Cisco WAN :: ASR 1001 Compatible Fiber Modules?

Aug 14, 2011

We've recently bought a cisco asr 1001 Router and I have a number of interface slots. I want to populate these with fiber modules.

Which fiber modules are compatible? Are the regular SFPs ok to use or is there a special asr series of SFPs to use?

View 15 Replies


ADVERTISEMENT

Cisco Wireless :: 5508 WLC - Compatible SFP Modules?

Dec 10, 2012

I recently purchased a Cisco 5508 WLC and I'm looking to buy some SFP modules but can't find info on which ones would be compatible with the controller on Cisco's website . Is there any module that can support 10Gb as I have a 10Gb on the other end (switch end)?

View 6 Replies View Related

Cisco Switching/Routing :: 10 GB Fiber Modules For 3750G And 3750X

Apr 29, 2013

I am working on a project to connect 2 switch stacks via 10 Gb fiber.  I am told that the 3750Xs do not natively receive the 10 GB SFPs.  What part numbers do i need to order to make this work?  Is there any IOS image requirements?

View 14 Replies View Related

Cisco Switching/Routing :: Get Fiber Optic Modules For 2821 Series Router

Mar 20, 2012

How to get fiber optic modules for Cisco 2821 series router. I can not find anything apart a SFP module which contains only one SFP port.

View 9 Replies View Related

Cisco Switching/Routing :: 2960-S With GLC-FE-100FX Fiber Modules - Packet Loss

Apr 19, 2013

I have two 2960-s switches with GLC-FE-100FX fibre modules in and I am seeing packet loss over the link that is connected to the modules. When the interface is shutdown and brought back up it always comes up in half duplex even thought it is set to full in the config. I've seen other posts where you have to use the command no duplex then full duplex to get it to come up int full duplex. This does appear to work when I do a show int it says its full duplex however I'm stil seeing 20 - 40% packet loss on the link which suggests to me there is still a speed/duplex issue. The device at the other end is a Cisco 7200 which is set to 100Full. If I plug a Cisco 2811 into the fibre link I get zero packet loss which suggests its a problem with the switch.
 
I have changed the modules and fibre cables which makes no difference. As I stated at the start I have two 2960's both are showing exactly the same issue. Details of the switch are below the SFP are cisco branded:

Switch Ports Model              SW Version            SW Image
------ ----- -----              ----------            ----------
*    1 28    WS-C2960S-24TS-L   12.2(55)SE5           C2960S-UNIVERSALK9-M
 
interface GigabitEthernet1/0/25
switchport trunk allowed vlan 380,382,384,386
switchport mode trunk
duplex full(code)

View 18 Replies View Related

Cisco Switching/Routing :: 2950 / 3560 / Chart To Show What Modules Will Fit What Switches For Fiber Applications

Dec 12, 2011

Is there a chart to show what modules will fit what swithches for fiber applications ex 2950 and 3560 switches

View 1 Replies View Related

Cisco WAN :: QoS With ASR 1001

Apr 15, 2013

I've an ASR1001 with 15.1(2)S code on it connected to out ISP, we've been get some complaints about performance and I'm seeing drop on the output policy. Checking the bandwidth consumption we have plenty spare when drops are occuring, there's 300Mb/s.  Details below, any suggestions gratefully received
 
The policy is to guarantee the following bandwidth:
Outbound policy:
class 1 => 50% guaranteed
class 2 => 8% guaranteed
class 3 => 1% guaranteed
class 4 => 5% guaranteed
class 5 => 1% guaranteed
class 6 => 5% guaranteed
class  => 7% guaranteed
class 8 => 7% guaranteed
class default => not configured
 
config :
 
policy-map priority
class 1
priority percent 50
class 2
priority percent 8
class 3
priority percent 1
class 4(code)

View 9 Replies View Related

Cisco WAN :: Does ASR 1001 With IP Base Support BGP

May 15, 2012

I just would like to confirm if the ASR 1001 with IP Base license can support the normal BGP features such as remote-peering IPV4, Local-AS.
 
I am not looking for advanced features such as Route Reflectors, VPLS, L2 VPN, etc.

View 1 Replies View Related

Cisco WAN :: ASR 1001 Console Locking Up

Dec 29, 2012

i have 1001 ASR which boots up ok but shows a warning "filesystem is not clean" and thereafter the image is validated well, it shows up the following two messages and just goes idle from there. [code]

View 6 Replies View Related

Cisco WAN :: ASR 1001 IPBASE Will Support BGP

Feb 20, 2011

We are going to purchase ASR 1001 with ipbase, BGP is our basic requirment if we purchase ipbase(SLASR1-IPB) it will support BGP.

ProductDescriptionASR1001Cisco ASR1001 System,Crypto, 4 built-in GE, Dual P/SASR1001-PWR-ACCisco ASR1001 AC Power SupplyCAB-IND-RAPower Cord India, Right AngleSASR1001UK9-32SCisco ASR 1001 IOS XE - ENCRYPTION UNIVERSALSLASR1-IPBCisco ASR 1000 IP BASE LicenseM-ASR1K-1001-4GBCisco ASR1001 4GB DRAM

View 3 Replies View Related

Cisco WAN :: ASR 1001 - IDC OC3 - T3 / Support VPLS?

Mar 4, 2012

is the ASR 1001 either with IDC OC3 or T3  support VPLS and what is the limitation, what is exactly support is it full functionality of VPLS?

View 4 Replies View Related

Cisco WAN :: ASR 1001- How Interfaces Are Named

Sep 3, 2012

I just need to start building the configuration of an ASR 1001 but I do not know how gigabitethernet interfaces are named on these routers? Are Gi0/0/X or Gi0/X ??

View 1 Replies View Related

Cisco WAN :: ASR 1001 Interface For Vrf Forwarding

Apr 29, 2013

I am replacing my 2900  Internet router with a ASR 1001. I am really not doing anything to fancy on the configuration just routing traffic from the internal LAN to our ISP connection. With the new ASR 1001 there is a configuration for VRF Definition Mgmt-Intf do I do anything with this?  There is also a interface for vrf forwarding. At this point we are just running IPv4.  The plan was just to configure the GigabitEthernet interfaces but I wanted to make sure if I should try and configure VRF.

View 2 Replies View Related

Cisco WAN :: ASR 1001 Router Link Doesn't Come Up

Mar 7, 2013

We have an existing WAN connection from a Cisco 2821 router to Time Warner with a single mode fiber connection using the following SFP:We have a ASR 1001 router configured to replace the 2821 router.  When I connect the fiber into the ASR 1001 router the link does not come up.  I have used the above SFP without success and the following SFP.I have seen Cisco documentation that only certain SFP modules are compatible with ASR router, but I believe the second SFP I listed is compatible.  As a test, I connected my ASR router to a 3750 switch using long haul SFP modules on each end so I know the SFP module works.  The only downside to this test is I only had a multi mode patch cable.  Are there specific settings on the ASR interface that need to be set to allow this connection? 

View 1 Replies View Related

Cisco WAN :: ASR 1001 Unexpected Output Drops

Jan 31, 2012

I have an issue with an ASR 1001. The problem occurs with MQC shaping applied to a gigabit interface in the outbound direction. The CIR of the provider we are using is 100Mb/sec, so we are shaping to that value. However when reported traffic levels are about 60Mb/sec, we see a steady increase in output drops. [code]
 
I have also tried increasing the hold queue, however this does not work with the drops. Increasing the shaping rate to 200Mb/sec gets rid of almost all the drops (not quite all!) but is not what we need. I think that we should see some drops when rates spike above 100mb, however the amount we are seeing seems excessive?

View 1 Replies View Related

Cisco :: ASR 1001 - Adding Routers To NCS Prime?

Jan 20, 2013

This would be the first time I will be working on NCS for a client. There is completely a new install and I was just doing my reading to get my head around the overall working of the product. I had a small Q in mind which I wanted to ask here, while going the config guide, i could not find the way to add a router to the NCS prime. W have ASR 1001 in use along with switches. I read in some forum that NCS supported routers but couldnt find the way in the config guide unless i am missing somewhere. The NCS version is 1.0

View 6 Replies View Related

Cisco WAN :: EIGRP In ASR 1001 Does Not Receive All Route

Aug 8, 2012

We have problem con EIGRP and two ASR 1001 in High Availability. ASR2 have received all route (100 route) from PE, but in ASR1 doesnt received all route (75 route) from PE or from other ASR02. All PE have all route. The ASR1 when modify or lost some route dont update to the ASA. see diagram.

View 5 Replies View Related

Cisco WAN :: Embedded Packet Capture On ASR 1001

Feb 5, 2012

I have a need to capture traffic on an ASR 1001 subinterface, but what I have found is that the Embedded Packet Capture feature is not supported on this platform.  Are there any simple alternatives to capture egress traffic on a subinterface or am I SOL?  This is a walk in the park on normal IOS routers...

View 1 Replies View Related

Cisco AAA/Identity/Nac :: ASR 1001 ACS Won't Pass Authentication

Jul 19, 2011

I'm trying to configure Tacacs on Cisco ASR1001, and the Tacacs server is Cisco ACS v3.3, the ACS won't pass the authentication, complaining bad request from NAS, key mismatch - which I compared millions of times on both ASR and ACS sides. [code]

View 2 Replies View Related

Cisco Firewall :: N2H2 Support On ASR 1001

Aug 31, 2011

A customer recently purchased an ASR 1001 under the impression it could replace their old 3662 router and ASA 5505.  The ASA is configured for their SmartFilter proxy server (N2H2), and I am having a heck of a time finding any documention on how to configure this.  I found the following: To use SmartFilter with Cisco IOS firewall, install the SmartFilter componentsand use the IFP plugin (off-box). To configure the Cisco IOS for SmartFilter,use the Cisco document Firewall N2H2 Support located on the Cisco Web site,[URL]Well, I found the Firewall N2H2 Support document [URL], but the ip inspect command doesn't seem to work on the ASR.  Is there any way to make this work or does the ASA have to stay in line?...

View 3 Replies View Related

Cisco WAN :: Technology Package License For ASR 1001?

May 29, 2012

How can i find the list of features supported in ASR for various license
 
1) IP Base
2) Advance IP Services
3) Advanced Enterprise Services.

View 1 Replies View Related

Cisco Switching/Routing :: Apply A QOS For Traffic LAN In ASR 1001?

Jan 31, 2013

i want to apply a QOS for my trafic LAN, in my ASR 1001 , the LAN is connected with ge0/0/0 interface and it configured with the service instance to bridge vlan 1 ( i do that for OTV ) i put  service policy in "service instance 1" to marking data with ef31  but i noticed that the class "plateform_datacenter" match the trafic and  the ACL associate to this class not mach any trafic trafic !
 
tha policy-map march trafic for Datacenter  :
 sh policy-map interface gigabitEthernet 0/0/0 service instance 1
GigabitEthernet0/0/0: EFP 1
Service-policy input: MARKING-OTV
Class-map: Platforme_DC (match-any) 

[code].....

View 9 Replies View Related

Cisco WAN :: ASR 1001 CBWFQ Not Supported On Subinterfaces And Efps

Mar 19, 2012

I have problems to configure CBWFQ on a ethernet sub-interface on a Cisco Router ASR 1001. Then I applied the policy in the physical interface but it should be is in the sub-interface.  How can I configure CBWFQ on sub-interface in ASR 1001. (version 3.02).
 
Error Messages:
 
CBWFQ: Not supported on subinterfaces and efps
 
This the final output:
 
interface GigabitEthernet0/0/0
description Conexion WAN
bandwidth 153600
no ip address
load-interval 30
no negotiation auto

[code]....

View 2 Replies View Related

Cisco WAN :: 1001 - Connecting 2 Routers To One Edge Router

Mar 6, 2013

My company has purchased a second ASA for fail over reasons and I'm needing to attach it to my core router (ASR 1001). Currently I'm running the connection between my ASA and my Core as a /19   ie. ASA-10.10.10.2/19 -- ASR-10.10.10.1/19. I know the 2nd interface on the ASR will need to be on a different network segment then the first connection (10.10.10.1/19). What would be the best way to segment this out with out breaking up my /19?
 
Run /30 segments for each interface? Use a VLan ?
 
I don't want to use up my Internet rout able IP's on /30 segments. Attached diagram.

View 1 Replies View Related

Cisco Switching/Routing :: ASR 1001 - Trace Route / HSRP / VRF

Mar 24, 2013

when i make a trace route on an ASR 1001 router to 172.23.30.7 I get the following output:
 
VRF info: (vrf in name/id, vrf out name/id)
  1 192.168.99.192 0 msec
    192.168.99.191 1 msec
    192.168.99.192 0 msec
  2 172.23.30.243 1 msec 1 msec 1 msec
  3 172.23.30.7 1 msec 1 msec 1 msec
 
Is there a loop between 192.168.99.191 and .192 (this are two routers with hsrp .190) or is this normal behavior when using trace route on an asr 1001?

View 2 Replies View Related

Cisco Switching/Routing :: ASR 1001 - IKE Phase 2 SA Expires Immediately

Dec 11, 2012

I am migration an IPsec site to site VPN config to a new ASR1001 router «facing» a Linux box (ipsec-tools + racoon). As the Debian Linux does not offer VTI, I am using a crypto map.
 
The working config is given below with the corresponding logs on the Linux side.
 
When I try to apply this previously working config to the ASR1001, I get the following error :
 
000855: *Dec 12 18:28:21.859 UTC: %ACE-3-TRANSERR: IOSXE-ESP(14): IKEA trans 0x1350; opcode 0x60; param 0x2EE; error 0x5; retry cnt 0
 
Dec 12 18:50:19 FAKE-AUCH-GW racoon: INFO: initiate new phase 1 negotiation: 194.214.196.2[500]<=>130.120.124.8[500]
Dec 12 18:50:19 FAKE-AUCH-GW racoon: INFO: begin Identity Protection mode.
Dec 12 18:50:19 FAKE-AUCH-GW racoon: INFO: received Vendor ID: CISCO-UNITY
Dec 12 18:50:19 FAKE-AUCH-GW racoon: INFO: received Vendor ID: DPD
Dec 12 18:50:19 FAKE-AUCH-GW racoon: INFO: received Vendor ID: draft-ietf-ipsra-isakmp-xauth-06.txt(code)

View 8 Replies View Related

Cisco Switching/Routing :: Deploy OTV Using ASR 1001 Between 2 Data-centers?

Apr 9, 2013

deploy OTV using ASR 1001 between 2 data-centers? We want to acquire HSRP localization there, but at this moment I can only see lots docs are saying how to do this on N7K, not ASR. I saw it has a FHRP filtering enabled by default when the OTV configuration is done, and also see there is a access-list created by default call otv_filter_fhrp, Im just wondering besides this IP ACL there should be MAC ACL applied?

View 3 Replies View Related

Cisco Switching/Routing :: ASR 1001 False Environmental Alert

Dec 18, 2011

I have a few new ASR 1001s throwing false environmental alerts.According to the logs, the inlet temp is in excess of 100 degrees C.When I telnet to the routers, they're well within tolerance (30-32C),Running 15.1(1)S and bug toolkit shows no related issues or caveats.

View 1 Replies View Related

Cisco Switching/Routing :: ASR 1001 - Adding Redundant Power Supply?

Dec 23, 2012

I was wondering if I am able to add a redundant power supply to an asr 1001 router that is in production without losing connectivity or causing any diruption to the Users  - is it hotswappable?

View 1 Replies View Related

Cisco Switching/Routing :: ASR 1001 - Configure CoPP / Unwanted Traffic?

Oct 30, 2012

I'm configuring CoPP for an ASR 1001 router with consolidated IOS XE Version: 03.07.01.S.  And I'm trying to use 'DROP' command under policy map to drop.un wanted traffic. But the drop command is not listed.

[code]...

View 6 Replies View Related

Cisco Switching/Routing :: ASR 1001 - License Required To Create IPSec Tunnel?

Oct 26, 2011

what license do I need to create a IPSEC tunnel? I have an ASR 1001, running? [code]

View 2 Replies View Related

Cisco Firewall :: CSC Modules On ASA 5505?

Mar 25, 2012

Is it possible to install Content Security and Control (CSC) Modules on ASA 5505 ? Or only AIP SSC-5 Modules are the only modules that can be installed on ASA 5505s ?

View 3 Replies View Related

Cisco WAN :: ES2 Etherswitch Modules For SrG2

Mar 6, 2011

Using ES2 enhanced etherswitch modules? Could not find out whether it functions identically as NM-16ESW or not. I do understand that ES3 module act like a separate device connected to the router chassis via internal interface and has its own configuration file and processor resources similar to older NME-16ES modules. What about ES2 card (e.g. SM-ES2-24)? Does it work as separate L2 switch connected to the router chassis via trunked internal interface or integrates to the router like the older NME-16ESW module did? Is it possible to turn its ports into the routed mode (no switchport) and use them for L3 forwarding with routing protocols such as OSPF?

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved