Cisco WAN :: 6513 - Cannot Trunk Between DFC3CXL And DFC3C Modules

Mar 31, 2011

We have a 6513 which had 2x 8port (WS-X6708-10GE) 10GB modules one in slot 10 and another in slot 12. Between this two modules we created a 4 port trunk 40GB (2 ports in each module) between the 6513 and a Nexus 7018. Yesterday we swopped one of the moduless for a 16 port 10GB (WS-X6716-10GE) and cannot trunk between the two cards. Only 2 ports work in either one or the other. Seems because of the difference between them (DFC3CXL & DFC3C). Taking a look at the logging we noticed something to the fact of incompatability QOS feature between them.

View 4 Replies


ADVERTISEMENT

Cisco Switching/Routing :: 6513 To 3750 Vlan Trunk Connectivity

Nov 8, 2011

Currently we have a 6513 core (running IOS and doing limited routing) with VLAN Trunking to about a dozen 3560 edge switches, with various VLANs going to each of the edge switches.  All works well.  We are downsizing and replacing the 6513 core with a 3750G stack.  We have the stack up and running in the lab, and want to slowly (as we move floors) migrate all of the edge switching to the 3750 stack. 
 
The plan is to connect the 3750 stack to the 6513, then slowly migrate the edge switches to the stack (from the 6513).  I would like to put in place 4 x 1GB trunk links between the 6513 and the 3750 stack before I start moving edge switches to ensure adequate bandwidth.  Once all of the edge switches are on the new 3750 stack, I will start to decommission the 6513.
 
What is the best way to configure the links between the cores (old 6513 and new 3750 stack)?  I can easily get the edge switches configured to the 3750, but am worried about the core links.  I really want to avoid having to perform an all-at-once cutover of the cores.  Another question is when do I try and migrate the VTP server role from the 6513 to the 3750 stack?  I could simply make everything transparent, and ditch server-based VTP, as we rarely change or creat VLANs.

View 3 Replies View Related

Cisco Switching/Routing :: 7606 Need To Install WS-X6748-GE-TX With WS-F6700-DFC3CXL

Nov 13, 2012

I have one Cisco 7606 and i need to install a WS-X6748-GE-TX with WS-F6700-DFC3CXL.When I install the WS-X6748-GE-TX the module is powered off with the following warning:
 
00:01:45: %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 1, power not allowed: Unsupported baseboard/earl combination. [code]

View 1 Replies View Related

Cisco Switching/Routing :: 6513-E / 6513 And WS-X6748-GE-TX Compatibility

Oct 29, 2012

we have a chassis 6513-E and a module WS-X6748-GE-TX, I'd like to know if could I put this module in any slot, since the documentation from Cisco says that any slot from a chassis 6500-E Series can support this module. And then in the documentation of WS-X6748-GE-TX says that this module is not compatible in the slots 1-8 of the 6513 chassis, only from 9th to 13th slots, in those slots from the 6513-E we already have 4x WS-X6748-GE-TX, and we'd like to know if could we put the module in the rest of the slots. The 6513, and 6513-E is kind of confusing.

View 4 Replies View Related

Cisco :: Why Wouldn't Use Spanning - Tree Portfast On Trunk Port Other Than Trunk Between Two Switches

Apr 11, 2013

Is there really any reason why you wouldn't use spanning-tree portfast on a trunk port other than a trunk between two switches? We have it enabled on all ports except for the fiber trunk between two non-stacked switches and the trunk ports connected to our Astaro firewall.I'd like to enable it on the ports to the firewall unless that would cause issues.

View 9 Replies View Related

Cisco Switching / Routing :: WC2948G - Configure LACP Trunk And Multiple Trunk

Feb 12, 2012

we recently aquired a managed services job and have to do a overhaul of the vlan configs and have a whole dozen WC2948G's trunk between a set of ports as well as trunk out a LAG channel setup to non cisco equipment. the deal is the lacp-channel works properly on both ends but no routing of vlans between ports and between the lag trunk are working.
 
theres alot of settings in the config and im planning on clearing it and starting from scratch but before i do i want to know where my problem lies.

[code]...
 

View 6 Replies View Related

Cisco Firewall :: CSC Modules On ASA 5505?

Mar 25, 2012

Is it possible to install Content Security and Control (CSC) Modules on ASA 5505 ? Or only AIP SSC-5 Modules are the only modules that can be installed on ASA 5505s ?

View 3 Replies View Related

Cisco WAN :: ES2 Etherswitch Modules For SrG2

Mar 6, 2011

Using ES2 enhanced etherswitch modules? Could not find out whether it functions identically as NM-16ESW or not. I do understand that ES3 module act like a separate device connected to the router chassis via internal interface and has its own configuration file and processor resources similar to older NME-16ES modules. What about ES2 card (e.g. SM-ES2-24)? Does it work as separate L2 switch connected to the router chassis via trunked internal interface or integrates to the router like the older NME-16ESW module did? Is it possible to turn its ports into the routed mode (no switchport) and use them for L3 forwarding with routing protocols such as OSPF?

View 2 Replies View Related

Cisco WAN :: How Many NM Modules Can Be Inserted Into 2821

Sep 25, 2012

how many NM modules can be inserted into cisco 2821?

View 3 Replies View Related

Cisco :: Does LMS V3.2 Support IPV6 In All Modules

May 1, 2013

Does cisco LMS v3.2 Support IPV6 in all modules ? We will be migrating from V4 to V6 in some time from now

View 1 Replies View Related

Cisco :: 2T Modules Supported With LMS Prime 4.1 And 4.2

Apr 1, 2012

I would like to know which 2T (like WS-X6848-TX-2T, WS-X6908-10g-2T,...) modules are supported with LMS Prime 4.1 and 4.2.

View 6 Replies View Related

Cisco WAN :: Show Modules In ASR1006?

Feb 15, 2012

In a 6500 or 7600 a 'show module' gives a run down on all the modules in the slots, their HW and SW versions and status.  But I can't find a similar command in the ASR1006. 

View 1 Replies View Related

Cisco :: Show Command To View Ram Modules

Nov 30, 2011

Looking for a show command to display the actual physical Ram modules inside a 2911 router. I believe they come with 2x ram slots and I need to know if it has 1 ram stick or 2.show version displays the total amount of ram, but not if its 2x128 or 1x256 etc.This is also production gear so I cannot open it up and have a look until the scheduled downtime.

View 3 Replies View Related

Cisco :: 6506 Unable To Detect Modules

Nov 29, 2011

I have a 6506 with SUP1 MSFC2, running IOS. [code] However, its not able to detect the switch module. [code]

View 6 Replies View Related

Cisco WAN :: To Enable 5X1GE V2 Modules On ASR 1006

Mar 18, 2013

I am facing some issue to activate ,SPA-5X1GE-V2 modules on ASR 1006.

View 1 Replies View Related

Cisco Application :: 6509 ACE Modules Reloaded

Jul 11, 2011

We had some issue with Datacentre ACE modules. Both primary and DR ACE modules got restarted in 16 hours difference. Unfortunately Syslog was not configured on the ACE and local logging got cleared after restart. The current IOS version is A2(3.2). The modules uptime was around 300 Days. Here is the log from 6509 switch during the restart. [code]

View 7 Replies View Related

Cisco Firewall :: Configuration About ASA5525X IPS Modules

Apr 23, 2013

I want to collect the logging messages about the saa5525x IPS events from devices to a server running a syslog daemon, and I have no  necessary  to collect any other logging messages about the firewall, how would I config the configuration logging?               

View 1 Replies View Related

Cisco Firewall :: Does 5550 Contains Built In CSC / IPS Modules

Feb 7, 2011

i m looking for asa 5550 product.Part # ASA5550-BUN-K9 - Cisco ASA 5550 Appliance with SW, HA, 8GE+1FE, 3DES/AES
 
1) does 5550 contains built in CSC / IPS modules.? why i  m asking because the "quick refrence guide " indicates that expansion slots are not available.
 
2) can asa 5550 natively protects natively against networks attacks against virus / worms  etc with out CSC OR IPS MODULE.?

View 9 Replies View Related

Cisco WAN :: ASR 1001 Compatible Fiber Modules?

Aug 14, 2011

We've recently bought a cisco asr 1001 Router and I have a number of interface slots. I want to populate these with fiber modules.

Which fiber modules are compatible? Are the regular SFPs ok to use or is there a special asr series of SFPs to use?

View 15 Replies View Related

Cisco WAN :: Configure New Routers 2921 And Modules

Sep 3, 2011

I have a plan to replace the old routers which are EOL/EOS and i configured the new routers(2921) and modules in Cisco configurator, But i'm stuck with IOS feature set.Old routers are running with IS-IS Protocol, which IOS feature i need to select under 2921 to get the IS IS feature.

View 2 Replies View Related

Cisco Wireless :: 5508 WLC - Compatible SFP Modules?

Dec 10, 2012

I recently purchased a Cisco 5508 WLC and I'm looking to buy some SFP modules but can't find info on which ones would be compatible with the controller on Cisco's website . Is there any module that can support 10Gb as I have a 10Gb on the other end (switch end)?

View 6 Replies View Related

Cisco WAN :: Voice Modules For 2811 And 3845?

Jan 15, 2012

I had already posted for voice modules for cisco 2811 but  not able to find it. But here are a few questions regarding i
 
1. I am trying to configure a cisco 2811 with FXS ports . I am using an NM-HD-2V with a VIC3-2FXS. I am using the right modules. Also I believe we need PVDM mosules installed in the NM-HD-2V. We have PVDM-12 modules. Will that work or  is 2811 compatible only with PVDM2-xx modules.
 
2. We are also trying to configure a cisco 2811 with PRI port. We plan to use an NM-HD-2V and a VWIC-1MFT-T1/E1. If they are correct and if we need only PVDM2-xx modules.
 
3. Also we are trying to configure a cisco 3845 with PRI and we plan to use the same as in 2811 that is NM-HD-2V, VWIC-1MFT-T1/E1. And here also we are not sure if we need only PVDM2-xx DSP modules.

View 7 Replies View Related

Cisco Switching/Routing :: WS-C4510R+E Modules

Feb 7, 2013

I have a WS-C4510R+E with
 
Mod Ports Card Type                              Model              Serial No.
---+-----+--------------------------------------+------------------+-----------
1    48  10/100/1000BaseT Premium POE E Series  WS-X4748-RJ45V+E   CAT1612L1JD
2    48  10/100/1000BaseT Premium POE E Series  WS-X4748-RJ45V+E   CAT1612L1JW
3    12  10GE SFP+                              WS-X4712-SFP+E     CAT1622L0SC
4    12  10GE SFP+                              WS-X4712-SFP+E     CAT1622L0RM
5     4  Sup 7-E 10GE (SFP+), 1000BaseX (SFP)   WS-X45-SUP7-E      CAT1620L1UJ
6     4  Sup 7-E 10GE (SFP+), 1000BaseX (SFP)   WS-X45-SUP7-E      CAT1620L1Z2
 
Can i add two WS-X4712-SFP+E and two 10 GE ethernet module also?
 
Is there 10GE ethernet module with WS-C4510R+E.

View 2 Replies View Related

Cisco :: Get Visio Stencils Of IPS Modules For ASA 55xx Series?

Dec 11, 2011

I've seen a lot of things I want to and need to fix to get our network more secure but my first order of business is Visio diagrams of the old network and projected diagrams of the new network when we move to our new DC next Saturday. I've made maybe 1 diagram on my own thus far and have edited a few. I want to create physical and logical diagrams but I'm not quite sure what to include and what not to include on either since I haven't seen a wealth of diagrams up to this point in my career.

1st question: Does anyone know where I can get visio stencils of IPS modules for ASA 55xx series? Didn't see them on Cisco's stencil site or with a google search

2nd question: Our network is setup like this... A stack of 3 3750s act as our "Core" and have a 2 port etherchannel to every layer 2 2960 switch (15) in the network. In a physical diagram, 30 links would make it a little busy, hell even 15 links represented as the etherchannels would be busy

View 16 Replies View Related

Cisco Firewall :: Option For ASA55xx - To Install Csc-ssm And Aip-ssm IPs Modules

Jul 19, 2012

Is there any option available in any of the Cisco ASA55xx series model to install both csc-ssm and aip-ssm ips modules ? If, so is it advisable to install both ? Is the throughput of ips module has any dependency with the asa chassis throughput ?

View 1 Replies View Related

Cisco :: 4510 Modules 9 Or 10 Are Not Discovered In User Tracking

Feb 21, 2012

I am experiencing an issue with end host being discovered on a cisco 4510.  Anything connected to modules 9 or 10 are not discovered in User Tracking.  The switch is running:  Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.02.01.SG RELEASE SOFTWARE (fc4).

View 1 Replies View Related

Cisco WAN :: Power Requirement For 3845 With Two (2) Switch Modules

Aug 17, 2011

I would like to know if any additional power would be needed for a 3845 (currently with one (1) NME-XD-48ES-2S-P) to which another 24-port switch module is added. Thus, I would have two (2) switch modules on the 3845 for a total of 72 ports.
 
I have been unable to find specific power requirements detailing the requirements with 1 ethernet module, 2, etc.

View 14 Replies View Related

Cisco WAN :: 2901-SEC/ K9 - How Many Ethernet Ports Supported By Its Modules

Dec 22, 2011

I want to purchase CISCO2901-SEC/K9  let me know all its specification and how many Ethernet ports supported by its modules?

View 1 Replies View Related

Cisco Switching/Routing :: Modules Supported In 7609s Or Not

Dec 14, 2011

Here i have a customer who has 7609 router with modules

ws-+6748-ge-tx
ws-svc-wism-1-k9
ws-sup720-3b
ws-sup720-3b
ws-svc-wism-1-k9
ws-6724-sfp
ws-x6704=10ge
ws-x6724-sfp
 
will this modules will be supported to the new chaisis ios or in the chaisis 7609S

View 1 Replies View Related

Cisco Switching/Routing :: Nexus 5010 - Only See Two 1 Gb/s SFP Fibre Modules

Nov 23, 2012

we have a old Nexus 5010 running version 5.0(3)N1(1)it is in a franckenblock(like frankenstein) ie . we bought the parts and create our own system design before VCE was created. He have since bought VCE V block for our production sites. we use the franc ken block to test before we migrate to the production v block 300 FIX the issue we have is the 5010 will only see two 1 Gb/s SFP fiber modules in the first 12 slots. All these slots are dual 1g/10G. If we add more than two, it claims not to see them. We tried swapping the sfp and using both sfg-GE-MM and GLC-SX-MM moduels, no difference at all 1g sfp are in the first 5 slots. only the first two slots are up.the others say "Link not connected" or "SFP not inserted"all five links are the same SFP and are plugged in other switches.the green link lights are on plugged in SFP, even when the CLI states they are not plugged uni tried both two types of 1 Gb/s SFP. sfg-GE-MM and GLC-SX-MM ,i move the sfp between slot 1,2 and 3,4,5. nothing changed,From "sh int brief" you can see that it can see the sfp ie they are all 1Gfrom "sh int status " it sees 1g but why does it say type 10G?why when i go to the "int e 1/5" and try switch port mode now, it can't mode and trunk at now there (;also how to i stop or clear EU51 %SYSMGR-2-TMP_DIR_FULL: System temporary directory usage is unexpectedly high at 87%.i put as much info in the attached file as i could.

View 1 Replies View Related

Cisco Firewall :: IPS Modules In ASA5510 Active / Standby Pair

Feb 6, 2012

I am looking to add the IPS module to my ASA 5510's. I am contemplating only purchasing one module and placing it in the active ASA. I am willing to accept that in a failure scenario I will loose the IPS functionality until the primary ASA is recovered. I have not had a chance to talk to my SE to see if this is even possible. Has anyone attempted a deployment such as this? Will it work and is it supported?

View 3 Replies View Related

Cisco Application Networking :: ACE 20 Modules In Redundant Configuration Upgrade?

Mar 19, 2013

We are running ACE 20 modules in highly available active / standby (all active contexts on one module) mode. Currently they are on A2 (2.4) version. We are going to upgrade them to A2 (3.6a). The question is that how ling can we run them in two different SW levels? In otherwords can we have few days between upgrading both modules?

View 1 Replies View Related

Cisco Switching/Routing :: 7000 Unable To Combine Two Modules In One VDC

Mar 4, 2013

I am having issues trying to combine two modules into one VDC. The modules are as mentioned below: When I try to combine module 1 & 10 as shown above, the nexus 7000 switch displays 'Not compatible'. I've read the online guide and it mentions that the F2 and M1 module cannot be combine into the same VDC. Problem is, my customer has already purchased the module, how do i solve this problem? If I separate the VDC, how does module 1 talk to module 10 if user wants to send traffic to Internet or Server Farm?

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved