6704=10ge
ws-x6724-sfp
will this modules will be supported to the new chaisis ios or in the chaisis 7609S
we have a old Nexus 5010 running version 5.0(3)N1(1)it is in a franckenblock(like frankenstein) ie . we bought the parts and create our own system design before VCE was created. He have since bought VCE V block for our production sites. we use the franc ken block to test before we migrate to the production v block 300 FIX the issue we have is the 5010 will only see two 1 Gb/s SFP fiber modules in the first 12 slots. All these slots are dual 1g/10G. If we add more than two, it claims not to see them. We tried swapping the sfp and using both sfg-GE-MM and GLC-SX-MM moduels, no difference at all 1g sfp are in the first 5 slots. only the first two slots are up.the others say "Link not connected" or "SFP not inserted"all five links are the same SFP and are plugged in other switches.the green link lights are on plugged in SFP, even when the CLI states they are not plugged uni tried both two types of 1 Gb/s SFP. sfg-GE-MM and GLC-SX-MM ,i move the sfp between slot 1,2 and 3,4,5. nothing changed,From "sh int brief" you can see that it can see the sfp ie they are all 1Gfrom "sh int status " it sees 1g but why does it say type 10G?why when i go to the "int e 1/5" and try switch port mode now, it can't mode and trunk at now there (;also how to i stop or clear EU51 %SYSMGR-2-TMP_DIR_FULL: System temporary directory usage is unexpectedly high at 87%.i put as much info in the attached file as i could.
View 1 Replies View RelatedI am looking to add the IPS module to my ASA 5510's. I am contemplating only purchasing one module and placing it in the active ASA. I am willing to accept that in a failure scenario I will loose the IPS functionality until the primary ASA is recovered. I have not had a chance to talk to my SE to see if this is even possible. Has anyone attempted a deployment such as this? Will it work and is it supported?
View 3 Replies View RelatedWe are running ACE 20 modules in highly available active / standby (all active contexts on one module) mode. Currently they are on A2 (2.4) version. We are going to upgrade them to A2 (3.6a). The question is that how ling can we run them in two different SW levels? In otherwords can we have few days between upgrading both modules?
View 1 Replies View Related